冷轧废水污泥铬回收后残渣的脱硫研究

为了最大限度地对污泥进行回收利用,将钢厂冷轧废水处理后污泥铬回收后的残渣制备成脱硫剂,并研究其脱硫特性.结果表明,加入碳酸钠在高温下有氧焙烧,冷轧废水处理后污泥铬回收后的残渣中Fe2O3约为45%(质量分数),Fe2ZnO4约为6%(质量分数);将该残渣与粘结剂、制孔剂和结构剂按一定配比混合制备脱硫剂,在空速为400～500 h-1和不持续补充水分的实验条件下,与含3 500 mg/m3左右H2S的模拟气接触时,一次脱硫实验表明其穿透硫容在5%以上.     

不同载体负载氧化铜常温脱除H_2S

通过沉淀法制备了纯CuO和3种CuO/SiO_2、CuO/ZrO_2和CuO/Al_2O_3负载型脱硫剂。利用固定床反应器进行了硫化氢吸附测试,并采用XRD、SEM、TEM、H2-TPR、比表面积和孔结构等表征技术对脱硫剂的结构进行了分析。结果表明,载体的存在明显提高了纯CuO脱硫剂的利用率和脱硫活性,其中以SiO_2为载体制备的脱硫剂性能最佳,硫容达14.3%,是纯CuO硫容的2.6倍;分析认为SiO_2抑制了CuO晶粒的形成,使得CuO/SiO_2脱硫剂的比表面积明显增大,活性组分的结晶度较差,因而有利于脱硫反应的进行。     

改性凹凸棒粘土脱硫剂脱除SO2

采用单因素法,在传统搅拌混合下,研究了煅烧温度、煅烧时间、酸碱浸渍等对改性凹凸棒粘土脱硫剂穿透硫容与最大硫容的影响.然后在超声波混合作用下,采用正交实验确定了超声时间、超声温度以及活性组分(CaO)、促进剂(V2O5)的复配比例.结果表明:(1)甘肃临泽凹凸棒粘土富Al、Mg、Fe,且其比表面积较大.(2)改性凹凸棒粘土脱硫剂最佳制备条件:煅烧温度300℃;煅烧时间2.0 h;酸碱浸渍最佳pH9～10;混合采用超声波,超声时间30 min;超声温度40℃;CaO质量分数30%;V2O5质量分数5%.采用在最佳条件下制备的改性凹凸棒粘土脱硫剂进行脱除SO2实验,其最大硫容为38.16%.(3)改性凹凸棒粘土脱除SO2的性能比工业Fe2O3脱硫剂强.(4)X射线衍射分析表明,改性凹凸棒粘土脱硫剂脱除SO2后,将SO2转变为SO2-4,从而达到完全脱除SO2的目的,这与红外光谱分析的结果一致.     

粗媒体颗粒流化床半干法烟气脱硫

开发了粗媒体颗粒流化床半干法烟气脱硫技术.在流化床内加入惰性粗媒体颗粒,改善脱硫剂与烟气的接触,延长脱硫剂在床内的停留时间,促进脱硫反应进行,提高脱硫效率和脱硫剂利用率.以工业用石灰石为脱硫剂,实验研究了粗媒体颗粒的加入量及其他操作条件对此过程脱硫效率的影响.结果表明:随着粗媒体颗粒粒径减小及床内加入量增加,烟气脱硫效率提高;随着Ca/S增大、饱和接近度降低、空速及脱硫剂颗粒粒径减小,脱硫效率提高.当粗媒体颗粒的静止床高为122 mm,饱和接近度为15～18℃、空速为2850 h-1、钙硫比为1.0～1.1、脱硫剂粒径为64μm时,脱硫效率可达90%以上.     

酸碱改性对氧化铁脱硫剂脱硫性能影响的研究

通过酸碱改性制备了酸式和碱式2种不同表面性质的常温氧化铁脱硫剂,并采用FT-IR技术对其表面酸碱性质和净化硫化氢废气活性进行了研究.结果表明,表面酸碱件质不同的脱硫剂其脱硫反应行为也不同,在脱硫过程中硫化氢氧化生成的硫酸及亚硫酸会影响脱硫剂的表面酸碱性质,造成酸式脱硫剂的表面酸性更强,从而抑制了硫化氢分子在酸式脱硫剂表...     

