首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到19条相似文献,搜索用时 156 毫秒
1.
This work was conducted to determine the practicability of using a new adsorbent 4-ethyl thiosemicarbazide intercalated,organophilic calcined hydrotalcite(ETSC-OHTC) for the removal of uranium(U(VI)),and thorium(Th(IV)) from water and wastewater.The FTIR analysis helped in realizing the involvement of nitrogen and sulphur atoms of ETSC in binding the metal ions through complex formation.Parameters like adsorbent dosage,solution pH,initial metal ions concentration,contact time and ionic strength,that influence adsorption phenomenon,were studied.The optimum pH for maximum adsorption of U(VI) and Th(IV) was found to be in the range 4.0-6.0.The contact time required for reaching equilibrium was 4 hr.The pseudo second-order kinetic model was the best fit to represent the kinetic data.Analysis of the equilibrium adsorption data using Langmuir,Freundlich and Sips models showed that the Freundlich model was well suited to describe the metal ions adsorption.The K F values were 25.43 and 29.11mg/g for U(VI) and Th(IV),respectively,at 30°C.The adsorbent can be regenerated effectively from U(VI) and Th(IV) loaded ones using 0.01mol/L HCl.The new adsorbent was quite stable for many cycles,without much reduction in its adsorption capacity towards the metals.  相似文献   

2.
The removal of heavy-metal ions from aqueous solutions by using dried activated sludge has been investigated in batch systems. Effect of solution pH, initial metal ion concentration, and temperature were determined. The results of the kinetic studies showed that the uptake processes of the two metal ions(Cd(Ⅱ) and Pb(Ⅱ)) followed the pseudo-second-order rate expression. The equilibrium data fitted very well to both the Langmuir and Freundlich adsorption models. The FT-IR analysis showed that the main mechanism of Cd(Ⅱ) and Pb(Ⅱ) biosorption onto dried activated sludge was their binding with amide I group.  相似文献   

3.
Bamboo charcoal (BC) was used as starting material to prepare Co-Fe binary oxideloaded adsorbent (Co-Fe-MBC) through its impregnation in Co(NO3)2 , FeCl3 and HNO3 solutions simultaneously, followed by microwave heating. The low-cost composite was characterized and used as an adsorbent for Cr(VI) removal from water. The results showed that a cobalt and iron binary oxide (CoFe2O4 ) was uniformly formed on the BC through redox reactions. The composite exhibited higher surface area (331 m2/g) than that of BC or BC loaded with Fe alone (Fe-MBC). The adsorption of Cr(VI) strongly depended on solution pH, temperature and ionic strength. The adsorption isotherms followed the Langmuir isotherm model well, and the maximum adsorption capacities for Cr(VI) at 288 K and pH 5.0 were 35.7 and 51.7 mg/g for Fe-MBC and Co-Fe-MBC, respectively. The adsorption processes were well fitted by the pseudo second-order kinetic model. Thermodynamic parameters showed that the adsorption of Cr(VI) onto both adsorbents was feasible, spontaneous, and exothermic under the studied conditions. The spent Co-Fe-MBC could be readily regenerated for reuse.  相似文献   

4.
The adsorption and desorption behavior of Cr(VI) in membrane capacitive deionization (MCDI) was investigated systematically in the presence of bovine serum albumin (BSA) and KCl with different concentrations, respectively. Results revealed that Cr(VI) absorption was enhanced and the adsorption amount for Cr(VI) increased from 155.7 to 190.8?mg/g when KCl concentration increased from 100 to 200?mg/L in the adsorption process, which was attributed to the stronger driving force. However, the adsorption amount sharply decreased to 90.2?mg/g when KCl concentration reached up to 1000?mg/L suggesting the negative effect for Cr(VI) removal that high KCl concentration had. As for the effect of BSA on ion adsorption, the amount for Cr (VI) significantly declined to 78.3?mg/g and pH was found to be an important factor contributing to this significant reduction. Then, the desorption performance was also conducted and it was obtained that the presence of KCl had negligible effect on Cr(VI) desorption, while promoted by the addition of BSA. The incomplete desorption was obtained and the residual chromium ions onto the electrode after desorption was detected via energy-dispersive X-ray spectroscopy (EDS). Based on above analysis, the enhanced removal mechanism for Cr(VI) in MCDI was found to be consisted of ion adsorption onto electrode surface, the redox reaction of Cr(VI) into Cr(III) and precipitation, which was demonstrated by X-ray photoelectron spectroscopy (XPS) and scanning electron microscope (SEM).  相似文献   

