Low Concentration Mercury Sorption Mechanisms and Control by Calcium-Based Sorbents: Application in Coal-Fired Processes

ABSTRACT

The capture of elemental mercury (Hg⁰) and mercuric chloride (HgCl₂) by three types of calcium (Ca)-based sor-bents was examined in this bench-scale study under conditions prevalent in coal-fired utilities. Ca-based sorbent performances were compared with that of an activated carbon. Hg⁰ capture of about 40% (nearly half that of the activated carbon) was achieved by two of the Ca-based sorbents. The presence of sulfur dioxide (SO₂) in the simulated coal combustion flue gas enhanced the Hg⁰ capture from about 10 to 40%. Increasing the temperature in the range of 65-100 °C also caused an increase in the Hg⁰ capture by the two Ca-based sorbents. Mercuric chloride (HgCl₂) capture exhibited a totally different pattern. The presence of SO₂ inhibited the HgCl₂ capture by Ca-based sorbents from about 25 to less than 10%. Increasing the temperature in the studied range also caused a decrease in HgCl₂ capture. Upon further pilot-scale confirmations, the results obtained in this bench-scale study can be used to design and manufacture more cost-effective mercury sorbents to replace conventional sorbents already in use in mercury control.     

Resource Recovery from Flue Gas Desulfurization Systems

The cost effective benefits of yielding a flue gas desulfurization (FGD) sludge predominantly composed of CaSO₄·2H₂O, have been previously established. The recovery of this material as FGD by-product gypsum has been demonstrated abroad. Recently U.S. wallboard manufacturers have recognized the viability of this recovery practice. Such techno-economic decision making variables as a) by-product specification, b) transportation costs, and c) location of suitable FGD systems enable the recognition of FGD by-product recovery. Recent investigations of resultant solids content and chloride washing reflect the technical possibility of delivering a suitable product. Commercial and economic factors favor recovery based upon rising disposal and transportation costs. Existing and near term proposed systems surface the technical and commercial problems faced by utilities considering recovery.

Generation of an oxidized FGD sludge consisting of 90⁺% CaSO₄·2H₂O and dewatered to 80⁺% solids is technically achievable by air sparging within the FGD system. Although the product is suitable for land disposal, electric power utilities should consider and evaluate by-product recovery. U.S. wallboard manufacturers have established technical criteria for FGD by-product gypsum. Percent CaSO₄·2H₂O, final solids content, particle size, and chloride content are primarily technical parameters. Technology exists within the FGD industry to satisfy these criteria and results are discussed.

Economic factors comparing mining costs, transportation costs, and disposal costs are developed for specific utility projects. Such comparison established generalized financial criteria for a given utility to develop the economic reasonableness of considering FGD byproduct recovery.

End product user perspectives are presented providing electric utilities with a realistic appreciation for by-product recovery potential. Location of existing wallboard plants highlight potential recovery regions. Quality control problems are discussed in terms of generating a by-product rather than a disposable material.     

Flue Gas Desulfurization: The State of the Art

ABSTRACT

Coal-fired electricity-generating plants may use SO₂ scrubbers to meet the requirements of Phase II of the Acid Rain SO₂ Reduction Program. Additionally, the use of scrubbers can result in reduction of Hg and other emissions from combustion sources. It is timely, therefore, to examine the current status of SO₂ scrubbing technologies. This paper presents a comprehensive review of the state of the art in flue gas desulfurization (FGD) technologies for coal-fired boilers.

Data on worldwide FGD applications reveal that wet FGD technologies, and specifically wet limestone FGD, have been predominantly selected over other FGD technologies. However, lime spray drying (LSD) is being used at the majority of the plants employing dry FGD technologies. Additional review of the U.S. FGD technology applications that began operation in 1991 through 1995 reveals that FGD processes of choice recently in the United States have been wet limestone FGD, magnesium-enhanced lime (MEL), and LSD. Further, of the wet limestone processes, limestone forced oxidation (LSFO) has been used most often in recent applications.

The SO₂ removal performance of scrubbers has been reviewed. Data reflect that most wet limestone and LSD installations appear to be capable of ~90% SO₂ removal. Advanced, state-of-the-art wet scrubbers can provide SO₂ removal in excess of 95%.

