污泥焚烧底灰中重金属残留特性的实验研究

利用原子吸收分光光度计和程序控制温升炉研究了沈阳市污水处理厂污泥在不同焚烧工况下重金属Cu,Cr,Cd,Zn,Ni和Pd在焚烧底灰中的残留特性，考察了升温速率，焚烧温度，含水率以及停留时间等因素对重金属在污泥底灰中的残留特性的影响，实验表明，Pd,Cd和Cu在灰渣中的残留率随着渐度和停留时间的增加而降低，大部分的重金属元素Zn,Cr和Cu残留在灰渣中，Cd,Pb和Ni部分残留在灰渣中。     

底灰动态吸附焦化和造纸废水研究

分析了底灰的化学组成、矿物组成和比表面积等基本理化性质;采用动态吸附柱法研究了底灰处理焦化和造纸废水的性能,探讨了进水流量和吸附柱高度对吸附效果的影响.结果表明,底灰不仅有吸附作用,还具有一定的混凝作用;颗粒态有机碳(POC)较易被混凝除去,焦化废水中POC占总有机碳(TOC)的17%,而造纸废水中POC仅占TOC的2.3%,因此底厌对焦化废水COD的去除效果比造纸废水好;底灰对焦化废水色度的去除率要高于COD;接近吸附饱和时,底灰对造纸废水OM275的去除率仍有约27%,说明造纸废水中苯环类物质相比于其他有机物较易被去除.     

城市垃圾焚烧底灰资源化处理的可行性研究

对天津某城市垃圾焚烧发电厂的垃圾焚烧底灰进行采样,测试评价了不同粒径焚烧底灰的工程特性及环境风险,并以焚烧底灰为骨料制备混凝土平板试件,分析了焚烧底灰中杂质组分对再生建筑材料的工程特性影响.研究发现,焚烧底灰的颗粒级配分布、主要元素成分及含量、砂当量、压实强度与天然建筑骨料相似,且不同粒径的焚烧底灰在使用过程中无毒性重...     

污泥焚烧底灰中重金属残留特性的实验研究

利用原子吸收分光光度计和程序控制温升炉研究了沈阳市污水处理厂污泥在不同焚烧工况下重金属Cu、Cr、Cd、Zn、Ni和Pb在焚烧底灰中的残留特性。考察了升温速率、焚烧温度、含水率以及停留时间等因素对重金属在污泥底灰中的残留特性的影响。实验表明 ,Pb、Cd和Cu在灰渣中的残留率随着温度和停留时间的增加而降低。大部分的重金属元素Zn、Cu和Cr残留在灰渣中 ,Cd、Pb和Ni部分残留在灰渣中     

垃圾焚烧底灰固化污水厂污泥的岩土工程性质实验

对污水处理厂污泥采用垃圾焚烧底灰进行固化处理,分别测试不同掺量和不同养护龄期时固化体的岩土工程性质,通过测试发现,固化体重度基本位于11～13 kN/m3之间,与垃圾焚烧底灰的重度相近;固化体含水率随着垃圾焚烧底灰掺量的增大而急剧减小;抗剪强度指标和无侧限抗压强度随垃圾焚烧底灰的掺量增加和养护龄期的增长而增大,其内摩擦角位于10°～30°之间。建立的固化强度预测模型,可对不同掺量和龄期的固化污泥强度进行预测。     

脱硫灰-石灰石湿法脱硫石膏中杂质悬浮分离实验

根据脱硫灰及石膏的特性，在无挡板平底圆筒搅拌槽内，对脱硫石膏中的杂质进行完全离底悬浮分离实验，研究结果表明，完全离底悬浮搅拌时，悬浮高度比越低，越有利于杂质分离。对于直径D≥24cm的搅拌槽，当桨叶离底高度cb=4cm，桨径槽比d／D=0．65，杂质分离效率叼最高，约82％；当直径D=20cm时，杂质分离效率η随d／D的增大而增大，桨叶离底间距减小，杂质分离效率受d／D影响程度减小；当桨叶离底高度cb=4cm时，随着搅拌槽直径D的增大，杂质分离效率总体呈现增大趋势，降低桨叶离底高度cb杂质分离效率变化较大；进行完全离底悬浮分离后，石膏纯度提高。     

