纳米TiO2光催化降解硝基酚类污染物动力学及机理的研究

采用纳米TiO₂(P25)粉末作为催化剂,研究了几种典型硝基取代酚在TiO₂/UV悬浮体系下的光催化降解。研究表明，这些化合物的降解过程符合Langmuir-Hinshelwood动力学方程，其表观速率常数(k_app)的大小为：2-氨基-4硝基酚（2-A,4-NP）＞4-硝基酚（4-NP）＞2-硝基酚（2-NP）＞3-硝基酚（3-NP）＞2,4-二硝基酚（2,4-DNP）＞2,4,6-三硝基酚（2,4,6-TNP），而吸附平衡常数(KL)却与k_app成反比。苯环上取代基的种类和数目对有机物光催化降解活性有很大的影响，硝基的加入降低了光催化活性，并且k_app与Hammett常数（σ）具有较好的线性关系。     

微波辅助光催化降解氯酚类污染物的研究

研究了溶液中4-氯酚(4CP)、2-氯酚(2CP)、4-氯-3-甲基酚(4C3MP)、2,4-二氯酚(2,4-DCP)、2,4,6-三氯酚(2,4,6-TCP)和五氯酚(PCP)的微波辅助光催化降解(MW/PCO).结果表明,6种氯酚(CPs)光降解速率与分子中Cl原子取代的数目、位置等分子结构性质有关,单氯酚比多取代氯酚易光解.MW/PCO降解4CP的主要中间产物为苯酚、氯苯、对苯醌、对苯二酚等,降解PCP的主要中间产物为2,3,5,6-四氯对苯醌、2,3,4,6-四氯对苯二酚、四氯酚.CPs降解的机制是紫外光降解和羟基自由基 (·OH)亲电子加成脱氯过程.     

紫外光与超声波耦合对氯酚水溶液的降解研究

选择超声波(US)、紫外光(UV)、紫外光与超声波耦合(UV/US)3种方式对不同位置取代基的单氯酚和不同数目取代基的氯酚进行降解研究。结果表明,UV、US、UV/US对取代基位置不同的单氯酚的降解率大小均为3-氯酚4-氯酚2-氯酚;UV、UV/US对不同取代基数量的氯酚的降解率大小为2-氯酚2,4-二氯酚2,4,6-三氯酚,US单独作用下的降解率大小为2,4,6-三氯酚2,4-二氯酚2-氯酚;UV与US的耦合呈现出较优的协同效应,且耦合降解均以US的降解作用占主导;UV、US、UV/US对氯酚的降解均符合表观一级反应动力学。     

Fe~(3+)掺杂TiO_2/凹凸棒复合材料的光催化性能

采用酸催化的溶胶-凝胶法制备了一系列Fe3+掺杂TiO2/凹凸棒(Fe3+-TiO2/ATP)复合光催化剂材料。在可见光条件下,以亚甲基蓝(MB)溶液的光催化降解反应,评价了样品的光催化性能,研究了TiO2负载量、Fe3+掺杂量和焙烧温度对复合材料光催化性能的影响。在单因素实验的基础上,采用正交实验设计(L25(53))优化了催化剂的制备条件。光催化实验结果表明,MB在复合材料上的光催化降解反应遵循Langmuir-Hinshelwood(L-H)动力学模型。正交实验结果表明,当TiO2负载量为15%、Fe3+掺杂量为0.5%和焙烧温度为550℃时,得到的复合材料对MB的光催化降解效率最佳,测得表观反应速率常数kapp为6.09×10-3min-1,反应4 h后MB的降解率(Dt)可达75.88%,相同实验条件下与P25(1.51×10-3min-1)相比较,反应速率提高了4.03倍,降解率提高了45.05%。另外,复合材料的沉降性能优于P25,易于分离,是一类有应用前景的复合光催化剂。     

