Bioremediation of a weathered and a recently oil-contaminated soils from Brazil: a comparison study

The facility with which hydrocarbons can be removed from soils varies inversely with aging of soil samples as a result of weathering. Weathering refers to the result of biological, chemical and physical processes that can affect the type of hydrocarbons that remain in a soil. These processes enhance the sorption of hydrophobic organic contaminants (HOCs) to the soil matrix, decreasing the rate and extent of biodegradation. Additionally, pollutant compounds in high concentrations can more easily affect the microbial population of a recently contaminated soil than in a weathered one, leading to inhibition of the biodegradation process. The present work aimed at comparing the biodegradation efficiencies obtained in a recently oil-contaminated soil (spiked one) from Brazil and an weathered one, contaminated for four years, after the application of bioaugmentation and biostimulation techniques. Both soils were contaminated with 5.4% of total petroleum hydrocarbons (TPHs) and the highest biodegradation efficiency (7.4%) was reached for the weathered contaminated soil. It could be concluded that the low biodegradation efficiencies reached for all conditions tested reflect the treatment difficulty of a weathered soil contaminated with a high crude oil concentration. Moreover, both soils (weathered and recently contaminated) submitted to bioaugmentation and biostimulation techniques presented biodegradation efficiencies approximately twice as higher as the ones without the aforementioned treatment (natural attenuation).     

Tolerance to trichlorophenols in microorganisms from a polluted and a pristine site of a river

The effect of 2,4,5- and 2,4,6-trichlorophenol on the microbiota from a polluted and a pristine site of a river was studied. Bacterial metabolic activity measurements by epifluorescence microscopy showed that the polluted site contained more metabolically active cells than the pristine site. Total culturable bacterial counts and tolerant bacterial counts from both sites were not affected by incubation (for up to 5 days) with 200 ppm of chlorophenols. However, the incubation with 500 ppm of 2,4,5-trichlorophenol prevented detection of total and tolerant bacterial counts in the pristine site, and inhibited tolerants in the polluted site. None of 250 bacterial colonies directly isolated from these samples was able to grow on chlorophenols. However, bacteria able to grow on 2,4,6-trichlorophenol, were obtained by enrichment of water and sediments samples.     

Chromium Analysis at a Ferrochrome Smelter,a Chemical Plant and a Refractory Brick Plant

Techniques were developed to sample and analyze the Cr content of participate samples with emphasis on determining the concentration of the carcinogen Cr⁺⁶. Cr⁺⁶ is extracted to alkaline solution and analyzed colorimetrically. Residual particles are extracted with acid solution to remove soluble Cr⁺³, which is determined by atomic absorption spectrometry. This methodology was tested on samples from three diverse types of sources: a ferrochrome smelter, a chemical plant, and a refractory brick plant. Identical quadruplicate samples were collected to determine accuracy and precision of the collection and analysis procedures, and extraction of Cr⁺⁶ and Cr⁺³. A statistical analysis revealed that the precision of Cr⁺⁶ analysis is comparable to that of the particulate mass determination. The stability of Cr⁺⁶ In particulate form and in solution was determined. Size resolved particulate samples were collected to determine the particle size versus the Cr⁺⁶ content. At the ferrochrome smelter and the chemical plant the majority of the Cr⁺⁶ was contained in the respirable particles. The accuracy and completeness of the chemical methods employed were verified by neutron activation analysis, x-ray photoelectron spectroscopy, and scanning electron microscopyenergy dispersive x-ray analysis.     

Biological treatment of a contaminated gaseous emission from a leather industry in a suspended-growth bioreactor