反应条件对Cu/Ni/Fe类水滑石去除CS_2的影响

采用共沉淀法合成Cu/Ni/Fe三元类水滑石衍生氧化物作为催化剂,从反应温度、空速、进口浓度、氧含量和相对湿度等方面考察了该催化剂对二硫化碳(CS_2)催化水解性能的影响以及不同反应条件对催化剂硫容的影响。实验结果表明:当反应温度为60~70℃、反应空速为2 000~4 000 h~(-1)、进口浓度为100~340 mg·m~(-3)、相对湿度为0.47%~0.67%时,该催化剂具有较高的脱硫效果和工作硫容;O_2含量的增加促进了水解产物H_2S氧化为硫酸盐,进而堵塞催化剂的碱性位,加快了催化剂中毒失活;H_2O和CS_2之间存在竞争吸附,一定含量的水蒸气有利于CS_2的水解反应,而过高含量的水会阻碍水解反应的进行,导致催化剂失活。     

白云石的硫化氢高温脱除性能研究

用天然白云石制备了半焙烧白云石和全焙烧白云石，并在固定床上对这些白云石进行硫化氢的高温脱除性能研究，同时考察了反应温度、空速、粒子粒径对白云石脱硫性能的影响。用X射线衍射（XRD）、热重分析（TG）和气体吸附等测试手段，对脱硫剂的物相组成、结构、比表面积和孔容进行了表征。结果表明，白云石是一种很好的吸硫剂。在同样条件下，3种白云石中半焙烧白云石具有最好的脱硫效果；而对于同一种白云石，反应条件的差异也会导致其脱硫效果的变化。白云石的脱硫性能与其微观结构有密切关系。     

白云石的硫化氢高温脱除性能研究

用天然白云石制备了半焙烧白云石和全焙烧白云石,并在固定床上对这些白云石进行硫化氢的高温脱除性栽能研究,同时考察了反应温度、空速、粒子粒径对白云石脱硫性能的影响.用X射线衍射(XRD)、热重分析(TG)和气体吸附等测试手段,对脱硫剂的物相组成、结构、比表面积和孔容进行了表征.结果表明,白云石是一种很好的吸硫剂.在同样条件下,3种白云石中半焙烧白云石具有最好的脱硫效果;而对于同一种白云石,反应条件的差异也会导致其脱硫效果的变化.白云石的脱硫性能与其微观结构有密切关系.     

全硅β分子筛催化氧化NO性能研究

针对NO氧化催化剂抗水汽性差、活性温度高等问题,本研究采用疏水型全硅β分子筛为催化剂,在NO进口浓度为0.05%(体积分数)、O2浓度为20.7%(体积分数)条件下,考察了反应温度(20~60℃)、相对湿度(0%~100%)、空速(360 h-1~20 000 h-1)等因素对NO催化氧化的影响。研究结果表明,随着反应温度升高,干气和湿气下NO氧化率都下降,低温有利于NO氧化;在20℃,空速为20 000 h-1条件下,相对湿度从0%增大到100%时,NO氧化率从49%下降到34%。反应温度升高会抑制水汽对NO氧化的影响。240 h催化剂稳定性实验结果表明,在30℃,NO进口浓度为0.05%,空速为7 200 h-1时,干气和饱和水汽下的NO氧化率分别能稳定地维持在67%和56%水平,说明全硅β分子筛即使在饱和水汽下也具有良好的稳定性及抗水汽性。     