5.
Cr(Ⅲ) adsorption by biochars generated from peanut, soybean, canola and rice straws is investigated with batch methods. Adsorption of Cr(Ⅲ) increased as pH rose from 2.5 to 5.0. Adsorption of Cr(Ⅲ) led to peak position shifts in the FFIR-PAS spectra of the biochars and made zeta potential values less negative, suggesting the formation of surface complexes between Cr^3+ and functional groups on the biochars. The adsorption capacity of Cr(Ⅲ) followed the order: peanut straw char 〉 soybean straw char 〉 canola straw char 〉 rice straw char, which was consistent with the content of acidic functional groups on the biochars. The increase in Cr^3+ hydrolysis as the pH rose was one of the main reasons for the increased adsorption of Cr(Ⅲ) by the biochars at higher pH values. Cr(llI) can be adsorbed by the biochars through electrostatic attraction between negative surfaces and Cr^3+, but the relative contribution of electrostatic adsorption was less than 5%. Therefore, Cr(Ⅲ) was mainly adsorbed by the biochars through specific adsorption. The Langumir and Freundlich equations fitted the adsorption isotherms well and can therefore be used to describe the adsorption behavior of Cr(Ⅲ) by the crop straw biochars. The crop straw biochars have great adsorption capacities for Cr(Ⅲ) under acidic conditions and can be used as adsorbents to remove Cr(Ⅲ) from acidic wastewaters.  相似文献   

6.
Mg–Al–Cl layered double hydroxide(Cl-LDH) was prepared to simultaneously remove Cu(Ⅱ)and Cr(VI) from aqueous solution. The coexisting Cu(Ⅱ)(20 mg/L) and Cr(VI)(40 mg/L) were completely removed within 30 min by Cl-LDH in a dosage of 2.0 g/L; the removal rate of Cu(Ⅱ) was accelerated in the presence of Cr(VI). Moreover, compared with the adsorption of single Cu(Ⅱ) or Cr(VI), the adsorption capacities of Cl-LDH for Cu(Ⅱ) and Cr(VI) can be improved by 81.05% and 49.56%, respectively, in the case of coexisting Cu(Ⅱ)(200 mg/L) and Cr(VI)(400 mg/L). The affecting factors(such as solution initial p H, adsorbent dosage, and contact time) have been systematically investigated. Besides, the changes of p H values and the concentrations of Mg~(2+) and Al~(2+)in relevant solutions were monitored. To get the underlying mechanism, the Cl-LDH samples before and after adsorption were thoroughly characterized by X-ray powder diffraction, transmission electron microscopy, Fourier transform infrared spectroscopy, and X-ray photoelectron spectroscopy. On the basis of these analyses, a possible mechanism was proposed. The coadsorption process involves anion exchange of Cr(VI) with Cl-in Cl-LDH interlayer, isomorphic substitution of Mg~(2+) with Cu~(2+), formation of Cu_2Cl(OH)_3precipitation, and the adsorption of Cr(VI) by Cu_2Cl(OH)_3. This work provides a new insight into simultaneous removal of heavy metal cations and anions from wastewater by Cl-LDH.  相似文献   

7.
Uranium-reducing bacteria were immobilized with sodium alginate, anthraquinone-2, 6-disulfonate (AQDS), and carbon nanotubes (CNTs). The effects of different AQDS-CNTs contents, U(IV) concentrations, and metal ions on U(IV) reduction by immobilized beads were examined. Over 97.5% U(VI) (20 mg/L) was removed in 8 hr when the beads were added to 0.7% AQDS-CNTs, which was higher than that without AQDS-CNTs. This result may be attributed to the enhanced electron transfer by AQDS and CNTs. The reduction of U(VI) occurred at initial U(VI) concentrations of 10 to 100 mg/L and increased with increasing AQDS-CNT content from 0.1% to 1%. The presence of Fe(III), Cu(II) and Mn(II) slightly increased U(VI) reduction, whereas Cr(VI), Ni(II), Pb(II), and Zn(II) significantly inhibited U(VI) reduction. After eight successive incubation-washing cycles or 8 hr of retention time (HRT) for 48 hr of continuous operation, the removal efficiency of uranium was above 90% and 92%, respectively. The results indicate that the AQDS-CNT/AL/cell beads are suitable for the treatment of uranium-containing wastewaters.  相似文献   

