Removal of a cationic dye from aqueous solutions by adsorption onto bentonite clay

The ability of bentonite to remove malachite green from aqueous solutions has been studied for different adsorbate concentrations by varying the amount of adsorbent, temperature, pH and shaking time. Maximum adsorption of the dye, i.e. >90% has been achieved in aqueous solutions using 0.05 g of bentonite at a pH of 9. Thermodynamic parameters such as ΔH°, ΔS° and ΔG° were calculated from the slope and intercept of the linear plots of ln K_D against 1/T. Analysis of adsorption results obtained at 298, 308, 318 and 328 K showed that the adsorption pattern on bentonite seems to follow the Langmuir, Freundlih and D–R isotherms. The temperature increase reduces adsorption capacity by bentonite, due to the enhancement of the desorption step in the mechanism. The numerical values of sorption free energy (E_a) of 1.00–1.12 kJ mol⁻¹ indicated physical adsorption. The kinetic data indicated an intraparticle diffusion process with sorption being first order. The rate constant k was 0.526 min⁻¹. The concentration of malachite green oxalate was measured before and after adsorption by using UV–Vis spectrophotometer.     

Selective adsorption of phenanthrene dissolved in surfactant solution using activated carbon

Selective adsorption of a hazardous hydrophobic organic compound (HOC) by activated carbon as a means of recovering surfactants after a soil washing process was investigated. As a model system, phenanthrene was selected as a representative HOC and Triton X-100 as a nonionic surfactant. Three activated carbons that differed in size (Darco 20–40 (D20), 12–20 (D12) and 4–12 (D4) mesh sizes) were used in adsorption experiments. Adsorption of surfactant onto activated carbon showed a constant maximum above the critical micelle concentration, which were 0.30, 0.23, 0.15 g g⁻¹ for D20, D12, and D4, respectively. Selectivity for phenanthrene to Triton X-100 was much higher than 1 over a wide range of activated carbon doses (0–6 g l⁻¹) and initial phenanthrene concentrations (10–110 mg l⁻¹). Selectivity generally increased with decreasing particle size, increasing activated carbon dose, and decreasing initial concentration of phenanthrene. The highest selectivity was 74.9, 57.3, and 38.3 for D20, D12, and D4, respectively, at the initial conditions of 10 mg l⁻¹ phenanthrene, 5 g l⁻¹ Triton X-100 and 1 g l⁻¹ activated carbon. In the case of D20 at the same conditions, 86.5% of the initial phenanthrene was removed by sorption and 93.6% of the initial Triton X-100 remained in the solution following the selective adsorption process. The results suggest that the selective adsorption by activated carbon is a good alternative for surfactant recovery in a soil washing process.     

Screening 31 endocrine-disrupting pesticides in water and surface sediment samples from Beijing Guanting reservoir

For screening 31 potential or suspected endocrine-disrupting pesticides in water and surface sediments, a multiresidue analysis method based on gas chromatography with electron capture detection (GC/ECD) was developed. Solid phase extraction (SPE) technology with Oasis^® HLB cartridge was also applied in sample extraction. The relevant mean recoveries were 70–103% and 71–103% for water and sediment, respectively. Relative standard deviations (RSD) are 2.0–7.0%, 4.0–8.0% for water and sediment, respectively. Thirty one pesticides (-HCH, β-HCH, γ-HCH, δ-HCH, hexachlorobenzene (HCB), aldrin, heptachlor, endosulfan I & II, p,p′-DDD, o,p′-DDT, p,p′-DDT, p,p′-DDE, endrin aldehyde, endosulfan sulphate, methoxychlor, hepachlor epoxide, -chlordane, γ-chlordane, dieldrin, endrin, dicofol, acetochlor, alachlor, metolachlor, chlorpyriphos, nitrofen, trifluralin, cypermethrin, fenvalerate, deltamethrin) in water and surface sediment samples from Beijing Guanting reservoir were analyzed. Concentrations of pesticides ranged from 7.59 to 36.0 ng g⁻¹ on a dry wt. basis for sediment samples, from 279.3 to 2740 ng l⁻¹ for pore waters and from 48.8 to 890 ng l⁻¹ for water samples, respectively, with a mean concentration of 10.7 ng g⁻¹ in sediment, 735 ng l⁻¹ in pore water and 295 ng l⁻¹ in water, respectively. The data obtained provides information on the levels and sources of endocrine-disrupting pesticides in Guanting reservoir. These results underscore the need to improved environmental protection measures in order to reduce the exposure of the population and aquatic biota to these endocrine-disrupting compounds.     