La2O3/ZnO/TiO2光催化降解活性艳红K-2BP的研究

采用溶胶-凝胶法制备了La2O3/ZnO/TiO2复合光催化剂,以紫外灯为光源,活性艳红K-2BP为模型降解物,研究了La2O3/ZnO/TiO2的光催化性能.结果表明:当锌和镧的掺杂量w(zno)=20%,w(La2O3)=0.5%,煅烧温度为500℃时,La2O3/ZnO/TiO2复合光催化剂的光催化活件最高;当催化荆投加量4 g/L,通气量800 mL/min,初始pH值3.12时,La2O3/ZnO/TiO2对活性艳红K-2BP的降解效果最好.实验证明.La2O3/ZnO/TiO2对活性艳红K-2BP的降解遵从Lang-muir-Hinshelwood动力学模型,测得其反应速率常数k=11.5 mg/(L·min);吸附常数K=2.88×10-2L/mg.     

改性TiO2对X-3B的光催化性能及其降解动力学研究

以活性艳红X-3B为模型化合物,比较了改性前后TiO2光催化活性的变化.试验结果表明,通过改性大大提高了TiO2的光催化活性,Fe3+和Ag+的掺杂量均有一个最佳值,在试验的掺杂范围内Fe3+和Ag+的最佳掺杂量分别是0.1%和0.05%.对其宏观降解反应动力学的研究表明,X-3B在TiO2、Fe3++TiO2和Ag++TiO2 3种催化剂上的光催化降解动力学均能很好地符合Langmiur-Hinshelwood动力学模型.其表观反应速率常数的大小顺序依次是Ag++TiO2＞Fe3++TiO2＞TiO2;吸附平衡常数则是Fe3++TiO2和Ag++TiO2两者基本相等,两者均比纯TiO2大2～3倍.     

微波辅助光催化降解水中酚的研究

利用改装的家用微波炉和自制的无电极灯(EDL)试验了5种酚在水溶液中的微波辅助光催化降解效果.结果表明,反应30 min,微波辅助光催化作用(MW/EDL/TiO2)能去除80%以上的苯酚、间硝基苯酚、对氯苯酚和对甲酚,相应溶液的总有机碳(TOC)均减少70%以上,2-萘酚的去除率为59%,溶液TOC减少54%;微波(MW或MW/TiO2)作用对酚的去除率有一定贡献;对上述5种酚的微波辅助光催化反应动力学进行了初步研究,发现均符合准一级动力学方程.     

Fe^3＋掺杂TiO2/凹凸棒复合材料的光催化性能

采用酸催化的溶胶-凝胶法制备了一系列Fe^3＋掺杂TiO2/凹凸棒（Fe^3＋-TiO2/ATP）复合光催化剂材料。在可见光条件下,以亚甲基蓝（MB）溶液的光催化降解反应,评价了样品的光催化性能,研究了TiO2负载量、Fe^3＋掺杂量和焙烧温度对复合材料光催化性能的影响。在单因素实验的基础上,采用正交实验设计（L25（53））优化了催化剂的制备条件。光催化实验结果表明,MB在复合材料上的光催化降解反应遵循Langmuir-Hinshelwood（L-H）动力学模型。正交实验结果表明,当TiO2负载量为15%、Fe^3＋掺杂量为0.5%和焙烧温度为550℃时,得到的复合材料对MB的光催化降解效率最佳,测得表观反应速率常数kapp为6.09×10^-3min^-1,反应4 h后MB的降解率（Dt）可达75.88%,相同实验条件下与P25（1.51×10^-3min^-1）相比较,反应速率提高了4.03倍,降解率提高了45.05%。另外,复合材料的沉降性能优于P25,易于分离,是一类有应用前景的复合光催化剂。敏世雄王芳魏立强王永生冯雷佟永纯韩玉琦     

锰掺杂WO3-TiO2复合光催化剂的制备及其性能研究

溶胶-凝胶和浸渍相结合的方法制备锰掺杂WO3-TiO2复合光催化剂,RXD表征,考察WO3和Mn2 掺入量、焙烧温度、焙烧时间及催化剂用量对光催化降解甲基橙的影响.结果表明,500℃焙烧2 h,掺杂量n(Mn2 )∶n(wo3)∶n(TiO2)=0.8∶1∶100时,光催化活性最高,光催化降解甲基橙溶液,120 min后,降解率达90%,比单纯TiO2的光催化活性提高81%.     