8.
The study focused on the effect of several typical competing solutes on removal of arsenic with Fe_2O_3 and AL_2O_3.The test results indicate that chloride,nitrate and sulfate did not have detectable effects,and that selenium(Ⅳ)(Se(Ⅳ))and vanadium(Ⅴ)(V(Ⅴ)) showed slight effects on the adsorption of As(Ⅴ)with Fe_2O_3.The results also showed that adsorption of As(Ⅴ)on AL_2O_3 was not affected by chloride and nitrate anions,but slightly by Se(Ⅳ)and V(Ⅴ)ions.Unlike the adsorption of As(Ⅴ)with Fe_2O_3,that with Fe_2O_3 was affected by the presence of sulfate in water solutions.Both phosphate and silica have significant adverse effects on the adsorption of As(Ⅴ)adsorption with Fe_2O_3 and Al_2O_3.Compared to the other tested anions,phosphate anion was found to be the most prominent solute affecting the As(Ⅴ)adsorption with Fe_2O_3 and Al_2O_3.In general,Fe_2O_3 has a better performance than Al_2O_3 in removal of As(Ⅴ)within a water environment where multi competing solutes are present.  相似文献   

9.
We fabricated and characterized two hybrid adsorbents originated from hydrated ferric oxides(HFOs) using a polymeric anion exchanger D201 and calcite as host. The resultant adsorbents(denoted as HFO-201 and IOCCS) were employed for Sb(V) removal from water. Increasing solution pH from 3 to 9 apparently weakened Sb(V) removal by both composites, while increasing temperature from 293 to 313 K only improved Sb(V) uptake by IOCCS. HFO-201 exhibited much higher capacity for Sb(V) than for IOCCS in the absence of other anions in solution. Increasing ionic strength from 0.01 to 0.1 mol/L NaNO3would result in a significant drop of the capacity of HFO-201 in the studied pH ranges; however, negligible effect was observed for IOCCS under similar conditions. Similarly, the competing chloride and sulfate pose more negative effect on Sb(V) adsorption by HFO-201 than by IOCCS, and the presence of silicate greatly decreased their adsorption simultaneously, while calcium ions were found to promote the adsorption of both adsorbents. XPS analysis further demonstrated that preferable Sb(V) adsorption by both hybrids was attributed to the inner sphere complexation of Sb(V) and HFO, and Ca(II) induced adsorption enhancement possibly resulted from the formation of HFO-Ca-Sb complexes. Column adsorption runs proved that Sb(V) in the synthetic water could be effectively removed from 30 μg/L to below 5 μg/L(the drinking water standard regulated by China), and the effective treatable volume of IOCCS was around 6 times as that of HFO-201, implying that HFO coatings onto calcite might be a more effective approach than immobilization inside D201.  相似文献   

10.
The adsorption and desorption behavior of Cr(Ⅵ) in membrane capacitive deionization(MCDI) was investigated systematically in the presence of bovine serum albumin(BSA) and KCl with different concentrations, respectively. Results revealed that Cr(Ⅵ) absorption was enhanced and the adsorption amount for Cr(Ⅵ) increased from 155.7 to 190.8 mg/g when KCl concentration increased from 100 to 200 mg/L in the adsorption process, which was attributed to the stronger driving force. However, the adsorption amount sharply decreased to 90.2 mg/g when KCl concentration reached up to 1000 mg/L suggesting the negative effect for Cr(Ⅵ) removal that high KCl concentration had. As for the effect of BSA on ion adsorption, the amount for Cr(Ⅵ) significantly declined to 78.3 mg/g and p H was found to be an important factor contributing to this significant reduction. Then, the desorption performance was also conducted and it was obtained that the presence of KCl had negligible effect on Cr(Ⅵ) desorption, while promoted by the addition of BSA. The incomplete desorption was obtained and the residual chromium ions onto the electrode after desorption was detected via energy-dispersive X-ray spectroscopy(EDS). Based on above analysis, the enhanced removal mechanism for Cr(Ⅵ) in MCDI was found to be consisted of ion adsorption onto electrode surface, the redox reaction of Cr(Ⅵ) into Cr(III)and precipitation, which was demonstrated by X-ray photoelectron spectroscopy(XPS) and scanning electron microscope(SEM).  相似文献   