A suspended-growth bioreactor (SGB) was operated for the treatment of a gaseous stream mimicking emissions generated at a leather industrial company. The main volatile organic compounds (VOCs) present in the gaseous stream consisted of 1-methoxy-2-propanol, 2,6-dimethyl-4-heptanone, 2-butoxyethanol, toluene and butylacetate. A microbial consortium able to degrade these VOCs was successfully enriched. A laboratory-scale SGB was established and operated for 210-d with an 8h cycle period and with shutdowns at weekends. Along this period, the SGB was exposed to organic loads (OL) between 6.5 and 2.3 x 10(2) g h(-1) m(-3). Most of the compounds were not detected at the outlet of the SGB. The highest total VOC removal efficiency (RE) (ca 99%) was observed when an OL of 1.6 x 10(2) g h(-1) m(-3) was fed to the SGB. The maximum total VOC elimination capacity (1.8 x 10(2) g h(-1) m(-3)) was achieved when the OL applied to the SGB was 2.3 x 10(2) g h(-1) m(-3). For all the operating conditions, the SGB showed high levels of degradation of toluene and butylacetate (RE approximately equal to 100%). This study also revealed that recirculation of the gaseous effluent improved the performance of the SGB. Overall, the SGB was shown to be robust, showing high performance after night and weekend shutdown periods.     

Evaluating a drinking-water waste by-product as a novel sorbent for arsenic

Arsenic (As) carcinogenicity to humans and other living organisms has promulgated extensive research on As treatment technologies with varying levels of success; generally, the most efficient methods come with a significantly higher cost burden and they usually perform better in removing As(V) than As(III) from solution. In the reported study, a novel sorbent, a waste by-product of the drinking-water treatment process, namely, drinking-water treatment residuals (WTRs) were evaluated for their ability to adsorb both As(V) and As(III). Drinking-WTRs can be obtained free-of-charge from drinking-water treatment plants, and they have been successfully used to reduce soluble phosphorus (P) concentrations in poorly P-sorbing soils. Phosphate and arsenate molecules have the same tetrahedral geometry, and they chemically behave in a similar manner. We hypothesized that the WTRs would be effective sorbents for both As(V) and As(III) species. Two WTRs (one Fe- and one Al-based) were used in batch experiments to optimize the maximum As(V) and As(III) sorption capacities, utilizing the effects of solid:solution ratios and reaction kinetics. Results showed that both WTRs exhibited high affinities for soluble As(V) and As(III), exhibiting Freundlich type adsorption with no obvious plateau after 2-d of reaction (15000 mg kg-1). The Al-WTR was highly effective in removing both As(V) and As(III), although As(III) removal was much slower. The Fe-WTR showed greater affinity for As(III) than for As(V) and reached As(III) sorption capacity levels similar to those obtained with the Al-WTR-As(V) system (15000 mg kg-1). Arsenic sorption kinetics were biphasic, similar to what has been observed with P sorption by the WTRs. Minimal (<3%) desorption of sorbed As(III) and As(V) was observed, using phosphate as the desorbing ligand. Dissolved Fe2+ concentrations measured during As(III) sorption were significantly correlated (r2=0.74, p<0.005) with the amount of As(III) sorbed by the Fe-WTR. Lack of correlation between Fe2+ in solution and sorbed As(V) (r2=0.2) suggests reductive dissolution of the Fe-WTR mediating As(III) sorption. Results show promising potential for the WTRs in irreversibly retaining As(V) and As(III) that should be further tested in field settings.     

Mechanisms of phosphorus solubilisation in a limed soil as a function of pH

Phosphorus (P) quantity-intensity relationships are central to the solubility and release of P from soil to water. Relationships between P extractable by 0.5 M NaHCO extractable P (Olsen P; quantity, Q) and P extractable by 0.01 M CaCl(2) (CaCl(2)-P; possible predictor of soil solution or drainage water P; intensity, I) are curvilinear: above a certain Olsen P concentration, CaCl(2)-P becomes much more soluble than when below it. Aluminium-, Fe- and Ca-P forms (extractable by Olsen's reagent) are thought to control P solubility. Thus, our objectives were to identify P forms in equilibrium with CaCl(2)-P via solubility equilibrium experiments, and the behaviour of CaCl(2)-P in relation to Al, Fe and Ca associated P, determined with 31P high power decoupling magic angle spinning nuclear magnetic resonance spectroscopy (31P HPDec/MAS NMR). Results indicated that two Q-I relationships occurred, one for soils above pH 5.8, and the other for soils below pH 5.8. Above pH 5.8, soils were saturated with respect to hydroxyapatite (Ca(5)(PO(4))(3)OH) and undersaturated with respect to beta-tricalcium phosphate (beta-Ca(3)(PO(4))(2)), while log ion-activity products showed that all soils and pHs were either saturated or in equilibrium with variscite (AlPO(4).2H(2)O) or its amorphous analogue. Using 31P HPDec/MAS NMR, Ca-P was best correlated with CaCl(2)-P in soils above pH 5.8, and with Al-P in soils below this pH. This study demonstrates the value of solid-state NMR in conjunction with wet chemical techniques for the study of labile P and P loss from pasture soils with a wide range of managements.     

