Optimization of Flow for Forcing Stack Wastes to High Altitudes

It is difficult to control the emission of waste products from large stacks because of the large volume of material to be handled. However, if the waste gas is projected to relatively high altitudes, the problem is less severe in that pollution products are carried to regions of low pollution density. It is especially helpful to accomplish this high altitude dispersal during periods when the air is stable and pollution buildup is most severe. In this paper it is shown that dramatic improvements in the altitude to which stack wastes rise may be obtained by emitting the effluent in discrete vortex rings rather than in steady plumes or forced jets. The parameters of vortex rings required to reach given altitudes under given conditions are calculated. The flow at the stack required to give specific vortex ring parameters is also calculated. Some comments on the type of stack needed to create the desired flow are presented.     

不饱和聚酯树脂生产废水治理技术

不饱和聚酯树脂生产废水CODCr高达 10 0 0 0 0mg/L ,pH为 1— 2 ,且排放无规律 ,处理难度大。采用先对缩聚废水进行蒸馏浓缩 ,再真空泵废水混合调质、降温、缺氧水解后 ,经高效的好氧生物处理工艺 (HCR)处理后与低浓度的冲洗水、生活废水混合 ,进行低负荷的生物接触氧化处理 ,出水CODCr稳定在 10 0mg/L以下。     

Photochemistry and environment IV- Photochemical behaviour of monochlorophenols in dilute aqueous solution

The photochemical behaviour of chlorophenols is different to that of non-halogenated phenols. In the former, the first step is a C-Cl bond scission, which is not influenced by oxygen. Chlorine is converted into hydrochloric acid. For monochlorophenols, the position of the chlorine on the ring strongly influences the transformation. In the molecular form, 2-chlorophenol is converted into pyrocatechol. In the anionic form however, it is reduced in a cyclopentadienic acid which dimerizes according to a Diels-Alder reaction. The irradiation of 3-chlorophenol leads to resorcinol whatever the pH. This would appear to suggest a photohydrolysis mechanism. With 4-chlorophenol, the photochemical conversion is not so specific. Hydroquinone is formed (mainly in aerated solution), along with polyphenolic oligomers. A radical mechanism is proposed.     

Exposure,epidemiology, and mechanism of the environmental toxicant manganese

It has become increasingly apparent that global manganese (Mn) pollution to air and water is a significant threat to human health. Despite this recognition, research is only beginning to comprehend the detrimental effects of exposure. Mn, while essential, is particularly harmful to the central nervous system, and overexposure is symptomatic of several neurological disorders. At-risk populations have been identified, but it is still unclear whether typical exposure levels have any long-term consequences. Those at an elevated risk have diminished intellectual function, learning and memory, and mental development. While the overall mechanism of toxicity is undetermined, Mn has been found to induce oxidative stress, exacerbate mitochondrial dysfunction, dysregulate autophagy, and promote apoptosis, ultimately enhancing neurodegeneration. Extrapolation of this in vitro and in vivo data to humans is difficult. There is a definite need to correlate epidemiological studies with causative effects. It is imperative that research efforts endure, so threats are appropriately identified and exposure properly regulated.     

On the scientific basis for global warming scenarios

The scientific basis for current projections of significant warming due to enhanced minor greenhouse gases in the atmosphere is reviewed. Care is taken to distinguish the issue of changes in radiative forcing at the earth's surface from the issue of the climatic response to this forcing. With respect to the former, it is noted that the predicted forcing is, in fact, small (2 W m(-2) at the surface for a doubling of CO(2), or less than 1% of the absorbed solar flux). With respect to the latter, it is noted that predictions of significant warming are dependent on the presence of large positive feedbacks serving to amplify the response. The largest of these feedbacks in current models involves water vapor at upper levels in the troposphere. This feedback appears to be largely a model artifact, and evidence is presented that models may even have the wrong sign for this feedback. The possibility is examined that the response of climate to major volcanic eruptions may provide a test of the climate system's amplification. The basis for this possibility is the fact that the response delay of the ocean-atmosphere system is proportional to the system gain.     