固定化催化剂TiO2膜光催化降解三氯乙醛的研究

研究了负载于玻璃上的固定化催化剂TiO2膜光催化降解水中三氯乙醛的效果,探讨了TiO2膜光催化降解三氯乙醛的机理,考察了溶液pH值和三氯乙醛初始浓度埘TiO2膜光催化降解三氯乙醛的影响,并研究了固定化催化剂TiO2膜光催化降解三氯乙醛的动力学.结果表明,固定化催化剂TiO2膜光催化降解水中三氯乙醛的效果良好,当三氯乙醛初始浓度为2.25 mg/L时,在紫外光照时间3 h下,三氯乙醛的降解率高达100%.在相司紫外光照时间下,三氯乙醛的光催化降解率随着三氯乙醛初始浓度的增大而下降.在溶液pH=6.5时,三氯乙醛的降解效率最高.固定化催化剂TiO2膜光催化降解三氯乙醛的反应遵循一级反应动力学,反应速率常数随三氯乙醛初始浓度的增大而减小.     

Solar TiO2-assisted photocatalytic degradation of IGCC power station effluents using a Fresnel lens

The heterogeneous TiO2 assisted photocatalytic degradation of wastewater from a thermoelectric power station under concentrated solar light irradiation using a Fresnel lens has been studied. The efficiency of photocatalytic degradation was determined from the analysis of cyanide and formate removal. Firstly, the influence of the initial concentration of H2O2 and TiO2 on the degradation kinetics of cyanides and formates was studied based on a factorial experimental design. Experimental kinetic constants were fitted using neural networks. Results showed that the photocatalytic process was effective for cyanides destruction (mainly following a molecular mechanism), whereas most of formates (degraded mainly via a radical path) remained unaffected. Finally, to improve formates degradation, the effect of lowering pH on their degradation rate was evaluated after complete cyanide destruction. The photooxidation efficiency of formates reaches a maximum at pH around 5-6. Above pH 6, formate anion is subjected to electrostatic repulsion with the negative surface of TiO2. At pH<4.5, formate adsorption and photon absorption are reduced due to some catalyst agglomeration.     

纳米TiO2光催化氧化去除水中痕量双氯芬酸的研究

以TiCl4为前驱体,采用水解法经不同温度煅烧制备了具有不同理化性能的纳米TiO2光催化剂。利用X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、物理吸附仪、紫外—可见光漫反射吸收光谱(UV-Vis DRS)等手段对纳米TiO2的晶相结构、粒径、孔径分布以及禁带宽度等进行了表征。以蒸馏水配制的双氯芬酸溶液为目标物,进行了纳米TiO2光催化氧化去除双氯芬酸的活性测试,研究了纳米TiO2的理化性能与光催化氧化活性之间的关系。结果表明,经400℃煅烧制得的纳米TiO2样品具有最高的光催化氧化活性,其在紫外光照射60min下对双氯芬酸的去除率为98%左右,比单独紫外光照射高出85百分点。纳米TiO2光催化氧化去除双氯芬酸的反应近似一级反应动力学模型,其中经400℃煅烧制得的纳米TiO2光催化氧化去除双氯芬酸的表观反应速率常数为0.054 54min-1,是普通商用TiO2的2倍左右,与德国Degussa P-25TiO2的光催化氧化活性最相近。     

Solar photocatalytic degradation of mono azo methyl orange and diazo reactive green 19 in single and binary dye solutions: adsorbability vs photodegradation rate

