4种脂肪多胺修饰硅胶对铅离子的吸附

为了合成高效铅离子吸附剂,了解其对铅离子的吸附规律。采用(3-氯丙基)三甲氧基硅烷(CPTS)架桥法,以硅胶(SG)为载体,乙二胺(EDA)、二乙烯三胺(DETA)、三乙烯四胺(TETA)和四乙烯五胺(TEPA)为表面修饰剂,合成了4种胺化硅胶,测定了它们的红外光谱、热重等性质以及对Cu2+、Zn2+和Pb2+的吸附能力。结果表明,4种胺化硅胶对Pb2+的吸附量均大于Cu2+和Zn2+的吸附量,其中DETA修饰硅胶对Pb2+的吸附量较高。4种胺化硅胶对Pb2+的吸附过程较好地符合拟二级动力学模型以及Langmuir和Scatchart等温吸附热力学模型,其对Pb2+吸附的速率常数、饱和吸附量以及吸附位点数由大到小的顺序一致,均为SG-DETASG-TEPASG-EDASG-TETA。4种胺化硅胶对Pb2+的吸附速率和吸附量呈现"奇数胺"增强效应,亲和常数则依次减小。阐明了脂肪多胺修饰硅胶对Pb2+的吸附规律,并进一步讨论了Scatchart和Langmuir热力学模型的统一性。     

皂化改性橘子皮生物吸附剂对重金属离子的吸附

以生物废料橘子皮(OP)为原料,经乙醇、氢氧化钠处理,得到改性橘子皮生物吸附剂SOP,将其用于对重金属离子Cu2+、Pb2+、Cd2+、Zn2+和Ni2+的吸附。研究了溶液pH、吸附时间和重金属离子初始浓度对SOP吸附性能的影响。结果表明,重金属离子在生物吸附剂上的吸附速率快,符合准二级动力学方程。SOP对重金属离子的吸附等温线符合Lang-muir模型,根据Langmuir模型计算SOP对Cu2+、Pb2+、Cd2+、Zn2+和Ni2+的饱和吸附量分别为56.82、152.4、66.27、33.90和23.02 mg/g,均高于改性前。常见阳离子的存在对重金属离子吸附的影响较小,改性后的橘子皮生物吸附剂可以再生重复使用4次以上,是性能良好的重金属离子吸附剂。     

三乙二醇二甲基丙烯酸酯为交联剂制备的高吸水树脂对重金属的吸附

以前期工作中合成的树脂PAANa-TE为吸附剂进行重金属吸附测试,考察吸附剂用量、丙烯酸中和度、吸附时间、溶液pH、初始浓度和吸附温度对树脂吸附重金属离子Cu2+、Pb2+、Cr3+和Co2+性能的影响,用原子吸收分光光度计测定了树脂吸附Cu2+、Pb2+、Cr3+和Co2+后的残留浓度,树脂对4种金属离子的吸附容量分别为21.59、2.39、5.66和4.98 mmol/g,吸附容量大小为Cu2+Cr3+Co2+Pb2+,吸附速率顺序为Cr3+Pb2+Cu2+Co2+。结果表明,该树脂对高浓度重金属离子有较快速,高效率的吸附,吸附过程在100 min左右吸附容量达到最大,并用不同浓度的酸对吸附重金属离子的树脂进行脱附处理,脱附量很小,据此可考虑进一步对金属离子进行回收处理。且脱附率较低,因此,可对工业化和城市化进程所产生的各种化学形态的重金属水体污染物造成的生态环境和质量问题起到重要的改善作用。     