Octyl and nonylphenol ethoxylates and carboxylates in wastewater and sediments by liquid chromatography/tandem mass spectrometry

This work presents an LC–MS–MS-based method for the quantitation of nonylphenol ethoxylates (NPEOs) and octylphenol ethoxylates (OPEOs) in water, sediment, and suspended particulate matter, and three of their carboxylated derivatives in water. The alkylphenol ethoxylates (APEOs) were analyzed using isotope dilution mass spectrometry with [¹³C₆]-labeled analogues, whereas the carboxylated derivatives were determined by external standard quantitation followed by confirmation using standard additions. The method was used to study APEO’s behavior in a wastewater treatment plant (WWTP), where total dissolved NP0-16EO concentration was reduced by approximately 99% from influent (390 μg l⁻¹) to final effluent (4 μg l⁻¹), and total OP0-5EO concentration decreased by 94% from 3.1 to 0.2 μg l⁻¹. In contrast, the carboxylated derivatives were formed during the process with NP0-1EC concentrations increasing from 1.4 to 24 μg l⁻¹. Short-chain APEOs were present in higher proportions in particulate matter, presumably due to greater affinity for solids compared to the long-chain homologues. NP (0.49 μg l⁻¹) and NP0-1EC (4.8 μg l⁻¹) were the only APEO-related compounds detected in a surface water sample from a WWTP-impacted estuary; implying that 90% of the mass was in the form of carboxylated derivatives. Sediment analysis showed nonylphenol to be the single most abundant compound in sediments from the Baltimore Harbor area, where differences in homologue distribution suggested the presence of treated effluent in some of the sites and non-treated sources in the rest.     

Fate of cancerostatic platinum compounds in biological wastewater treatment of hospital effluents

The present work focuses on the fate of two cancerostatic platinum compounds (CPC), cisplatin and carboplatin, as well as of two inorganic platinum compounds, [PtCl₄]²⁻ and [PtCl₆]²⁻ in biological wastewater treatment. Laboratory experiments modelling adsorption of these compounds onto activated sludge showed promising specific adsorption coefficients K_D and K_OC and Freundlich adsorption isotherms. However, the adsorption properties of the investigated substances were differing significantly. Adsorption decreased following the order cisplatin > [PtCl₆]²⁻ > [PtCl₄]²⁻ > carboplatin. Log K_D-values were ranging from 2.5 to 4.3 , log K_OC from 3.0 to 4.7.

A pilot membrane bioreactor system (MBR) was installed in a hospital in Vienna and fed with wastewater from the oncologic in-patient treatment ward to investigate CPC-adsorption in a sewage treatment plant. During three monitoring periods Pt-concentrations were measured in the influent (3–250 μg l⁻¹ Pt) and the effluent (2–150 μg l⁻¹ Pt) of the treatment plant using ICP-MS. The monitoring periods (duration 30 d) revealed elimination efficiencies between 51% and 63% based on averaged weekly input–output budgets. The derived log K_D-values and log K_OC-values ranged from 2.4 to 4.8 and from 2.8 to 5.3, respectively. Species analysis using HPLC-ICP-MS proofed that mainly carboplatin was present as intact drug in the influent and – due to low log K_D – in the effluent of the MBR.     