Costs associated with state-of-the-art applications of LSFO, MEL, and LSD technologies have been analyzed with appropriate cost models. Analyses indicate that the capital cost of an LSD system is lower than those of same capacity LSFO and MEL systems, reflective of the relatively less complex hardware used in LSD. Analyses also reflect that, based on total annualized cost and SO₂ removal requirements: (1) plants up to ~250 MW_e in size and firing low- to medium-sulfur coals (i.e., coals with a sulfur content of 2% or lower) may use LSD; and (2) plants larger than 250 MW_e and firing medium- to high-sulfur coals (i.e., coals with a sulfur content of 2% or higher) may use either LSFO or MEL.     

Differential partitioning and speciation of Hg in wet FGD facilities of two Spanish PCC power plants

This paper evaluates the speciation and partitioning of mercury in two Spanish pulverised coal combustion power plants (PP1 and PP2), equipped with wet limestone-based flue gas desulphurisation facilities (FGD) operating with forced oxidation and re-circulation of FGD water streams. These plants are fed with coal (PP1) and coal/pet-coke blends (PP2) with different mercury contents. The behaviour, partitioning and speciation of Hg were found to be similar during the combustion processes but different in the FGD systems of the two power plants. A high proportion (86-88%) of Hg escaped the electrostatic precipitator in gaseous form, Hg²⁺ being the predominant mercury species (68-86%) to enter the FGD. At this point, a relatively high total Hg retention (72% and 65%) was achieved in the PP1 and PP2 (2007) FGD facilities respectively. However, during the second sampling campaign for PP2 (2008), the mercury removal achieved by the FGD was much lower (26%). Lab-scale tests point to liquid/gas ratio as the main parameter affecting oxidised mercury capture in the scrubber. The partitioning of the gaseous mercury reaching the FGD system in the wastes and by-products differed. In the low mercury input power plant (PP1) most of the mercury (67%) was associated with the FGD gypsum. Moreover in PP2 a significant proportion of the gaseous mercury reaching the FGD system remained in the aqueous phase (45%) in the 2007 sampling campaign while most of it escaped in 2008 (74%). This may be attributed to the scrubber operating conditions and the different composition and chemistry of the scrubber solution probably due to the use of an additive.     

The Fate and Behavior of Mercury in Coal-Fired Power Plants

Abstract

For the past 22 years in the Netherlands, the behavior of Hg in coal-fired power plants has been studied extensively. Coal from all over the world is fired in Dutch power stations. First, the Hg concentrations in these coals were measured. Second, the fate of the Hg during combustion was established by performing mass balance studies. On average, 43 ± 30% of the Hg was present in the flue gases downstream of the electrostatic precipitator (ESP; dust collector). In individual cases, this figure can vary between 1 and 100%. Important parameters are the Cl content of the fuel and the flue gas temperature in the ESP. On average, 54 ± 24% of the gaseous Hg was removed in the wet flue-gas desulfurization (FGD) systems, which are present at all Dutch coal-power stations. In individual cases, this removal can vary between 8% (outlier) and 72%.

On average, the fate of Hg entering the power station in the coal was as follows: <1% in the bottom ash, 49% in the pulverized fuel ash (ash collected in the ESP), 16.6% in the FGD gypsum, 9% in the sludge of the wastewater treatment plant, 0.04% in the effluent of the wastewater treatment plant, 0.07% in fly dust (leaving the stack), and 25% as gaseous Hg in the flue gases and emitted into the air. The distribution of Hg over the streams leaving the FGD depends strongly on the installation. On average, 75% of the Hg was removed, and the final concentration of Hg in the emitted flue gases of the Dutch power stations was only ~3 μg/m_STP ³ at 6% O₂. During co-combustion with biomass, the removal of Hg was similar to that during 100% coal firing.

Speciation of Hg is a very important factor. An oxidized form (HgCl₂) favors a high degree of removal. The conversion from Hg⁰ to HgCl₂ is positively correlated with the Cl content of the fuel. A catalytic DENOX (SCR) favors the formation of oxidized Hg, and, in combination with a wet FGD, the total removal can be as high as 90%.     