改性啤酒酵母及柑橘皮凝胶小球对铜的吸附性能

为有效去除污水中的铜离子并实现资源有效的利用,以啤酒酵母和柑橘皮为原料制备海藻酸钙固定啤酒酵母菌小球(SCA)、海藻酸钙固定柑橘皮小球(OPCA)及海藻酸钙固定柑橘皮及啤酒酵母菌复合小球(OPSCA),研究了其对铜离子的吸附和解吸性能。研究结果表明,3种吸附剂对铜离子吸附的最佳pH值为5.0,吸附量的大小顺序为:OPSCAOPCASCA。吸附动力学数据符合准二级动力学模型。吸附过程被内扩散步骤和外扩散步骤共同控制。Langmuir等温吸附模型能较好地模拟3种吸附剂的吸附数据,SCA、OPCA及OPSCA的理论最大吸附量分别为33.49、40.80和61.69 mg/g。3种吸附剂可利用0.1 mol/L的盐酸解吸再生,可循环使用3次以上。     

改性松针对水体中铅(II)的吸附

探讨了改性松针(GXLsp)作为吸附剂对水体中铅离子的吸附性能,考察了吸附时间、溶液pH值、吸附剂用量、盐离子浓度、Pb(II)初始浓度及温度对改性松针吸附Pb(II)的影响。利用Langmuir和Freundlich等温线模型对实验数据进行非线性拟合分析,结果表明,Freundlich等温线模型能很好地描述松针对Pb(II)的吸附过程。热力学参数表明吸附是一个自发的吸热过程。改性松针对铅的吸附行为符合拟二级动力学方程,表明吸附过程是以化学吸附为主。在293K时松针对Pb(II)的饱和吸附量为318.3 mg/g,因此,GXLsp可作为一种高效低值生物质吸附剂以去除水体中重金属Pb(II)的污染。     

一株产絮酵母菌废菌体对Cd2+的吸附特性

将一株产絮酵母菌(编号B-02号)发酵后的废菌体制成生物吸附剂,研究该生物吸附剂对废水中Cd2+的生物吸附特性。结果表明:(1)pH值对Cd2+会产生较大的影响,偏酸性(pH=4～6)条件利于吸附;该吸附剂对Cd2+吸附速率较快,8～10 min就可达到吸附平衡;(2)吸附剂的吸附动力学符合二级动力学模型,吸附Cd2+的实验数据对Langmuir等温式的拟合情况良好,吸附剂吸附Cd2+的最大吸附量为70.752 mg/g。用0.5 mol/L HNO3对吸附Cd2+的酵母菌进行解吸,解吸率可达89.7%。     

改性甘蔗渣对Cu2+和Zn2+的吸附机理

研究了均苯四甲酸二酐(PMDA)和乙二胺四乙酸二酐(EDTAD)改性甘蔗渣对重金属离子Cu2+和Zn2+的吸附性能,包括吸附动力学和吸附等温线。结果表明,改性后的甘蔗渣对重金属离子Cu2+和Zn2+的吸附容量有显著提高,对Cu2+和Zn2+吸附等温线均符合Langmuir方程,吸附为单分子层吸附。根据Langmuir方程,PMDA和EDTAD改性甘蔗渣对Cu2+的吸附量分别为60.21和33.45 mg/g,对Zn2+的吸附量分别是70.53和36.53 mg/g。两种改性甘蔗渣对两种金属离子的吸附在30 min内均可完成,用准二级吸附动力学方程模拟动力学过程得到较好的线性相关性。以EDTA溶液为洗脱剂对吸附Cu2+和Zn2+的改性甘蔗渣进行洗脱再生,再生的吸附剂可反复使用。     