Study on the fluorescence characteristics of bromadiolone in aqueous and organized media and application in analysis

The fluorescence spectroscopic behavior of bromadiolone (anticoagulant rodenticide), a substituted 4-hydroxycoumarin derivative, was investigated in water and in organized media like micelles and cyclodextrins. A detailed study on various photophysical parameters like fluorescence intensity (I_F), quantum yield (), lifetime (τ) and steady state fluorescence anisotropy (r) of bromadiolone in aqueous and in organized media was carried out. Bromadiolone in aqueous solution was observed to be in an aggregated state, thereby showing weak emission due to self-quenching. Marked enhancement of fluorescence intensity was observed in organized media like micelles and β-cyclodextrin. A preliminary investigation has been done to find out whether this enhancement of fluorescence can be used to develop a sensitive analytical method for determination of bromadialone in aqueous media. A linear relationship between the fluorescence intensity and concentration of bromadiolone was observed in the range of 0.15–7.9 μg ml⁻¹ in cetyltrimethylammonium bromide (CTAB) and 0.5–26.4 μg ml⁻¹ in β-cyclodextrin medium. The lower detection limit was found to be 37 ng ml⁻¹ in presence of CTAB and 23 ng ml⁻¹ in β-cyclodextrin. Comparison with 4-hydroxycoumarin, an unsubstituted analogue, was made.     

Kinetic studies of adsorption of thiocyanate onto ZnCl2 activated carbon from coir pith, an agricultural solid waste

The adsorption of thiocyanate onto ZnCl₂ activated carbon developed from coir pith was investigated to assess the possible use of this adsorbent. The influence of various parameters such as agitation time, thiocyanate concentration, adsorbent dose, pH and temperature has been studied. Adsorption followed second-order rate kinetics. Two theoretical adsorption isotherms, namely, Langmuir and Freundlich were used to describe the experimental results. The Langmuir adsorption capacity (Q₀) was found to be 16.2 mg g⁻¹ of the adsorbent. The per cent adsorption was maximum in the pH range 3.0–7.0. pH effect and desorption studies showed that ion exchange and chemisorption mechanism are involved in the adsorption process. Thermodynamic parameters such as ΔG⁰, ΔH⁰ and ΔS⁰ for the adsorption were evaluated. The negative values of ΔH⁰ confirm the exothermic nature of adsorption. Effects of foreign ions on the adsorption of thiocyanate have been investigated. Removal of thiocyanate from ground water was also tested.     

Distribution of pesticides and heavy metals in trophic chain

Determination of triazines herbicides (atrazine and simazine) by high performance liquid chromatography (HPLC) in samples of trophic chain were worked out. Determination limits of 0.5 μg g⁻¹ for atrazine, 0.8 μg g⁻¹ for simazine with pesticides recovery of 70–77% in trophic chain samples were obtained. The content of simazine in soils was in range 1.72–57.89 μg g⁻¹, in grass 5–88 μg g⁻¹, in milk 2.32–15.29 μg g⁻¹, in cereals 10.98–387 μg g⁻¹, in eggs 30.14–59.48 μg g⁻¹, for fruits: 2.45–6.19 μg g⁻¹. The content of atrazine in soils was in range 0.69–19.59 μg g⁻¹, in grass 7.85–23.85 μg g⁻¹, in cereals 1.88–43.08 μg g⁻¹. Cadmium, lead and zinc were determined by inductively coupled plasma atomic emission spectrometry (ICP-AES) in the same samples as atrazine and simazine. Determination limits for cadmium 5 × 10⁻³ μg g⁻¹, for lead 1 × 10⁻² μg g⁻¹, and for zinc 0.2 × 10⁻³ μg g⁻¹, were obtained. The content of cadmium in soil was in range 0.13–5.89 μg g⁻¹, in grass 114–627.72 × 10⁻³ μg g⁻¹, in milk 8.88–61.88 × 10⁻³ μg g⁻¹, in cereals 0.20–0.31 μg g⁻¹, in eggs 0.11–0.15 μg g⁻¹, in fruits 0.23–0.59 μg g⁻¹. The content of lead in soils was in range 0.57–151.50 μg g⁻¹, in grass 0.16–136.57 μg g⁻¹, in milk 1.16–3.74 μg g⁻¹, in cereals 1.05–5.47 μg g⁻¹, in eggs 5.79–55.87 μg g⁻¹, in fruits 21.00–87.36 μg g⁻¹. Zinc content in soil was in range 9.15–424.5 μg g⁻¹, in grass 35.20–55.87 μg g⁻¹, in milk 20.00–34.38 μg g⁻¹, in cereals 14.94–28.78 μg g⁻¹, in eggs 15.67–32.01 μg g⁻¹, in fruits 14.94–18.88 μg g⁻¹.

