Butyltin distribution in a sediment core from Arcachon harbour (France)

The concentrations of butyltin compounds in water, intertidal sediments and in a sediment core have been measured in the harbour of Arcachon (France) in order to assess the effectiveness of government legislative actions on the use of tributylin (TBT) in marine antifouling paints. The results revealed the occurrence of an increasing TBT gradient from the bottom to the top of the core with a maximum at 15 cm depth, and a slight decrease within the upper 15 cm. It is shown that the TBT levels are still very high in this area and that this compound is not rapidly degraded in sediment as was previously assumed. This leads to the conclusion that even if the regulations have been respected, contamination from resuspended sediments is still likely.     

Immunotoxicity in ascidians: antifouling compounds alternative to organotins: III--the case of copper(I) and Irgarol 1051

After the widespread ban of TBT, due to its severe impact on coastal biocoenoses, mainly related to its immunosuppressive effects on both invertebrates and vertebrates, alternative biocides such as Cu(I) salts and the triazine Irgarol 1051, the latter previously used in agriculture as a herbicide, have been massively introduced in combined formulations for antifouling paints against a wide spectrum of fouling organisms. Using short-term (60 min) haemocyte cultures of the colonial ascidian Botryllus schlosseri exposed to various sublethal concentrations of copper(I) chloride (LC₅₀ = 281 μM, i.e., 17.8 mg Cu L⁻¹) and Irgarol 1051 (LC₅₀ > 500 μM, i.e., >127 mg L⁻¹), we evaluated their immunotoxic effects through a series of cytochemical assays previously used for organotin compounds. Both compounds can induce dose-dependent immunosuppression, acting on different cellular targets and altering many activities of immunocytes but, unlike TBT, did not have significant effects on cell morphology. Generally, Cu(I) appeared to be more toxic than Irgarol 1051: it significantly (p < 0.05) inhibited yeast phagocytosis at 0.1 μM (∼10 μg L⁻¹), and affected calcium homeostasis and mitochondrial cytochrome-c oxidase activity at 0.01 μM (∼1 μg L⁻¹). Both substances were able to change membrane permeability, induce apoptosis from concentrations of 0.1 μM (∼10 μg L⁻¹) and 200 μM (∼50 mg L⁻¹) for Cu(I) and Irgarol 1051, respectively, and alter the activity of hydrolases. Both Cu(I) and Irgarol 1051 inhibited the activity of phenoloxidase, but did not show any interactive effect when co-present in the exposure medium, suggesting different mechanisms of action.     

Comparative environmental assessment of biocides used in antifouling paints

In response to increasing scientific evidence on the toxicity and persistence of organotin residues from antifouling paints in the aquatic environment, the use of triorganotin antifouling products was banned on boats of less than 25 m length in many countries during 1987. Alternatives to tributyltin (TBT) paint are mainly copper based coatings containing organic booster biocides to improve the efficacy of the formulation, and have been utilised on small boats for the last 10 years. With policies encouraging a total ban on TBT, it is expected that these biocides will be used to a greater extent in the future. Limited data and information are available on the environmental occurrence, fate, toxicity, and persistence of these biocides, and thus any decisions on policies regulating antifoulants cannot be fully informed. In this study, a multicriteria comparison of alternative biocides, based on a general assessment of available information in the literature, provided support for the use of the precautionary principle with respect to policies on antifouling products. This assessment was validated by a more detailed comparison of four selected biocides and TBT. Results indicate that TCMS pyridine and TCMTB demonstrate environmental characteristics similar to TBT and thus detail risk assessments are needed before their use is permitted. The widespread use of the other biocides should be allowed only after research to fill the gaps in knowledge with respect to their toxicity and persistence in aquatic environments.     

