Development of an In-Line System for the Analysis of 4,4′-DDT in Water

An in-line system for trace persistent organic pollutants (POPs) in water was developed by using a laboratory-made hollow fiber membrane (HFM) unit connected with a high-resolution gas chromatograph-mass spectrometer (HRGC-MS). The semivolatile organic compound, 4,4′-Dichlorodiphenyl trichloroethane (4,4′-DDT), was chosen as a representative of a persistent organic compound. The synthetic water contaminated with 4,4′-DDT was passed through the HFM unit, the extraction occurred by the analyte pervaporated and permeated, then stripped into HRGC-MS. Several factors were investigated for the high extraction efficiency. The best performance was obtained at sample and stripping gas flow rates of 6 and 9 mLmin^?1, respectively, and desorption temperature of 60°C. At this temperature, the diffusion rate was enhanced by 15 times over 25°C. A wide linear dynamic range was obtained, i.e., 0.10–1.0 mgL^?1, with a limit of detection (LOD) of 90 μgL^?1. The extraction efficiency of 4,4′-DDT in real water samples was in the range of 83–94%. Real water samples were analyzed and 0.6 μgL^?1 of 4,4′-DDT was found in unregistered bottled water and 7.0 μgL^?1 in tap water.     

Analysis of organophosphorus pesticides in whole milk by solid phase microextraction gas chromatography method

Solid phase microextraction (SPME) was used for the extraction of residual coumaphos and dichlorvos in whole milk. The residues were analyzed by capillary gas chromatography equipped with nitrogen phosphorus detector (GC-NPD). A manual SPME holder with a 100-microm polyacrylate fiber was used. The optimized conditions for extraction by SPME method were: sample agitation, absorption temperature of 30 degrees C, absorption time of 40 min, desorption time of 10 min, and sample volume was 16.0 mL in the vial. Under these conditions, the calibration graphs were linear in the range of 0.17 microgL-1 to 1.75 microgL-1 for coumaphos and 0.69 microgL-1 to 6.90 microgL-1 for dichlorvos. Precision was good with RSD values of 13% for coumaphos and 14% for dichlorvos. The detection limits (LOD) were 0.060 microgL-1 for dichlorvos and 0.052 for coumaphos. The quantification limits (LOQ) were 0.086 microgL-1 for dichlorvos and 0.066 microgL-1 for coumaphos. The results obtained in this study suggest that SPME is a suitable technique for residual pesticide analysis of milk. The data demonstrate that particular OP pesticides used in dairy farming in the region of Minas Gerais were found to contaminate cow whole milk, and the residues are not removed by treating the milk by boiling.     

Persistent organic pollutants, brominated flame retardants and synthetic musks in fish from remote alpine lakes in Switzerland

Remote alpine lakes do not receive any direct aquatic inputs from anthropogenic activities. Therefore, these ecosystems may receive persistent organic compounds (POPs) by direct atmospheric deposition, only. Consequently, fish dwelling in these ecosystems represent an excellent indicator for the long-term atmospheric input of bioaccumulating and persistent contaminants. In the present study, fish from seven remote alpine lakes, located between 2062 and 2637 m above sea level in south eastern Switzerland (Grisons), were investigated. Lipid-based fish tissue concentrations of pesticides including dichlorodiphenyltrichloroethane (DDT) and its transformation products (2,4'-DDT, 4,4'-DDT, 2,4'-dichlorodiphenyldichloroethane (DDD), 4,4'-DDD, 2,4'-dichlorodiphenyldichloroethene (DDE), 4,4'-DDE), as well as dieldrin, heptachlor exo-epoxide (HPEX), hexachlorobenzene (HCB), hexachlorocyclohexanes (HCH), polychlorinated biphenyls (PCB), polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/F), and polybrominated diphenyl ethers (PBDE) were measured. In addition, seven synthetic musk compounds (Crysolide (ADBI), Phantolide (AHMI), Fixolide (AHTN), Traseolide (ATII), Galaxolide (HHCB), musk ketone (MK), and musk xylene (MX)) were determined. Concentrations of PCB, PCDD/F, and PBDE were in the same range as in fish from the major lakes situated in the Swiss plateau, indicating mainly atmospheric input of these persistent compounds. In contrast, concentrations of synthetic musks which are used as fragrances in laundry detergents and cosmetic products were distinctly lower than concentrations in fish from Swiss plateau lakes which receive inputs from waste water treatment plants.     

