Life-cycle environmental and economic impacts of energy-crop fuel-chains: an integrated assessment of potential GHG avoidance in Ireland

This paper combines life-cycle analyses and economic analyses for Miscanthus and willow heat and electricity fuel-chains in Ireland. Displaced agricultural land-uses and conventional fuels were considered in fuel-chain permutations. Avoided greenhouse gas (GHG) emissions ranged from 7.7 to 35.2 t CO₂ eq. ha⁻¹ a⁻¹. Most fuel-chain permutations exhibited positive discounted financial returns, despite losses for particular entities at a farm-gate processed-biomass price of €100 t⁻¹ dry-matter. Attributing a value of €10 t⁻¹ CO₂ eq. to avoided GHG emissions, but subtracting financial returns associated with displaced fuel supplies, resulted in discounted annual national economic benefits (DANEBs) ranging from −457 to 1887€ ha⁻¹ a⁻¹. Extrapolating a plausible combination of fuel-chains up to a national indicative scenario resulted in GHG emission avoidance of 3.56 Mt CO₂ eq. a⁻¹ (5.2% of national emissions), a DANEB of 167 M€, and required 4.6% of national agricultural land area. As cost-effective national GHG avoidance options, Miscanthus and willow fuel-chains are robust to variation in yields and CO₂ price, and appear to represent an efficient land-use option (e.g. compared with liquid biofuel production). Policies promoting utilisation of these energy-crops could avoid unnecessary, and environmentally questionable, future purchase of carbon credits, as currently required for national Kyoto compliance.     

The holistic impact of integrated solid waste management on greenhouse gas emissions in Phuket

Continually increasing amounts of municipal solid waste (MSW) and the limited capacity of the existing waste management system in Phuket have led to the consideration of integrated waste management system (IWMS). Life cycle assessment (LCA) was employed to compare the greenhouse gas emissions expressed as global warming potential (GWP) of the existing waste management system (the base scenario) and other three IWMSs for Phuket MSW. Besides incineration and landfilling, the proposed scenarios include 30% source separation for recycling (scenario 2), anaerobic digestion (scenario 3) and both (scenario 4).The functional unit is set as 1 t of Phuket MSW treated. Results from the impact assessment of the base scenario shows that the net GWP is 1006 kg CO₂ equivalent. Landfilling contributes to the highest potentials of this impact. The results from a holistic comparison show that scenario 4 is the best option among all the scenarios, contributing GWP of 415 kg CO₂ eq., whereas the base scenario is the worst. The emission of greenhouse gas from landfilling is reduced by the introduction of landfill gas recovery and utilization for electricity production. By assumption, 50% recovery of landfill gas leads to the GWP reduction around 58% by total GWP of landfilling and 36% by the net GWP of the whole system in the base scenario. The study suggests that a policy that promotes source separation should be pursued, preferably combined with the application of landfill gas recovery for electricity. Policy promoting recycling is favorable over anaerobic digestion in the situation that both treatment systems could not be established at the same time. The major conclusion from the study is that results from the LCA can support Phuket Municipality for decision-making with respect to planning and optimizing IWMS. It can benefit other municipalities or policy makers to apply in their waste management projects.     

Economic evaluation of optional recycling processes for waste electronic home appliances

This paper presents an economic evaluation of three typical recycling processes for the five main types of waste electronic home appliances (EHA) (TV set, refrigerator, washing machine, air conditioner and personal computer) in Beijing, the capital of China. The main purpose is to identify the formal management framework with economic feasibility for the waste EHA generated in large municipalities of China. It is found that the advanced technologies, which have mechanical processing units, should be introduced to recover more valuable materials from the waste appliances. Net revenues with a range of 90–240 RMB (Chinese currency unit, 1.0 USD ≈ 8.0 RMB) per unit, depend on the type of appliance, could be expected in case of using the most complicated procedures which can separate both metals and plastics from the shredded mixtures. However, the recycling of waste refrigerator and waste washing machine will, respectively, spend about 100 and 6 RMB per unit if solely by simple manual dismantling. Revenues from recycling of the other three types of appliances are positive but quite low in this case. Although positive revenues could be achieved from the isolated evaluation of recycling, the entire management system, which also covers the phases of collection and transportation, is economically infeasible if the waste appliances are bought from the households still at current prices. Based on a survey of the householder's attitude to the cost for waste EHA management, which was conducted earlier, the practical way to construct a formal management system for waste EHA in Beijing is to reduce the citizen's traditional expectation to the values of waste appliances and encourage their transfer to the formal collection system at lower prices.     