Review of measured concentrations of triphenyltin compounds in marine ecosystems and meta-analysis of their risks to humans and the environment

The state of scientific knowledge regarding analytical methods, environmental fate, ecotoxicity and ecological risk of triphenyltin (TPT) compounds in marine ecosystems as well as their exposure and health hazard to humans was reviewed. Since the 1960s, TPT compounds have been commonly applied as biocides for diverse industrial and agricultural purposes. For instance, they are used as active ingredients in antifouling systems on marine vessels and mariculture facilities, and as fungicides in agriculture. Due to their intensive use, contamination of coastal waters by TPT and its products of transformation has become a worldwide problem. The proportion of quantified TPT to total phenyltin compounds in the marine environment provides evidence that TPT is photodegradable in water and sediment but resistant to biotransformation. Concentrations of TPT in marine biota are consistently greater than concentrations in water and sediment, which implies potential of TPT to bioaccumulate. TPT is toxic to both marine plants and animals. The predicted no effect concentration (PNEC) for TPT, as determined by use of the species sensitivity distribution approach, is 0.64 ng L⁻¹. In some parts of the world, concentrations of TPT in seawater exceed the PNEC, indicating that TPT can pose risks to marine life. Although there is negligible risk of TPT to average human consumers, TPT has been detected in blood of Finnish people and the concentration was greater in fishermen who ate more seafood. It is, therefore, advocated to initiate regular monitoring of TPT in blood and breast milk of populations that consume greater amounts of seafood.     

Aerobic biodegradation of organotin compounds in activated sludge batch reactors

The biodegradation behavior of four organotin (OT) compounds, namely tributyltin (TBT), dibutyltin (DBT), monobutyltin (MBT) and triphenyltin (TPhT), was studied in lab-scale activated sludge batch reactors. The activated sludge was spiked with the OT compounds at a level of 100 microg l(-1) as Sn. Determination of the OT compounds by GC-FPD after ethylation in the dissolved and particulate phase revealed that 24 h after the start of the experiments, almost the total of OT compounds has been removed from the dissolved phase and is associated with the suspended solids. Calculation of mass balance in batch reactors showed that OT compounds biodegradation was performed via a sequential dealkylation process. Removals due to biodegradation were differentiated according to the parent compound. In experiments with non-acclimatized biomass, a percentage of 27.1, 8.3, 73.8 and 51.3 was still present as TBT, DBT, MBT and TPhT, respectively, at the end of the experiment (18th day). Half-lives (t1/2) of 10.2 and 5.1 days were calculated for TBT and DBT, respectively, whereas apparent t1/2 values could not be determined for MBT and TPhT (t1/2>18 days). The capacity of activated sludge to biodegrade OT compounds in the absence of supplemental substrate indicated that these compounds can be metabolized as single sources of carbon and energy in activated sludge systems. Excluding TBT, the presence of low concentrations of supplemental substrate did not affect the biodegradation potential of activated sludge. The acclimatization of biomass on OT compounds enhanced significantly biodegradation, resulting in significant decreases of half-lives of OT compounds. As a result in the presence of acclimatized biomass, half-lives of 1.4, 3.6, 9.8 and 5.0 days were calculated for TBT, DBT, MBT and TPhT, respectively.     

Inputs of antifouling paint-derived dichlorodiphenyltrichloroethanes (DDTs) to a typical mariculture zone (South China): potential impact on aquafarming environment

Existing evidence indicated that dichlorodiphenyltrichloroethane (DDT)-containing antifouling paints were an important source of DDT residues to mariculture zones. However, the magnitude of the impact on aquafarming environment has remained largely unknown. In the present study, the concentrations of DDT and its metabolites (designated as DDXs) were determined in harbor sediment and antifouling paint samples collected from a typical mariculture zone in South China. Compositional and concentration correlation analyses implicated the DDT-containing antifouling paints for fishing boat maintenance as an important source of DDT in the mariculture zone. The annual emission of DDXs to the study region was estimated at 0.58 tons/yr. Furthermore, a comparison of the expected DDT loadings in pelagic fish and field measurements indicated that fish feed especially trash fish was a major source of DDTs in the fish body. Nevertheless, the use of DDT-containing antifouling paints should be limited to prevent further deterioration in aquafarming environment.     