11.
重金属铬(Cr(VI))是废水中常见的、困扰很多污水生物处理系统运行效果的污染物.本文通过静态试验和静态冲击试验,研究了Cr(VI)在活性污泥系统中的分布特点和对硝化效率、活性等的影响,并进行了模型分析.结果表明,活性污泥对Cr的吸附很快,但吸附量有限,Cr(VI)投加浓度为1、5、10和30 mg · L-1的溶液中,Cr的12 h-吸附量分别为0.79、1.98、3.19和5.78 mg · g-1.Cr(VI)投加到活性污泥混合液中后形态分为溶解态、可洗脱和不可洗脱态,可洗脱的Cr能够向不可洗脱态转变.Cr(VI)对活性污泥硝化活性的抑制程度随着Cr(VI)浓度的增大而提高.静态试验中,1、3、5、10和30 mg · L-1 Cr(VI)对氨氮平均降解速率的抑制率分别为5.25%、9.80%、10.41%、17.54%和21.38%.Cr(VI)对微生物的抑制作用大小是:氨氧化菌 >亚硝酸盐氧化菌 >异养菌.模型分析发现,Cr(VI)对氨氧化菌和异养菌比耗氧速率的抑制符合Haldane动力学模型,属于非竞争性抑制.冲击试验表明Cr对硝化等的抑制主要是不可洗脱的Cr造成的,抑制效果的出现具有滞后性.  相似文献   

12.
地聚合物(Geopolymer,简称GP)是由含硅铝酸盐的偏高岭土(Metakaolin,简称MK)或固体废料(如粉煤灰)经碱性激活制备的立体网状结构无机聚合物,对大部分重金属阳离子有良好的吸附作用,但对以阴离子形态存在的重金属吸附效果很差.本研究以偏高岭土为主要原料制备GP,同时用CTAB进行改性,研究其化学组成变化及对典型以阴、阳离子形态存在的重金属Cr(VI)和Cu(II)的同时吸附作用.结果表明,pH为5、吸附时间为24 h、初始浓度为50 mg·L-1、吸附剂投加量为1 g·L-1时,CTAB-GP对Cu(II)的去除率达到98.6%,Cr(VI)的最高去除率为25.6%,同时还发现溶液中Cu(II)的存在对吸附Cr(VI)有较大促进作用.整体来看,两种金属混合吸附时很好地符合二级动力学规律,单溶质吸附很好地符合Langmuir和Freundlich等温式,Cu(II)和Cr(VI)的理论最大吸附量分别为147.1 mg·g-1和63.1 mg·g-1.XRD、FTIR和BET表征分析结果表明,CTAB-GP中即使存在季铵盐阳离子,但依然属于地聚合物.CTAB-GP可以不牺牲对重金属阳离子吸附性能的同时吸附阴离子,优于常规地聚合物,鉴于CTAB-GP的这种特性,其在重金属污染防治中显示出极大的应用前景.  相似文献   