Assessing the recycling potential of glass fibre reinforced plastic waste in concrete and cement composites

At present glass fibre reinforced plastic (GRP) waste recycling worldwide is very limited due to its intrinsic thermoset properties, lack of characterisation data and non availability of viable recycling and recovery routes. In the present study, efforts were made to recycle GRP waste powder and fibre in concrete and cement composites and assess its quality to comply with the British standards for use in construction applications. Results revealed that the mean compressive strength of concrete composites using 5%–50% GRP waste powder under water curing varied from 37 N/mm² to 19 N/mm². Increase in the concentration of GRP waste decreased the compressive strength. However, increase in curing duration (14–180 days) resulted in improving the compressive strength of concrete with 5% GRP application to 45.75 N/mm². Moreover, the density of concrete with 50% GRP waste was reduced by about 12% as compared to the control sample. The bending strength in terms of modules of rupture (MOR) of 12 mm thickness cement composites developed using 5% GRP waste fibre attained 16.5 N/mm². The findings of this work pave the way for further GRP waste recycling in precast construction products for use in various applications.     

Mitigation of greenhouse gas emissions by anaerobic digestion of cattle slurry

Biogas treatment of animal manures is an upcoming technology because it is a way of producing renewable energy (biogas). However, little is known about effects of this management strategy on greenhouse gas (GHG) emissions during fermentation, storage, and field application of the substrates compared to untreated slurries. In this study, we compared cattle slurry and cattle slurry with potato starch as additive during the process of fermentation, during storage and after field application. The addition of potato starch strongly enhanced CH₄ production from 4230 l CH₄ m⁻³ to 8625 l CH₄ m⁻³ in the fermenter at a hydraulic retention time (HRT) of 29 days. Extending the HRT to 56 days had only a small effect on the CH₄ production. Methane emissions from stored slurry depended on storage temperature and were highest from unfermented slurry followed by the slurry/starch mixture. Gas emissions from untreated and fermented slurry during storage were further analyzed in a pilot-scale experiment with different levels of covering such as straw cover, a wooden lid and no cover. Emissions of greenhouse gases (CH₄, N₂O, NH₃) were in the range of 14.3–17.1 kg CO₂ eq. m⁻³ during winter (100 day storage period) and 40.5–90.5 kg CO₂ eq. m⁻³ during summer (140 day storage period). A straw cover reduced NH₃ losses, but not overall GHG emissions, whereas a solid cover reduced CH₄ and NH₃ emissions. After field application, there were no significant differences between slurry types in GHG emissions (4.15–8.12 kg CO₂ eq. m⁻³ a⁻¹). GHG emissions from slurry stores were more important than emissions after field application. Co-digestion of slurry with additives such as starch has a large potential to substitute fossil energy by biogas. On a biogas plant, slurry stores should be covered gas-tight in order to eliminate GHG emissions and collect CH₄ for electricity production.     

Material flows in the life cycle of leather

This paper presents a study on the resource and environmental profile of leather for communicating to the consumers about the environmental burdens of leather products. The results indicate that significant environmental impacts were caused during the tanning and finishing of leather as well as the electricity production and transportation required in the life cycle. The use of fossil fuels in the production of energy has greater impact with increased emissions leading to about 15190 kg CO₂ equivalent of global warming and about 73 kg SO₂ equivalent of acidification while producing 100 m² of leather for shoe uppers. Further resource use of 174 kg of coal, 6.5 kg of fuel oil, 17.4 m³ of water and 348 kg of chemicals of which about 204 kg are hazardous are consumed, and wastewater of about 17 m³, BOD of 55 kg, COD of about 146 kg, TDS of 732 kg and solid waste of about 1445 kg are generated during the life cycle for the production of 100 m² of leather. The total solid waste generated is 1317 kg, out of which about 80% is biodegradable contributed by slaughtering, tanning and finishing stage, 14% is non-biodegradable contributed by tanning, finishing and electricity production stages and 6% is hazardous mainly from tanning and finishing stage of leather.     