Solving mercury (Hg) speciation in soil samples by synchrotron X-ray microspectroscopic techniques

Direct mercury (Hg) speciation was assessed for soil samples with a Hg concentration ranging from 7 up to 240 mg kg⁻¹. Hg chemical forms were identified and quantified by sequential extractions and bulk- and micro-analytical techniques exploiting synchrotron generated X-rays. In particular, microspectroscopic techniques such as μ-XRF, μ-XRD and μ-XANES were necessary to solve bulk Hg speciation, in both soil fractions <2 mm and <2 μm. The main Hg-species found in the soil samples were metacinnabar (β-HgS), cinnabar (α-HgS), corderoite (Hg₃S₂Cl₂), and an amorphous phase containing Hg bound to chlorine and sulfur. The amount of metacinnabar and amorphous phases increased in the fraction <2 μm. No interaction among Hg-species and soil components was observed. All the observed Hg-species originated from the slow weathering of an inert Hg-containing waste material (K106, U.S. EPA) dumped in the area several years ago, which is changing into a relatively more dangerous source of pollution.     

湿式烟气脱硫系统同时脱汞研究

研究表明，湿法烟气脱硫装置(WFGD)可去除烟气中绝大部分Hg²⁺，但对单质汞的吸收效果不明显，因此研究提高湿法烟气脱硫系统中单质汞的氧化率的方法对控制汞的排放具有重要意义。综述了WFGD及在此系统中各种添加剂的脱汞性能，认为在添加剂中，气态的臭氧、液态的次氯酸和氯化钠稀溶液、 黄磷乳浊液、氢硫化钠溶液及EDTA的汞去除效果较好，且不会被SO₂大量消耗，可在WFGD系统实现同时脱硫脱汞；而气态的氯气，液态的K₂S₂O₈溶液虽然也有较好的汞去除效果，但因易被SO₂或亚硫酸盐溶液消耗，当在WFGD系统中用其氧化单质汞时，需要对脱硫塔进行分层或其他改造，使烟气中的SO₂被吸收后再控制汞，提高经济性。     

Validation of the integrated RAMS-Hg modelling system using wet deposition observations for eastern North America

Using the well-known Regional Atmospheric Modelling System (RAMS) version 4.3 an integrated system able to simulate the atmospheric mercury cycle has been developed. Basic processes of the mercury atmospheric cycle have been incorporated into the atmospheric model. The model deals with elemental Hg (Hg⁰), divalent gaseous Hg (Hg²) and particulate Hg (Hg^P). Wet deposition mechanisms used to describe the removal of Hg² and Hg^P are merged with the detailed cloud microphysical scheme in order to provide better representation of the wet deposition processes. The advantages of this approach have been examined through results intercomparison with simulated Hg wet deposition using CMAQ-Hg from previous work for two evaluation periods: 4 April–2 May 1995, and 20 June–18 July 1995. An attempt to clarify the main parameters that affect wet deposition mechanism of mercury is also made.     

Effects of Sulfur Dioxide and Nitric Oxide on Mercury Oxidation and Reduction under Homogeneous Conditions

Abstract

This paper is particularly related to elemental mercury (Hg⁰) oxidation and divalent mercury (Hg²⁺) reduction under simulated flue gas conditions in the presence of nitric oxide (NO) and sulfur dioxide (SO₂). As a powerful oxidant and chlorinating reagent, Cl₂ has the potential for Hg oxidation. However, the detailed mechanism for the interactions, especially among chlorine (Cl)-containing species, SO₂, NO, as well as H₂O, remains ambiguous. Research described in this paper therefore focused on the impacts of SO₂ and NO on Hg⁰ oxidation and Hg²⁺ reduction with the intent of unraveling unrecognized interactions among Cl species, SO₂, and NO most importantly in the presence of H₂O. The experimental results demonstrated that SO₂ and NO had pronounced inhibitory effects on Hg⁰ oxidation at high temperatures when H₂O was also present in the gas blend. Such a demonstration was further confirmed by the reduction of Hg²⁺ back into its elemental form. Data revealed that SO₂ and NO were capable of promoting homogeneous reduction of Hg²⁺ to Hg⁰ with H₂O being present. However, the above inhibition or promotion disappeared under homogeneous conditions when H₂O was removed from the gas blend.     