Bioremediation of tributyltin contaminated sediment: degradation enhancement and improvement of bioavailability to promote treatment processes

Bioremediation of tributyltin (TBT) contaminated sediment was studied and degradation enhancement and improvement of bioavailability were also investigated. In TBT spiked sediment, the half-life of TBT in the control sample, representing natural attenuation, was 578 d indicating its persistence. In the stimulated sample (pH 7.5, aeration and incubated at 28 °C), the half-life was significantly reduced to 11 d. Further stimulation by nutrient addition (succinate, glycerol and l-arginine) or inoculation with Enterobacter cloacae (∼10⁷ viable cells g⁻¹ of sediment) resulted in half-life reduction to 9 and 10 d, respectively. In non-spiked sediment, the indigenous microorganisms were able to degrade aged TBT, but the extended period of contamination decreased the degradation efficiency. To improve bioavailability, addition of surfactant, adjustment of salinity and sonication were studied. The highest percentage solubilisation of TBT in water was obtained by adjusting salinity to 20 psu, which increased the solubility of TBT from 13% to 33%. Half-lives after bioavailability was improved were 5, 4 and 4 d for stimulation, stimulation w/nutrient addition and stimulation w/inoculation, respectively. However, natural attenuation in the control sample was not enhanced. The results show that providing suitable conditions is important in enhancing TBT biodegradation, and bioavailability improvement additionally increased the rate and degraded amount of TBT. Unfortunately, nutrient addition and inoculation of the degrader did not enhance the degradation appreciably.     

Bioassays and selected chemical analysis of biocide-free antifouling coatings

Over the years several types of biocide-free antifouling paints have entered the market. The prohibition of biocidal antifouling paints in special areas of some European countries such as Sweden, Denmark and Germany has favoured the introduction of these paints to the market.

Several types of biocide-free antifouling paints were subjected to bioassays and selected chemical analysis of leachate and incorporated substances. Both non-eroding coatings (silicones, fibre coats, epoxies, polyurethane, polyvinyl) and eroding coatings (SPCs, ablative) were tested to exclude the presence of active biocides and dangerous compounds. The paints were subjected to the luminescent bacteria test and the cypris larvae settlement assay, the latter delivering information on toxicity as well as on efficacy.

The following chemical analyses of selected compounds of dry-film were performed:

• leaching-rate of organotin compounds from silicones and of nonylphenol and bisphenol A from epoxy and vinyl based coatings,

• concentration and leaching rate of selected organic compounds in polyurethane,

• concentration of heavy metals in eroding coatings.

The results of the bioassays indicated that none of the coatings analysed contained leachable biocides. Nevertheless, some products contained or leached dangerous compounds. The analyses revealed leaching of nonylphenol (up to 74.7 ng/cm²/d after 48 h) and bisphenol A (up to 2.77 ng/cm²/d after 24 h) from epoxy resins used as substitutes for antifouling paints. The heavy metal, zinc, was measured in dry paint film in quantities up to 576 000 ppm in erodable coatings, not incorporated as a biocide but to control the rate of erosion. Values for TBT in silicone elutriates were mostly below the detection limit of 0.005 mg/kg. Values for DBT ranged between <0.005 and 6.28 mg/kg, deriving from catalysts used as curing agents. Some biocide-free paints contained leachable, toxic and dangerous compounds in the dry film, some of which may act as substitutes for biocides or are incorporated as plasticizers or catalysts. Implications to environmental requirements and legislation are discussed.     

Influence of releases of I-129 from reprocessing plants on the marine environment of the North Adriatic Sea

Compared to the pre-nuclear era, large amounts of ¹²⁹I have been released to the marine environment, especially as liquid and gaseous discharges from two European reprocessing plants located at Sellafield and La Hague. Their liquid discharges influence Northern Europe and most research was conducted in the area of the North Atlantic Ocean and the Baltic Sea. In this article data on ¹²⁹I content and ¹²⁹I/¹²⁷I ratios observed in the North Adriatic Sea, which is a rather enclosed basin of the Mediterranean Sea, are presented. To the best of our knowledge no data on ¹²⁹I in the Mediterranean Sea have previously been reported. As this area is isolated from direct liquid discharges, the main transport pathway is probably gaseous releases from reprocessing plants. Surface sea water, the marine alga Fucus virsoides, an iodine accumulator, and the Mediterranean mussel Mytilus galloprovincialis collected in 2009 and 2010, and marine sediment collected in 2005 and 2009 were analysed. The ¹²⁹I/¹²⁷I isotopic ratios observed were in the range from 0.8 to 3.0 × 10⁻⁰⁸ for seawater, from 0.06 to 0.35 × 10⁻⁰⁸ for marine sediment, from 0.05 to 0.10 × 10⁻⁰⁸ for F. virsoides and from 0.3 to 0.9 × 10⁻⁰⁸ for M. galloprovincialis.     