Sampling Airborne Solids in a Duct Following a 90° Bend

Present standardized methods (ASME Power Test Code 27, Western Precipitation Bulletin 50, etc.) of stack sampling usually stress sampling under conditions of steady flow (no variation with time) in order to obtain data representative of the source emissions. On many occasions these standardized methods are applied when the velocity and/or the mass flow rate of pollutants do vary with time, thus impairing the accuracy of the sampling results. In addition, it is difficult to evaluate any inaccuracy of the sampling data. This paper classifies these two source variables into four categories and suggests basic sampling approaches for each type of source condition. Several standardized procedures are evaluated and classified according to the source conditions to which the procedure is applicable. The intent of this paper is to show the most accurate sampling approach for each source condition and thus serve as a guide when planning source sampling programs.     

Herbicide losses in runoff events from a field with a low slope: role of a vegetative filter strip

Herbicide runoff and the effects of a narrow vegetative filter strip (VFS) were studied on an arable field in the low-lying plains of the Veneto Region (north-east Italy). Cultivated plots were compared with and without a 6m wide VFS composed of trees, shrubs and grass. Natural and simulated runoff were monitored during 2000 and 2001. Herbicides applied on the field were: metolachlor (2184-2254 g ha(-1)), terbuthylazine (1000-1127 g ha(-1)) and isoproturon (1000 g ha(-1)). The VFS reduced both runoff depth (10.2-91.2%) and herbicide losses (85.7-97.9%) in the monitored rainfall events. Total herbicide loss with runoff was low (0.69-3.98 g ha(-1) without VFS, less than 0.27 g ha(-1) with VFS), but concentrations were sometimes very high, especially of terbuthylazine and isoproturon during the first events after treatment. In these events there was a high probability of exceeding the ecotoxicological endpoint for algae, but the VFS helped to reduce the potential risk. Two VFS effectiveness mechanisms were identified: (i) dilution, and (ii) a "sponge-like" effect, which temporarily trapped chemicals inside the VFS before releasing them.     

Alkylphenol oxidation with a laccase from a white-rot fungus: effects of culture induction and of ABTS used as a mediator

We investigated the potential of the laccase from the white-rot fungus Marasmius quercophilus to transform certain alkylphenols (p-nonylphenol, p-octylphenol and p-t-octylphenol). We tested the reactivity of this enzyme under different conditions: in liquid cultures and using the partially purified laccase with and without 2,2′-azino-bis-3-ehtylbenzothiazoline-6-sulfonicacid (ABTS) as a mediator. The percentage of p-t-octylphenol disappearance in liquid cultures was 69.0 ± 1.5% and 81 ± 5% after a 8-d or 15-d incubation, respectively, with p-nonylphenol, these percentages were 62 ± 4% and 91 ± 6% and with p-octylphenol 37 ± 3% and 65 ± 1% after a 15-d and a 21-d incubations, respectively. Induced pre-cultures were also used to inoculate the liquid cultures to enhance p-octylphenol transformation: the percentages of disappearance were 91.0 ± 0.5% and 97 ± 1% after a 8-d and a 15-d incubation, respectively. Mass spectrometry analysis showed that the products of oxidation of p-octylphenol were dimers with a mass of 411 m/z. Furthermore, we identified a purple compound (m/z 476) formed when ABTS was added to the reaction medium with the purified laccase. This result confirms that, in complex environments such as soils or litters where many molecules can interact with the enzyme substrate or the product of oxidation, laccase activities and those of other phenoloxidases should not be measured with ABTS.     