Zn/Al双金属氧化物对水中硫酸根离子的吸附性能

研究了用Zn/Al水滑石制得的Zn/Al双金属氧化物(Zn/Al-300)吸附剂对水中硫酸根离子的吸附,考查了吸附剂投加量、初始pH等因素对硫酸根离子吸附的影响。结果表明,Zn/Al-300对水中硫酸根离子的吸附符合Langmuir吸附等温方程,理论最大吸附量为62.5 mg/g。运用动力学方程进行拟合,吸附过程符合准二级动力学方程;溶液的pH影响吸附剂对硫酸根的吸附,在pH=5.5时硫酸根的去除率最大;X射线衍射结果显示,水滑石经过焙烧后丧失了原有的构形,并在吸附硫酸根离子后重新恢复水滑石的部分层状结构。吸附机制主要为Zn/Al-300从溶液中获取阴离子以重建水滑石的晶体结构,即"记忆效应"。对吸附后的双金属氧化循环应用4此后,吸附容量几乎不变,说明双金属氧化物具有可循环型。通过将Zn/Al-300与其他几种吸附剂的经济性分析,表明此吸附剂在使用过程中具有一定优势。     

K+、Na+、Ca2+共存离子对活性炭吸附Cr(Ⅵ)的影响

以含有重金属离子Cr(Ⅵ)以及共存轻金属离子K~+、Na~+、Ca~(2+)的模拟废水为研究对象,采用活性炭进行吸附处理,探讨了3种共存轻金属离子对活性炭吸附Cr(Ⅵ)的影响。结果表明:(1)共存的K~+、Na~+、Ca~(2+)与Cr(Ⅵ)之间存在竞争吸附,其影响活性炭吸附Cr(Ⅵ)的大小顺序为Ca~(2+)Na~+K~+,其中Ca~(2+)导致Cr(Ⅵ)去除率下降44.16百分点。(2)吸附Cr(Ⅵ)的活性炭在2 170cm~(-1)处出现新的红外振动峰,表明Cr(Ⅵ)与活性炭之间的吸附属于化学吸附。在同时吸附Cr(Ⅵ)与共存离子的样品中,未出现新的红外振动峰,表明K~+、Na~+、Ca~(2+)与活性炭间的吸附属于物理吸附。(3)活性炭吸附Cr(Ⅵ)的过程符合Langmuir模型,属于单分子层化学吸附;其动力学曲线符合伪二级动力学模型。     

新型材料淀粉微球对Cu~(2+)、Cr~(3+)和Pb~(2+)的吸附机理研究

以可溶性淀粉为原料,在反相悬浮体系中合成N,N′-亚甲基双丙烯酰胺交联淀粉微球为载体,研究了新型吸附材料淀粉微球(cross-linked starch microsphere,CSMs)对Mn+(Cu2+、Cr3+、Pb2+)的静态吸附行为。利用扫描电镜、X射线衍射仪和红外光谱仪对微球及其吸附产物进行表征,分析讨论了3种金属原子结构,研究了吸附机理。结果表明:308K时,Cu2+、Pb2+和Cr3+的饱和吸附量分别是2.43、0.30和0.27 mmol/g,CSMs对Cu2+离子吸附能力最强,并且其通过物理吸附、配位吸附方式吸附Mn+,并得出引起微球吸附能力大小可能与金属离子电荷、离子半径和外层电子排布的差异因素有关。     

Simultaneous heavy metal removal mechanism by dead macrophytes

The use of dead, dried aquatic plants, for water removal of metals derived from industrial activities as a simple biosorbent material has been increasing in the last years. The mechanism of simultaneous metal removal (Cd2+, Ni2+, Cu2+, Zn2+ and Pb2+) by 3 macrophytes biomass (Spirodela intermedia, Lemna minor and Pistia stratiotes) was investigated. L. minor biomass presented the highest mean removal percentage and P. stratiotes the lowest for all metals tested. Pb2+ and Cd2+ were more efficiently removed by the three of them. The simultaneous metal sorption data were analysed according to Langmuir and Freundlich isotherms. Data fitted the Langmuir model only for Ni and Cd, but Freundlich isotherm for all metals tested, as it was expected. The K(F) values showed that Pb was the metal more efficiently removed from water solution. The adsorption process for the three species studied followed first order kinetics. The mechanism involved in biosorption resulted ion exchange between monovalent metals as counter ions present in the macrophytes biomass and heavy metal ions and protons taken up from water. No significant differences were observed in the metal exchange amounts while using multi-metal or individual metal solutions.     