Imposex occurrence in marine whelks at a military facility in the high Arctic

Imposex was found in the Arctic whelk Buccinum finmarkianum at several marine stations off Thule Air Base, an US military facility in Northwest Greenland. This indicates a widespread contamination with the antifouling agents, tributyltin (TBT) or triphenyltin (TPhT) in the area, but such contamination was not supported by the organotin analyses in sediments, whelks and clams, which in general was below the analytical detection limit. Organotin concentrations above the detection limit were found only at one station close to a quay, where the highest frequency of imposex also occurred. This suggests that imposex in B. finmarkianum is a biomarker of TBT more sensitive than the detection limits, which the analytical chemistry could achieve in this study.     

Toxicity and metabolism of copper pyrithione and its degradation product, 2,2'-dipyridyldisulfide in a marine polychaete

We conducted acute toxicity tests and sediment toxicity tests for copper pyrithione (CuPT) and a metal pyrithione degradation product, 2,2′-dipyridyldisulfide [(PS)₂], using a marine polychaete Perinereis nuntia. The acute toxicity tests yielded 14-d LC₅₀ concentrations for CuPT and (PS)₂ of 0.06 mg L⁻¹ and 7.9 mg L⁻¹, respectively. Sediment toxicity tests resulted in 14-d LC₅₀ concentrations for CuPT and (PS)₂ of 1.1 mg kg⁻¹ dry wt. and 14 mg kg⁻¹ dry wt., respectively. In addition to mortality, sediment avoidance behavior and decreases in animal growth rate were observed; growth rate was the most susceptible endpoint in the sediment toxicity tests of both toxicants. Thus, we propose lowest observed effect concentrations of 0.3 mg kg⁻¹ dry wt. and 0.2 mg kg⁻¹ dry wt. for CuPT and (PS)₂, respectively, and no observed effect concentrations of 0.1 mg kg⁻¹ dry wt. for both CuPT and (PS)₂. The difference in the toxicity values between CuPT and (PS)₂ observed in the acute toxicity test was greater than the difference in these values in the sediment toxicity test, and we attribute this to (PS)₂ being more hydrophilic than CuPT. In addition to the toxicity tests, we analyzed conjugation activity of several polychaete enzymes to the toxicants and marked activity of palmitoyl coenzyme-A:biocides acyltransferase and UDP-glucuronosyl transferase was observed.     

Tributyltin chloride results in dorsal curvature in embryo development of Sebastiscus marmoratus via apoptosis pathway

Tributyltin (TBT) is a ubiquitous marine environmental contaminant characterized primarily by its reproductive toxicity. However, the embryotoxicity of TBT has not been extensively described, especially in fishes. The aim of this study was to investigate the developmental toxicity of waterborne TBT at environmental levels (0, 0.1, 1, and 10 ng L⁻¹ as Sn) on Sebastiscus marmoratus embryos. Our study showed that TBT reduced the hatchability and caused apparent morphological abnormalities including dorsal curvature, severely twisted tails and pericardial edema. In addition, localized apoptosis was found in the tail regions of embryos after TBT exposure. The study provided a possible mechanistic link between apoptosis and TBT-induced twisted tails abnormality. TBT exposure induced retinoid X receptor α expression in S. marmoratus embryos at the 0.1 and 1 ng L⁻¹ group, which would be responsible for the increasing apoptotic cells induced by TBT. The results of the present study have widespread implications for environmental ecological assessment, management and the etiology of developmental defects.     