Distribution of mercury in the combustion products from coal-fired power plants in Guizhou,southwest China

Method 30B and the Ontario Hydro Method (OHM) were used to sample the mercury in the flue gas discharged from the seven power plants in Guizhou Province, southwest China. In order to investigate the mercury migration and transformation during coal combustion and pollution control process, the contents of mercury in coal samples, bottom ash, fly ash, and gypsum were measured. The mercury in the flue gas released into the atmosphere mainly existed in the form of Hg°. The precipitator shows a superior ability to remove Hg^p (particulate mercury) from flue gas. The removal efficiency of Hg²⁺ by wet flue gas desulfurization (WFGD) was significantly higher than that for the other two forms of mercury. The synergistic removal efficiency of mercury by the air pollution control devices (APCDs) installed in the studied power plants is 66.69–97.56%. The Hg mass balance for the tested seven coal-fired power plants varied from 72.87% to 109.67% during the sampling time. After flue gas flowing through APCDs, most of the mercury in coal was enriched in fly ash and gypsum, with only a small portion released into the atmosphere with the flue gas. The maximum discharge source of Hg for power plants was fly ash and gypsum instead of Hg emitted with flue gas through the chimney into the atmosphere. With the continuous upgrading of APCDs, more and more mercury will be enriched in fly ash and gypsum. Extra attention should be paid to the re-release of mercury from the reutilization of by-products from APCDs.

Implications: Method 30B and the Ontario Hydro Method (OHM) were used to test the mercury concentration in the flue gas discharged from seven power plants in Guizhou Province, China. The concentrations of mercury in coal samples, bottom ash, fly ash, and gypsum were also measured. By comparison of the mercury content of different products, we found that the maximum discharge source of Hg for power plants was fly ash and gypsum, instead of Hg emitted with flue gas through the chimney into the atmosphere. With the continuous upgrading of APCDs, more and more mercury will be enriched in fly ash and gypsum. Extra attention should be paid to the re-release of mercury from the reutilization of by-products from APCDs.     

Sources and deposition of reactive gaseous mercury in the marine atmosphere

Observations of reactive gaseous mercury (RGM) in marine air show a consistent diurnal cycle with minimum at night, rapid increase at sunrise, maximum at midday, and rapid decline in afternoon. We use a box model for the marine boundary layer (MBL) to interpret these observations in terms of RGM sources and sinks. The morning rise and midday maximum are consistent with oxidation of elemental mercury (Hg⁰) by Br atoms, requiring <2 ppt BrO in most conditions. Oxidation of Hg⁰ by Br accounts for 35–60% of the RGM source in our model MBL, with most of the remainder contributed by oxidation of Hg⁰ by ozone (5–20%) and entrainment of RGM-rich air from the free troposphere (25–40%). Oxidation of Hg⁰ by Cl is minor (3–7%), and oxidation by OH cannot reproduce the observed RGM diurnal cycle, suggesting that it is unimportant. Fitting the RGM observations could be achieved in the model without oxidation of Hg⁰ by ozone (leaving Br as the only significant oxidant) by increasing the entrainment flux from the free troposphere. The large relative diurnal amplitude of RGM concentrations implies rapid loss with a lifetime of only a few hours. We show that this can be quantitatively explained by rapid, mass-transfer-limited uptake of RGM into sea-salt aerosols as HgCl₃^? and HgCl₄^2?. Our results suggest that 80–95% of Hg^II in the MBL should be present in sea-salt aerosol rather than gas-phase, and that deposition of sea-salt aerosols is the major pathway delivering Hg^II to the ocean.     

The Adsorptive Capacity of Vapor-Phase Mercury Chloride onto Powdered Activated Carbon Derived from Waste Tires