Described below extraction and mineralization methods for particular trophic chains allowed to determine of atrazine, simazine, cadmium, lead and zinc with good repeatability and precision. Emphasis was focused on liquid–liquid extraction and solid-phase extraction of atrazine and simazine from analysed materials, as well as, on monitoring the content of herbicides and metals in soil and along trophic chain. Higher concentration of pesticides in samples from west region of Poland in comparison to that of east region is likely related to common applying them in Western Europe in relation to East Europe. The content of metals strongly depends on samples origin (industry area, vicinity of motorways).     

The role of humic substances in chromium sorption onto natural organic matter (peat)

To elucidate mechanisms of Cr³⁺ sorption onto the unaltered solid natural organic matter, the comparative studies of this ion binding from a solution at pH 4.0 onto three selected particle size fractions: 2000–1000 μm, 630–200 μm and 63–20 μm of markedly different HS content and structure, separated by a wet sieving from an overall sample of peat (Brushwood Peat Humus) were carried out. Comparable patterns of COOH groups and CEC_t confirmed that for cation exchange capacity were responsible mainly cations connected with COO⁻ functional groups. It was though found that aliphatic acids in the solid state did not take part in Cr³⁺ binding, thus the finest studied fraction 63–20 μm of the highest contents of functional groups showed the lowest sorption capacity for Cr³⁺, while similar patterns of sorbed Cr³⁺, soluble HS content and base CEC₀ indicated that these parameters were directly interrelated. The base ion exchange processes determined by CEC₀ (with Ca²⁺ as a predominant exchangeable cation) appeared to be not the major mechanisms responsible for Cr³⁺ sorption. For this metal, strong binding to insoluble large molecular weight organic pool two- to threefold prevailed over the ion exchange processes. Very low acid desorption indicated generally low mobility of Cr³⁺-organic compounds.     

Isoprene emission from tropical trees in Okinawa Island, Japan

This study surveyed isoprene emission from 42 indigenous and exotic tropical trees in subtropic Okinawa, Japan. Of the 42 trees studied, 4 emitted isoprene at a rate in excess of 20 μg g⁻¹ h⁻¹, and 28 showed the rates of 1–10 μg g⁻¹ h⁻¹. The remainder emitted less than 1 μg g⁻¹ h⁻¹. The majority of trees in this study may therefore fall within the lower emitting species. However, species in Moraceae that is indigenous in Okinawa emitted isoprene at relatively higher rates with an average of 14.2 μg g⁻¹ h⁻¹. The highest emission rate of 107.1 μg g⁻¹ h⁻¹ for Ficus virgata yielded the area basis rate of 47.4 nmol m⁻² s⁻¹, which is almost equivalent to the rate of high emitting species. Furthermore, a linear relationship between light intensity and isoprene emission was noted with Ficus virgata up to 1700 μmol m⁻² s⁻¹. These findings may show the potential importance of subtropical areas as sources of isoprene to the atmosphere.     

Determination of 4-tert-octylphenol, 4-nonylphenol and bisphenol A in surface waters from the Haihe River in Tianjin by gas chromatography-mass spectrometry with selected ion monitoring

The estrogenic pollutants 4-tert-octylphenol (OP), 4-nonylphenol (NP) and bisphenol A (BPA) were determined in surface water samples from the Haihe River, Tianjin, China. The analytes were extracted and concentrated from 300 ml acidified water samples by liquid–liquid extractions using dichloromethane, derivatized with trifluoroacetic anhydride, and quantified by gas chromatography–mass spectrometry (GC–MS) with selected ion monitoring (SIM). Among the samples collected from 14 sampling sites, only one sample was found to have a relatively high concentration of BPA (8.30 μg l⁻¹) and NP (0.55 μg l⁻¹). The concentrations of OP, NP and BPA in the other samples were in the range of 18.0–20.2, 106–296 and 19.1–106 ng l⁻¹, respectively. Recoveries for OP, NP and BPA in the spiked water samples were all over 80%.     