粗媒体颗粒流化床半干法烟气脱硫

开发了粗媒体颗粒流化床半干法烟气脱硫技术。在流化床内加入惰性粗媒体颗粒，改善脱硫剂与烟气的接触。延长脱硫剂在床内的停留时间，促进脱硫反应进行，提高脱硫效率和脱硫剂利用率。以工业用石灰石为脱硫剂，实验研究了粗媒体颗粒的加入量及其他操作条件对此过程脱硫效率的影响。结果表明：随着粗媒体颗粒粒径减小及床内加入量增加，烟气脱硫效率提高；随着Ca／S增大、饱和接近度降低、空速及脱硫剂颗粒粒径减小，脱硫效率提高。当粗媒体颗粒的静止床高为122mm，饱和接近度为15～18℃、空速为2850h^-1、钙硫比为1．0—1．1、脱硫剂粒径为64μm时，脱硫效率可达90％以上。     

Catalytic oxidation for air pollution control

Bench-scale experiments have been conducted to evaluate a series of titania-supported Pt-Pd (as oxides) catalysts in the presence and absence of MoO₃ and Fe₂O₃ additives for their effectiveness in the complete catalytic oxidation of volatile organic compounds (VOCs) in air likely to be found in waste gases. Under oxidizing conditions, all of the catalysts promoted the complete oxidation of VOCs to CO₂ and H₂O. 99 % Conversion was achieved with a C₂H₄-C₂H₆ gas mixture in air at temperatures between about 160–450 °C and at a space velocity of 20,000 h^?1. Oxidation activity for the titania supported catalysts were found to decrease in the order Pt-Pd-Mo-Fe > Pt-Pd-Mo > Pt-Pd-Fe > Pt-Pd. However, the addition of MoO₃ and Fe₂O₃ increase the catalyst activity and reduce the reaction temperature for the complete destruction. Ageing was also performed in order to study the stability of the most active catalyst. Pt-Pd-Mo-Fe (as oxides) on titania catalyst is effective in oxidizing a wide range of volatile organic compounds at relatively low temperatures (220–405 °C) and and at a space velocity of 40,000 h^?1 and is resistant to poisoning by halogenated and amine volatile organic compounds.     

微波-Fenton对沼液中抗生素和激素的高级氧化

采用微波强化Fenton氧化处理系统,研究H2O2浓度、Fe2+浓度、初始pH、微波辐射时间和微波辐射功率对沼液中喹乙醇、土霉素、四环素及金霉素降解效果的影响.结果发现,采用微波强化Fenton氧化降解沼液中抗生素与激素的最优条件是:H2O2浓度为40 mg/L、Fe2+浓度为12 mg/L、初始pH为4、微波辐射时间为2 min、微波辐射功率为中火(445W),沼液中喹乙醇、土霉素、四环素、金霉素和COD的去除率分别达到67％、93％、91％、88％和46％.在水浴条件下,与单独微波辐射和单独Fenton相比,微波强化Fenton氧化有明显的优越性.     

Long-term evaluation of activated carbon as an adsorbent for biogas desulfurization

ABSTRACT

In this study, granular activated carbon (GAC) was used as an adsorbent for biogas desulfurization. Biogas containing 932–2,350 ppm of H₂S was collected from an anaerobic digester to treat the wastewater from a dairy farm with about 200 cows. An adsorption test was performed by introducing the biogas to a column that was packed with approximately 50 L of commercial GAC. The operation ceased if the effluent gas had an H₂S concentration of over 100 ppm. The GAC was replaced by a given weight of new GAC in a subsequent test. According to the results, for H₂S concentrations in the range of 932–1,560 ppm (average±SD = 1,260 ± 256 ppm), 1 kg of the GAC yielded biogas treatment capacities of 568 ± 112 m³ and H₂S adsorption capacities of 979 ± 235 g. For the higher influent H₂S concentrations of 2,110 ± 219 ppm, the biogas treatment and H₂S-adsorption capacities decreased to 229 ± 18 m³ and 668 ± 47 g, respectively. An estimation indicated a requisite cost of US$16.5 for the purification of 1,000 m³ of biogas containing 2,110 ppm of H₂S. This cost is approximately 5% of US$330, the value of 1,000 m³ of biogas.     