Butyltins in water, biofilm, animals and sediments of the west coast of India

Biofilm, fish, oyster, mussel, clam, surface seawater, suspended particulate matter (SPM), and sediment samples were collected from marine and/or estuarine waters of the west coast of India. These samples were analysed for butyltin derivatives such as dibutyltin (DBT) and tributyltin (TBT). The concentrations DBT plus TBT varied between 2.4 and 8.3, 163 and 363 ng/l, 5 and 2853 ng/g dry wt in the SPM, seawater and sediment samples, respectively, of the Marmugao harbour. The values of DBT plus TBT ranged between 0.60 and 29, 123 and 242 ng/l and 1.4 and 65 ng/g dry wt in SPM, water and sediment samples, respectively, collected from the Mandovi estuary. In the Dona Paula Bay the DBT plus TBT varied from 10 to 89 ng/l in surface seawater, and TBT from 10 to 513 ng/g in biofilm samples. For the coastal sediment samples the concentration of DBT plus TBT ranged between 36 and 133 ng/g dry wt of sediment. For the animal samples the DBT plus TBT ranged between 58 and 825 ng/g dry wt of the tissue. Mussel tissues contained the highest amount of DBT plus TBT (825 ng/g dry wt tissue), whereas highest TBT concentration was recorded in the oyster (732 ng/g dry wt). TBT was generally the most abundant butyltin compound in most of the samples suggesting fresh inputs and/or less degradation of TBT. A wide range of the observed butyltin concentrations suggests the presence of localized areas of contamination. Leaching of tributyltin-containing antifouling paints from the ocean going ships, fishing and recreational boats, barges, and the inputs of TBT from the Goa shipyard and dry dock facility situated in the harbour are the probable sources of the DBT and TBT in the samples of the west coast of India. Higher levels of TBT were observed in biofilm relative to that in the surrounding seawater. When fed on TBT contaminated biofilm of the diatom Navicula subinflata, butyltin concentrations in the clam Paphia malabarica increased over the period of feeding suggesting the importance of biofilm in the transfer of butyltins to higher group of organisms.     

Coral skeletal tin and copper concentrations at Pohnpei, Micronesia: possible index for marine pollution by toxic anti-biofouling paints

We present 40 year-long skeletal chronologies of tin (Sn) and copper (Cu) from an annually-banded coral (Porites sp.) collected from Pohnpei Island, Micronesia (western equatorial Pacific). Both the elements are present in antifouling marine paints and are released inadvertently into ambient seawater. Especially, Sn has often been used in the form of tributyltin (TBT). Based on a stepwise pretreatment examination, Sn and Cu both inside and outside the aragonite lattice of the coral skeleton show a potential for providing marine pollution indicators. High values of extra-skeletal Cu/Ca and Sn/Ca atomic ratios were found between late 1960s and late 1980s during a period of active use of TBT-based antifouling paints worldwide. However, a significant decrease in both the ratios in the beginning of 1990s can be attributed to regulation of the use of TBT on cargo ships by countries such as the USA, Japan and Australia.     

Environmental mutagenicity and toxicity caused by sodium metabisulfite in sea shrimp harvesting in Piauí, Brazil

Sodium metabisulfite is used in marine shrimp harvesting to prevent the occurrence of black spots. Shrimps are soaked in a sodium metabisulfite solution in ice, which is disposed of in sewages that run into marine canals, creating an environmental hazard. This study evaluates the toxicity and mutagenicity caused by sodium metabisulfite in sea waters and sediments collected in a shrimp farm in Cajueiro da Praia (Luis Correia), state of Piauí, Brazil, using the Allium cepa assay. Water and sediment samples were collected in the dry and in the rainy seasons, in three sites: upstream the shrimp farm (Site 1), at the point sodium metabisulfite is discharged (Site 2), and 100 m downstream the farm (Site 3). Three sample dilutions were used (50%, 25% and 10%) for all samples. A negative control (well water) and a positive control (copper sulfate 0.0006 mg mL⁻¹) were used in each experiment. At the end of the 72-h exposure period, onion roots were measured and removed. Mutagenicity analysis included the determination of mitotic index, chromosomal aberrations and the detection of micronuclei; analysis of root size and mitotic index were used as an index of toxicity. The A. cepa assay revealed that the water and sediments samples collected in the Piauí coast contaminated with sodium metabisulfite induce toxicity. The results demonstrate that the assay may be used as a regular tool in the analysis of water parameters in shrimp farms in the coast of Piauí state, and in strategies to preserve the region’s marine ecosystem.     

Multidimensional risk analysis of antifouling biocides

In order to improve the orientation about the long-term sustainability of the use of the antifouling biocides tributyltin (TBT), copper, Irgarol® 1051, Sea-Nine? 211 and zinc pyrithione, used for the protection of fouling in sea-going ships, the risks posed to the marine biosphere due to their use are evaluated. The newly presented method of risk analysis uses release rate, spatiotemporal range, bioaccumulation, bioactivity and uncertainty as 5 dimensions of ecotoxicological risk. For each dimension, a scoring procedure is briefly described. The resulting risk profiles of the antifouling biocides show characteristics of the different substances, but also indicate where further information is required. Application of the method is proposed as a decision support in the integrated development of products, informed purchasing and for regulatory purposes.     

