大尺寸大孔径TiO2/SiO2光催化剂的制备及甲醛去除研究

以大孔径SiO2为载体，通过钛酸丁酯溶液的浸渍、原位水解以及高温煅烧制备出大尺寸、大孔径的TiO2/SiO2光催化剂。利用自制空气净化装置对室内甲醛的清除进行研究，分别考察了TiO2的百分含量、紫外光光强、温度、湿度和空气流量等不同条件下TiO2/SiO2光催化剂对除去甲醛效率的影响。结果表明，反应温度从10～50℃依...     

TiO2光催化涂料的制备及其降解甲醛研究

自制TiO2光催化涂料，重点对所制备的涂料在室内进行降解甲醛研究，考察了在不同分散剂、不同光催化剂以及不同甲醛初始浓度、不同光源、不同温度和不同湿度等环境因素下涂料对甲醛降解率的影响。结果表明，选用聚丙烯酸钠离子型分散剂，铜金属掺杂TiO2光催化剂制备的光催化涂料对甲醛降解率达80％以上且具有良好的耐久性，在室温（20℃左右）湿度50％日光灯照射下，甲醛初始浓度5μL时效果最佳。     

TiO2光催化降解水中苯酚的试验研究

以悬浆态TiO2为光催化剂，在紫外光催化反应器中，进行了苯酚溶液的动态光催化降解性能的研究，考察了TiO2用量、TiO2焙烧温度、溶液pH值以及循环流量对苯酚光催化降解的影响。结果表明，TiO2用量1．0g／L，TiO2焙烧温度450℃，循环流量20L／h，紫外光照反应5h，苯酚去除率为71．2％。     

V/Ce共掺杂TiO2光催化降解甲醛的实验研究

采用溶胶-凝胶法制备了不掺杂、V掺杂、Ce掺杂、V/Ce共掺杂纳米TiO2光催化剂,并将其分别负载于瓷砖上,利用X射线衍射分析（XRD）和扫描电镜分析（SEM）技术对薄膜样品的结构和形貌进行了表征。通过对甲醛的降解实验评价光催化剂的光催化活性。实验结果表明,光催化剂的负载量、共掺杂离子的掺杂量、掺杂配比、煅烧温度影响纳米TiO2的光催化活性。V/Ce共掺杂TiO2光催化剂产生了协同效应,其光催化活性优于纯TiO2和单掺杂TiO2样品。     

Fe/Si/TiO2三元复合光催化剂的性能研究

用溶胶-凝胶法制备了Fe/Si/TiO2三元复合光催化剂,利用X射线衍射(XRD)和紫外-可见漫反射光谱(DRS)对样品进行了分析表征,并以甲基橙为模拟污染物,考察了其光催化活性.结果表明,Fe/Si/TiO2三元复合光催化剂与TiO2相比,光催化活性明显提高;当煅烧温度为900℃、添加Fe的摩尔分数为0.050%时,光催化活性最佳.     

纳米TiO2/活性炭复合光催化剂的制备及其对甲醛气体降解

研究了纳米TiO2/活性炭复合光催化剂对空气中典型污染气体甲醛的光催化降解特性。采用扫描电镜（SEM）表征复合催化剂的表面特征。结果显示,经改性后的纳米TiO2在复合催化剂表面分布均匀,呈球状。对甲醛气体的降解实验显示TiO2负载量为1%时对甲醛的去除效果最好,6 h去除率为61.7%。结果显示复合催化剂把甲醛气体分解成CO2,可以直接排空,无二次污染。     

纳米TiO2/活性炭复合光催化剂的制备及其对甲醛气体降解

研究了纳米TiO2/活性炭复合光催化剂对空气中典型污染气体甲醛的光催化降解特性。采用扫描电镜(SEM)表征复合催化剂的表面特征。结果显示,经改性后的纳米TiO2在复合催化剂表面分布均匀,呈球状。对甲醛气体的降解实验显示TiO2负载量为1%时对甲醛的去除效果最好,6 h去除率为61.7%。结果显示复合催化剂把甲醛气体分解成CO2,可以直接排空,无二次污染。     