Analysis of waste management issues arising from a field study evaluating decontamination of a biological agent from a building

The Bio-response Operational Testing and Evaluation (BOTE) Project was a cross-government effort designed to operationally test and evaluate a response to a biological incident (release of Bacillus anthracis [Ba] spores, the causative agent for anthrax) from initial public health and law enforcement response through environmental remediation. The BOTE Project was designed to address site remediation after the release of a Ba simulant, Bacillus atrophaeus spp. globigii (Bg), within a facility, drawing upon recent advances in the biological sampling and decontamination areas. A key component of response to a biological contamination incident is the proper management of wastes and residues, which is woven throughout all response activities. Waste is generated throughout the response and includes items like sampling media packaging materials, discarded personal protective equipment, items removed from the facility either prior to or following decontamination, aqueous waste streams, and materials generated through the application of decontamination technologies. The amount of residual contaminating agent will impact the available disposal pathways and waste management costs. Waste management is an integral part of the decontamination process and should be included through “Pre-Incident” response planning. Overall, the pH-adjusted bleach decontamination process generated the most waste from the decontamination efforts, and fumigation with chlorine dioxide generated the least waste. A majority of the solid waste generated during pH-adjusted bleach decontamination was the nonporous surfaces that were removed, bagged, decontaminated ex situ, and treated as waste. The waste during the two fumigation rounds of the BOTE Project was associated mainly with sampling activities. Waste management activities may represent a significant contribution to the overall cost of the response/recovery operation. This paper addresses the waste management activities for the BOTE field test.Implications: Management of waste is a critical element of activities dealing with remediation of buildings and outdoor areas following a biological contamination incident. Waste management must be integrated into the overall remediation process, along with sampling, decontamination, resource management, and other important response elements, rather than being a stand-alone activity. The results presented in this paper will provide decision makers and emergency planners at the federal/state/tribal/local level information that can be used to integrate waste management into an overall systems approach to planning and response activities.     

Evaluation of a Gaussian and a Lagrangian model against a roadside data set,with emphasis on low wind speed conditions

The evaluation of the high percentiles of concentration distributions is required by most national air quality guidelines, as well as the EU directives. However, it is problematic to compute such high percentiles in stable, low wind speed or calm conditions. This study utilizes the results of a previous measurement campaign near a major road at Elimäki in southern Finland in 1995, a campaign specifically designed for model evaluation purposes. In this study, numerical simulations were performed with a Gaussian finite line source dispersion model CAR-FMI and a Lagrangian dispersion model GRAL, and model predictions were compared with the field measurements. In comparison with corresponding results presented previously in the literature, the agreement of measured and predicted data sets was good for both models considered, as measured using various statistical parameters. For instance, considering all NO_x data (N=587), the so-called index of agreement values varied from 0.76 to 0.87 and from 0.81 to 1.00 for the CAR-FMI and GRAL models, respectively. The CAR-FMI model tends to slightly overestimate the NO_x concentrations (fractional bias FB=+14%), while the GRAL model has a tendency to underestimate NO_x concentrations (FB=−16%). The GRAL model provides special treatment to account for enhanced horizontal dispersion in low wind speed conditions; while such adjustments have not been included in the CAR-FMI model. This type of Lagrangian model therefore predicts lower concentrations, in conditions of low wind speeds and stable stratification, in comparison with a standard Lagrangian model. In low wind speed conditions the meandering of the flow can be quite significant, leading to enhanced horizontal dispersion. We also analyzed the difference between the model predictions and measured data in terms of the wind speed and direction. The performance of the CAR-FMI model deteriorated as the wind direction approached a direction parallel to the road, and for the lowest wind speeds. However, the performance of the GRAL model varied less with wind speed and direction; the model simulated better the cases of low wind speed and those with the wind nearly parallel to the road.     

A description of a test plant for combustion on a pilot scale

A plant for combustion on a pilot scale is described.The plant is comprised of two shaft furnaces connected to a common afterburning chamber. Sawmill chips and LP-gas are used as supporting fuel. The plant is provided with equipment for continuous feeding-in of both solid and liquid wastes.The products of decomposition and residual concentrations resulting from combustion of the wastes are analysed with respect to different organic compounds. These analyses are made on ingoing product, slag, dust and fuel gases. In addition, temperature, transit time, gas composition (CO, CO₂, O₂), fuelgas flow and - in some cases - parameters such as total hydrocarbon and nitrogen oxides are investigated.     

