Comparative chemical mass closure of fine and coarse aerosols at two sites in south and west Europe: Implications for EU air pollution policies

The chemical composition of PM10 and PM2.5 was studied during summer and winter sampling campaigns in South and West Europe (Barcelona, Spain, and Ghent, Belgium). The chemical composition of the PM10 aerosol was markedly different in the two regions, even at similar PM10 levels. The chemical composition of PM2.5 showed more similarities. The contribution of mineral matter was higher in Barcelona (on average 12% of the PM2.5 mass), whereas the contribution from sea salt was higher in Ghent (4% of PM2.5). Volatilisation of NH₄⁺ from the filters (negative artefact) was observed in both regions, although the extent of this artefact showed regional differences (0–4% and 22–38% of the NH₄⁺ mass in Ghent and Barcelona, respectively) and had no impact on the compliance with EU limit values. The number of exceedances of the PM10 limit value and an arbitrary PM2.5 limit of 25 μg m⁻³ was calculated by subtracting the mineral fraction (natural or anthropogenic in origin) from the bulk PM load, and this resulted in the elimination of the PM10 exceedances in Barcelona, and a reduction of one out of three exceedances in Ghent. The subtraction of sea-salt aerosol had no effect in Barcelona, and it removed one exceedance in each size fraction in Ghent. Exceedances of the PM10 daily limit value in Ghent coincided with back-trajectories originating from Eastern and Southern European regions. The origin of the exceedances in Barcelona during the campaigns was mostly local.     

The aging process of naturally emitted aerosol (sea-salt and mineral aerosol) during long range transport

The aging processes of two representative natural aerosol, sea-salt and mineral aerosol, are investigated by using a box model equipped with a thermodynamic module (SCAPE). The model is shown to successfully describe the aging processes between the gas-phase anthropogenic pollutants (SO₂, NO_x, and NH₃) and primary aerosol particles, including self-neutralization process/chlorine depletion in the sea-salt aerosol; formation/dissipation of carbonate and bicarbonate ions in the mineral aerosol; irreversible dynamic deposition of SO₂ and H₂SO₄; and reversible thermodynamic distribution of inorganic volatile species. It is found that SO₂ and H₂SO₄ tend to deposit onto the mode with the largest surface area, and that ammonia deposition is controlled by preceding SO₂/H₂SO₄ deposition. During the SO₂/H₂SO₄ deposition, chloride and carbonate are continuously released from the sea-salt and mineral dust particles, respectively. The findings by the model predictions are consistent with field and observational studies.     

Visibility impairment during Yellow Sand periods in the urban atmosphere of Kwangju,Korea

For continuous monitoring of atmospheric visibility in the city of Kwangju, Korea, a transmissometer system consisting of a transmitter and a receiver was installed at a distance of 1.91 km across the downtown Kwangju, Korea. At the transmitter site a nephelometer and an aethalometer were also installed to measure the scattering and absorption coefficients of the atmosphere, respectively. Unusually high number of Yellow Sand events had occurred in the Northeast Asia during the spring of 2000. Visibility in Kwangju under such conditions was greatly impaired over large area for a few days. In order to investigate the effects of Yellow Sand on visibility impairment, chemical and elemental analyses of aerosol samples were performed along with the optical measurement of visibility. Hourly averaged visual range decreased from 61.7 to 1.9 km when hourly averaged concentration of PM10 varied from 32.9 to 601.8 μg/m³ during Yellow Sand periods. Fine particulate (<2.5 μm) concentrations were relatively lower than coarse particulate matters. Results of the data analyses show that mineral dusts originated from continental sources were simultaneously transported along with anthropogenic sulfate aerosols and marine aerosols. Total light extinction coefficient, b_ext, proposed by the IMPROVE network showed poor correlation with b_ext measured by transmissometer. Coarse mass scattering efficiency was classified into three categories; E_NHSOc, E_mineral, and E_sea-salt, which were determined as ammonium sulfate combined with nss-sulfate of 1.0, sea-salt of 0.4, and mineral of 0.77 m²/g, respectively. Mass fraction of NHSOc, sea-salt, and mineral dust was 0.20, 0.14, and 0.66, respectively.     