The objective of this study was to examine the effects of adsorbability and number of sulfonate group on solar photocatalytic degradation of mono azo methyl orange (MO) and diazo Reactive Green 19 (RG19) in single and binary dye solutions. The adsorption capacity of MO and RG19 onto the TiO₂ was 16.9 and 26.8 mg/g, respectively, in single dye solution, and reduced to 5.0 and 23.1 mg/g, respectively, in the binary dye solution. The data obtained for photocatalytic degradation of MO and RG19 in single and binary dye solution were well fitted with the Langmuir–Hinshelwood kinetic model. The pseudo-first-order rate constants of diazo RG19 were significant higher than the mono azo MO either in single or binary dye solutions. The higher number of sulfonate group in RG19 contributed to better adsorption capacity onto the surface of TiO₂ than MO indicating greater photocatalytic degradation rate.     

TiO2纳米管催化降解4，4’-二溴联苯的影响因素和动力学研究

利用TiO2纳米管催化降解水中的4，4’-二溴联苯，对催化降解过程和影响因素进行研究。结果表明，TiO2纳米管对其有较高的催化降解效率且降解过程符合Langmuir—Hinshelwood动力学模式。不同光源、4，4’-二溴联苯的初始浓度、纳米管添加量和pH值对催化降解过程都有较大影响，其中pH值的影响最为明显。反应液在中性状态下的降解率明显低于pH=1或11的情况。在pH=1时，4，4’一二溴联苯的降解率达86％。     

Macro kinetic studies for photocatalytic degradation of benzoic acid in immobilized systems

Semiconductor photocatalytic process has been studied extensively in recent years due to its intriguing advantages in environmental remediation. In this study, a two-phase swirl-flow monolithic-type reactor is used to study the kinetics of photocatalytic degradation of benzoic acid in immobilized systems. Transport contributions into the observed degradation rates were determined when catalyst is immobilized. Intrinsic kinetic rate constants and its dependence on light intensity and catalyst layer thickness, values of adsorption equilibrium constant, internal as well as external mass transfer parameters were determined. The simultaneous effect of catalyst loading and light intensity and optimum catalyst layer thickness were also determined experimentally. Reaction rate constants and overall observed degradation rates were compared with slurry systems.     

微波辅助光催化降解阿特拉津的表观动力学

以内分泌干扰物阿特拉津为目标物,建立循环流化床微波辅助光催化体系,研究其微波辅助光催化降解规律。表观动力学研究发现,当阿特拉津初始浓度较低时,其在微波辅助光催化体系中的降解符合表观一级反应动力学特征。降解反应速率常数与阿特拉津初始浓度呈负线性相关,与紫外光强呈正线性相关,与催化剂浓度呈抛物线性相关。表观反应速率常数kobs=3.95×10-4c-0.27030I1.2224W0.3283,该模型计算值与实验值吻合较好,平均相对偏差仅为0.5%,可用于预测微波辅助光催化降解低浓度有机污染物的反应规律。     

Kinetic study and modeling on photocatalytic degradation of para-chlorobenzoate at different light intensities

In order to clarify the dependence of apparent adsorption constant Ks in the Langmuir-Hinshelwood (L-H) model on the incident light intensity, photocatalytic degradation kinetic characteristics were experimentally investigated at different light intensities using para-chlorobenzoate (4-CBA) as a model compound. In all cases 4-CBA initial degradation rates showed dependence on 4-CBA initial concentration, which can be described by the L-H model. However, the adsorption constant Ks and rate constant kr obviously varied with light intensity. To account for the experimental finding, slight modification of the classic kinetic model developed by Turchi and Ollis was tentatively proposed by assuming insufficiency of H2O/OH- available for photo-activated holes' scavenging. Such a kinetic model predicts that both k(r) and Ks(-1) are linearly proportional to the square root of the intensity in a rather large intensity range. The validity of the modified model was proved by fitting it to the experimental data.