The use of a high-FeO olivine rock as a redox buffer in a nuclear waste repository

Due to the higher stability of the spent nuclear fuel (mainly composed of UO2) under reducing conditions, and in order to enhance the retention/retardation of some key radionuclides, the olivine rock from the Lovasj?rvi intrusion has been proposed as a potential redox-active backfill-additive in deep high-level nuclear waste (HLNW) repositories. In this work, two different approaches have been undertaken in order to establish the redox buffer capacity of olivine rock: (1) The capacity of the rock to respond to changes in pH or pe has been demonstrated and the final (pH, pe) coordinates agree with the control exerted by the system Fe(II)/Fe(III). (2) The rate of consumption of oxygen has been determined at different pH values. These rates are higher than the ones reported in the literature for other solids, what would point to the possibility of using this rock as an additive to the backfill material in a HLNW.     

Fate of metolachlor under subirrigation in a sandy soil: a lysimeter study

A three-year field lysimeter study was conducted to investigate the role of subirrigation systems in reducing the risk of water pollution from metolachlor (2-chloro-N-(2-ethyl-6-methlphenyl)-N-(2-methoxy-1-methylethyl)ace tamide). Nine large PVC lysimeters, 1 m long x 0.45 m diameter, were packed with a sandy soil. Three water table management treatments, i.e. two subirrigation treatments with constant water table depths of 0.4 and 0.8 m, respectively, and a free drainage treatment in a completely randomized design with three replicates were used. Corn (Zea mays L.) was grown in each lysimeter, and at the beginning of summer of each year metolachlor was applied, at the locally recommended rate of 2.75 kg a.i./ha. Soil and water samples were collected at different time intervals after each natural or simulated rainfall event. Metolachlor was extracted from these samples and analyzed using Gas Chromatography. Results obtained in this three year study, (1993-1995), lead to the conclusion that metolachlor is quite mobile since it leached to a depth of 0.85 m below the soil surface quite early in the growing season. Metolachlor concentrations decreased with depth as well as with time. The shallower water table in the 0.4 m subirrigation treatment showed less residues in the soil solution than that of other treatments. However, a mass balance study, supported by an independent laboratory investigation, shows that water table management, statistically, has no significant effect on the reduction of metolachlor residues in sandy soils.     

Identification and quantification of a novel nitrate-reducing community in sediments of Suquía River basin along a nitrate gradient

We evaluated the molecular diversity of narG gene from Suquía River sediments to assess the impact of the nitrate concentration and water quality on the composition and structure of the nitrate-reducing bacterial community. To this aim, a library of one of the six monitoring stations corresponding to the highest nitrate concentration was constructed and 118 narG clones were screened. Nucleotide sequences were associated to narG gene from alpha-, beta-, delta-, gammaproteobacteria and Thermus thermophilus. Remarkably, 18% of clones contained narG genes with less than 69% similarity to narG sequences available in databases. Thus, indicating the presence of nitrate-reducing bacteria with novel narG genes, which were quantified by real-time PCR. Results show a variable number of narG copies, ranging from less than 1.0 × 10² to 5.0 × 10⁴ copies per ng of DNA, which were associated with a decreased water quality index monitored along the basin at different times.     

Co-processing of plastic waste in a cement kiln: a better option

Environmental Science and Pollution Research - This paper deals with the techniques to use plastic waste for co-processing in cement kiln for energy recovery. Plastics, a versatile material and...     