A method to determine the effect of mineral dust aerosols on air quality

Natural mineral dust storms (DS) from the Arabo-African region blow over the Mediterranean, reach Israel, and add to the anthropogenic particulate pollution. The effects of mineral dust on air quality in Israel were investigated using only PM10 and PM2.5 automatic measurements. The method does not require any other inputs such as satellite observations, model back-trajectories, dust forecast models, or mineralogical analyses. The method employs an automatic algorithm with three thresholds: the half-hour PM10 average must be above 100, this level is maintained for at least 3 h, and the maximum concentration recorded is above 180 μg m^?3. The algorithm was designed for Israel, but can be adapted for other locations.The contribution of DS caused PM10 values to exceed the Israeli annual standard of 60 μg m^?3 year^?1 in 6 of the 12 years examined. The DS contribution to PM10 annual average ranged from 9.4% to 29.5%. The level recommended by WHO, 20 μg m^?3 year^?1, was exceeded every year even without the DS contribution. The number of days in which the daily Israeli standard (150 μg m^?3) was exceeded during the 12 years was 6–20 days per year. The number of days in which the daily standard was exceeded shows an increasing trend of 7 days per decade.PM2.5 in Israel is in the range 40–56% of PM10. PM2.5 values were over the recommended standard with and without DS. The contribution of DS to annual average of PM2.5 ranged from 3.6% to 19.1%.The automatic algorithm was calibrated with a list of Dust Storms identified by visual means supported by mineralogical analysis. Mineralogical analyses of single particles were performed using Environmental Scanning Electron Microscope (ESEM). Two representative samples are given. The main difference is that the particles of the Saudi-Arabian storm had much more palygorskite, while the North-African storm had more sea-salt and organic particles. The mineral composition differences indicate that analysis can differentiate between sources.     

An integrated approach to identify the origin of PM10 exceedances

Purpose

This study was aimed to the development of an integrated approach for the characterization of particulate matter (PM) pollution events in the South of Italy.

Methods

PM₁₀ and PM_2.5 daily samples were collected from June to November 2008 at an urban background site located in Bari (Puglia Region, South of Italy). Meteorological data, particle size distributions and atmospheric dispersion conditions were also monitored in order to provide information concerning the different features of PM sources.

Results

The collected data allowed suggesting four indicators to characterize different PM₁₀ exceedances. PM_2.5/PM₁₀ ratio, natural radioactivity, aerosol maps and back-trajectory analysis and particle distributions were considered in order to evaluate the contribution of local anthropogenic sources and to determine the different origins of intrusive air mass coming from long-range transport, such as African dust outbreaks and aerosol particles from Central and Eastern Europe. The obtained results were confirmed by applying principal component analysis to the number particle concentration dataset and by the chemical characterization of the samples (PM₁₀ and PM_2.5).

Conclusions

The integrated approach for PM study suggested in this paper can be useful to support the air quality managers for the development of cost-effective control strategies and the application of more suitable risk management approaches.     

Windblown Dust Contributes to High PM25 Concentrations

ABSTRACT

The revised National Ambient Air Quality Standards for PM include fine particulate standards based upon mass measurements of PM₂₅. It is possible in arid and semi-arid regions to observe significant coarse mode intrusion in the PM_2.5 measurement. In this work, continuous PM₁₀, PM_2.5, and PM_1.0 were measured during several windblown dust events in Spokane, WA. PM_{2 5} constituted ~30% of the PM₁₀ during the dust event days, compared with ~48% on the non-dusty days preceding the dust events. Both PM₁₀ and PM_2.5 were enhanced during the dust events. However, PM_1.0 was not enhanced during dust storms that originated within the state of Washington. During a dust storm that originated in Asia and impacted Spokane, PM_1.0 was also enhanced, although the Asian dust reached Washington during a period of stagnation and poor dispersion, so that local sources were also contributing to high particulate levels. The “intermodal” region of PM, defined as particles ranging in aerodynamic size from 1.0 to 2.5 um, was found to represent a significant fraction of PM₂₅ (~51%) during windblown dust events, compared with 28% during the non-dusty days before the dust events.     