SO_4~（2-）/TiO_2光催化降解苯酚

以工业硫酸氧钛为原料水解制得SO42-/TiO2光催化剂,并以苯酚为目标降解物,考察了SO24-/TiO2的光催化性能。结果表明：随着SO42-/TiO2制备过程中焙烧温度的升高,其光催化活性逐渐增加,650℃焙烧获得的SO24-/TiO2的光催化活性最好,此后再升高温度会因催化剂中硫的挥发而下降;在确定苯酚原液初始浓度为50 mg/L条件下,SO42-/TiO2的光催化降解苯酚的最佳工艺条件为反应时间2 h、苯酚pH为7、催化剂用量1 g/L。XRD、SEM和FTIR的分析结果显示实验温度下制得的SO42-/TiO2均为锐钛型TiO2;其间掺杂的SO24-在TiO2表面分散性较好,没有聚集成大的颗粒;红外分析的结果初步判定低温（〈550℃）焙烧制得的催化剂SO42-在TiO2表面是螯合双配位吸附,高温焙烧时（〉550℃）SO42-在TiO2表面是桥式配位吸附。     

SO2-4/TiO2光催化降解苯酚

以工业硫酸氧钛为原料水解制得SO42-/TiO2光催化剂,并以苯酚为目标降解物,考察了SO24-/TiO2的光催化性能。结果表明:随着SO42-/TiO2制备过程中焙烧温度的升高,其光催化活性逐渐增加,650℃焙烧获得的SO24-/TiO2的光催化活性最好,此后再升高温度会因催化剂中硫的挥发而下降;在确定苯酚原液初始浓度为50 mg/L条件下,SO42-/TiO2的光催化降解苯酚的最佳工艺条件为反应时间2 h、苯酚pH为7、催化剂用量1 g/L。XRD、SEM和FTIR的分析结果显示实验温度下制得的SO42-/TiO2均为锐钛型TiO2;其间掺杂的SO24-在TiO2表面分散性较好,没有聚集成大的颗粒;红外分析的结果初步判定低温(<550℃)焙烧制得的催化剂SO42-在TiO2表面是螯合双配位吸附,高温焙烧时(>550℃)SO42-在TiO2表面是桥式配位吸附。     

Fe/TiO2光催化降解水溶液中的4-氯苯酚

以TiO2-P25及FeC2O4为前驱物制备了Fe3 掺杂TiO2光催化剂--Fe/TiO2.X射线衍射结果表明,500 ℃煅烧温度下的Fe/TiO2主要是锐态矿晶型,当掺Fe3 量为0.5%(质量分数,下同)时,Fe3 以取代掺杂形式进入TiO2晶格,而当掺Fe3 量达5.0%时,则出现α-Fe2O3的特征衍射峰;900 ℃煅烧温度下的Fe/TiO2则均为金红石晶型,掺Fe3 量达2.0%～5.0%时,出现Fe2TiO5的特征衍射峰.4-氯苯酚的光催化实验结果表明,煅烧温度及Fe3 掺杂量对Fe/TiO2的光催化活性有显著影响,以煅烧温度500 ℃及掺Fe3 量0.5%的Fe/TiO2为光催化剂,反应80 min,4-氯苯酚的降解率达100%,总有机碳去除率约95%.     

活性炭纤维负载TiO2光催化降解甲醛的影响因素

利用自制光催化气体反应器体系,以活性炭纤维负载TiO2作催化剂,在紫外光照射下模拟降解室内污染气体甲醛,测试了活性炭纤维负载TiO2催化剂的催化活性,探讨了紫外光光强、催化剂的酸度、反应器内湿度及反应时间等控制反应的主要因素对甲醛降解率的影响。结果表明,活性炭纤维与TiO2的协同作用大大提高了对甲醛的降解效果;紫外光强增倍对甲醛降解率有一定提高,但提高幅度仅为11.71%;活性炭纤维用pH=5的TiO2溶胶浸泡做催化剂对甲醛的降解效果最好,60 min内降解率达到68.37%;反应器内的湿度为81%甲醛降解率最高,反应60 min后达82.2%;随着反应时间的延长,甲醛降解率的上升幅度不断减小,最高只能达到94.59%。     

