Fluoride removal by Al, Ti, and Fe hydroxides and coexisting ion effect

Batch experiments were conducted to evaluate fluoride removal by Al,Fe,and Ti-based coagulants and adsorbents,as well as the effects of coexisting ions and formation of aluminum–fluoride complexes on fluoride removal by co-precipitation with alum(Al_2(SO_4)_3·18H_2O).Aluminum sulfate was more efficient than the other coagulants for fluoride removal in the pH range between 6 and 8.Nano-crystalline TiO_2 was more effective for fluoride removal than Al and Fe hydroxides in a pH range of 3–5.Coexisting anions in water decreased the removal of fluoride in the order:phosphate(2.5 mg/L) arsenate(0.1 mg/L) bicarbonate(200 mg/L) sulfate(100 mg/L) = nitrate(100 mg/L) silicate(10 mg/L) at a pH of 6.0.The effect of silicate became more significant at pH 7.0.Calcium and magnesium improved the removal of fluoride.Zeta-potential measurements determined that the adsorption of fluoride shifted the PZC of Al(OH)_3 precipitates from 8.9 to 8.4,indicating the chemical adsorption of fluoride at the surface.The presence of fluoride in solution significantly increased the soluble aluminum concentration at pH 6.5.A Visual MINTEQ modeling study indicated that the increased aluminum solubility was caused by the formation of AlF~(2+),AlF~(+2),and AlF_3complexes.The AlF_x complexes decreased the removal of fluoride during co-precipitation with aluminum sulfate.     

Effects of Ca(OH)2 assisted aluminum sulfate coagulation on the removal of humic acid and the formation potentials of tri-halomethanes and haloacetic acids in chlorination

The effects of addition of calcium hydroxide on aluminum sulphate(or alum) coagulation for removal of natural organic matter(NOM) and its subsequent effect on the formation potentials of two major types of regulated disinfection byproducts(DBPs),haloacetic acids(HAAs) and trihalomethanes(THMs),have been examined.The results revealed several noteworthy phenomena.At the optimal coagulation pH(i.e.6),the coagulation behavior of NOM water solutions versus alum dose,showed large variation and a consequent great change in the formation potentials of the DBPs at certain coagulant doses.However,with addition of a relatively small amount of Ca(OH) 2,although the zeta potential of coagulated flocs remained almost the same,NOM removal became more consistent with alum dose.Importantly,also the detrimental effect of charge reversal on NOM removal at the low coagulant dose disappeared.This resulted in a steady decrease in the formation potentials of DBPs as a function of the coagulant dose.Moreover,the addition of Ca(OH) 2 broadened the pH range of alum coagulation and promoted further reduction of the formation potentials of the DBPs.The enhancement effects of Ca(OH) 2 assisted alum coagulation are especially pronounced at pH 7 and 8.Finally,synchronous fluorescence spectra showed that the reduction in DBPs formation potential by Ca(OH) 2-assisted alum coagulation was connected to an enhanced removal of small hydrophobic and hydrophilic HA molecules.Ca(OH) 2-assistance of alum coagulation appeared to increase substantially the removal of the hydrophilic HA fraction responsible for HAAs formation,prompting further reduction of HAA formation potentials.     

Phosphate removal from domestic wastewater using thermally modified steel slag

This study was performed to investigate the removal of phosphate from domestic wastewater using a modified steel slag as the adsorbent. The adsorption effects of alkalinity, salt, water,and thermal modification were investigated. The results showed that thermal activation at 800℃ for 1 hr was the optimum operation to improve the adsorption capacity. The adsorption process of the thermally modified slag was well described by the Elovich kinetic model and the Langmuir isotherm model. The maximum adsorption capacity calculated from the Langmuir model reached 13.62 mg/g. Scanning electron microscopy indicated that the surface of the modified slag was cracked and that the texture became loose after heating. The surface area and pore volume did not change after thermal modification. In the treatment of domestic wastewater, the modified slag bed(35.5 kg) removed phosphate effectively and operated for 158 days until the effluent P rose above the limit concentration of 0.5 mg/L. The phosphate fractionation method, which is often applied in soil research, was used to analyze the phosphate adsorption behavior in the slag bed. The analysis revealed that the total contents of various Ca–P forms accounted for 81.4%–91.1%, i.e., Ca10–P 50.6%–65.1%, Ca8–P 17.8%–25.0%,and Ca2–P 4.66%–9.20%. The forms of Al–P, Fe–P, and O–P accounted for only 8.9%–18.6%. The formation of Ca10–P precipitates was considered to be the main mechanism of phosphate removal in the thermally modified slag bed.     