A study on variations of concentrations of particulate matter with different sizes in Lanzhou,China

Lanzhou is one of the most air-polluted cities in China and in the world, and its primary air pollutant is particulate matter (PM). Different size particulate matter (TSP, PM₁₀, PM_2.5 and PM_1.0) have different sources and affect the environment and human health differently, so it is very important to study the pollutant characteristics of different particles in order to deeply understand the pollution situation of Lanzhou city and establish reasonable preventive countermeasures. TSP, PM₁₀, PM_2.5 and PM_1.0 concentrations were simultaneously measured in Lanzhou to detect the annual and diurnal variations of concentrations of PM with different sizes and possible causes. The main results are as follows: (1) The annual distribution of monthly average concentrations for coarse particles (TSP and PM₁₀) is bimodal with the highest peak in April, which is different from the situation in other cities not affected by sand-dust events. However, the annual distribution for fine particles (PM_2.5 and PM_1.0) is unimodal with the peak in December. This difference between coarse and fine particles indicates that sand-dust events in spring carry much more coarse than fine particles to Lanzhou. This result is supported by the correlation between springtime wind speed and concentrations of PM with different sizes. (2) Under normal conditions (without dust intrusions), the diurnal distribution of coarse particle concentration in Lanzhou is bimodal. However, the distribution is trimodal during dust intrusions in April, with an extra peak in the afternoon. (3) In general, the highest concentration peaks of the diurnal variations for TSP, PM₁₀, PM_2.5 and PM_1.0 occur at about the same time. However, there are obvious differences in the occurrence time of the minimum concentrations among different kinds of PM. The differences in the occurrence time of minima between coarse and fine particles are due to their different diffusion behaviors in the atmospheric boundary layer.     

The impacts of different kinds of dust events on PM10 pollution in northern China

In this study the frequencies of PM₁₀ (as key urban pollutant) in 14 key environmental protection cities in northern China were analyzed. It follows that the PM₁₀ concentration in the high-frequency period is higher with an extent 0.009–0.066 mg m⁻³ than in the low-frequency period of 2001–2002. Further the impacts of three kinds of dust events on the PM₁₀ concentration in four cities (Beijing, Hohhot, Xi’an and Lanzhou) were explored. The results showed that different kinds of dust events have different influences on variation of PM₁₀ concentration in these four cities. In Lanzhou and Hohhot, which are near the source areas of dust events, the contribution degree of these three dust events to the PM₁₀ is: floating dust>dust storm>blowing dust. Whereas, in Beijing and Xi’an situated in dust event passing areas, the mean value of PM₁₀ concentration is higher in blowing dust than in floating dust (no dust storm). In addition, the influences of dust events on PM₁₀ concentration are different in the cities on different dust event paths. In Beijing and Hohhot (on the northern path), the high PM₁₀ concentration is usually caused by blowing dust. But in both Lanzhou and Xi’an (on the western/northwestern path) the high PM₁₀ pollution concentration is usually caused by floating dust.     

Saharan dust contributions to PM10 and TSP levels in Southern and Eastern Spain

The analysis of PM10 and TSP levels recorded in rural areas from Southern and Eastern Spain (1996–1999) shows that most of the PM10 and TSP peak events are simultaneously recorded at monitoring stations up to 1000 km apart. The study of the atmospheric dynamics by back-trajectory analysis and simulations with the SKIRON Forecast System show that these high PM10 and TSP events occur when high-dust Saharan air masses are transported over the Iberian Peninsula. In the January–June period, this dust transport is mainly caused by cyclonic activity over the West or South of Portugal, whereas in the summer period this is induced by anticyclonic activity over the East or Southeast Iberian Peninsula. Most of the Saharan intrusions which exert a major influence on the particulate levels occur from May to September (63%) and in January and October. In rural areas in Northeast Spain, where the PM10 annual mean is around 18 μg PM10 m⁻³, the Saharan dust accounts for 4–7 annual daily exceedances of the forthcoming PM10-EU limit value (50 μg PM10 m⁻³ daily mean). Higher PM10 background levels are recorded in Southern Spain (30 μg PM10 m⁻³ as annual mean for rural areas) and very similar values are recorded in industrial and urban areas. In rural areas in Southern Spain, the Saharan dust events accounts for 10–23 annual daily exceedances of the PM10 limit value, a high number when compared with the forthcoming EU standard, which states that the limit value cannot be exceeded more than 7 days per year. The proportion of Sahara-induced exceedances with respect to the total annual exceedances is discussed for rural, urban and industrial sites in Southern Spain.     