Abstract

Injection of powdered activated carbon (PAC) upstream of particulate removal devices (such as electrostatic precipitator and baghouses) has been used effectively to remove hazardous air pollutants, particularly mercury-containing pollutants, emitted from combustors and incinerators. Compared with commercial PACs (CPACs), an alternative PAC derived from waste tires (WPAC) was prepared for this study. The equilibrium adsorptive capacity of mercury chloride (HgCl₂) vapor onto the WPAC was further evaluated with a self-designed bench-scale adsorption column system. The adsorption temperatures investigated in the adsorption column were controlled at 25 and 150 °C. The superficial velocity and residence time of the flow were 0.01 m/sec and 4 sec, respectively. The adsorption column tests were run under nitrogen gas flow. Experimental results showed that WPAC with higher Brunauer–Emmett–Teller (BET) surface area could adsorb more HgCl₂ at room temperature. The equilibrium adsorptive capacity of HgCl₂ for WPAC measured in this study was 1.49 × 10^?1 mg HgCl₂/g PAC at 25 °C with an initial HgCl₂ concentration of 25 μg/m³. With the increase of adsorption temperature ≤150 °C, the equilibrium adsorptive capacity of HgCl₂ for WPAC was decreased to 1.×34 10^?1 mg HgCl₂/g PA≤C. Furthermore,WPAC with higher sulfur contents could adsorb even more HgCl₂ because of the reactions between sulfur and Hg²⁺ at 150 °C. It was demonstrated that the mechanisms for adsorbing HgCl₂ onto WPAC were physical adsorption and chemisorption at 25 and 150 °C, respectively. Experimental results also indicated that the apparent overall driving force model appeared to have the good correlation with correlation coefficients (r) >0.998 for HgCl₂ adsorption at 25 and 150 °C. Moreover, the equilibrium adsorptive capacity of HgCl₂ for virgin WPAC was similar to that for CPAC at 25 °C, whereas it was slightly higher for sulfurized WPAC than for CPAC at 150 °C.     

Surface Compositions of Carbon Sorbents Exposed to Simulated Low-Rank Coal Flue Gases

Abstract

Bench-scale testing of elemental mercury (Hg⁰) sorption on selected activated carbon sorbents was conducted to develop a better understanding of the interaction among the sorbent, flue gas constituents, and Hg⁰. The results of the fixed-bed testing under simulated lignite combustion flue gas composition for activated carbons showed some initial breakthrough followed by increased mercury (Hg) capture for up to ～4.8 hr. After breakthrough, the Hg in the effluent stream was primarily in an oxidized form (>90%). Aliquots of selected activated carbons were exposed to simulated flue gas containing Hg⁰ vapor for varying time intervals to explore surface chemistry changes as the initial breakthrough, Hg capture, and oxidation occurred. The samples were analyzed by X-ray photoelectron spectroscopy to determine changes in the abundance and forms of sulfur, chlorine, oxygen, and nitrogen moieties as a result of interactions of flue gas components on the activated carbon surface during the sorption process. The data are best explained by a competition between the bound hydrogen chloride (HCl) and increasing sulfur [S(VI)] for a basic carbon binding site. Because loss of HCl is also coincident with Hg breakthrough or loss of the divalent Hg ion (Hg²⁺), the competition of Hg²⁺ with S(VI) on the basic carbon site is also implied. Thus, the role of the acid gases in Hg capture and release can be explained.     

Simultaneous removal of NOx,SO2, and Hg from flue gas in FGD absorber with oxidant injection (NaClO2)– full-scale investigation

ABSTRACT

This article presents the results of an industrial-scale study (on 400 MW_e lignite fired unit) of simultaneous NO_x, SO₂, and Hg^T removal in FGD absorber with oxidant injection (NaClO₂) into flue gas. It was confirmed that the injection of sodium chlorite upstream the FGD (Flue Gas Desulfurization) absorber oxidize NO to NO₂, Hg⁰ to Hg²⁺, and enhancing NO_x and Hg^T removal efficiency from exhaust gas in FGD absorber. Mercury removal efficiency grows with the rise of degree of oxidation NO to NO₂ and was limited by the phenomenon of re-emission. For NO_x removal the most critical parameters is slurry pH and temperature. There was no negative effect on sulfur dioxide removal efficiency caused by oxidant injection in tested FGD absorber. Based on the data provided, NO_x and Hg^T emissions can be reduced by adjusting the FGD absorber operating parameters combined with oxidant injection.     