Methane,nitrous oxide and ammonia emissions during storage and after application of dairy cattle slurry and influence of slurry treatment

Slurries are a significant source of CH₄, NH₃ and N₂O emissions to the atmosphere. The research project aimed at quantifying CH₄, NH₃ and N₂O emissions from liquid manure stores and after manure application under field conditions. The influence of the manure treatment options “no treatment”, “slurry separation”, “anaerobic digestion”, “slurry aeration” and “straw cover” on the emission level was investigated. Approximately 10 m³ of differently treated slurry were stored in pilot scale slurry tanks. Emissions were followed for c. 80 days. After the storage period, slurries were applied to permanent grassland. Greenhouse gas emissions from slurry were mainly caused by methane emissions during storage and by nitrous oxide emissions after field application of manures. Mitigation of GHG emissions can be achieved by a reduction in slurry dry matter and easily degradable organic matter content. Ammonia emissions mainly occurred after field application. Untreated slurry emitted 226.8 g NH₃ m⁻³ and 92.4 kg CO₂ eq. m⁻³ (storage and field application). Slurry separation (liquid fraction and composting of the solid fraction) resulted in NH₃ losses of 402.9 g m⁻³ and GHG losses of 58.5 kg CO₂ eq. m⁻³. Anaerobic digestion was a very effective means to reduce GHG emissions. 37.9 kg CO₂ eq. m⁻³ were lost. NH₃ emissions were similar to those from untreated slurry. Covering the slurry store with a layer of chopped straw instead of a wooden cover increased NH₃ emissions to 320.4 g m⁻³ and GHG emissions to 119.7 kg CO₂ eq. m⁻³. Slurry aeration nearly doubled NH₃ emissions compared to untreated slurry. GHG emissions were reduced to 53.3 kg CO₂ eq. m⁻³.     

Copper and zinc recycling in Australia: potential quantities and policy options

This paper presents relevant data for industry and governmental policy makers with the aim of increasing the recycling rate of end-of-life copper and zinc in Australia in a technically and economically feasible way. The methodology used to quantify and spatially distribute end-of-life flows of copper and zinc is based on existing and anticipated in-use stocks, their residence times, and their historical and anticipated future evolution. Australia currently (ca. 2000) generates about 72 Gg/year and 57 Gg/year of end-of-life copper and zinc, respectively. Some 70% of all discarded copper and 40% of all discarded zinc generated in Australia are currently being recycled. A detailed assessment shows that about 75% of all end-of-life material in Australia comes from the three states New South Wales, Victoria, and Queensland. In Australia, about 70–75% of waste copper and waste zinc is generated in urban areas. Residential applications account for about 40% (copper) and 60% (zinc) of the generated discards; commercial and industrial applications account for the remainder. By 2030, the discard flows are predicted to increase by about 105% and 155%, to 150 Gg Cu/year and 145 Gg Zn/year, providing substantially increased opportunities for recovery and re-use. Priority targets for the improvement of copper and zinc recycling in Australia are buildings under renovation, urban infrastructure, the transportation sector, and also consumer and business durables. Urban centres are particularly attractive locations for recycling facilities, especially in Perth and Adelaide.     