Assessment of toxicity of a glyphosate-based formulation using bacterial systems in lake water

A new Aeromonas bioassay is described to assess the potential harmful effects of the glyphosate-based herbicide, Roundup^®, in the Albufera lake, a protected area near Valencia. Viability markers as membrane integrity, culturability and β-galactosidase production of Aeromonas caviae were studied to determine the influence of the herbicide in the bacterial cells. Data from the multifactor analysis of variance test showed no significant differences (P > 0.05) between A. caviae counts of viability markers at the studied concentrations (0, 50 and 100 mg l⁻¹ of glyphosate).

The effects of Roundup^® on microbial biota present in the lake were assessed by measuring the number of indigenous mesophilic Aeromonas in presence of different amounts of the herbicide at 0, 50 and 100 mg l⁻¹ of glyphosate. In samples containing 50 and 100 mg l⁻¹ of glyphosate a significant (P < 0.05) increase in Aeromonas spp. counts and accompanying flora was observed.

The acute toxicity of Roundup^® and of Roundup^® diluted with Albufera lake water to Microtox^® luminescent bacterium (Vibrio fischeri) also was determined. The EC₅₀ values obtained were 36.4 mg l⁻¹ and 64.0 mg l⁻¹ of glyphosate respectively. The acidity (pH 4.5) of the herbicide formulation was the responsible of the observed toxicity.     

UV-H2O2 based AOP and its integration with biological activated carbon treatment for DBP reduction in drinking water

The presence of disinfection byproducts (DBPs) such as trihalomethanes (THMs) and haloacetic acids (HAAs) in drinking water is of great concern due to their adverse effects on human health. Emerging regulation limiting the concentration of DBPs in drinking water has increased demands for technologies and processes which reduce the formation of DBPs in drinking water. In this study, UV-H₂O₂ based advance oxidation process (AOP) was used to treat raw surface water. Experiments were conducted using low pressure mercury vapor UV lamps in collimated beam and flow-through annular photoreactors. The effect of UV fluence (0–3500 mJ cm⁻²) and hydrogen peroxide concentration (0–23 mg l⁻¹) in reducing the concentration of THMs and HAAs was examined. The UV-H₂O₂ AOP was then coupled with a downstream biological activated carbon (BAC) treatment to assess the synergetic benefits of combining the two treatments. It was observed that UV-H₂O₂ AOP was only effective at reducing DBPs at UV fluences of more than 1000 mJ cm⁻²and initial H₂O₂ concentrations of about or greater than 23 mg l⁻¹. However, the combined AOP–BAC treatment showed significant reductions of 43%, 52%, and 59% relative to untreated raw water for DBPs, TOC, and UV₂₅₄, respectively.     

Efficient removal and mechanisms of water soluble aromatic contaminants by a reduced-charge bentonite modified with benzyltrimethylammonium cation

A novel strategy utilizing the phenyls interaction and the hydrophobic affinity of available siloxane surface in the interlayer of bentonite was proposed to improve the sorption capabilities of organobentonites for water soluble aromatic contaminants. A unique organobentonite (65BTMA) was synthesized by intercalating benzyltrimethylammonium cation (BTMA⁺) into the interlayer of a reduced-charge bentonite with cation exchange capacity (CEC) of 65 cmol kg⁻¹. Phenol, aniline and toluene were used as model compounds of water soluble aromatic contaminants. Their respective removal efficiencies by 65BTMA were achieved at 83.3%, 89.2% and 97.3% at the initial concentration of 20 mg l⁻¹. To reveal the sorption mechanism, sorption characteristics of aromatic contaminants to 65BTMA were compared with that of aliphatic contaminants in similar molecular size. And various organobentonites were prepared by combining TMA⁺ (tetramethylammonium), BTMA⁺, HTMA⁺ (heptyltrimethylammonium) and CTMA⁺ (cetyltrimethylammonium) with two bentonites (CEC = 108 and 65 cmol kg⁻¹). To 65BTMA, sorption magnitudes of aromatic contaminants were much greater than that of aliphatic compounds with similar size; and dramatically higher than those to other organobentonites at low pollutant concentrations. These observations revealed that the strong phenyls interactions contributed significantly to sorb the aqueous soluble aromatic contaminants to 65BTMA (>90%), and which favored to design uniquely powerful sorbents.     