Influence of particulate matter on the air quality situation in a mediterranean island

The objective of this study was to describe the ambient levels of particulate matter (PM) and its influence to air quality situation on the dry Mediterranean island of Cyprus. From October 2002 to August 2003 PM₁₀ and PM_2.5 samples were collected at 31 different sampling sites in Cyprus. In addition, continuous measurements of PM₁₀ were carried out from 2003 to 2007 at a traffic and a rural site. It can be recognised that at all traffic and at some residential and urban background sites, the actual EU limit values have been exceeded. Special events e.g. long-range transport of Sahara dust storms were recorded over urban as well as rural areas in the order of 6–8 events per year, with a major frequency in summer and spring periods. The comparison of the PM₁₀ concentrations in Cyprus cities with values of other European cities demonstrates the PM₁₀ problem in Cyprus, especially in the dry summer season, when no rain is cleaning the air and the dry surfaces. This underlines the necessity of PM abatement strategies.     

Metallic characteristics of PM2.5 and PM2.5-10 for clustered Aeolian Dust Episodes occurred in an extensive fluvial basin during rainy season

Aeolian dust episodes (ADEs) have been an emergency disaster in the Kaoping River Valley during the rainy season (May-September), which can severely deteriorate ambient particulate air quality in the region surrounding the Kaoping River. Thus, this study aims to characterize the metallic fingerprint of Aeolian dust (AD) and investigate the effects of ADEs on ambient particulate air quality along the Kaoping River Valley. Four manual sampling sites adjacent to the riverside were selected to collect fine (PM2.5) and coarse (PM2.5–10) aerosol samples during and after the ADEs in the periods of six events. A total of 13 metallic elements were analyzed using an inductively coupled plasma-atomic emission spectrometer. With metallic elements analysis and nonparametric statistical methods of Wilcoxon rank-sum test and Kruskal-Wallis test, this study successfully derived the metallic indicators of ADEs. The mass ratios of crustal elements (Fe, Ca, or Al) to reference element (Cd) obtained during the ADEs were much higher than those obtained after the ADEs. High mass ratios of Fe/Cd, Ca/Cd, and Al/Cd in PM2.5-10 were observed on the influenced areas of ADEs. Among them, (Fe/Cd)2.5-10 was proven as the best indicator which can be applied to effectively validate the existence of ADEs and evaluate their influences on ambient air quality. Moreover, PM2.5 concentrations during the ADEs were 3-3.6 fold higher than those after the ADEs. PM2.5 should be a contributor to AD, even though the mass ratios of PM2.5/PM10 ranged from 0.05 to 0.20 during the ADEs. Our findings provide valuable information regarding the characteristics of the AD during the ADEs in the Kaoping River.

Implications: Indicators of (Fe/Cd)_2.5-10 are approximately applied to observe the effects of ADEs. Local governments could realize the mechanisms of S- and NW-type aeolian dust episodes (ADEs). They can cause deterioration in different ways for the regional air quality surrounding Kaoping River Valley. Residents who have been living in the influenced areas can take precautions to prevent damage from aeolian dust. Strategies for curbing ADEs must reduce the area of bare lands by artificial measures in the long period of the sunny days during the rainy season. Future research should examine physical conditions of topsoils and other chemical composition in aeolian dust.     