活性炭纤维负载TiO_2光催化降解甲醛的影响因素

利用自制光催化气体反应器体系,以活性炭纤维负载TiO2作催化剂,在紫外光照射下模拟降解室内污染气体甲醛,测试了活性炭纤维负载TiO2催化剂的催化活性,探讨了紫外光光强、催化剂的酸度、反应器内湿度及反应时间等控制反应的主要因素对甲醛降解率的影响.结果表明,活性炭纤维与TiO2的协同作用大大提高了对甲醛的降解效果;紫外光强增倍对甲醛降解率有一定提高,但提高幅度仅为11.71%;活性炭纤维用pH=5的TiO2溶胶浸泡做催化剂对甲醛的降解效果最好,60 min内降解率达到68.37%;反应器内的湿度为81%甲醛降解率最高,反应60 min后达82.2%;随着反应时间的延长,甲醛降解率的上升幅度不断减小,最高只能达到94.59%.     

Photocatalytic degradation of mixed gaseous carbonyl compounds at low level on adsorptive TiO2/SiO2 photocatalyst using a fluidized bed reactor

An adsorptive silica-supported titania photocatalyst TiO(2)/SiO(2) was prepared by using nanosized titania (anatase) immobilized on silica gel by the sol-gel technique with the titanium tetra isopropoxide as the main raw material and acetic acid as the acid catalyst. Meanwhile the structure and properties of the TiO(2)/SiO(2) photocatalyst were studied by means of many modern analysis techniques such as TEM, XRD, and BET. Gas-solid heterogeneous photocatalytic decomposition of four carbonyl compounds mixture at low concentration levels over ultraviolet irradiated TiO(2)/SiO(2) photocatalyst were carried out with high degradation efficiencies in a coaxial triple-cylinder-type fluidized bed photocatalytic reactor, which provided efficient continuous contact of ultraviolet photons, silica-supported titania photocatalyst, and gaseous reactants. Experimental results showed that the photocatalyst had a high adsorption performance and a good photocatalytic activity for four carbonyl compounds mixture. Some factors influencing the photocatalytic decomposition of the mixed carbonyl compounds, i.e. the gas flowrate, relative humidity, concentration of oxygen, and illumination time, were discussed in detail. It is found that the photocatalytic reaction rate of four carbonyl compounds decreased in this order: propionaldehyde, acetone, acetaldehyde and formaldehyde.     

TiO_2光催化涂料的制备及其降解甲醛研究

自制TiO_2光催化涂料,重点对所制备的涂料在室内进行降解甲醛研究,考察了在不同分散剂、不同光催化剂以及不同甲醛初始浓度、不同光源、不同温度和不同湿度等环境因素下涂料对甲醛降解率的影响。结果表明,选用聚丙烯酸钠离子型分散剂,铜金属掺杂TiO_2光催化剂制备的光催化涂料对甲醛降解率达80%以上且具有良好的耐久性,在室温(20℃左右)湿度50%日光灯照射下,甲醛初始浓度5μL时效果最佳。     

N-doped SiO2/TiO2 mesoporous nanoparticles with enhanced photocatalytic activity under visible-light irradiation

Mesoporous nanocrystalline N-doped SiO2/TiO2 visible-light photocatalysts were prepared by treating SiO2/TiO2 xerogels in a flow of nitrogen gas bubbled through concentrated ammonia solution. Structural characterization and performance analysis results revealed that the addition of SiO2 remarkably altered the phase composition, specific surface area, microstructure, as well as the photocatalytic activity of N-doped TiO2. The presence of SiO2 in N-doped TiO2 particles suppressed the formation of rutile phase and the crystal growth of N-doped TiO2 particles during thermal calcinations. When weight ratio of SiO2/TiO2 was in 0.05-0.20, the N-doped SiO2/TiO2 exhibited higher photocatalytic activity than the N-doped TiO2, and optimum ratio was found to be 0.05. The enhanced photocatalytic activity could be attributed to the higher specific area, larger pore volume, and more surface hydroxyl groups in the catalyst.     