Comparison of semipermeable membrane device (SPMD) and large-volume solid-phase extraction techniques to measure water concentrations of 4,4'-DDT, 4,4'-DDE, and 4,4'-DDD in Lake Chelan, Washington

Semipermeable membrane devices (SPMDs) spiked with the performance reference compound PCB29 were deployed 6.1 m above the sediments of Lake Chelan, Washington, for a period of 27 d, to estimate the dissolved concentrations of 4,4'-DDT, 4,4'-DDE, and 4,4'-DDD. Water concentrations were estimated using methods proposed in 2002 and newer equations published in 2006 to determine how the application of the newer equations affects historical SPMD data that used the older method. The estimated concentrations of DDD, DDE, and DDD calculated using the older method were 1.5-2.9 times higher than the newer method. SPMD estimates from both methods were also compared to dissolved and particulate DDT concentrations measured directly by processing large volumes of water through a large-volume solid-phase extraction device (Infiltrex 300). SPMD estimates of DDD+DDE+DDT (SigmaDDT) using the older and newer methods were lower than Infiltrex concentrations by factors of 1.1 and 2.3, respectively. All measurements of DDT were below the Washington State water quality standards for the protection of human health (0.59 ng l(-1)) and aquatic life (1.0 ng l(-1)).     

Temporal trend of bis(4-chlorophenyl) sulfone, methylsulfonyl-DDE and -PCBs in Baltic guillemot (Uria aalge) egg 1971-2001--a comparison to 4,4'-DDE and PCB trends

The dynamics of organohalogen contaminants and their metabolites are best studied over time by analysis of biota at high trophic levels. In this study, time trends, 1971-2001, of bis(4-chlorophenyl) sulfone (BCPS) and of methylsulfonyl-substituted metabolites of PCBs and 4,4'-DDE, were investigated in eggs of guillemot (Uria aalge) hatching in the Baltic Proper. Temporal trends of PCBs, trans-nonachlor, beta-HCH, 4,4'-DDT, and 4,4'-DDE were also assessed. Tris(4-chlorophenyl) methane (TCPMe), a 4,4'-DDT by-product, was detected in the eggs. The concentration of BCPS ranged between 2.6-0.76 microg/g on a lipid weight basis over the three decades and showed a significant 1.6% annual decrease. Three metabolites of PCBs, i.e. 3'-MeSO2-CB101, 4'-MeSO2-CB101 and 4-MeSO2-CB149, were quantified in all samples over time and showed an annual decrease of approximately 3% compared to MeSO2-DDE with a decrease of 8.9%. The methylsulfonyl-PCB and -DDE metabolites are eliminated more slowly than the persistent PCB congeners and 4,4'-DDE. Trans-nonachlor decreases by 16% compared to 19% and 9% for 4,4'-DDT and beta-HCH, respectively. The concentration of TCPMe in guillemot decreased by 8.2% per year. A linear relationship was found between TCPMe and 4,4'-DDE concentrations which supports the theory that TCPMe has an origin as a contaminant in commercial 4,4'-DDT products. The very slow decrease in BCPS concentrations is notable and remains to be explained. BCPS is still present at rather high concentrations in the guillemot eggs. The enantiomeric fraction varied between 0.27 and 0.67 which indicates less of a specific retention of the chiral MeSO2-PCBs in guillemot eggs than in grey seal tissues, for example. Independent of meta- or para-substitution of the sulfone group, the most accumulative atropisomer of each of four MeSO2-PCB pairs has been assigned an absolute R structure.     