Observed chemical characteristics of long-range transported particles at a marine background site in Korea

Deokjeok Island is located off the west coast of the Korean Peninsula and is a suitable place to monitor the long-range transport of air pollutants from the Asian continent. In addition to pollutants, Asian dust particles are also transported to the island during long-range transport events. Episodic transport of dust and secondary particles was observed during intensive measurements in the spring (March 31-April 11) and fall (October 13-26) of 2009. In this study, the chemical characteristics of long-range-transported particles were investigated based on highly time-resolved ionic measurements with a particle-into-liquid system coupled with an online ion chromatograph (PILS-IC) that simultaneously measures concentrations of cations (Li+, Na , NH4+, K+, Ca2+, Mg2+) and anions (F-, C1-, NO3-, SO42-). The aerosol optical thickness (AOT) distribution retrieved by the modified Bremen Aerosol Retrieval (M-BAER) algorithm from moderate resolution imaging spectroradiometer (MODIS) satellite data confirmed the presence of a thick aerosol plume coming from the Asian continent towards the Korean peninsula. Seven distinctive events involving the long-range transport (LRT) of aerosols were identified and studied, the chemical components of which were strongly related to sector sources. Enrichment of acidic secondary aerosols on mineral dust particles, and even of sea-salt components, during transport was observed in this study. Backward trajectory, chemical analyses, and satellite aerosol retrievals identified two distinct events: a distinctively high [Ca2++Mg2]/[Na+] ratio (>2.0), which was indicative of a preprocessed mineral dust transport event, and a low [Ca2++Mg2+]/[Na+] ratio (<2.0), which was indicative of severe aging of sea-salt components on the processed dust particles. Particulate C1- was depleted by up to 85% in spring and 50% in the fall. A consistent fraction of carbonate replacement (FCR) averaged 0.53 in spring and 0.55 in the fall. Supporting evidences of C1- enrichment on the marine boundary layer prior to a dust front were also found. Supplemental materials are available for this article. Go to the publisher's online edition of the Journal of the Air & Waste Management Association for sector and air mass classifications of clean and LRT cases.     

Evaluation of gas well setback policy in the Marcellus Shale region of Pennsylvania in relation to emissions of fine particulate matter

Shale gas has become an important strategic energy source with considerable potential economic benefits and the potential to reduce greenhouse gas emissions in so far as it displaces coal use. However, there still exist environmental health risks caused by emissions from exploration and production activities. In the United States, states and localities have set different minimum setback policies to reduce the health risks corresponding to the emissions from these locations, but it is unclear whether these policies are sufficient. This study uses a Gaussian plume model to evaluate the probability of exposure exceedance from EPA concentration limits for PM2.5 at various locations around a generic wellsite in the Marcellus shale region. A set of meteorological data monitored at ten different stations across Marcellus shale gas region in Pennsylvania during 2015 serves as an input to this model. Results indicate that even though the current setback distance policy in Pennsylvania (500 ft. or 152.4 m) might be effective in some cases, exposure limit exceedance occurs frequently at this distance with higher than average emission rates and/or greater number of wells per wellpad. Setback distances should be 736 m to ensure compliance with the daily average concentration of PM2.5, and a function of the number of wells to comply with the annual average PM2.5 exposure standard.

Implications: The Marcellus Shale gas is known as a significant source of criteria pollutants and studies show that the current setback distance in Pennsylvania is not adequate to protect the residents from exceeding the established limits. Even an effective setback distance to meet the annual exposure limit may not be adequate to meet the daily limit. The probability of exceeding the annual limit increases with number of wells per site. We use a probabilistic dispersion model to introduce a technical basis to select appropriate setback distances.     

Distant source contributions to PM10 profile evaluated by SOM based cluster analysis of air mass trajectory sets

This paper evaluates the effects of long-range transport patterns of air masses to the regional PM profile in a megacity, Istanbul, Turkey. Five-day hourly backward trajectories were obtained by the HYSPLIT model for selected episodic events in 2008. Self Organizing Maps (SOM), a very powerful classification tool, was used to cluster these trajectories. In total, eight cluster groups were obtained. All of the clusters were evaluated with respect to inhalable particulate matter (PM₁₀) concentrations observed in Istanbul for the arrival times of the trajectories. Istanbul is generally under the effect of trajectories in three clusters (1, 2 and 4) (52% of all pre-selected episodic events), which have higher mean concentration values than the mean value of all the samples. These clusters typically make significant PM contributions to Istanbul's air quality. PM loadings of the trajectories in these clusters were attributed to massive anthropogenic activity over all of Europe and southwestern air flow most likely carrying PM₁₀ atmospheric particles originating from the Saharan Desert and other global dust generation regions located in the northern part of Africa.     