Hydrogen Sulfide Removal From Hot Producer Gas With Sintered Absorbents

The Bureau of Mines prepared three sintered materials capable of removing H₂S from producer gas at 1000° to 1500°F. They are mixtures of ferric oxide and fly ash, ferric oxide and pumice stone, and red mud (a ferric oxide-containing residue from processing bauxite). All three absorbents were virtually completely regenerable with air. A sintered Fe₂O₃; (25%)-fly ash [75%) mixture was tested through nine H₂S absorption-air regeneration cycles without loss of absorplion capacity or attrition of the pellets. The absorbent with the greatest capacity was a red mud, absorbing 16.0% by weight of sulfur at 1000° F, 24.0% at 1250° F, and 45.1 % at 1 500° F.     

Fenton氧化法同时脱硫脱硝的实验研究

应用Fenton液相氧化吸收法进行同时脱硫脱硝实验。首先,利用单因素实验,分别考察了H2O2浓度、Fe2+投加量、初始pH值、UV照射和温度对脱硫脱硝的影响。结果表明,SO2和NO去除率随着H2O2浓度和Fe2+投加量的增大而提高;初始pH对SO2和NO的去除有较大影响;UV能促进SO2和NO的净化;温度对脱硫效率影响不大,但对NO的去除有显著作用,适当升温可以提高脱硝效率。随后,考察了SO2对NO去除率的影响。通过单独脱硝和同时脱硫脱硝的对比实验发现,SO2的加入对NO的去除有一定的促进作用,Fenton法可同时获得起始约80%的脱硝效率和98%以上的脱硫效率。     

4种高级氧化法处理高浓度正丙醇废水的动力学比较

研究了1%和10%(V/V)模拟正丙醇废水在UV/TiO2体系、UV/H2O2体系、Fe2+/H2O2体系和UV/TiO2/Fe2+/H2O2体系等4种工艺条件下的降解动力学过程,对比了降解动力学特点及工艺参数对动力学常数的影响,优化工艺参数。结果表明,UV/TiO2体系和Fe2+/H2O2体系的降解过程可分为零级反应阶段和一级反应阶段,转折点分别在反应开始后2 h和氧化剂浓度为6.7 g/L,UV/H2O2体系和UV/TiO2/Fe2+/H2O2体系分别符合零级反应和一级反应规律;相同工艺参数条件下,6 h反应后,组合工艺UV/TiO2/Fe2+/H2O2体系在处理效率达85%,比前3个体系分别高52.0%、8.3%和32.0%,与UV/TiO2体系和Fe2+/H2O2体系的处理效率之和持平,其协同效应提高了速率常数,在目标物浓度降低时依然可维持较高降解速率。而目标物浓度提高10倍后,UV能量利用率提高35.5倍,氧化剂用量是Fe2+/H2O2体系的1/7.1。     

Improving the Fenton process by visible LED irradiation

The effect of irradiation with visible light-emitting diode (LED) light on the efficiency of Fenton oxidation is investigated using phenol as the target compound (100 mg/L). The H₂O₂ dose and temperature are tested as operating variables with the aim of minimizing consumption of the reagents. At 50 °C, 10 mg/L Fe²⁺, and 60 % of the stoichiometric H₂O₂ amount, phenol was completely oxidized into CO₂, H₂O, and short chain organic acids, with oxalic acid completely degraded. Up to 95 % mineralization was achieved. This high efficiency can be attributed to the effect of LED radiation on the quinones/Fe²⁺/Fe³⁺/H₂O₂ cycle, which significantly increases the reaction rate, as well as on the photodecomposition of the iron complexes formed along the oxidation process, which also enhanced mineralization.     