The study of ultrasound-assisted oxidative desulfurization process applied to the utilization of pyrolysis oil from waste tires

In recent years, the increasing world population and rapid industrial development has increased the consumption of fossil fuel-derived oils. In response to the resulting exhaustion of fossil fuel energy, many countries around the world are investigating methods of waste energy recovery and reuse, including oil recovery from the pyrolysis process of waste tires. This study investigates the efficiency of an ultrasound-assisted oxidative desulfurization (UAOD) process in sulfur reduction from diesel oil and the pyrolysis oil from waste tires treatment. The results indicate that the oxidation efficiency increases as the doses of transition metal catalyst are increased. Longer sonication time also enhances the oxidation process, apparently through the biphasic transfer of oxidants, which results in a high yield of organic sulfur oxidation products. The best desulfurization efficiency was 99.7% (2.67 ppm sulfur remaining) and 89% (800 ppm sulfur remaining) for diesel and pyrolysis oils, respectively, via a process executed by two UAOD units connected in series and combined with solid adsorption using 30 g of Al₂O₃ in 6 cm columns. These batch experiment results demonstrate clean waste energy recovery and utilization, while fulfilling the requirements of Taiwan EPA environmental regulations (sulfur concentrations less than 5000 ppm).     

Integrated environmental assessment of biodiesel production from soybean in Brazil

This paper presents the results of an environmental impact assessment of biodiesel production from soybean in Brazil. In order to achieve this objective, environmental impact indicators provided by Emergy Accounting (EA), Embodied Energy Analysis (EEA) and Material Flow Accounting (MFA) were used. The results showed that for one liter of biodiesel 8.8 kg of topsoil are lost in erosion, besides the cost of 0.2 kg of fertilizers, about 5.2 m² of crop area, 7.33 kg of abiotic materials, 9.0 tons of water and 0.66 kg of air and about 0.86 kg of CO₂ were released. About 0.27 kg of crude oil equivalent is required as inputs to produce one liter of biodiesel, which means an energy return of 2.48 J of biodiesel per Joule of fossil fuel invested. The transformity of biodiesel (3.90E + 05 seJ J^?1) is higher than those calculated for fossil fuels as other biofuels, indicating a higher demand for direct and indirect environmental support. Similarly, the biodiesel emergy yield ratio (1.62) indicates that a very low net emergy is delivered to consumers, compared to alternatives. Obtained results show that when crop production and industrial conversion to fuel are supported by fossil fuels in the form of chemicals, goods, and process energy, the fraction of fuel that can actually be considered renewable is very low (around 31%).     

Sustainability assessment of large-scale ethanol production from sugarcane

The present study assesses the sustainability of ethanol produced from sugarcane and examines the environmental feasibility of a large-scale production through the use of: fossil fuel embodied energy and Emergy Assessment including farm and industrial production phases. The study indicates that about 1.82 kg of topsoil eroded, 18.4 l of water and 1.52 m² of land are needed to produce 1 l of ethanol from sugarcane. Also, 0.28 kg of CO₂ is released per liter of ethanol produced. The energy content of ethanol is 8.2 times greater than the fossil-based energy required to produce it. The transformity of ethanol is about the same as those calculated for fossil fuels. The Renewability of ethanol is 30%, a very low value; other emergy indices indicate important environmental impacts as well as natural resources consumption. The results obtained indicate that sugarcane and ethanol production present low renewability when a large-scale system is adopted.     

Greenhouse gas emissions from production and use of used cooking oil methyl ester as transport fuel in Thailand

Biodiesel, produced from various vegetable and/or animal oils, is one of the most promising alternative fuels for transportation in Thailand. Currently, the waste oils after use in cooking are not disposed adequately. Such oils could serve as a feedstock for biodiesel which would also address the waste disposal issue. This study compares the life cycle greenhouse gas (GHG) emissions from used cooking oil methyl ester (UCOME) and conventional diesel used in transport. The functional unit (FU) is 100 km transportation by light duty diesel vehicle (LDDV) under identical driving conditions. Life cycle GHG emissions from conventional diesel are about 32.57 kg CO₂-eq/FU whereas those from UCOME are 2.35 kg CO₂-eq/FU. The GHG emissions from the life cycle of UCOME are 93% less than those of conventional diesel production and use. Hence, a fuel switch from conventional diesel to UCOME will contribute greatly to a reduction in global warming potential. This will also support the Thai Government's policy to promote the use of indigenous and renewable sources for transportation fuels.     