Phosphate removal and recovery through crystallization of hydroxyapatite using xonotlite as seed crystal

Xonotlite was synthesized and tested for phosphate removal and recovery from synthetic solution in a batch mode. The e ects of pH, initial calcium concentration, bicarbonate concentration on phosphate removal through crystallization were examined. The morphology and X-ray di raction (XRD) pattern of xonotlite before and after crystallization confirmed the formation of crystalline hydroxyapatite. The results indicated that the crystallization product had a very high P content (> 10%), which is comparable to phosphate rock at the dosage of 50–200 mg xonotlite per liter, with a maximum P content of 16.7%. The kinetics of phosphate removal followed the second-order reaction equation. The phosphate removal ability increased with increasing pH. The precipitation of calcium phosphate took place when pH was higher than 7.2, whereas the crystallization occurred at pH 6.0. A high calcium concentration could promote the removal of phosphate via crystallization, while a high bicarbonate concentration also enhanced phosphate removal, through that the pH was increased and thus induced the precipitation process. When xonotlite was used to remove phosphate from wastewater, the removal e ciency could reach 91.3% after 24 h reaction, with removal capacity 137 mg/g. The results indicated that xonotlite might be used as an e ective crystal seed for the removal and recovery of phosphate from aqueous solution.     

Investigating the coagulation of non-proteinaceous algal organic matter: Optimizing coagulation performance and identification of removal mechanisms

The removal of algal organic matter(AOM) is a growing concern for the water treatment industry worldwide. The current study investigates coagulation of non-proteinaceous AOM(AOM after protein separation), which has been minimally explored compared with proteinaceous fractions. Jar tests with either aluminum sulphate(alum) or polyaluminium chloride(PACl) were performed at doses of 0.2–3.0 mg Al per 1 mg of dissolved organic carbon in the p H range 3.0–10.5. Additionally, non-proteinaceous matter was characterized in terms of charge, molecular weight and carbohydrate content to assess the treatability of its different fractions. Results showed that only up to 25% of non-proteinaceous AOM can be removed by coagulation under optimized conditions. The optimal coagulation p H(6.6–8.0 for alum and 7.5–9.0 for PACl) and low surface charge of the removed fraction indicated that the prevailing coagulation mechanism was adsorption of non-proteinaceous matter onto aluminum hydroxide precipitates. The lowest residual Al concentrations were achieved in very narrow p H ranges, especially in the case of PACl. High-molecular weight saccharidelike organics were amenable to coagulation compared to low-molecular weight( 3 k Da)substances. Their high content in non-proteinaceous matter(about 67%) was the reason for its low removal. Comparison with our previous studies implies that proteinaceous and nonproteinaceous matter is coagulated under different conditions due to the employment of diverse coagulation mechanisms. The study suggests that further research should focus on the removal of low-molecular weight AOM, reluctant to coagulate, with other treatment processes to minimize its detrimental effect on water safety.     

Exfoliated Mg–Al–Fe layered double hydroxides/polyether sulfone mixed matrix membranes for adsorption of phosphate and fluoride from aqueous solutions

Mg–Al–Fe layered double hydroxides(LDHs) were exfoliated and incorporated in polyether sulfone membranes for the removal of phosphate and fluoride for the first time. The exfoliation methods, coagulation bath, LDH amount, interfering ions, adsorption isotherm,desorption and reuse of the membranes were investigated. It was found that LDHs could be quickly exfoliated in formamide/N,N-dimethylformamide(DMF) solvent mixtures with sodium carboxymethyl cellulose as a stabilizer. The membranes displayed much higher adsorption capacity for phosphate(5.61 mg/g) and faster adsorption rate than the unexfoliated materials. With increased DMF content in the coagulation bath, the static and dynamic adsorption capacity rose. Interference from Cl-and SO_4~(2-)(50 mg/L) on adsorption of phosphates was not apparent. The membranes displayed excellent reusability in dynamic adsorption/desorption. The membranes also showed high adsorption capacity for fluorides(1.61 mg/g).     

Preparation and coagulation efficiency of polyaluminium ferric silicate chloride composite coagulant from wastewater of high-purity graphite production

The aim of the present work was to produce a polyaluminium ferric silicate chloride (PAFSiC) coagulant from acidic and alkaline wastewater of purifying graphite by roasting, and subsequently to evaluate coagulation efficiency of the reagent by treating surface water from the Yellow River as well as municipal wastewater in comparison with the conventional coagulant polyaluminium chloride (PAC). The PAFSiC coagulant was prepared by co-polymerization. The effects of (Al+Fe)/Si molar ratio, OH/(Al+Fe) molar ratio (i.e., value), coagulant dosage and pH value of test suspension on the coagulation behavior of FAFSiC and the stability of the PAFSiC were also examined. Results showed that PAFSiC performed more efficiently than PAC in removing turbidity, chemical oxygen demand (COD), and total phosphate (TP). The PAFSiC with a value of 2.0 and (Al+Fe)/Si ratio of 5 (PAFSiC 2.0/5) showed excellent coagulation effect for both turbidity and COD, while PAFSiC 1.0/5 was the best for TP. The optimum coagulation pH range of PAFSiC 2.0/5 was 5.0–9.0, slightly wider than that of PAC (6.0–8.0). The process can be easily incorporated into high-purity graphite production plants, thereby reducing wastewater pollution and producing a valuable coagulant.     