Accumulation of mercury and its effect on antioxidant enzymes in brain,liver, and kidneys of mice

Abstract

The effect of mercuric chloride (HgCl₂) on the activities of catalase, Superoxide dismutase (SOD), glutathione peroxidase (GPx), glutathione reductase (GR) and its effect on glutathione (GSH) content were evaluated in different organs (liver, kidneys, and brain) of mice after administration at 0, 0.25, 0.5 and 1.0 mg/kg/day for 14 days. The uptake of mercury shows that the kidneys accumulated the highest levels of mercury compare to brain and liver. The enzyme levels varied in mercury treated organs compare to control. A dose dependent increase of antioxidant enzymes occurred in the liver and kidneys. The increase in enzyme activities correlated with highest mercury accumulation in the kidneys and liver. Mercury is known to generate reactive oxygen species (ROS) in vivo and in vitro, therefore, it is likely that enzyme activities increased to scavenge ROS levels produced as a result of mercury accumulation. Glutathione content increased in liver and kidneys of mercury treated mice compare to control. The results showed that the highest oral dose of mercury significantly increased antioxidant enzymes in kidneys and liver. The increased antioxidant enzymes enhance the antioxidant potential of the organs to reduce oxidative stress.     

Flue gas desulfurization: the state of the art

Coal-fired electricity-generating plants may use SO2 scrubbers to meet the requirements of Phase II of the Acid Rain SO2 Reduction Program. Additionally, the use of scrubbers can result in reduction of Hg and other emissions from combustion sources. It is timely, therefore, to examine the current status of SO2 scrubbing technologies. This paper presents a comprehensive review of the state of the art in flue gas desulfurization (FGD) technologies for coal-fired boilers. Data on worldwide FGD applications reveal that wet FGD technologies, and specifically wet limestone FGD, have been predominantly selected over other FGD technologies. However, lime spray drying (LSD) is being used at the majority of the plants employing dry FGD technologies. Additional review of the U.S. FGD technology applications that began operation in 1991 through 1995 reveals that FGD processes of choice recently in the United States have been wet limestone FGD, magnesium-enhanced lime (MEL), and LSD. Further, of the wet limestone processes, limestone forced oxidation (LSFO) has been used most often in recent applications. The SO2 removal performance of scrubbers has been reviewed. Data reflect that most wet limestone and LSD installations appear to be capable of approximately 90% SO2 removal. Advanced, state-of-the-art wet scrubbers can provide SO2 removal in excess of 95%. Costs associated with state-of-the-art applications of LSFO, MEL, and LSD technologies have been analyzed with appropriate cost models. Analyses indicate that the capital cost of an LSD system is lower than those of same capacity LSFO and MEL systems, reflective of the relatively less complex hardware used in LSD. Analyses also reflect that, based on total annualized cost and SO2 removal requirements: (1) plants up to approximately 250 MWe in size and firing low- to medium-sulfur coals (i.e., coals with a sulfur content of 2% or lower) may use LSD; and (2) plants larger than 250 MWe and firing medium- to high-sulfur coals (i.e., coals with a sulfur content of 2% or higher) may use either LSFO or MEL.     

Atmospheric mercury species in the European Arctic: Measurements and modelling

Concentrations of different species of mercury in arctic air and precipitation have been measured at Ny-Ålesund (Svalbard) and Pallas (Finland) during 1996–1997. Typical concentrations for vapour phase mercury measured at the two stations were in the range of 0.7–2 ng m⁻³ whereas particulate mercury concentrations were below 5 pg m⁻³. Total mercury in precipitation was in the range 3–30 ng l⁻¹. In order to evaluate the transport and deposition of mercury to the arctic from European anthropogenic sources, the Eulerian transport model HMET has been modified and extended to also include mercury species. A scheme for chemical conversion of elemental mercury to other species of mercury and deposition characteristics of different mercury species have been included in the model. European emission inventories for three different forms of Hg (Hg⁰, HgCl₂ and Hg_p) have been implemented in the numerical grid system for the HMET model.     