活性污泥中功能性菌群抗盐度冲击性能研究

利用批量实验研究了活性污泥在受到不同盐度冲击时,其硝化功能、反硝化功能以及生物除磷功能所受到的影响。实验结果表明,活性污泥中亚硝酸菌在氯化钠浓度为10 g/L的环境中,其硝化功能受到86%的的抑制作用;硝酸菌对盐度比亚硝酸菌更敏感,氯化钠浓度为5 g/L时已受到较强的抑制。氯化钠浓度达到50 g/L时,反硝化菌受到46%的抑制作用,反硝化菌对盐度的敏感性比硝化菌低得多。聚磷菌对盐度也很敏感,在氯化钠浓度为20 g/L的环境中,聚磷菌厌氧阶段释磷受到52%的抑制作用;而氯化钠浓度为5 g/L时,好氧阶段吸磷已受到41%的抑制作用。     

The Annual Average: An Alternative to the Second Highest Value as a Measure of Air Quality

It is common practice to use the second highest value both in determining compliance with the once-per-year air quality standards (AQS) and as a measure of air quality in pollutant trend studies and rollback calculations. A study of the variation in the second highest 8 hr carbon monoxide concentration observed at the CAMP stations 1962-72 is presented. It is shown that, for a given annual average, the second highest value can differ by a factor of 2 due to random variation. The annual average is linearly related to the observed average of the second highest value and is shown to be a good predictor of the percent of time the carbon monoxide AQS is exceeded. It is concluded that the annual average, which is less variable and not as greatly influenced by erroneous measurements, is the preferred measure of air quality for trend studies and air quality projections.     

Forewarning model for water pollution risk based on Bayes theory

In order to reduce the losses by water pollution, forewarning model for water pollution risk based on Bayes theory was studied. This model is built upon risk indexes in complex systems, proceeding from the whole structure and its components. In this study, the principal components analysis is used to screen out index systems. Hydrological model is employed to simulate index value according to the prediction principle. Bayes theory is adopted to obtain posterior distribution by prior distribution with sample information which can make samples’ features preferably reflect and represent the totals to some extent. Forewarning level is judged on the maximum probability rule, and then local conditions for proposing management strategies that will have the effect of transforming heavy warnings to a lesser degree. This study takes Taihu Basin as an example. After forewarning model application and vertification for water pollution risk from 2000 to 2009 between the actual and simulated data, forewarning level in 2010 is given as a severe warning, which is well coincide with logistic curve. It is shown that the model is rigorous in theory with flexible method, reasonable in result with simple structure, and it has strong logic superiority and regional adaptability, providing a new way for warning water pollution risk.     

Cost-Effective Enforcement Of Environmental Standards

The body of information presented in this paper is directed to those individuals concerned with cost-effective enforcement of environmental standards. Its aim is twofold. One is to determine some of the differing impacts upon firm behavior of legal enforcement, of economic incentive enforcement, and of mixed legal-economic enforcement. A second objective is to initiate identification of enforcement systems which are most likely to minimize resource costs to firms and enforcement agencies of meeting environmental standards. A computerized model is used to simulate enforcement of the new source particu-late matter discharge standard for coal-fired power plants. Under current legal enforcement it is found that most plants will violate the standard, that small plants will control to higher removal levels than large plants and that firms will install relatively costly pollution control technology. Three enforcement alternatives are considered for overcoming these shortcomings: more stringent legal enforcement, economic incentive enforcement using effluent taxes, and a mixed system which uses device certification tests and effluent taxes. It is found that each of the alternatives can lead to the standard being met and tc more-or-less equal sharing in control burden across plant size. But it is only the two systems which use effluent taxes that give incentive for choosing least costly control technology. It is concluded that the two enforcement systems which use effluent taxes probably would encourage adoption of least cost control technology. This is likely to be a desirable outcome since it may lead to minimum resource costs to power plants and pollution control agencies of meeting fty ash standards. The general applicability of this conclusion to other enforcement situations is discussed.     