Measurement of pollution levels of organochlorine and organophosphorus pesticides in water, soil, sediment, and shrimp to identify possible impacts on shrimp production at Jiquilisco Bay

This study aims to identify levels of several organochlorine and organophosphorus compounds in shrimp-raising areas of coastal El Salvador, to assess potential impacts on shrimp growth and survival that hamper the sustainability of aquaculture in the region. The paper reports the current levels of γ-HCH, 4,4'-DDT, 4,4'-DDE, 4,4'-DDD, endrin, dieldrin, heptachlor, parathion, methyl parathion, and etoprophos in soils (depth 20 cm), sediments (depth 5 cm), shrimp (Penaeus sp.), and water of three rearing ponds and also in the sediment (depth 5 cm) and water surrounding those ponds in Jiquilisco Bay. Sampling was carried out during the dry (January-March) and rainy (June-August) seasons of 2008. The presence of pesticides in the samples of water, shrimp, and sediment at shrimp ponds was not detected in either season; however, in soil samples (depth 20 cm) taken from these ponds, heptachlor, endrin, dieldrin, 4,4'-DDD, and 4,4'-DDT were identified at concentrations below the method limit of quantification (LOQ), and 4,4'-DDE was found in a concentration falling in the range from 3.85 to 19.61 ng/g. In samples of water taken at the bay water intakes to the rearing ponds, we observed dieldrin concentrations in the range between 0.085 ng/mL and 0.182 ng/mL during the dry season. In the samples of sediments taken in the surrounding areas of shrimp ponds, we found-for both seasons-that in 60 % of the samples, 4,4'-DDE was present in concentrations ranging from 3.75 ng/g to 30.97 ng/g. Additionally, in the rainy season, we observed heptachlor in sediment at concentrations below the method quantification limit. It was concluded that organochlorine compounds from pesticides are still present in Jiquilisco Bay, trapped in deep sediment, even though they have been banned since the 1980s. These were not detected in shrimp tissue, surface water, and shallow sediment in rearing ponds, and hence, we do not believe their presence has any major impact on shrimp production in sampled areas.     

Persistent organochlorine pollutants in children working at a waste-disposal site and in young females with high fish consumption in Managua, Nicaragua

The aim of this study was to assess persistent organochlorine pollutant (POP) levels in serum collected from children (11-15 years old) working and sometimes also living at the municipal waste-disposal site in Managua, located at the shore of Lake Managua, and in nonworking children living both nearby and also far away from the waste-disposal site. The influence of fish consumption was further evaluated by assessing POPs levels in serum from young women (15-24 years old) with markedly different patterns of fish consumption from Lake Managua. 2,2-bis(4-chlorophenyl)-1,1,1-trichloro-ethane (4,4'-DDT) and 2,2-bis(4-chlorophenyl)-1,1-dichloro-ethene (4,4'-DDE), gamma-hexachlorocyclohexane (gamma-HCH), polychlorinated biphenyls, pentachlorophenol, and polychlorobiphenylols were quantified in all samples. In general, the levels observed were higher than those reported in children from developed countries, such as Germany and United States. Toxaphene, aldrin, dieldrin, and beta-HCH could not be identified in any sample. The children working at the waste-disposal site had higher levels of POPs compared with the nonworking reference groups. In children not working, there were also gradients for several POPs, according to vicinity to the waste-disposal site. Moreover, in children, as well as in young women, there were gradients according to fish consumption. The most abundant component was 4,4'-DDE, but at levels still lower than those reported in children from malarious areas with a history of recent or current application of 4,4'-DDT for vector control.     

Assessment of commercially available polymeric materials for sorptive microextraction of priority and emerging nonpolar organic pollutants in environmental water samples

Among the different organic pollutants, persistent organic pollutants and emerging organic contaminants (EOCs) are of particular concern due to their potentially dangerous effects on the ecosystems and on human health. In the framework of the analysis of some of these organic pollutants in water samples, sorptive extraction devices have proven to be adequate for their monitoring. The efficiency of four commercially available and low-cost polymeric materials [polypropylene, poly(ethylene terephthalate), Raffia, and polyethersulfone (PES)] for the simultaneous extraction of 16 organic compounds from five different families from environmental water samples was evaluated in this work. Firstly, the homogeneity of the sorbent materials was confirmed by means of Raman spectroscopy. After the optimization of the parameters affecting the extraction and the liquid desorption steps, it was found that PES showed the largest efficiencies for slightly polar analytes and, to a lesser extent, for nonpolar analytes. Additionally, Raffia rendered good extraction efficiencies for nonpolar compounds. Thus sorptive extraction methods followed by large volume injection-programmable temperature vaporizer-gas chromatography-mass spectrometry were validated using PES and Raffia as sorbent materials. The validation of the method provided good linearity (0.978?r ²?r ²?-1 level). Finally, these materials were applied to the analysis of contaminants in environmental water samples.     