Heavy contamination of a subsurface aquifer and a stream by livestock wastewater in a stock farming area, Wonju, Korea

A survey of groundwater and stream water quality was undertaken in a stock farming area where livestock wastewater infiltrates into sandy unsaturated zones and saturated bedrock aquifers containing fractures. To determine the degree of contamination and track the effect of livestock wastewater on groundwater and stream water quality, the population of indicator bacteria (total coliforms, fecal coliforms, fecal streptococci, Staphylococcus spp., and sulfite-reducing clostridia) together with relevant physicochemical parameters were monitored along the wastewater flow-pathways over a 19-month period. The stream water was severely contaminated with livestock wastewater. Nearly all physicochemical and bacteriological parameters in the stream water were much greater than those in the groundwater. Nitrate-N concentrations ranged from 10.0 to 20.0 mg l(-1) in boreholes located downstream (site C) from the livestock waste disposal site, while those in the background borehole (W2) were below 1.0 mg l(-1). Densities of indicator bacteria in boreholes at site C were two or three orders of magnitude higher than those in W2 borehole. In boreholes located downstream from the livestock waste disposal site, the concentration of ammonium-N, nitrate-N, and pollution indicator bacteria increased as groundwater level rose due to infiltration of rainwater. In W2 borehole, however, physicochemical parameters and the number of pollution indicator bacteria had no correlation with the groundwater level. Collectively, these results suggest that the deep aquifers were heavily contaminated with infiltrated livestock wastewater, which consequently must be adequately treated to minimize groundwater pollution.     

On-road comparison of a portable emission measurement system with a mobile reference laboratory for a heavy-duty diesel vehicle

On-road comparisons were made between a mobile emissions laboratory (MEL) meeting federal standards and a portable emissions measurement system (PEMS). These comparisons were made over different conditions; including road grade, vibration, altitude, electric fields, and humidity with the PEMS mounted inside and outside of the tractor's cab. Brake-specific emissions were calculated to explore error differences between the MEL and PEMS during the Not-To-Exceed (NTE) engine operating zone. The PEMS brake-specific NOx (bsNOx) NTE emissions were biased high relative to the MEL and, in general, were about 8% of the 2007 in-use NTE NO_x standard of 2.68 g kW^?1 h^?1 (2.0 g hp^?1 h^?1). The bsCO₂ emissions for the PEMS were also consistently biased high relative to the MEL, with an average deviation of +4% ± 2%. NMHC and CO emissions were very low and typically less than 1% of the NTE threshold. This research was part of a comprehensive program to determine the “allowance” when PEMS are used for in-use compliance testing of heavy-duty diesel vehicles (HDDVs).     

Critical velocity and range of a fire-gas plume in a ventilated tunnel

To protect passengers, personnel and equipment in a tunnel fire, it is important to understand and predict the movements of the hot-gas plume. To estimate the range of a fire plume propagating under the ceiling, a model is presented, that depends on two important parameters, i.e. the energy release rate of the fire and the velocity of the ventilation flow. The theoretical results, concerning the upwind range of the plume, agree favourably with experimental data obtained from eight tunnel fire tests. The theoretical value of the critical ventilation velocity, required to arrest the upwind movement of the fire-gas, agrees well with the corresponding experimental results for a wide range of energy release rates. The influences of air entrainment, friction at the ceiling and the associated heat loss are analysed and the results discussed.     

Measuring ammonia concentration over a grassland near livestock facilities using a semiconductor ammonia sensor

We demonstrated the effectiveness of a semiconductor ammonia sensor capable of performing diachronic measurements; its characteristics were checked in the laboratory by means including comparison with standard gases. We found as a result that the ammonia sensor's readings increased with increasing water vapor pressure. We compared sensor readings with values obtained by chemical analysis of samples collected in situ and checked sensor reading accuracy. Ammonia concentration was determined by combining ammonia sensor readings with measured values for water vapor pressure. In situ conditions were ammonia concentration of under 100 ppbv and water vapor pressure of 4–16 hPa. There was a good correlation with the concentration of samples trapped with boric acid and analyzed by indophenol colorimetry. We discerned a relationship between ammonia concentration and local meteorological conditions such as wind direction and speed. The estimated error of the ammonia sensor's measurements was ±9.7 ppbv when ammonia concentration as measured by acid sampling and colorimetry was regarded as correct. This demonstrated that it is possible to detect in situ fluctuations in low ammonia concentrations of about 10 ppbv, which was the background concentration in farming areas. We have shown a monitoring method for ammonia in situ that is both easy to operate and low-cost.