Reduction of nitrogen excretion and emission in poultry: A review for organic poultry

Organic poultry is an alternative to conventional poultry which is rapidly developing as a response to customers' demand for better food and a cleaner environment. Although organic poultry manure can partially be utilized by organic horticultural producers, litter accumulation as well as excessive nitrogen still remains a challenge to maintain environment pureness, animal, and human health. Compared to conventional poultry, diet formulation without nitrogen overloading in organic poultry is even more complicated due to specific standards and regulations which limit the application of some supplements and imposes specific criteria to the ingredients in use. This is especially valid for methionine provision which supplementation as a crystalline form is only temporarily allowed. This review is focused on the utilization of various protein sources in the preparation of a diet composed of 100% organic ingredients which meet the avian physiology need for methionine, while avoiding protein overload. The potential to use unconventional protein sources such as invertebrates and microbial proteins to achieve optimal amino acid provision is also discussed.     

Some Factors in Minimizing Precipitator Costs

This paper is directed to those individuals involved in design of electrostatic precipitators. The Deutsch-Anderson model is usually employed by industry for the design of electrostatic precipitators. The so-called process design variable in this approach is the total capture area in the precipitator. Unfortunately, little is available on the equipment design of this unit, i.e., the geometric arrangement of the plates that constitute the capture area and the external dimensions of the physical structure that houses the precipitator components. These are important economic considerations, and it is to this subject that this paper is directed. It is relatively easy to predict equipment costs for “off-the-shelf” electrostatic precipitators; it is more difficult to closely predict the cost for a custom-made unit, which is more often the case encountered in practice. Once the capture area is calculated, the total precipitator cost becomes a strong function of the outer casing and outer accessories of the physical system. In this paper, a model is presented that can help minimize precipitator cost. An illustrative example complements the development of the model.     

ABR反应器的两种快速启动方法对比

ABR反应器的启动是ABR反应器能否高效稳定运行的关键，其影响因素很多。为了更好地实现ABR反应器的启动，提出了通过2种不同启动方法的对比，即1^#反应器采用好氧预挂膜的方法，2^#反应器采用低负荷启动法，得出的结论为，好氧预挂膜启动法的启动时间短，COD去除率高，出水pH稳定，颗粒状污泥生长情况较好，是一种可推广的启动方法。     

Macrodispersion by diverging radial flows in randomly heterogeneous porous media

Radial flow takes place in a heterogeneous porous formation where the transmissivity T is modelled as a stationary random space function (RSF). The steady flow is driven by a given rate, and the mean velocity is radial. A pulse-like of a tracer is injected in the porous formation, and the thin plume spreads due to the fluctuations of the velocity which results a RSF as well. Transport is characterized by the mean front, and by the second spatial moment of the plume. We are primarily interested in tracer macrodispersion modelling. With the neglect of pore-scale dispersion, macrodispersion coefficients are computed at the second order of approximation, without neglecting the head-gradient fluctuations. Although transport is non-ergodic at the source, it is shown that ergodicity is achieved at small distances from the source. This is due to the fact that close to the source local velocities are quite large, and therefore solute particles become uncorrelated very soon. Under ergodic conditions, we compare macrodispersion mechanism in radial flows with that occurring in mean uniform flows. At short distances the spreading effect is highly enhanced by the large variability of the flow field, whereas at large distances transport exhibits a lesser dispersion due to the reduction of velocities. This supports the explanation provided by Indelman and Dagan (1999) to justify why the macrodispersivity is found smaller than that pertaining to mean uniform flows. The model is tested against a tracer transport experiment (Fernàndez-Garcia et al., 2004) by comparing the theoretical and experimental breakthrough curves. The accordance with real data, that is achieved without any fitting to concentration values, strengthens the capability of the proposed model to grasp the main features of such an experiment, the approximations as well as experimental uncertainties notwithstanding.     