Balancing of greenhouse gas emissions and economic efficiency for biogas-production through anaerobic co-fermentation of slurry with organic waste

Using the organic fraction of municipal solid waste (OFMSW) for biogas production might contribute to greenhouse gas mitigation, but emissions linked with biogas production can reduce these beneficial effects. Therefore the emissions of NH₃, CH₄ and N₂O and costs caused by treating OFMSW by co-fermentation with slurry were calculated in detail from literature data, and strategies for reducing emissions were evaluated. Emission factors were calculated for single gases during storage and after application. The sensitivity of the calculations concerning the organic dry matter content of OFMSW, retention time and CH₄-yield was analyzed. The anaerobic co-fermentation of OFMSW increased biogas yields and contributed to the reduction of CO₂ emissions with 32 to 152 kg CO₂ t⁻¹ organic waste depending on application and storage techniques used for the fermentation residues. Considering a payment of 0.1 €/kWh for the electricity produced, the costs for utilization of OFMSW in slurry based biogas plants were calculated to range between 34 and 38 € t⁻¹. Measures for mitigating greenhouse gas emissions by covering the fermentation residue stores proved to be more cost effective with 3–31 € t⁻¹ CO₂ compared to immediate harrowing or injecting the residues during field application.     

Life cycle greenhouse gases,energy and cost assessment of automobiles using magnesium from Chinese Pidgeon process

Magnesium (Mg) has a great potential to reduce vehicle weight, fuel consumption, and greenhouse gas emissions. The Chinese Mg industry has developed rapidly since the 1990s. The output of Mg reached 700,000 tons in 2006, accounting for more than 70% of global Mg production. Most of Mg is produced in China through the Pidgeon process that has an intensive energy usage and generates a large amount of greenhouse gas (GHG) emissions, which may offset the potential advantage of using Mg parts in automobiles. It is critical to quantify the energy usage and GHG emissions through entire life cycle when the Mg are applied to automobiles. It is also essential to evaluate cost implications of the Mg parts application in automobiles and ensure it to be cost competitive. The objectives of this study are (1) Build a life cycle inventory (LCI) of Mg produced by Pidgeon process; (2) Establish an LCA model that can evaluate GHG emissions and energy usage for the Mg automotive application; (3) Estimate the cost implications of the Mg parts application in automobiles.An Mg LCI was built based on interviews and surveys and the GREET model was adapt for this study. The results indicated that, for each kilogram of Mg produced by Pidgeon process, GHG emissions and energy usage would be 27 kg CO₂eq and 280 MJ, which are five times higher than steel production. Replacing steel with 82 kg Mg on a base automobile would lower curb weight by 5.7%, but only reduce life cycle GHG emissions and energy usage by 0.8% and 1.3%. Scenario analyses indicated that potential reduction of life cycle GHG emissions and energy usage could reach to 15%, if secondary weight saving and a smaller engine were included. Cost analyses also show 18% reduction when the additional weight saving and a smaller displacement engine were included, under a 100,000 km driving distance and gasoline price at $1.0/l.     

Comparing intensive,extensified and organic grassland farming in southern Germany by process life cycle assessment

To reduce the environmental burden of agriculture, suitable methods to comprehend and assess the impact on natural resources are needed. One of the methods considered is the life cycle assessment (LCA) method, which was used to assess the environmental impacts of 18 grassland farms in three different farming intensities — intensive, extensified, and organic — in the Allgäu region in southern Germany. Extensified and organic compared with intensive farms could reduce negative effects in the abiotic impact categories of energy use, global warming potential (GWP) and ground water mainly by renouncing mineral nitrogen fertilizer. Energy consumption of intensive farms was 19.1 GJ ha⁻¹ and 2.7 GJ t⁻¹ milk, of extensified and organic farms 8.7 and 5.9 GJ ha⁻¹ along with 1.3 and 1.2 GJ t⁻¹ milk, respectively. Global warming potential was 9.4, 7.0 and 6.3 CO₂-equivalents ha⁻¹ and 1.3, 1.0 and 1.3 CO₂-equivalents t⁻¹ milk for the intensive, extensified and organic farms, respectively. Acidification calculated in SO₂-equivalents was high, but the extensified (119 kg SO₂ ha⁻¹) and the organic farms (107 kg SO₂ ha⁻¹) emit a lower amount compared with the intensive farms (136 kg SO₂ ha⁻¹). Eutrophication potential computed in PO₄-equivalents was higher for intensive (54.2 kg PO₄ ha⁻¹) compared with extensified (31.2 kg PO₄ ha⁻¹) and organic farms (13.5 kg PO₄ ha⁻¹). Farmgate balances for N (80.1, 31.4 and 31.1 kg ha⁻¹) and P (5.3, 4.5 and −2.3 kg ha⁻¹) for intensive, extensified and organic farms, respectively, indicate the different impacts on ground and surface water quality. Analysing the impact categories biodiversity, landscape image and animal husbandry, organic farms had clear advantages in the indicators number of grassland species, grazing cattle, layout of farmstead and herd management, but indices in these categories showed a wide range and are partly independent of the farming system.     