13.
BS+DAS复配修饰膨润土吸附Cr(Ⅵ)和Cd2+的研究   总被引:1,自引:0,他引:1       下载免费PDF全文
为了研究两性-阴离子复配修饰膨润土对Cr(VI)和Cd2+的吸附性能差异及其机理,并为两性复配修饰黏土矿物治理重金属污染水体提供依据,采用阴离子型有机修饰剂1-癸烷磺酸钠(DAS)复配修饰两性修饰剂十二烷基二甲基甜菜碱(BS-12或BS)修饰膨润土,研究各供试土样对Cr(VI)和Cd2+的等温吸附曲线及不同温度、pH值和离子强度条件对吸附的影响.结果表明,Langmuir模型能较好地拟合各修饰土样对不同类型重金属离子(Cr(VI)和Cd2+)的吸附曲线,其对Cr(VI)和Cd2+的平衡吸附量均呈现BS+150DAS(150%CEC DAS复配修饰膨润土)BS+100DASBS+50DASBS+25DASBSCK(膨润土)的趋势,且对Cr(VI)、Cd2+的最大吸附量(qm)分别为85.92 mmol·kg-1(100BS+150DAS)和321.89 mmol·kg-1(100BS+150DAS).各供试土样对Cr(VI)和Cd2+的吸附均表现为自发、焓增和熵增的特征,升温可增加其对Cr(VI)和Cd2+的最大吸附量.酸性环境有利于各修饰土样对Cr(VI)的吸附,而不利于对Cd2+的吸附.离子强度增加均降低了各修饰土样对Cr(VI)和Cd2+的吸附.  相似文献   

14.
A Gram-negative, chromium(VI) tolerant and reductive strain CTS-325, isolated from a Chinese chromate plant, was identified as Ochrobactrum anthropi based on its biochemical properties and 16S rDNA sequence analysis. It was able to tolerate up to 10 mmol/L Cr(VI) and completely reduce 1 mmol/L Cr(VI) to Cr(III) within 48 h. When the strain CTS-325 was induced with Cr(VI), a protein increased significantly in the whole cell proteins. Liquid chromatography tandem mass spectrometry (LC-MS/MS) analysis revealed that this protein was a superoxide dismutase (SOD) homology. The measured superoxide dismutase activity was 2694 U/mg after three steps of purification. The SOD catalyzes the dismutation of the superoxide anion (O2·−) into hydrogen peroxide and molecular oxygen. This protein is considered to be one of the most important anti-oxidative enzymes for O. anthropi as it allows the bacterium to survive high oxygen stress environments, such as the environment produced during the reduction process of Cr(VI).  相似文献   

15.
采用从活性污泥中筛选的ZYL霉菌,进行吸附水体中Cr(Ⅵ)、Cd(Ⅱ)离子研究。研究结果表明:在Cr(Ⅵ)、Cd(Ⅱ)浓度分别为300mg/L时,菌种生长良好。吸附水体中[Cr(Ⅵ)、Cd(Ⅱ)]的最佳条件是pH=5.0,时间1h,温度为10℃。吸附规律符合Langm uir等温吸附模型,由回归方程得到Cr(Ⅵ)的表观最大吸附量为14m g/g;Cd(Ⅱ)的表观最大吸附量为52m g/g,说明该霉菌可以很好的去除低温水体(地下水)中Cr(Ⅵ)、Cd(Ⅱ)离子。  相似文献   

16.
铁锰复合氧化物吸附去除五价锑性能研究   总被引:11,自引:2,他引:9       下载免费PDF全文
对比研究了铁锰复合氧化物(FMBO)、羟基氧化铁(FeOOH)和二氧化锰(MnO2)吸附去除五价锑(Sb(V))的性能.结果表明FMBO对Sb(V)具有很好的吸附性能,在pH=5.0的条件下,最大吸附容量达到1.05 mmol·g-1,略高于FeOOH (0.82 mmol·g-1)及远高于MnO2 (0.43 mmol·g-1);采用Freundlich模型可以很好地描述Sb(V)在FMBO的吸附行为(R2 = 0.98).就吸附动力学而言,假二级动力学可很好地描述Sb(V)在FMBO (R2 = 0.93)和MnO2表面的吸附过程(R2 = 0.96),而Sb(V)在FeOOH表面的吸附过程可用Elovich模型拟合 (R2 = 0.94).Sb(V)的吸附量随着pH值的升高而降低;磷酸盐显著抑制了Sb(V)的吸附,而硫酸盐和碳酸盐影响不大.提高体系离子强度可促进Sb(V)在FMBO表面的吸附,推断Sb(V)在FMBO表面形成内层络合物后被吸附去除.  相似文献   