喷钙脱硫灰在高温条件下的稳定性研究

对喷钙脱硫灰在高温条件下的稳定性进行了研究，通过对不同CaSO3,CaO含量的脱硫灰在不同气氛下CaO3的分解规律来考察其稳定定性。结果表明，温度和灰中CaO对脱硫灰的稳定性有直接影响。CaO3的分解率随温度的升高而升高，随CaO含量的增多而降低；气氛中含有氧气对其稳定性有重要作用，氧气能使其生成性能稳定的CaSO4，因此，高温利用脱硫灰时，在1150℃以下，空气中仅有极微量的SO2放出，不会对环境造成危害。     

NID半干法脱硫灰生产蒸压砖中试实验研究

为了实现NID半干法脱硫灰综合利用,对利用吉林某电厂NID半干法脱硫灰作为主要原料在现有生产线生产蒸压砖进行研究,中试实验结果表明,在对现有生产线的各工艺参数进行调整及配方优化下,可以解决直接利用NID半干法脱硫灰为蒸压砖主要原材料所产生的诸如层裂、龟裂、强度低等问题,生产出30%NID半干法脱硫灰添加量的蒸压砖。并在对NID半干法脱硫灰进一步预处理下,生产出40%NID半干法脱硫灰添加量的蒸压砖。产品满足国家M15标准规定的外观、强度及抗冻融性等指标。     

基于响应曲面法优化烧结烟气脱硫灰改性工艺

采用BOX-Behnken的中心组合实验设计及响应面分析方法对半干法烧结烟气脱硫灰进行改性研究,得到脱硫灰转化率的预测模型。结果表明:通过该预测模型可以很好地描述脱硫灰的转化率与反应温度、反应时间和气固比等重要操作参数之间的关系,R2=0.9903。因素分析表明,反应温度对脱硫灰的转化率影响最大,同时反应温度和气固比的交互作用与反应温度和时间的交互作用对脱硫灰的转化率的影响作用相同。利用得到的改进预测模型可以计算脱硫灰的转化率。     

半干半湿法脱硫灰循环利用中试试验研究

半干半湿法脱硫产生的脱硫灰中混有大量有效钙和粉煤灰，本文对其进行了循环利用机理分析及试验研究，证实脱硫灰循环大大提高了钙的利用率，降低了钙硫比，但循环倍率增加到2倍以上时，脱硫效率增速变缓。脱硫灰的循环利用对降低脱硫运行费用是非常有效的。     

垃圾焚烧发电过程中的二次污染物控制处理技术

概述了二口恶英、重金属、酸性气体、灰渣等垃圾焚烧二次污染物的形成机理，并详细介绍了通过控制垃圾焚烧条件、尾气处理以及吸附等方法，可以有效控制二口恶英类污染物的排放；重金属的控制可以用除尘器或使用相应的吸附剂处理；采用较为成熟的烟气处理技术，可以控制处理酸性气体；灰渣可采用固化稳定化和酸或其他溶剂提出法处置。     

典型建筑固体废弃物再生骨料对环保砖性能的影响

随着我国城市化和工业化进程的快速推进,城市建设产生大量的建筑废弃物,燃煤电厂产生大量炉底渣,建筑固废的处置在城市可持续发展过程中备受关注。以建筑垃圾再生骨料、炉底渣和石粉等区域特色的骨料制备环保砖,系统考察了骨料对环保砖力学性能的影响。实验结果表明,再生骨料的种类对环保砖抗压强度的影响显著。再生骨料中混凝土的增加,环保砖抗压强度逐渐增加;而再生骨料中粘土砖含量的增加,环保砖抗压强度明显降低。环保砖抗压强度随炉底渣的含量增加而降低,石粉对环保砖抗压强度有提升作用。     

From agricultural use of sewage sludge to nutrient extraction: A soil science outlook