BTEX determination in water matrices using HF-LPME with gas chromatography-flame ionization detector

In the present work, a sample pre-treatment technique for the determination of trace concentrations of benzene, toluene, ethyl benzene and xylene (BTEX) in aqueous samples has been developed and applied to analysis of the selected analytes in environmental water samples. The extraction procedure is based on coupling polypropylene hollow-fiber liquid phase microextraction (HF-LPME) with gas chromatography by flame ionization detection (GC-FID). The effective parameters such as organic solvent, extraction time, agitation speed and salting effect were investigated. Good reproducibilities of the extraction performance were obtained, with the RSD values ranging from 2.02 to 4.61% (n=5). The method provided 41.47-128.01 fold preconcentration of the target analytes. The limits of detections for the BTEX were in the range of 0.005-03microg ml(-1). In addition, sample clean-up was achieved during LPME due to the selectivity of the hollow fiber, which prevented undesirable large molecules from being extracted. Real samples (River and waste waters) containing BTEX were examined using this method with good linearity and precision (RSDs most lower than 6.00%, n=5). All experiments were carried out at room temperature, 22+/-0.5 degrees C.     

Optimisation of pressurised liquid extraction for elimination of sulphur interferences during determination of organotin compounds in sulphur-rich sediments by gas chromatography with flame photometric detection

A simple method for species-selective analysis of organotin compounds (OTCs) (butyl and phenyl) in sediments was developed. The sample preparation procedure was specifically optimised for sulphur-rich sediments to eliminate interferences from elemental sulphur and organosulphur compounds. Tin species were extracted from sediment samples using pressurised liquid extraction technique (PLE), ethylated - with simultaneous extraction to isooctane - in aqueous phase with sodium tetraethylborate (NaBEt(4)) and separated/detected by gas chromatography with flame photometric detection (GC-FPD). PLE operational variables (extraction temperature and pressure, solvent composition and number of static extraction steps) and extract handling routine were fine-tuned to minimise the amount of extracted interferents while keeping OTCs recovery at an acceptable level. Best results were obtained after extraction of sediment samples with methanol/water (75% v/v methanol) solution of acetic acid/sodium acetate with tropolone addition (0.6 g l(-1)). Derivatisation of low temperature, high-pressure (50 degrees C, 13.8 MPa) extracts gives isooctane extracts which are clean enough to be directly analysed by GC-FPD without any further cleanup. Interferences from elemental sulphur were completely eliminated while concentrations of other interferents were reduced to the level not impairing quantitation of OTCs under the study. No negative effects in terms of chromatographic column deterioration were observed after repeated injections of such extracts. Two certified reference materials, BCR646 and PACS-2, were analysed to assess performance of the method. Recoveries of all OTCs under the study, except MBT, were in the range of 91-114%. MBT extraction efficiency was low (34-47%) therefore the method is unsuitable for precise determinations of this compound.     

Evaluation of GC-ion trap-MS/MS methodology for monitoring PCDD/Fs in infant formulas

The application of high resolution gas chromatography in combination with low resolution mass spectrometry with electron ionization and MS/MS detection (HRGC-MS/MS) is tested for its use in the analysis of PCDD/Fs in infant formulas. Development of the analytical method was based upon EPA directrices and international recommendations. Calibration linearity was tested and average relative response for any native and labelled compound over the five-point calibration range below 14% was found. The precision and accuracy of the proposed analytical procedure are also presented. Results obtained are in agreement with EPA criteria. The method is applied to the analysis of a number of initial and follow-on milk based infant formulas. In general, HRGC-MS/MS constitutes an interesting method for the analysis of dioxins in such matrices.     