Influence of African dust on the levels of atmospheric particulates in the Canary Islands air quality network

Time series of levels of atmospheric particulate matter (TSP and PM10) were studied at 19 air quality monitoring stations in the islands of Tenerife and Gran Canaria (Canary Islands) during the period 1998–2000. After analysing seasonal variations, attention was focused on the detection of high TSP and PM10 events and on the identification of their natural or anthropogenic origins. Back-trajectory analysis and TOMS-NASA aerosol index as well as satellite imagery (SeaWIFS-NASA) were used to identify three types of African dust outbreaks differing in seasonal occurrence, source origin and impact on TSP/PM10 levels. Mean annual and daily TSP and PM10 levels were compared with the forthcoming limit values of the EU Air Quality Directive EC/30/1999, and the results showed that the annual and daily limit values established for 2010 would only be met at rural stations. PM levels at urban background, urban and industrial sites would exceed the 2010 objectives. Only the levels at the urban-background stations would meet the requirements for 2005 despite the fact that the trade winds result in lower levels of atmospheric pollutants in the Canary Islands than in continental environments. The results highlight the role of African dust contributions when implementing the limit values of the EU directive.     

Influence of major African dust intrusions on the 137Cs and 40K activities in the lower atmosphere at the Island of Tenerife

The influence of two intensive low-altitude atmospheric-dust intrusions on the activity levels of ¹³⁷Cs and ⁴⁰K as well as atmospheric particle matter (PM10) concentrations in the lower atmosphere of the Canary Islands are analysed here. These two events took place at the beginning of January 2002 and March 2004, respectively. 3D atmospheric back-trajectories indicated that the main source of dust material involved in the considered atmospheric intrusions came from NW Africa. A consequence of these dust intrusions was the major increase of PM10 concentrations in the lower atmosphere. Both episodes were characterised by having weekly averages of PM10 concentration surpassing 150 μg m⁻³, higher than the daily PM10 limit value established by the EC/1999/30 directive for PM10 from 2005. Similarly, during these two events, both ¹³⁷Cs and ⁴⁰K activities increased by a factor of 6 and 13 as well as 13 and 14, respectively, over the basal values calculated for each radionuclide and time period (0.59±0.02 and 0.88±0.07 μBq m⁻³ as well as 12±6 and 24±8 μBq m⁻³).     

Food contamination by C20–C50 mineral paraffins from the atmosphere

Most foods from plant origin usually contain 1–10 mg/kg (dry weight) of non-resolved isomeric alkanes in the range of the n-alkanes C₂₀–C₅₀ which are assumed to be residues from mineral oil products (in addition to the natural paraffins). In edible vegetable oils, concentrations may exceed 100 mg/kg. Since it was suspected that this contamination was mostly of environmental origin, particulate matter from air was analysed for the same range of paraffins. In a road tunnel, around 5 μg/m³ of such paraffins were found, corresponding to about 3% of the fine dust (PM10). The composition corresponded to that found in the particulate matter from the exhaust of diesel engines, which in turn largely corresponded to engine (lubricating) oil. In Swiss cities, the C₂₀–C₅₀ mineral paraffins in the PM10 from ambient air amounted to 0.1–1.5 μg/m³ (about 1% of the dust) and seemed to primarily originate from incomplete combustion of heating and diesel oil, lubricating oil, and road tar debris. On the countryside, the concentrations were around 0.03 μg/m³ (0.3% of the dust). Soil contained 0.5–10 mg/kg of these paraffins. The similarity of the molecular weight (volatility) distribution suggests that the food contamination with paraffins, is mostly from the air. A substantial proportion probably consists of lubricating oil. If this hypothesis is confirmed, measures should be investigated to reduce this contamination.     