The composition of municipal wastewater and sewage sludge reflects the use and proliferation of elements and contaminants within society. In Sweden, official statistics show that concentrations of toxic metals in municipal sewage sludge have steadily decreased, by up to 90 %, since the 1970s, due to environmental programmes and statutory limits on metals in sludge and soil. Results from long-term field experiments show that reduced metal pollution during repeated sewage sludge application has reversed negative trends in soil biology. Despite this Swedish success story, organic waste recycling from Swedish towns and cities to arable land is still limited to only about 20 % of the total amount produced. Resistance among industries and consumers to products grown on land treated with sewage sludge may not always be scientifically grounded; however, there are rational obstacles to application of sewage sludge to land based on its inherent properties rather than its content of pollutants. We argue that application of urban organic wastes to soil is an efficient form of recycling for small municipalities, but that organic waste treatment from large cities requires other solutions. The large volumes of sewage sludge collected in towns and cities are not equitably distributed back to arable land because of the following: (i) The high water and low nutrient content in sewage sludge make long-distance transportation too expensive; and (ii) the low plant availability of nutrients in sewage sludge results in small yield increases even after many years of repeated sludge addition. Therefore, nutrient extraction from urban wastes instead of direct organic waste recycling is a possible way forward. The trend for increased combustion of urban wastes will make ash a key waste type in future. Combustion not only concentrates the nutrients in the ash but also leads to metal enrichment; hence, direct application of the ash to land is most often not possible. However, inorganic fertiliser (e.g. mono-ammonium phosphate fertiliser, MAP) can be produced from metal-contaminated sewage sludge ash in a process whereby the metals are removed. We argue that the view on organic waste recycling needs to be diversified in order to improve the urban–rural nutrient cycle, since only recycling urban organic wastes directly is not a viable option to close the urban–rural nutrient cycle. Recovery and recycling of nutrients from organic wastes are a possible solution. When organic waste recycling is complemented by nutrient extraction, some nutrient loops within society can be closed, enabling more sustainable agricultural production in future.     

煤矸石和粉煤灰pH与电导率动态变化规律及其相关性研究

煤矸石和粉煤灰是煤矿区两种常见的固体废弃物,对环境造成极大的污染。pH波动幅度大是废弃物农用治理的主要障碍之一。对两种废弃物连续浸提时的pH和电导率(EC)进行长期动态监测,结果表明,不同层次的煤矸石尽管风化程度不同,但经过长时间浸取后,pH和EC变化趋势相似,且煤矸石、粉煤灰的pH、EC值有很大的相关性。该试验为今后两种废弃物合理利用奠定了基础。     

Cytotoxicity of municipal solid waste incinerator ash wastes toward mammalian kidney cell lines

In this study, three municipal solid waste incinerator (MSWI) ash wastes-bottom ash, scrubber residue, and baghouse ash-were extracted using a toxicity characteristic leaching procedure (TCLP) extractant. These so-called final TCLP extracts were applied to African green monkey kidney cells (Vero), baby hamster kidney cells (BHK-21), and pig kidney cells (PK-15), multi-well absorption reader analysis was performed to test how the cytotoxicity of the incineration ashes would affect the digestive systems of animals. Ion-coupled plasma analyses indicated that the baghouse ash extract possessed the highest pH and heavy metal concentration, its cytotoxicity was also the highest. In contrast, the bottom ash and the scrubber residue exhibited very low cytotoxicities. The cytotoxicities of mixtures of baghouse ash and scrubber residue toward the three tested cell lines increased as the relative ratio of the baghouse ash increased, especially for the Vero cells. The slight cytotoxicity of the scrubber residue arose mainly from the presence of Cr species, whereas the high cytotoxicity of the baghouse ash resulted from its high content of heavy metals and alkali ions. In addition, it appears that the dissolved total organic carbon content of these ash wastes can reduce the cytotoxicity of ash wastes that collect in animal cells.     

典型危险废物的工程力学特性

掌握填埋废物的工程力学特性是确保危险废物填埋堆体稳定性的重要前提条件,因此,针对6种典型危险废物的工程力学特性开展了调查研究.研究结果表明,污泥类危险废物的含水率和有机质含量远高于非污泥类危险废物,而前者的比重则显著低于后者.污泥类危险废物的渗透系数相对较小,比污染土壤和飞灰炉渣混合物的渗透系数小1个数量级,比滤池填料的渗透系数小2个数量级.不同危险废物的无侧限抗压强度排序为:飞灰炉渣混合物(314.3 kPa)和滤池填料(278.9 kPa)＞污染土壤(124.9 kPa)＞杭州氧气厂污泥(68.6 kPa)、锌铬污泥(71.4 kPa)、油泥(58.4 kPa).不同危险废物的粘聚力排序为:飞灰炉渣混合物(40.8 kPa)、滤池填料(31.1 kPa)＞污染土壤(20.9 kPa)＞杭州氧气厂污泥(1.94kPa)、锌铬污泥(3.10 kPa)、油泥(1.81 kPa).此外,不同危险废物的内摩擦角差异相对较小,其变化范围在18.8°～35.0°之间.综合分析可知,飞灰炉渣混合物和滤池填料的工程力学特性较好,而污泥类危险废物的工程力学特性则较差.     