Preferential binding between intracellular organic matters and Al13 polymer to enhance coagulation performance

Coagulation is the best available method for removing intracellular organic matter (IOM), which is released from algae cells and is an important precursor to disinfection by-products in drinking water treatment. To gain insight into the best strategy to optimize IOM removal, the coagulation performance of two Al salts, i.e., aluminum chloride (AlCl₃) and polyaluminum chloride (PACl, containing 81.2% Al₁₃), was investigated to illuminate the effect of Al species distribution on IOM removal. PACl showed better removal efficiency than AlCl₃ with regard to the removal of turbidity and dissolved organic carbon (DOC), owing to the higher charge neutralization effect and greater stability of pre-formed Al₁₃ species. High pressure size exclusion chromatography analysis indicated that the superiority of PACl in DOC removal could be ascribed to the higher binding affinity between Al₁₃ polymer and the low and medium molecular weight (MW) fractions of IOM. The results of differential log-transformed absorbance at 254 and 350?nm indicated more significant formation of complexes between AlCl₃ and IOM, which benefits the removal of tryptophan-like proteins thereafter. Additionally, PACl showed more significant superiority compared to AlCl₃ in the removal of < 5?kDa and hydrophilic fractions, which are widely viewed as the most difficult to remove by coagulation. This study provides insight into the interactions between Al species and IOM, and advances the optimization of coagulation for the removal of IOM in eutrophic water.     

Simultaneous pyridine biodegradation and nitrogen removal in an aerobic granular system

Simultaneous pyridine biodegradation and nitrogen removal were successfully achieved in a sequencing batch reactor(SBR) based on aerobic granules. In a typical SBR cycle, nitritation occurred obviously after the majority of pyridine was removed, while denitrification occurred at early stage of the cycle when oxygen consumption was aggravated. The effect of several key operation parameters, i.e., air flow rate, influent NH_4~+-N concentration,influent p H and pyridine concentration, on nitritation, pyridine degradation and total nitrogen(TN) removal, was systematically investigated. The results indicated that high air flow rate had a positive effect on both pyridine degradation and nitritation but a negative impact of overhigh air flow rate. With the increase of NH_4~+ dosage, both nitritation and TN removal could be severely inhibited. Slightly alkaline condition, i.e., pH 7.0–8.0, was beneficial for both pyridine degradation and nitritation. High pyridine dosage often resulted in the delay of both pyridine degradation and nitritation. Besides, extracellular polymeric substances production was affected by air flow rate, NH_4~+ dosage, pyridine dosage and p H.In addition, high-throughput sequencing analysis demonstrated that Bdellovibrio and Paracoccus were the dominant species in the aerobic granulation system. Coexistence of pyridine degrader, nitrification related species, denitrification related species, polymeric substances producer and self-aggregation related species was also confirmed by highthroughput sequencing.     

Algal removal from cyanobacteria-rich waters by preoxidation-assisted coagulation–flotation: Effect of algogenic organic matter release on algal removal and trihalomethane formation

The cyanobacteria-bloom in raw waters frequently causes an unpredictable chemical dosing of preoxidation and coagulation for an effective removal of algal cells in water treatment plants. This study investigated the effects of preoxidation with NaOCl and ClO_2 on the coagulation-flotation effectiveness in the removal of two commonly blooming cyanobacteria species, Microcystis aeruginosa(MA) and Cylindrospermopsis raciborskii(CR), and their corresponding trihalomethane(THM) formation potential. The results showed that dual dosing with NaOCl plus ClO_2 was more effective in enhancing the deformation of cyanobacterial cells compared to single dosing with Na OCl, especially for CR-rich water.Both preoxidation approaches for CR-rich water effectively reduced the CR cell count with less remained dissolved organic carbon(DOC), which benefited subsequent coagulation–flotation. However, preoxidation led to an adverse release of algogenic organic matter(AOM) in the case of MA-rich water. The release of AOM resulted in a poor removal in MA cells and a large amount of THM formation after oxidation-assisted coagulation-flotation process. The reduction in THM formation potential of CR-rich waters is responsible for effective algae and DOC removal by alum coagulation. It is concluded that the species-specific characteristic of cyanobacteria and their AOM released during chlorination significantly influences the performance of coagulation–flotation for AOM removal and corresponding THM formation.     