17.
A fibrous strong base anion exchanger (QAPPS) was prepared for the first time via chloromethylation and quaternary amination reaction of polyphenylene sulfide fiber (PPS), and its physical-chemical structure and adsorption behavior for Cr(VI) were characterized by FT-IR, Energy Dispersive Spectrometry, TG-DTG, elemental analysis and batch adsorptive technique, respectively. The novel fibrous adsorbent could effectively adsorb Cr(VI) over the pH range 1-12, the maximum adsorption capacity was 166.39 mg/g at pH 3.5, and the adsorption behavior could be described well by Langmuir isotherm equation model. The adsorption kinetics was studied using pseudo first-order and pseudo second-order models, and the t1/2 and equilibrium adsorption time were 5 and 20 min respectively when initial Cr(VI) concentration was 100 mg/L. The saturated fibers could be regenerated rapidly by a mixed solution of 0.5 mol/L NaOH and 0.5 mol/L NaCl, and the adsorption capacity was well maintained after six adsorption-desorption cycles.  相似文献   

18.
本文通过吸附平衡和动力学实验方法对Sb(V)在锑矿冶炼区周边土壤表面开展吸附行为研究,用常用的等温吸附模型和动力学吸附模型分别对等温吸附曲线和动力学吸附曲线进行拟合。结果表明:Langmuir与Freundlich模型对荒地土和林地土吸附Sb(Ⅴ)的等温吸附曲线均有较好的拟合效果,拟合系数R20.988。荒地土对Sb(Ⅴ)的吸附能力大于林地土,其吸附量是林地土的2.9±0.2倍,这与Langmuir模型预测的该两种土壤的吸附倍数相当,荒地土表现出强烈吸附Sb(Ⅴ)的能力,尤其在锑浓度较高的体系中更为明显。结合土壤基本理化性质及矿物学特征,认为土壤秥粒、铁矿物和碳酸钙是影响土壤吸附Sb(V)的主要因素。有机质对土壤吸附Sb(Ⅴ)有一定促进作用,但这种影响只表现在Sb(Ⅴ)初始浓度低的条件下;而在Sb(Ⅴ)初始浓度高的条件下,有机质对土壤吸附Sb(Ⅴ)的影响不明显。土壤吸附Sb(Ⅴ)的过程分为快速吸附和慢速吸附两个阶段,快速反应发生在70 min以内。初始浓度低(0.01 mmol/L)的条件下,Elovich方程能够很好地拟合荒地土和林地土吸附Sb(V)的动态曲线;初始浓度高(2 mmol/L)的条件下,双常数方程对荒地土吸附Sb(V)的拟合效果较好,拟一级动力学方程和拟二级动力学方程则适用于拟合林地土吸附Sb(V)的过程。  相似文献   

19.
Mg–Al–Cl layered double hydroxide (Cl-LDH) was prepared to simultaneously remove Cu(II) and Cr(VI) from aqueous solution. The coexisting Cu(II) (20 mg/L) and Cr(VI) (40 mg/L) were completely removed within 30 min by Cl-LDH in a dosage of 2.0 g/L; the removal rate of Cu(II) was accelerated in the presence of Cr(VI). Moreover, compared with the adsorption of single Cu(II) or Cr(VI), the adsorption capacities of Cl-LDH for Cu(II) and Cr(VI) can be improved by 81.05% and 49.56%, respectively, in the case of coexisting Cu(II) (200 mg/L) and Cr(VI) (400 mg/L). The affecting factors (such as solution initial pH, adsorbent dosage, and contact time) have been systematically investigated. Besides, the changes of pH values and the concentrations of Mg2+ and Al3+ in relevant solutions were monitored. To get the underlying mechanism, the Cl-LDH samples before and after adsorption were thoroughly characterized by X-ray powder diffraction, transmission electron microscopy, Fourier transform infrared spectroscopy, and X-ray photoelectron spectroscopy. On the basis of these analyses, a possible mechanism was proposed. The coadsorption process involves anion exchange of Cr(VI) with Cl in Cl-LDH interlayer, isomorphic substitution of Mg2+ with Cu2+, formation of Cu2Cl(OH)3 precipitation, and the adsorption of Cr(VI) by Cu2Cl(OH)3. This work provides a new insight into simultaneous removal of heavy metal cations and anions from wastewater by Cl-LDH.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号