Identification and quantification of polychlorinated biphenyls and some endocrine disrupting pesticides in human adipose tissue from Finland

Organochlorine pesticides and polychlorinated biphenyls (PCBs) were analysed in extracts of human adipose tissue. The samples consisted of abdominal, mammary, and perirenal fat tissue of 27 Finnish adult males and females. Lipids were separated from the low-molecular compounds by preparative gel permeation chromatography (GPC) and the extracts were further cleaned-up using Florisil chromatography. The compounds were analysed in the extracts by gas chromatography (GC) using electron capture detection and by GC-mass spectrometry in the selected ion monitoring mode. Of the 23 analysed pesticide residues only seven could be detected in the extracts. All the extracts contained the DDT metabolite 4,4'-DDE, hexachlorobenzene, and PCBs. Other compounds found in the extracts were 4,4'-DDT, 4,4'-DDD, pentachlorobenzene, and beta- and gamma-hexachlorocyclohexane (HCH). The antiandrogenic 4,4'-DDE was the most abundant pesticide with concentration levels ranging from 3.5 to 3229 ng/g lipids (ppb). The mean concentration of DDE was 567 ppb, of pesticides in all 1008 ppb and of PCBs 504 ppb. Several of the identified compounds have been shown to exhibit endocrine disrupting effects. Statistical analysis showed a positive age correlation of DDE in females and hexachlorobenzene in males. No statistically significant differences were found for concentrations of individual compounds between sexes.     

Evaluation of pressurized liquid extraction for determination of organophosphorus and pyrethroid pesticides in soybean

The purpose of this study was to develop an analytical method for the determination of organophosphorus and pyrethroid pesticides in soybean by pressurized liquid extraction (PLE). Two organic solvents, acetone and acetonitrile, were evaluated as extraction solvents. In both cases, the amount of extract was enhanced with increasing extraction temperature. The extracts obtained using acetonitrile were measured by gas chromatography/mass spectrometry after a cleanup process based on the analytical method for the Japanese Positive List System for Agricultural Chemicals Remaining in Foods. The effect of extraction temperature (range: 40- 130°C) on extraction efficiency was evaluated by a recovery study using 21 organophosphorus pesticides and 10 pyrethroid pesticides as target analytes and acetonitrile as the solvent. The results indicated that at 130°C, some organophosphorus pesticides might be degraded, whereas extraction temperatures between 70°C and 100°C were optimal. Next, a prepared sample containing fenitrothion and permethrin was analyzed. Although the sample was not soaked in water prior to analysis, PLE provided analytical results comparable to those obtained by solvent extraction with homogenization. Therefore, PLE is considered a simple and alternative technique for the extraction of organophosphorus and pyrethroid pesticides in soybean.     

Evaluation of pressurized liquid extraction for determination of organophosphorus and pyrethroid pesticides in soybean

The purpose of this study was to develop an analytical method for the determination of organophosphorus and pyrethroid pesticides in soybean by pressurized liquid extraction (PLE). Two organic solvents, acetone and acetonitrile, were evaluated as extraction solvents. In both cases, the amount of extract was enhanced with increasing extraction temperature. The extracts obtained using acetonitrile were measured by gas chromatography/mass spectrometry after a cleanup process based on the analytical method for the Japanese Positive List System for Agricultural Chemicals Remaining in Foods. The effect of extraction temperature (range: 40– 130°C) on extraction efficiency was evaluated by a recovery study using 21 organophosphorus pesticides and 10 pyrethroid pesticides as target analytes and acetonitrile as the solvent. The results indicated that at 130°C, some organophosphorus pesticides might be degraded, whereas extraction temperatures between 70°C and 100°C were optimal. Next, a prepared sample containing fenitrothion and permethrin was analyzed. Although the sample was not soaked in water prior to analysis, PLE provided analytical results comparable to those obtained by solvent extraction with homogenization. Therefore, PLE is considered a simple and alternative technique for the extraction of organophosphorus and pyrethroid pesticides in soybean.     