枯草芽孢杆菌对Cu2+的吸附及菌体表面基团分析

以枯草芽孢杆菌(Bacillus subtilis)为生物吸附剂,讨论了其对Cu2+的生物吸附规律,并通过酸碱滴定这一表面分析手段,结合相关软件及傅里叶变换红外光谱(FTIR)分析了菌体表面主要的基团种类及数量.结果表明,枯草芽孢杆菌对Cu2+吸附的最佳条件是:pH为6、吸附时间为24 h,菌悬液用量和Cu2+初始浓度...     

一株产絮酵母菌废菌体对Cd~（2＋）的吸附特性

将一株产絮酵母菌（编号B-02号）发酵后的废菌体制成生物吸附剂,研究该生物吸附剂对废水中Cd2＋的生物吸附特性。结果表明：（1）pH值对Cd2＋会产生较大的影响,偏酸性（pH=4～6）条件利于吸附;该吸附剂对Cd2＋吸附速率较快,8～10 min就可达到吸附平衡;（2）吸附剂的吸附动力学符合二级动力学模型,吸附Cd2＋的实验数据对Langmuir等温式的拟合情况良好,吸附剂吸附Cd2＋的最大吸附量为70.752 mg/g。用0.5 mol/L HNO3对吸附Cd2＋的酵母菌进行解吸,解吸率可达89.7%。     

Removal and mechanism of Cu (II) and Cd (II) from aqueous single-metal solutions by a novel biosorbent from waste-activated sludge

The removal and mechanism of Cu²⁺ and Cd²⁺ from aqueous single-metal solutions were investigated by using a novel biosorbent from waste-activated sludge. A series of adsorption experiments was designed to disclose the effects of the key factors on the adsorption capacity of the biosorbent for the metal ions. The mass ratio of the biosorbent to metal ion was optimized as 2 to balance the adsorption capacity and the removal efficiency. A right shaking speed (150 r/min) not only ensured enough contact frequency between the sorbent and the adsorbate but also reduced the mass transfer resistance. The natural pH value (about 5.5) of the metal solutions benefited a high adsorption capacity of the biosorbent and avoided the consumption of acid or base for pH adjustment. The adsorption reactions belonged to the endothermic process between 15 and 45 °C. As the scanning electron microscopy (SEM) images showed, the meshy structure with long chains and many branches was ideal for the biosorbent to quickly capture the metal ions. The energy-dispersive X-ray (EDX) spectra confirmed that the adsorbed metal ions lay in the precipitates of the adsorption reactions. According to the FTIR analyses, the functional groups responsible for Cu²⁺ adsorption majorly consisted of O–H, N–H, COOH, CONH₂, and the groups containing sulfur and phosphorus, while those for Cd²⁺ adsorption contained O–H, N–H, COOH, and CONH₂. The differences in the responsible functional groups explained the phenomenon that the adsorption capacity of the biosorbent for Cu²⁺ was higher than that for Cd²⁺.     

Effects of zinc on the structure and growth dynamics of a natural freshwater phytoplankton assemblage reared in the laboratory

The response of a natural phytoplankton assemblage to different concentrations of Zn(2+) was evaluated by means of a static laboratory bioassay. Aliquots of surface water, taken in autumn from a non-polluted point of the Reconquista River (Buenos Aires, Argentia), were incubated in mineral nutrient media containing 2.5, 10 or 25 mg litre(-1) of Zn(2+) (as zinc chloride). The comparative structure and dynamics of the communities were followed through periodic physico-chemical and biological analyses of samples taken during 24 days of incubation. Under the experimental conditions of the bioassays, the existence of several Zn(2+) tolerant algal species was shown: the most important of them were Chlorella vulgaris Beij. (Chlorophyceae, Chlorococcales), Nitzschia palea (Kütz.) Smith and Gomphonema parvulum (Kütz.) Kütz. (Bacillariophyceae). It was also demonstrated that the algal responses to Zn(2+) were selectively concentration dependent: at 2.5 and 10 mg litre(-1) a stimulatory effect was observed in the diatoms; at 25 mg litre(-1), diatom toxicity occurred. In contrast, Chlorophyceae growth was stimulated at the maximal Zn level. In general, the diversity, richness and equitability of the community were adversely affected by Zn in a concentration-dependent fashion.     