含铁材料对污染水稻土中砷的稳定化效果

通过化学实验方法,向砷污染水稻土中添加4种含铁材料(FeCl3、FeCl2、Fe0和Fe2O3),分析稳定后土壤中pH、砷形态及砷毒性浸出量的变化,研究4种含铁材料对污染水稻土中砷的稳定化效果。结果表明,FeCl3和FeCl2处理降低了土壤pH,Fe0和Fe2O3处理对土壤pH影响不大。4种含铁材料均明显降低了土壤中易溶态砷(WE-As)和毒性浸出砷含量。在最大添加量为8.00 g/kg时,FeCl3、FeCl2、Fe0和Fe2O3分别使易溶态砷比对照降低了86.4%、63.6%、77.3%和36.4%,使毒性浸出砷比对照降低了96.3%、88.9%、70.4%和30.4%。4种含铁材料均对水稻土壤中砷具有较好的稳定化效果,且能力大小依次为:FeCl3FeCl2、Fe0Fe2O3。Fe0和Fe2O3处理使WE-As、铝型砷(Al-As)、铁型砷(Fe-As)向钙型砷(Ca-As)和残渣态砷(RS-As)转化;FeCl3处理使土壤WE-As、Al-As向Fe-As、Ca-As和RS-As转化;FeCl2处理使土壤WE-As、Ca-As向Al-As、Fe-As转化,对RS-As影响不明显。说明Fe0固砷的机理与Fe2O3相似,与FeCl3有一定差异,与FeCl2的差异可能更大。     

Study on the removal of elemental mercury from simulated flue gas by Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>-CeO<Subscript>2</Subscript>/AC at low temperature

Fe₂O₃ and CeO₂ modified activated coke (AC) synthesized by the equivalent-volume impregnation were employed to remove elemental mercury (Hg⁰) from simulated flue gas at a low temperature. Effects of the mass ratio of Fe₂O₃ and CeO₂, reaction temperature, and individual flue gas components including O₂, NO, SO₂, and H₂O (g) on Hg⁰ removal efficiency of impregnated AC were investigated. The samples were characterized by Brunauer–Emmett–Teller (BET), X-ray diffraction (XRD), scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS). Results showed that with optimal mass percentage of 3 % Fe₂O₃ and 3 % CeO₂ on Fe3Ce3/AC, the Hg⁰ removal efficiency could reach an average of 88.29 % at 110 °C. Besides, it was observed that O₂ and NO exhibited a promotional effect on Hg⁰ removal, H₂O (g) exerted a suppressive effect, and SO₂ showed an insignificant inhibition without O₂ to some extent. The analysis of XPS indicated that the main species of mercury on used Fe3Ce3/AC was HgO, which implied that adsorption and catalytic oxidation were both included in Hg⁰ removal. Furthermore, the lattice oxygen, chemisorbed oxygen, and/or weakly bonded oxygen species made a contribution to Hg⁰ oxidation.     

Recycling of iron and silicon from drinking water treatment sludge for synthesis of magnetic iron oxide@SiO<Subscript>2</Subscript> composites

More attention has been paid to the deterioration of water bodies polluted by drinking water treatment sludge (DWTS) in recent years. It is important to develop methods to effectively treat DWTS by avoiding secondary pollution. We report herein a novel investigation for recovery of Si and Fe from DWTS, which are used for the synthesis of two iron oxide@SiO₂ composites for adsorption of reactive red X-3B (RRX-3B) and NaNO₂. The results show that Fe³⁺ (acid-leaching) and Si⁴⁺ (basic-leaching) can be successfully recovered from roasted DWTS. Whether to dissolve Fe(OH)₃ precipitation is the key point for obtaining Fe₃O₄ or γ-Fe₂O₃ particles using the solvothermal method. The magnetic characteristics of Fe₃O₄@SiO₂ (390.0 m² g^?1) or Fe₂O₃@SiO₂ (220.9 m² g^?1) are slightly influenced by the coated porous SiO₂ layer. Peaks of Fe–O stretching vibration (580 cm^?1) and asymmetric Si–O–Si stretching vibrations (1080 cm^?1) of Fe₃O₄@SiO₂ indicate the successful coating of a thin silica layer (20–150 nm). The adsorption capacity of RRX-3B and NaNO₂ by Fe₃O₄@SiO₂ is better than that of Fe₂O₃@SiO₂, and both composites can be recycled through an external magnetic field. This method is an efficient and environmentally friendly method for recycling DWTS.