Analysis of chemical and physical effects of ultraviolet bulbs on cooking emissions

There is a growing recognition of the risks to health, fire hazard, and air quality from cooking emissions. Recent research has identified what is emitted when foods are cooked. Some of the emitted mass is captured in the exhaust system. The balance is expelled into the atmosphere. The outlet of the exhaust system is a demarcation point-upstream the captured mass is the operator or building owner's concern, whereas downstream into the atmosphere, it affects air quality. Building codes have long required operators to deal with the upstream section. More recently, regulations are being placed on what kitchens can emit to the atmosphere. The industry is responding to this challenge with product innovations. Recently gained understanding of cooking emissions supports much of the innovation-but not all. This paper evaluates the purported benefit of adding better filtration and ultraviolet C (UVC) bulbs in kitchen hoods. A "UV hood" claims a two-step process to reduce emissions: better filters capture more emitted mass, and UVC photons and ozone drive photo-decomposition and oxidation reactions of some of the remaining greasy constituents. Adding UV to a hood at least doubles the cost compared to an equivalent non-UV hood. There is evidence that UV hoods do reduce some emissions. The essential question is whether improved performance is due to UV or relatively inexpensive, improved filters. Experimentation exposed an oleic acid aerosol, representative of cooking emissions, to UVC energy and ozone at higher concentrations and for longer exposure times than can occur in a UV hood. Particle-size and chemical changes were measured on samples collected with UV bulbs off and on. Results strongly indicate little change is happening and most emission reductions are caused by better filtration and not UV. The conclusion is that UV hoods fall short of claimed performance, and unreacted ozone may increase air pollution.     

Small-scale spatial and temporal variance in the concentration of heavy metals in aquatic sediments: a review and some new concepts.

Uncertainty associated with data derived by the analyses of heavy metals in aquatic sediment is due to variance produced in the laboratory (precision), plus 'natural', small-scale spatial variance, (or field variance) at the sampling site. Precision is easily determined and is usually reported in contaminant studies, but field variance is poorly understood and seldom documented. It is important to have an understanding of the field variance because if small-scale spatial variance in the concentration of heavy metals is excessive, regional trends may be limited value. Similarly, if temporal change is large, the results of single synoptic surveys may be questionable and the ability to demonstrate anthropogenic contributions over time will be difficult. However, it is evident from the literature that the information needed to address problems of spatial and temporal variance in the field is beyond the resources of most researchers. Analytical precision of about 5% relative standard deviation (RSD) for heavy metal analysis is typical of a well-managed laboratory. Many studies of small-scale spatial variability made during the current investigation indicate that field variance is related to ambient energy and to the type of sedimentological environment. Total variance (analytical plus field variance) is approximately 10% RSD (mean for a suite of nine trace elements) for depositional parts of estuaries and the marine environment, but increases to about 20-35% RSD for the more dynamic parts of the estuarine environment and the fluvial system. Repeated sampling over periods of up to 7 years undertaken during the present study, indicate a similar order of magnitude for temporal variability in these sedimentological environments. A proposed scheme to provide information on field variance is to undertake small-scale spatial and temporal studies in discrete sedimentological environments in the study area after sediment sampling and characterisation has been completed. The comparatively large proportion of total variance associated with small-scale spatial and temporal variability in the field questions the often excessive cost and effort made in attempting minor reductions in analytical precision in contaminant investigations.     

基于基尼系数的乌梁素海流域污染负荷分配

在水体污染物总量控制分配中,科学合理地分配污染物排放指标是实施水体环境管理的关键.将应用在经济领域衡量居民收入分配公平程度的基尼系数引入环境领域,提出环境基尼系数这一新概念用于解决流域内各分区污染物总量控制分配的问题.以乌梁素海流域为例,分别以流域内各分区人口、水资源量和国内生产总值(GDP)作为流域内基尼系数的分配指...     