Utilization and degradation of imazaquin by a naturally occurring isolate of Arthrobacter crystallopoietes

A species of bacteria that is capable of utilizing imazaquin as the sole carbon source was isolated from soil with repeated imazaquin applications, and was identified as Arthrobacter crystallopoietes (designated as strain “WWX-1”). This isolate degrades imazaquin as high as 200 μg ml⁻¹, and the estimated dissipation half-lives increased from 1.51 d for the treatment at 50 μg ml⁻¹ to 4.75 d for 200 μg ml⁻¹. Optimal growth of WWX-1 in mineral salt medium with 50 μg ml⁻¹ imazaquin was obtained at 35 °C and a pH of 5.0. Growth of WWX-1 was also observed in mineral salt medium with the addition of other imidazolinone herbicides such as imazethapyr and imazapyr, but not with different classes of herbicides such as metsulfuron-methyl. Two imazaquin metabolites were detected, and spectral analysis with HPLC–MS, ¹H NMR, and IR revealed one metabolite with a molecular weight (MW) of 199 as quinoline-2,3-dicarboxylic anhydride. We propose that A. crystallopoietes (WWX-1) could serve as an efficient biodegradation system for remediation of water and soils that are heavily contaminated with imazaquin or other structurally similar chemicals.     

Determination and distribution characteristics of degradation products of nonylphenol polyethoxylates in the rivers of Taiwan

Concentrations of degradation products of nonylphenol polyethoxylates (NPEOs) were analyzed in river water samples in order to determine the distribution characteristic of these alkylphenolic compounds in 18 major rivers of Taiwan. The degradation products of NPEOs were detected in all river samples, with the dicarboxylates alkylphenolic degradation products (CAPEC) being detected most frequently and at the highest concentrations. Concentrations of NP and NP1EO in rivers ranged from n.d. to 5.1 μg l⁻¹ and n.d. to 0.5 μg l⁻¹, respectively. The total concentrations of shortened carboxylates (i.e., NP1EC + NP2EC + NP3EC) and dicarboxylates alkylphenolic degradation products (CAP1EC + CAP2EC) ranged from n.d. to 63.6 μg l⁻¹ and n.d. to 94.6 μg l⁻¹, respectively. Concentrations of NP2EC, NP3EC and all CAPEC residues were determined semi-quantitatively by comparing with the internal standard. Significantly higher concentrations of CAPEC residues were detected in the river waters as compared to those of NP, NP1EO and NPEC degradation products and the average proportions of these compounds in the samples of the rivers were as follows: NP + NP1EO was 5 ± 2.5%, total NPEC was 25 ± 12%, and total CAPEC was 70 ± 12%. The high concentration ratios of CAPEC/NPEC illustrate that aerobic biodegradation plays a main route in the fate of NPEO in the rivers of Taiwan.     

The use of physiological characteristics for comparison of organic compounds phytotoxicity

The influence of intact (FLT) and photomodified (phFLT) fluoranthene (0.05, 0.5 and 5 μmol l⁻¹) and herbicide Basagran (5, 20, 35 and 50 nmol l⁻¹) on the germination, growth of seedlings and photosynthetic processes in pea plants (Pisum sativum L., cv. Garde) was investigated. The germination was significantly inhibited already by the lowest concentration (0.05 μmol l⁻¹) of FLT and phFLT, while Basagran caused inhibition only in higher concentrations (35 and 50 nmol l⁻¹). The growth of roots was significantly inhibited by higher concentration 5 μmol l⁻¹ of both FLT and phFLT and the shoot of seedlings was significantly influenced only by photomodified form. The length of root and shoot was inhibited already by concentration 5 nmol l⁻¹ of Basagran. Organic compounds applied on chloroplasts suspension influenced primary photochemical processes of photosynthesis. In chlorophyll fluorescence parameters, the significant increase of F₀ values and the decrease of F_V/F_M and Φ_II values by application of FLT (0.5 and 5 μmol l⁻¹) and phFLT (0.05, 0.5 and 5 μmol l⁻¹) was recorded. The maximum capacity of PSII (F_V/F_M) was influenced by the highest (50 nmol l⁻¹) and the effective quantum yield of PSII (Φ_II) already by the lowest (5 nmol l⁻¹) concentration of Basagran. Hill reaction activity decreased and was significantly inhibited by higher concentration (0.5 and 5 μmol l⁻¹) of FLT and phFLT and already by the lowest concentration (5 nmol l⁻¹) of Basagran.     