Technical Description of Parameters Influencing the pH Value of Suspension Absorbent Used in Flue Gas Desulfurization Systems

Abstract

As a result of the large limestone deposits available in Poland, the low cost of reagent acquisition for the large-scale technological use and relatively well-documented processes of flue gas desulfurization (FGD) technologies based on limestone sorbent slurry, wet scrubbing desulfurization is a method of choice in Poland for flue gas treatment in energy production facilities, including power plants and industrial systems. The efficiency of FGD using the above method depends on several technological and kinetic parameters, particularly on the pH value of the sorbent (i.e., ground limestone suspended in water). Consequently, many studies in Poland and abroad address the impact of various parameters on the pH value of the sorbent suspension, such as the average diameter of sorbent particles (related to the limestone pulverization degree), sorbent quality (in terms of pure calcium carbonate [CaCO₃] content of the sorbent material), stoichiometric surfeit of CaCO₃ in relation to sulfur dioxide (SO₂) absorbed from flue gas circulating in the absorption node, time of absorption slurry retention in the absorber tank, chlorine ion concentration in sorbent slurry, and concentration of dissolved metal salts (Na, K, Mg, Fe, Al, and others). This study discusses the results of laboratory-scale tests conducted to establish the effect of the above parameters on the pH value of limestone slurry circulating in the SO₂ absorption node. On the basis of the test results, a correlation equation was postulated to help maintain the desirable pH value at the design phase of the wet FGD process. The postulated equation displays good coincidence between calculated pH values and those obtained using laboratory measurements.     

Investigation of Selective Catalytic Reduction Impact on Mercury Speciation under Simulated NOx Emission Control Conditions

Abstract

Selective catalytic reduction (SCR) technology increasingly is being applied for controlling emissions of nitrogen oxides (NO_x) from coal-fired boilers. Some recent field and pilot studies suggest that the operation of SCR could affect the chemical form of mercury (Hg) in coal combustion flue gases. The speciation of Hg is an important factor influencing the control and environmental fate of Hg emissions from coal combustion. The vanadium and titanium oxides, used commonly in the vanadia-titania SCR catalyst for catalytic NO_x reduction, promote the formation of oxidized mercury (Hg²⁺).

The work reported in this paper focuses on the impact of SCR on elemental mercury (Hg⁰) oxidation. Bench-scale experiments were conducted to investigate Hg⁰ oxidation in the presence of simulated coal combustion flue gases and under SCR reaction conditions. Flue gas mixtures with different concentrations of hydrogen chloride (HCl) and sulfur dioxide (SO₂) for simulating the combustion of bituminous coals and subbituminous coals were tested in these experiments. The effects of HCl and SO₂ in the flue gases on Hg⁰ oxidation under SCR reaction conditions were studied. It was observed that HCl is the most critical flue gas component that causes conversion of Hg⁰ to Hg²⁺ under SCR reaction conditions. The importance of HCl for Hg⁰ oxidation found in the present study provides the scientific basis for the apparent coal-type dependence observed for Hg⁰ oxidation occurring across the SCR reactors in the field.     

EFFECTS OF SELENIUM AND MERCURY ON THE ENZYMATIC ACTIVITIES AND LIPID PEROXIDATION IN BRAIN,LIVER, AND BLOOD OF RATS

Recent studies have reported on the toxicity and related oxidative stress of selenium and mercury. The present study compares the effects of Se as sodium selenite (Na₂SeO₃) and Hg as mercuric chloride (HgCl₂) separately and in combination. Rats received repeated oral doses of Se (0.5 μmol/ml), Hg (0.5 μmol/ml), or Se in combination with Hg (0.5 μmol/ml of each) for 5 consecutive days. Rat serum, brain and liver samples were collected for biochemical assays. The following biochemical alterations occurred in response to Hg treatment: protein content (brain and liver), acetylcholinesterase (AChE) (brain and serum), acid and alkaline (AcP and AlP) phosphatases (plasma and liver) and glutathione S-transferase (GST) (plasma and liver) activities were significantly (P<0.05) decreased, while lactate dehydrogenase (LDH) (plasma, brain and liver), aspartate and alanine aminotransferase (AST, ALT) (serum and liver) activities were significantly increased. Thiobarbituric acid reactive substances (TBARS) was significantly increased in brain and liver. Effect of Se alone included decreased AcP, AlP and GST (serum and liver) activities. However, LDH (serum, brain and liver) and AST (liver) and TBARS (brain and liver) increased. Selenium in combination with Hg partially or totally alleviated the toxic effects of Hg on different studied enzymes. It is concluded that Se could be able to antagonize the toxic effects of mercury.