Analysis of volatile and semivolatile organic compounds in municipal wastewater using headspace solid-phase microextraction and gas chromatography.

The aim of this work was to develop a simple and fast analytical method for the determination of a wide range of organic compounds (volatile and semivolatile compounds) in municipal wastewater. The headspace-solid-phase microextraction (HS-SPME) and gas chromatography (with mass spectroscopy) was used for determination of the organic compounds. In this study, 39 organic compounds were determined, including 3 sulfur compounds, 28 substituted benzenes, and 8 substituted phenols. The extraction parameters, such as types of SPME fiber, extraction temperature, extraction time, desorption time, salt effect, and magnetic stirring, were investigated. The method had very good repeatability, because the relative standard deviations ranged from 0.5 to 12%. The detection limit of each compound was at or below the microgram-per-liter level. This method was applied for determination of the organic compounds in raw wastewater, primary effluent, secondary effluent, and chlorinated secondary effluent samples from the Chania Municipal Wastewater Treatment Plant (Crete, Greece).     

Performance characteristics of a regenerative catalytic oxidizer for treating VOC-contaminated airstreams

A pilot apparatus of a regenerative catalytic oxidizer (RCO) equipped with two electrical heaters and two 20-cm i.d. x 200-cm height regenerative beds was used to treat methyl ethyl ketone (MEK) and toluene, respectively, in an airstream. The regenerative beds were packed with gravel (approximate particle size 1.25 cm, specific area 205 m2/m3, and specific heat capacity 840 J/kg degree C) as a solid regenerative material and K-type thermal couples for measuring solid and gas temperatures, respectively. The catalyst bed temperature was kept around 400 degrees C and the gas superficial velocity was operated at 0.234 m/sec. This investigation measured and analyzed distributions of solid and gas temperatures with operating time and variations of volatile organic compound (VOC) concentrations in the regenerative beds. The overall VOC removal efficiency exceeded 98% for MEK and 95% for toluene. Degradation of VOCs will exist for MEK on the surface of solid material (gravel) in the temperature range of 330-400 degrees C, but toluene does not exhibit this phenomenon.     

Kinetics of catalytic oxidation of benzene, n-hexane, and emission gas from a refinery oil/water separator over a chromium oxide catalyst

With the advances made in the past decade, catalytic incineration of volatile organic compounds (VOCs) has become the technology of choice in a wide range of pollution abatement strategies. In this study, a test was undertaken for the catalytic incineration, over a chromium oxide (Cr2O3) catalyst, of n-hexane, benzene, and an emission air/vapor mixture collected from an oil/water separator of a refinery. Reactions were carried out by controlling the feed stream to constant VOC concentrations and temperatures, in the ranges of 1300-14,700 mg/m3 and 240-400 degrees C, respectively. The destruction efficiency for each of the three VOCs as a function of influent gas temperature and empty bed gas residence time was obtained. Results indicate that n-hexane and the oil vapor with a composition of straight- and branch-chain aliphatic hydrocarbons exhibited similar catalytic incineration effects, while benzene required a higher incineration temperature or longer gas retention time to achieve comparable results. In the range of the VOC concentrations studied, at a given gas residence time, increasing the operating temperature of the catalyst bed increased the destruction efficiency. However, the much higher temperatures required for a destruction efficiency of over 99% may be not cost-effective and are not suggested. A first-order kinetics with respect to VOC concentration and an Arrhenius temperature dependence of the kinetic constant appeared to be an adequate representation for the catalytic oxidation of these volatile organics. Activation energy and kinetic constants were estimated for each of the VOCs. Low-temperature destruction of the target volatile organics could be achieved by using the Cr2O3 catalyst.     