Implementation of a windblown dust parameterization into MODELS-3/CMAQ: Application to episodic PM events in the US/Mexico border

Windblown dust is known to impede visibility, deteriorate air quality and modify the radiation budget. Arid and semiarid areas with unpaved and unvegetated land cover are particularly prone to windblown dust, which is often attributed to high particulate matter (PM) pollution in such areas. Yet, windblown dust is poorly represented in existing regulatory air quality models. In a study by the authors on modeling episodic high PM events along the US/Mexico border using the state-of-the-art CMAQ/MM5/SMOKE air quality modeling system [Choi, Y.-J., Hyde, P., Fernando, H.J.S., 2006. Modeling of episodic particulate matter events using a 3D air quality model with fine grid: applications to a pair of cities in the US/Mexico border. Atmospheric Environment 40, 5181–5201], some of the observed PM₁₀ NAAQS exceedances were inferred as due to windblown dust, but the modeling system was incapable of dealing with time-dependent episodic dust entrainment during high wind periods. In this paper, a time-dependent entrainment parameterization for windblown dust is implemented in the CMAQ/MM5/SMOKE modeling system with the hope of improving PM predictions. An approach for realizing windblown dust emission flux for each grid cell over the study domain on an hourly basis, which accounts for the influence of factors such as soil moisture content, atmospheric stability and wind speed, is presented in detail. Comparison of model predictions with observational data taken at a pair of US/Mexico border towns shows a clear improvement of model performance upon implementation of the dust emission flux parameterization.     

African dust contributions to mean ambient PM10 mass-levels across the Mediterranean Basin

Data on mass-levels of PM₁₀ measured at regional background sites across the Mediterranean Basin, available from Airbase (European Environmental Agency) and from a few aerosol research sites, are compiled. PM₁₀ levels increase from north to south and west to east of the Basin. These variations are roughly coincident with the PM₁₀ African mineral dust load. However, when subtracting the African dust from mean PM₁₀ levels using a consistent methodology, the PM₁₀ background levels are still 5–10 μg m^?3 higher in the Eastern Basin (EMB) when compared with those in the Western (WMB), mainly due to the higher anthropogenic and sea spray loads.As regards for the seasonal trends, these are largely driven by the occurrence of African dust events, resulting in a spring-early summer maximum over the EMB, and a clear summer maximum in the WMB, although in this later region the recirculations of aged air masses play an important role. Furthermore, a marked seasonal trend is still evident when subtracting the African dust load. This is characterised by a high summer maximum (driven by low precipitation, high insolation) and a winter minimum (intense synoptic winds).Important inter-annual variations in the dust contribution are detected, more evident in the southern sites. These differences are generally associated with the occurrence of extreme dust events. Generally, the years with higher dust contributions over the EMB correspond with lower contributions over the WMB, and vice versa.The characterization of individual particles, collected in both basins during African dust events, by scanning electron microscopy reveals only slight differences between them. This fact probably reflects the high degree of mixture of mineral dust from different sources before the transport towards the receptor sites.     

Windblown dust contributes to high PM2.5 concentrations

The revised National Ambient Air Quality Standards for PM include fine particulate standards based upon mass measurements of PM2.5. It is possible in arid and semi-arid regions to observe significant coarse mode intrusion in the PM2.5 measurement. In this work, continuous PM10, PM2.5, and PM1.0 were measured during several windblown dust events in Spokane, WA. PM2.5 constituted approximately 30% of the PM10 during the dust event days, compared with approximately 48% on the non-dusty days preceding the dust events. Both PM10 and PM2.5 were enhanced during the dust events. However, PM1.0 was not enhanced during dust storms that originated within the state of Washington. During a dust storm that originated in Asia and impacted Spokane, PM1.0 was also enhanced, although the Asian dust reached Washington during a period of stagnation and poor dispersion, so that local sources were also contributing to high particulate levels. The "intermodal" region of PM, defined as particles ranging in aerodynamic size from 1.0 to 2.5 microns, was found to represent a significant fraction of PM2.5 (approximately 51%) during windblown dust events, compared with 28% during the non-dusty days before the dust events.