Imposex in the commercial snail Bolinus brandaris in the northwestern Mediterranean

A survey of the degree of imposex in populations of the commercial muricid Bolinus brandaris (L.) was carried out at six locations along the Catalan Coast (NW Mediterranean). Imposex was found to be a widespread phenomenon; the occurrence of a penis was observed in all females studied with the exception of those from St. Carles (South of Catalunya) where only 37% were affected. Other indices such as Relative Penis Length (RPL) and Vas Deferens Sequence (VDS) were applied; RPL varied from 4.5% in St. Carles--the least affected area--to 29.8% in the vicinity of Barcelona; similar results were obtained for VDS. Tissue organotin residues ranged from 6 to 140 ng g(-1) w.w. as Sn. Despite legislation restricting the use of tributyltin (TBT) in antifouling paints, this paper evidences the occurrence of organotin pollution far from the source, with levels of both TBT and triphenyltin (TPhT) high enough to cause environmental concern.     

Analytical methods for the determination of 9 antifouling paint booster biocides in estuarine water samples

Analytical procedures for the determination of nine organic booster biocides which are currently licensed for use in marine antifouling paints, and are thought likely to occur at concentrations in the ng 1⁻¹ range in estuarine water samples, are reviewed. A robust multiresidue method for the determination of four compounds (chlorothalonil, dichlofluanid, diuron and Irgarol 1051) is suggested. A route for the development of a method for the analysis of zinc pyrithione is outlined, based on an extraction method and subsequent derivatisation prior to determination by HPLC with fluorescence detection. Methodology for Zineb, Kathon 5287, TCMS pyridine and TCMTB is less clearly defined.     

Survey for the occurrence of antifouling paint booster biocides in the aquatic environment of Greece

Since the restriction imposed by European Union regulations on the use of TBT-based antifouling paints on boats below 25 m in length, new terms have been introduced in the 'small boat' market. Replacement products are generally based on copper metal oxides and organic biocides. Several studies have demonstrated the presence of these biocides in European ports and marinas of Spain, France, Germany and the United Kingdom. An extended survey of the antifouling biocides chlorothalonil, dichlofluanid, irgarol 1051 and sea-nine 211 was carried out in Greek ports and marinas of high boating activities from October 1999 to September 2000. The sampling sites were: Piraeus, Elefsina, Thessaloniki, Patras, Chalkida, Igoumenitsa, and Preveza (Aktio). The extraction of these compounds from the seawater samples was performed off-line with C18 solid phase extraction (SPE) disks while the determination was carried out with gas chromatography coupled to electron capture (ECD), thermionic (FTD) and mass spectroscopy (MS) detectors. The concentration levels of biocides were higher during the period from April to October. This seasonal impact depends on the application time of antifouling paints and mimic trends in the seasonal distribution of biocides in other European sites.     

Freshwater Ulva (Chlorophyta) as a bioaccumulator of selected heavy metals (Cd, Ni and Pb) and alkaline earth metals (Ca and Mg)

We analyzed the ability of freshwater taxa of the genus Ulva (Ulvaceae, Chlorophyta) to serve as bioindicators of metal in lakes and rivers. Changes in heavy metal (Ni, Cd and Pb) and alkaline earth metal (Ca and Mg) concentrations in freshwater Ulva thalli were investigated during the period from June to August 2010. The study was conducted in two ecosystems in Western Poland, the Malta lake (10 sites) and the Nielba river (six sites). Three components were collected for each sample, including water, sediment and Ulva thalli. The average concentrations of metals in the water sample and in the macroalgae decreased in the following order: Ca > Mg > Ni > Pb > Cd. The sediment revealed a slightly altered order: Ca > Mg > Pb > Ni > Cd. Ca and Mg were found at the highest concentrations in thalli due to the presence of carbonate on its surface. Among the examined heavy metals in thalli, Ni was in the highest concentration, and Cd found in the lowest concentration. There were statistically significant correlations between the levels of metals in macroalgae, water and sediment. Freshwater populations of Ulva exhibited a greater efficiency to bioaccumulate nickel as compared to species derived from marine ecosystems.