State-space modeling of the relationship between air quality and mortality

A portion of a population is assumed to be at risk, with the mortality hazard varying with atmospheric conditions including total suspended particulates (TSP). This at-risk population is not observed and the hazard function is unknown; we wish to estimate these from mortality count and atmospheric variables. Consideration of population dynamics leads to a state-space representation, allowing the Kalman Filter (KF) to be used for estimation. A harvesting effect is thus implied; high mortality is followed by lower mortality until the population is replenished by new arrivals. The model is applied to daily data for Philadelphia, PA, 1973-1990. The estimated hazard function rises with the level of TSP and at extremes of temperature and also reflects a positive interaction between TSP and temperature. The estimated at-risk population averages about 480 and varies seasonally. We find that lags of TSP are statistically significant, but the presence of negative coefficients suggests their role may be partially statistical rather than biological. In the population dynamics framework, the natural metric for health damage from air pollution is its impact on life expectancy. The range of hazard rates over the sample period is 0.07 to 0.085, corresponding to life expectancies of 14.3 and 11.8 days, respectively.     

汽车尾气净化催化剂涂层改性研究

汽车尾气净化催化剂的净化转化效果及其耐久性,与催化剂涂层的涂覆量以及涂层和载体的结合强度密切相关.本文研究了几种不同类型表面活性剂对浆料固体含量、涂层涂覆量以及涂层结合强度的影响.研究结果表明,不使用表面活性剂时,30%为最佳的固体含量;在使用表面活性剂的情况下,浆料的固体含量可以提高至35%.非离子型表面活性剂有助于提高催化剂涂层涂覆量,而使用离子型表面活性剂的浆料球磨过程中产生大量泡沫,无法涂覆.使用非离子型表面活性剂的催化剂涂层的结合强度最好.     

Particulate organic compounds emitted from motor vehicle exhaust and in the urban atmosphere

The emission rate of particle-phase petroleum biomarkers in vehicular exhaust compared to the concentrations of these biomarkers in ambient air is used to determine the particulate organic compound concentration due to primary particle emissions from motor vehicles in the southern California atmosphere. A material balance on the organic particulate matter emitted from motor vehicle traffic in a Los Angeles highway tunnel first is constructed to show the proportion which is solvent-extractable and which will elute from a GC column, the ratio of resolved to unresolved compound mass, the portion of the resolved material that can be identified as single organic compounds, and the contribution of different classes of organic compounds to the overall identified fraction. It is shown that the outdoor ambient concentrations of the petroleum biomarkers track primary emissions measured in the highway tunnel, confirming that direct emissions of these compounds from vehicles govern the observed ambient petroleum biomarker concentrations. Using organic chemical tracer techniques, the portion of fine organic particulate matter in the Los Angeles atmosphere which is attributable to direct particle emissions from vehicle exhaust is calculated to vary from 7.5 to 18.3% at different sites throughout the air basin during a summertime severe photochemical smog episode. A similar level of variation in the contribution of primary motor vehicle exhaust to fine particulate organic matter concentrations during different times of day is seen. While peak atmospheric concentrations of fine particulate organic carbon are observed during the 1200–1600 PDT afternoon sampling period, only 6.3% of that material is apportioned to the directly emitted particles from vehicle exhaust. During the morning traffic peak between 0600–1000 PDT, 19.1% of the fine particulate organic material is traced to primary emissions from motor vehicles.     

On spurious water flow during numerical simulation of steam injection into water-saturated soil

Numerical simulation of steam injection into a water-saturated porous medium may be hindered by unphysical behavior causing the model to slow down. We show how spurious water flow may arise on the boundary between a steam zone and a saturated zone, giving rise to dramatic pressure drops. This is caused by the discretization of the temperature gradient coupled with the direct relation between pressure and temperature in the steam zone. The problem may be a severe limitation to numerical modeling. A solution is presented where the spurious water flow is blocked and this widely enhances the performance of the model. This new method is applied to a previously reported example exhibiting numerical problems. Furthermore, it is applied to the simulation of 2-D sandbox experiments where LNAPL is remediated from a smearing zone by steam injection. These experiments would have been difficult to analyze numerically without the adjustment to prevent spurious flow.