国际化学危险品分类体系简介

介绍了当前国际化学危险品的各种分类体系,对比了GHS与TDG、EU_CLP、DOT、WHMIS等对化学危险品的具体分类。有助于GHS的理解与掌握,全面推进GHS在我国的实施。     

多目标规划在预测区域总产值-排污-水质协调解中的应用研究

以某区域水环境－经济系统为研究实例，寻求值－排污－水质综合协调解方法，寻求净收益最大时的总体规划方案。建立目标参数规划模型，寻求不同生产规模条件下的产值－排污－水质协调解，又探讨了水环境标准约束下的某化工区废水治理费用的计算方法，提出了以供决策者选择的方案。     

滇池富营养化特性评价

介绍了滇池水质状况,对滇池富营养化特性进行了分析和评价,并提出了对策.     

土壤整体质量的生态毒性评价

土壤样品采自沈阳西部污灌区 .进行了污染物 (重金属和矿物油 )含量分析和生态毒性试验 .重金属采用原子吸收分光光度仪测定 ,矿物油采用紫外分光光度计测定 .生态毒性试验分别参照国际标准组织 (ISO)和OECD指南 ,进行了植物毒性试验、蚯蚓毒性试验和蚕豆根尖微核试验 .植物试验以小麦种子发芽根伸长抑制率为试验终点 ,试验周期50h ,蚯蚓毒性试验以蚯蚓死亡率、体重增长抑制率为试验终点 ,试验周期28d .土壤中矿物油含量在145mg/kg～1121mg/kg ,重金属Cd为0.34mg/kg～1.81mg/kg .土壤对植物和蚯蚓显示不同程度的毒性效应 ,土壤的蚕豆根尖微核率明显高于对照 .种子发芽根伸长抑制率为2.0%至-35.1% ,蚯蚓死亡率为0%～40%.体重增长抑制率由14d的-2.3%～-19.4%在28d增加到-2.1%～10.7% ,蚕豆根尖微核率最高达6.62/100.研究表明 ,土壤中的污染物积累较低 ,但具有明显的生态毒性 .     

哈尔滨松北区城市湿地的生态安全分析

以哈尔滨松北区城市湿地为研究对象,选择10个指标,采用因子分析法和聚类分析法,研究了松花江发生污染事故前后城市湿地的生态安全状况.结果表明:发生污染前哈尔滨松北区城市湿地东区的生态安全程度最高,发生污染后中区的生态安全程度最低;西区的抗干扰能力较差.各主因子中以水因子的下降幅度最大,说明水污染直接影响了哈尔滨松北区城市湿地的生态安全.最后有针对性地提出了哈尔滨松北区城市湿地的生态安全对策.     

学生食堂优化管理的数学模型

从学生食堂的设备及场所、物资的储存与购入、工作人员的管理及就餐者对食堂的要求这4个方面描述了各自对学生食堂管理的影响,得出了评估学生食堂优劣的一般公式Y=n∑i=1ωixi,并着重解决了学生就餐排队等待时间太长的问题,分析了该等待问题在排队论中所属的模型,解决了该课题要研究的问题的一般情况和个别案例,确定了各参数之间的关系.通过分析,得出了最优排队模型、费用模型及服务台数,并证明了最优模型的一般性.     

石脑油罐压力安全阀泄漏的隐患治理

石脑油罐压力安全阀泄漏，严重威胁生产与施工的安全进行。通过拆检，弄清了安全阀泄漏的原因，采取了相应措施，彻底解决了这一重大安全隐患。     

后勤装备防腐涂层加速试验环境谱研究

结合后勤装备服役特点,综合考虑亚热带沿海地区湿热、紫外光照、盐雾等主要腐蚀因素的影响,建立了适用于后勤装备表面涂层的加速试验环境谱,给出了各环境块的具体确定方法,并且提出了建立加速谱与装备实际使用环境的当量加速关系的方法。为后勤装备外露关键部位涂层使用寿命评定、涂层有效性检验和腐蚀修理方案制定提供了重要的依据。     

乌海市城区环境噪声现状分析

对乌海市《城市区域环境噪声标准》适用区域进行了划分,以乌海市2011年城区环境噪声监测统计数据为基础,分析了乌海市暴露在不同等效声级下的城区面积分布状况和达标情况。     

烟气脱硫副产物的综合利用

通过分析烟气脱硫石膏的性能 ,介绍了脱硫石膏的利用情况和研究进展 ,利用脱硫石膏生产建筑材料 ,如 β石膏和α石膏的工艺日臻成熟 ,利用脱硫石膏生产水泥辅料已进入工业化 ,而利用脱硫石膏生产充填尾砂胶结剂已经完成试验阶段 ,脱硫石膏在农业上也有很广泛的用途。