Effect of thermal processing on the characteristics of incineration fly ash

This work investigated the possibilities of immobilizing incineration fly ash by applying different processing methods. Direct sintering of fly ash at 1050 degrees C produced material with increased resistance to leaching; however, the high content of halides prevented the achievement of appropriate strength. Fly ash melting and casting into metallic moulds resulted in the formation of glass with good chemical resistivity and mechanical properties, which were further improved by devitrification, and the formation of glass-ceramics. The most successful combination of strength and resistance to leaching was obtained by a process consisting of fly ash melting, by pouring the melt into water, then grinding, and sintering without additives at 850-950 degrees C. In this way, a material was produced that cannot only be landfilled as a stabilised and non-reactive waste in landfills for non-hazardous wastes, but can also be utilized as a valuable material for manufacturing useful products. This article provided valuable results for policy-makers in Slovenia, about the handling fly ash from incineration plants. Implications: Fly ash from an incineration plant was thermally treated using several processing routes. Ash-melting, by pouring the melt into water and sintering, produced glass-ceramics having an optimal combination of strength and resistance to leaching that can find applications as useful products. These results provide important data for policy makers in Slovenia regarding the building of incineration plants, and handling the solid-waste products, especially fly ash.     

Waste Streams,Technology, and State Requirements

Biomedical wastes are generated by hospitals, laboratories, animal research facilities, and by other institutional sources. The disposal of these wastes is coming under critical public scrutiny, and regulations are being promulgated to control their disposal. Incineration is not a final disposal method since it generates a solid residue (ash) which must be buried or otherwise disposed. The incineration process, however, renders the waste non-toxic, non-hazardous, and non-putrescible, and reduces the volume of material for ultimate disposal by an order of magnitude. In some instances, the residue may have high levels of heavy metals; however, this is the exception rather than the rule.     

固体废弃物对新拌水泥浆体密实度与强度的影响

研究固体废弃物(石灰石粉、粉煤灰、赤泥和矿渣)作掺合料颗粒体系与新拌浆体填充密实性能的关系;分析了在水胶比为0.3时,以上4种固体废弃物以不同比例等质量取代水泥的净浆强度。实验结果表明,石灰石粉、粉煤灰、赤泥作为掺合料,能够改善胶凝材料的颗粒级配,填充新拌水泥浆体中的孔隙,使浆体更为密实,并且对其净浆的强度有利。     

HISTORY of the Air Pollution Control Association

Bottom ash is a waste material from coal-fired power plants, and it is known to contain elements that are potentially toxic at high concentration levels when disposed in landfills. This study investigates the use of bottom ash as a partial substitute sorbent for wet flue gas desulfurization (FGD) processes by focusing on its leaching kinetics in adipic acid. This was studied basing on the shrinking core model that was applied to the experimental data obtained by the authors presented at the International Conference on Industrial, Manufacturing, Automation and Mechanical Engineering, Johannesburg, South Africa, November 27–28, 2013) on dissolution of bottom ash. The leaching rate constant was obtained from different reaction variables, namely, temperature, pH, acid concentration, and solid-to-liquid ratio, that could affect the leaching process. The solid sample of bottom ash was characterized at different leaching periods using X-ray diffraction (XRD) and scanning electron microscopy (SEM). It was found that solid-to-liquid ratio had a significant effect on the leaching rate constant when compared with other variables. The leaching kinetics showed that diffusion through the product layer was the rate-controlling step during leaching, and the activation energy for the process was found to be 18.92 kJ/mol.

Implications:?The use of coal bottom ash waste as a sorbent substitute in wet flue gas desulfurization (FGD) has both economic and environmental advantages. This is because it is a waste from coal-fired thermal power plant and this study has proven that it can leach out a substantial amount of calcium ions for wet FGD process. This will abate anthropogenic pollution due to landfill disposal of bottom ash wastes and also reduce sulfur dioxide emissions.