Fe2O3-Cr2O3/TiO2系列催化剂的结构和脱硝性能

研究以纳米TiO2为载体,浸渍负载过渡金属氧化物,以CO为还原剂的脱硝催化剂的脱硝性能。实验中以计算量的Ni（NO3）2和Fe（NO3）3混合溶液浸渍纳米TiO2粉末,室温下搅拌30 min至混合均匀,放入旋转蒸发器中,70℃下至水分蒸干为止;所得粉末在550℃下、空气气氛中焙烧4 h即得所需催化剂。用以上方法分别制备2%Fe2O3-10%Cr2O3/TiO2、4%Fe2O3-8%Cr2O3/TiO2、6%Fe2O3-6%Cr2O3/TiO2、8%Fe2O3-4%Cr2O3/TiO2与10%Fe2O3-2%Cr2O3/TiO2等5种催化剂样品。实验结果表明,制备的催化剂具有较好的结构,分散较为均匀。对于CO＋NO反应,Fe2O3-Cr2O3/TiO2系列催化剂具有较好的催化活性,NO的转化率都达到了100%。其中,10%Fe2O3-2%Cr2O3/TiO2样品具有最好的低温活性,H2-TPR结果表明,这是由于10%Fe2O3-2%Cr2O3/TiO2催化剂更易于被CO预还原。     

微乳液法合成掺硫纳米TiO_2及其光催化性能研究

以钛酸四丁酯为钛源,硫脲为掺硫前驱物,采用聚乙二醇辛基苯基醚（Triton X-100）/正己醇/环己烷/氨水的微乳液体系合成了掺硫的纳米TiO2粉体;对其结构进行了表征,以甲基橙为目标降解物考察了其光催化性能。烧结温度通过影响TiO2的晶型转变和颗粒尺寸来影响其光催化性能,随着烧结温度的升高,TiO2的光催化性能先是提高,然后迅速降低;在600℃烧结2 h时催化剂的降解性能达到最佳。掺杂硫可提高TiO2的光催化活性,随着掺杂量的增加,催化剂对甲基橙的降解率先快速增加然后缓慢降低,当掺杂量为S/Ti（摩尔比）=0.01∶1时TiO2的光催化降解效果最好。催化剂在用量较小时迅速提高TiO2的光催化降解性能,而后随着用量的增大反而降低,当催化剂用量为1.5 g/L时,对甲基橙的降解效果最好。     

Catalytic destruction of 1,2-dichlorobenzene on V2O5-WO3/Al2O3-TiO2 catalyst

Studies on the catalytic destruction of 1,2-dichlorobenzene were carried out on a specially constructed semi-technical equipment whose most important element was a catalytic reactor with a monolithic catalyst in the form of 150 x 150 x 100 mm cubes. A catalyst made from cordierite with an active layer composed of Al2O3 - 64 wt%, TiO2 - 26 wt%, V2O5 - 6.6 wt% and WO3 - 3.4 wt% was used. The reactor made it possible to carry out the process in the temperature range 150-350 degrees C, at variable catalyst loading and different velocities of gas flow through the reactor. The content of 1,2-dichlorobenzene in the air was analysed by a chromatographic method. A significant effect of catalyst loading and temperature on 1,2-dichlorobenzene destruction efficiency was observed and no effect of the linear flow velocity through the catalyst on o-dichlorobenzene destruction efficiency was reported. The applied vanadium-tungsten catalyst on a monolithic carrier made from TiO2/gamma-Al2O3 revealed very good activity that resulted in an over 80% efficiency of 1,2-dichlorobenzene destruction at the temperature around 250 degrees C at a very high catalyst loading reaching ca. 8200 h(-1). Additionally, in this study the kinetics of 1,2-dichlorobenzene decomposition was determined, specifying the order of reaction and dependence of the decomposition rate constant on temperature, using a simple power-rate law model.