Gas chromatographic analysis of organic marker compounds in fine particulate matter using solid-phase microextraction

A gas chromatographic method that uses solid-phase microextraction for analysis of organic marker compounds in fine particulate matter (PM2.5) is reported. The target marker compounds were selected for specificity toward emission from wood smoke, diesel or gasoline combustion, or meat cooking. Temperature-programmed volatilization analysis was used to characterize the thermal stabilities and volatile properties of the compounds of interest. The compounds were thermally evaporated from a quartz filter, sorbed to a solid phase microextraction (SPME) fiber, and thermally desorbed at 280 degrees C in a gas chromatograph injection port connected via a DB 1701 capillary separating column. Various experimental parameters (fiber type, time, and temperature of sorption) were optimized. It was found that high extraction yield could be achieved using a polyacrylate fiber for polar substances, such as levoglucosan, and a 7-microm polydimethylsiloxane (PDMS)-coated fiber for nonpolar compounds, such as hopanes and polyaromatic hydrocarbon. A compromise was made by selecting a carboxen/PDMS fiber, which can simultaneously extract all of the analytes of interest with moderate-to-high efficiency at 180 degrees C within a 30-min accumulation period. The optimized method was applied to the determination of levoglucosan in pine wood combustion emissions. The simplicity, rapidity, and selectivity of sample collection with a polymer-coated SPME coupled to capillary gas chromatography (GC) made this method potentially useful for atmospheric chemistry studies.     

Contamination by selected chlorinated pesticides in surface waters in Hanoi, Vietnam

Fifteen insecticides, which were banned in Vietnam in the period from 1990 to 1998, were chosen for the investigation of surface water samples in Hanoi and its surroundings. The investigation was focused on an area of approximately 30 by 20 km. Thirty water samples, in total were analysed: 11 samples from the Red river, seven from the Duong river, four from various lakes (West lake, Thuyen Quang, Bay Mau, Ba Mau), six from irrigation canals and two samples from wells. The procedure was repeated in November 1998 and in August 1999. The results showed that the contamination of the banned pesticides was highest in the rivers and then in the irrigation canals, followed by the lakes and wells. These pesticides could hardly be determined in just two drinking water samples (wells) and their concentrations rarely exceeded detection limits (0.05-0.25 ng l(-1)). The mean concentrations of sigmaHCHs (alpha, beta, gamma, delta-HCH) and sigmaDDTs (2,4'-, 4,4'-DDE; 2,4'-, 4,4'-DDD; 2,4'-, 4,4'-DDT) in the rivers were 17.2 +/- 71.8 and 43.7 +/- 79.9 ng l(-1) in the dry season (DS, November 1998), 29.3 +/- 117 and 56.1 +/- 65.6 ng l(-1) in the rainy season (RS, August 1999), respectively. However, the highest concentration of DDTs detected in a river sample (DS): 0.324 microg l(-1) was much lower than their allowable limit of concentration in surface waters, which is accorded with Criteria of Vietnam (1995) (DDTs < 10 microg l(-1)). Moreover, endrin, heptachlor, aldrin were also detected in most of water samples with considerable mean concentrations in rivers: 25.3 +/- 40.5, 17.4 +/- 23.8, 11.0 +/- 9.02 ng l(-1) in the DS and 18.5 +/- 23.2, 19.3 +/- 29.0, 12.8 +/- 8.44 ng l(-1) in the RS, respectively. Heptachlor epoxide (isomer A) and dieldrin were detected in some water samples with lowest concentrations.     

Removal of polycyclic aromatic hydrocarbons from aged-contaminated soil using cyclodextrins: experimental study

The removal of polycyclic aromatic hydrocarbons (PAHs) from soil using water as flushing agent is relatively ineffective due to their low aqueous solubility. However, addition of cyclodextrin (CD) in washing solutions has been shown to increase the removal efficiency several times. Herein are investigated the effectiveness of cyclodextrin to remove PAH occurring in industrially aged-contaminated soil. Beta-cyclodextrin (BCD), hydroxypropyl-beta-cyclodextrin (HPCD) and methyl-beta-cyclodextrin (MCD) solutions were used for soil flushing in column test to evaluate some influent parameters that can significantly increase the removal efficiency. The process parameters chosen were CD concentration, ratio of washing solution volume to soil weight, and temperature of washing solution. These parameters were found to have a significant and almost linear effect on PAH removal from the contaminated soil, except the temperature where no significant enhancement in PAH extraction was observed for temperature range from 5 to 35 degrees C. The PAHs extraction enhancement factor compared to water was about 200.