The preparation of Zn2+-doped TiO(2) nanoparticles by sol-gel and solid phase reaction methods respectively and their photocatalytic activities

The photocatalytic oxidation of the organic pollutants with TiO(2) as photocatalyst has been widely studied in the world, and many achievements have been made. The degradation of pollutants is highly related to the photocatalytic activity of TiO(2). It is demonstrated that doping ions to TiO(2) is one way to enhance the photocatalytic activity of TiO(2). In this paper, Zn(2+)-doped TiO(2) nanoparticles were prepared through sol-gel and solid phase reaction methods, characterized by means of X-ray diffraction (XRD) and transmission electron microscopy (TEM). The photocatalytic activity of the elaborated powders was studied following the degradation of Rhodamine B. The results showed that the photocatalytic activity of Zn(2+)-doped TiO(2) prepared by sol-gel method is close to that of pure TiO(2) particles, however, the photocatalytic activity of Zn(2+)-doped TiO(2) prepared by solid phase reaction method is much higher than that of pure TiO(2) particles. The most efficient degradation of Rhodamine B was found with TiO(2) particles doped with 0.5% Zn(2+) in mole and calcined at 500 degrees C. Also the reason for the enhancement of the photocatalytic activity of TiO(2) by Zn(2+) doping through solid phase reaction method was discussed.     

Sorption studies of heavy metal ions on a novel chelating resin and its application in the stripping of mercury (II)

A chelating resin containing a stable thiol group was synthesised, using polystyrene as the starting material. The resin is stable towards conc. HCl, 0.1M HNO(3) and 0.1M NaOH. The resin shows affinity towards Ag(+), Hg(2+), Bi(3+), Pb(2+), Cu(2+), Zn(2+) and Cd(2+). Extraction of these metal ions as a function of pH, kinetics of exchange and breakthrough capacities is evaluated. The selectivity of the resin for the metal ions is in the order Ag(+) > Hg2+ > Cu2+ > Pb2+ > Cd2+ > Zn2+. The equilibrium constants for exchange and kinetics of exchange are favourable for the recovery of mercury from lean sources. Application of the resin in the stripping of mercury from chlor-alkali plant affluent, and in the enrichment of mercury from seawater, have been investigated. Mercury sorbed resin can be regenerated using 5% thiourea in 0.1M HCl.     

Metal homeostasis in Hypogymnia physodes is controlled by lichen substances

The hypothesis was tested that the lichen substances produced by the epiphytic lichen Hypogymnia physodes control the intracellular uptake of divalent transition metals. Incubating lichen thalli with and without their natural content of lichen substances with metal solutions showed that the lichen substances of H. physodes selectively inhibit the uptake of Cu(2+) and Mn(2+), but not of Fe(2+) and Zn(2+). Such behavior is ecologically beneficial, as ambient concentrations of Cu(2+) and Mn(2+) in precipitation and bark are known to limit the abundance of H. physodes, whereas limiting effects of Fe(2+) or Zn(2+) have never been found. This suggests that increasing the Cu(2+) and Mn(2+) tolerance stimulated the evolution of lichen substances in H. physodes. The depsidone physodalic acid is apparently most effective at reducing Cu(2+) and Mn(2+) uptake among the seven lichen substances produced by H. physodes. Probably lichen substances play a general role in the metal homeostasis of lichens.