Organochlorinated pesticides in sediments from the Lake Albufera of Valencia (Spain)

Bottom sediment samples from 121 sites of the Lake Albufera of Valencia were analyzed. Dieldrin, endrin, heptachlor and op′-DDT were not detected (<0.01 ng g⁻¹) in 88–93% of the sites. Aldrin and HCB concentration ranges were between <0.01 and 0.1 ng g⁻¹ in 86% and 94% of the sites, respectively. Heptachlor-epoxide and lindane 95% confidence intervals were 0.2–0.5 and 0.06–0.12, respectively. The greatest average concentration corresponds to pp′-DDE, pp′-DDD and pp′-DDT. The sum of six isomers and derivatives of the DDT average concentration reaches 2.1 ng g⁻¹, as opposed to 2.7 ng g⁻¹ for the sum of 13 pesticides considered. In the site with a major contamination, 27.0 ng g⁻¹ of pp′-DDD and 12.8 ng g⁻¹ of pp′-DDT were accumulated. The DDE:DDT proportion average was 0.37, indicating an aged DDT contamination. Concentrations of pesticides in sediments were compared to three sediment quality guidelines, and indicated that a low biological effects level can be expected in either sediments or aquatic organisms.     

Monoterpene emissions and carbonyl compound air concentrations during the blooming period of rape (Brassica napus)

An increasing percentage of agricultural land in Germany is used for oil seed plants. Hence, rape has become an important agricultural plant (in Saxony 1998: 12% of the farmland) in the recent years. During flowering of rape along with intensive radiation and high temperatures, a higher production and emission of biogenic VOC was observed. The emissions of terpenes were determined and more importantly, high concentrations of organic carbonyl compounds were observed during this field experiment. All measurements of interest have been carried out during two selected days with optimal weather conditions. It is found that the origin or the mechanism of formation of different group of compounds had strong influence on the day to day variation of their concentrations. The emission flux of terpenes from flowering rape plants was determined to be 16–32 μg h⁻¹ m⁻² (30–60 ng h⁻¹ per g dry plant––540–1080 ng h⁻¹ per plant), in total. Limonene, -thujene and sabinene were the most important compounds (about 60% of total terpenes). For limonene and sabinene reference emission rates (M_S) and temperature coefficients were determined: β_limonene=0.108 K⁻¹ and M_S=14.57 μg h⁻¹ m⁻²; β_sabinene=0.095 K⁻¹ and M_S=5.39 μg h⁻¹ m⁻².

The detected carbonyl compound concentrations were unexpectedly high (maximum formaldehyde concentration was 18.1 ppbv and 3.4 ppbv for butyraldehyde) for an open field. Possible reasons for these concentrations are the combination of primary emission from the plants induced by high temperature and high ozone stress, the secondary formation from biogenically and advected anthropogenically emitted VOC at high radiation intensities and furthered by the low wind speeds at this time.     

Influence of water hardness on the bioavailability and toxicity of linear alkylbenzene sulphonate (LAS)

In the present work, the influence of Ca²⁺ concentration on the toxicity of single cut linear alkylbenzene sulfonate (LAS) homologues was studied. Precipitation boundary diagrams for each homologue were obtained, indicating turbid and clear zones depending on the LAS and Ca²⁺ concentrations. The separation between transparent and turbid zones is given by the so-called precipitation line. LAS toxicity to Daphnia magna was determined at concentrations close to this precipitation line. It was observed that when Ca(LAS)₂ precipitation progresses, LAS bioavailability decreases for test animals, and the toxicity diminishes even at high nominal LAS concentrations. According to the “free ion activity model” (FIAM), the toxicity of a given chemical compound is mainly due to the ionic species (Ca²⁺–LAS⁻) and not due to the precipitated molecule, Ca(LAS)₂. The significance of the present study is in connection with the assessment of LAS sorption/precipitation studies in soils and sediments, where in situ toxicity is strongly influenced by Ca²⁺/Mg²⁺ ions, according to the results presented in this work.