Energy based phenomenological model for optimizing the sheared edge in the trimming of steels

Attributes related to the dimensional quality of hot rolled steels are very important in commercial sectors that make direct use of this product, because delay or equipment damage can be avoided when forming in downstream operations. In this research, the steel sheet edge trimming process and its relationship with the defect known as broken edge is experimental and numerically studied. The type of material, horizontal clearance between knives and the energy spent during the cutting process are analyzed in detail. A metal-mechanical study is carried out for obtaining a microstructural hardness and flow stress characterization. Consequently, the edge trimming process is FEM simulated and its results in relation to knife penetration and shear stress lead to determining the energy spent during the cutting process. A mathematical model is determined under the consideration that minimum energy gives the optimum cutting conditions. The model proposes a reliable value for the horizontal clearance (H_c), between knives, taking as the principal factors: energy consumed during the edge trimming process, sheet thickness (T_h), carbon content (C) and/or its ultimate tensile strength, expressed as: H_c = α + βT_h − γC. A comparison of the recommended numerical results with the best practical conditions is carried out and a high coincidence is successfully found. This model is expected to be easily adopted as a tool where operators can adjust and control the parameters of process, and then, as a result, produce a sheet without edge trimming defects as well as a reduction in efficiency costs.     

Nitrous oxide emissions from organic and conventional crop rotations in five European countries

Nitrous oxide (N₂O) emissions from agriculture are currently estimated from N inputs using emission factors, and little is known about the importance of regional or management-related differences. This paper summarizes the results of a study in which N₂O emission rates were recorded on 15–26 occasions during a 12-month period in organic and conventional dairy crop rotations in five European countries (Austria, Denmark, Finland, Italy, UK). A common methodology based on static chambers was used for N₂O flux measurements, and N₂O data were compiled together with information about N inputs (from fertilizers, N₂ fixation, atmospheric deposition and excretal returns), crop rotations and soil properties. Organic rotations received only manure as N fertilizer, while manure accounted for 0–100% of fertilizer N in conventional rotations. A linear regression model was used to examine effects of location, system and crop category on N₂O emissions, while a second model examined effects of soil properties. Nitrous oxide emissions were higher from conventional than from organic crop rotations except in Austria and, according to the statistical analysis, the differences between locations and crop categories were significant. Ammonium was significantly related to N₂O emissions, although this effect was dominated by observations from a grazing system. Despite the limited number of samplings, annual emissions were estimated by interpolation. Across the two systems and five locations there was a significant relationship between total N inputs and N₂O emissions at the crop rotation level which indicated that annually 1.6 ± 0.2% (mean ± standard error) of total N inputs were lost as N₂O, while there was a background emission of 1.4 ± 0.3 kg N₂O-N ha⁻¹ year⁻¹. Although this measurement program emphasized system effects at the expense of high temporal resolution, the results indicate that N input is a significant determinant for N₂O emissions from agricultural soils.     

Biogas production from maize and dairy cattle manure—Influence of biomass composition on the methane yield

There is an increasing world wide demand for energy crops and animal manures for biogas production. To meet these demands, this research project aimed at optimising anaerobic digestion of maize and dairy cattle manures. Methane production was measured for 60 days in 1 l eudiometer batch digesters at 38 °C. Manure received from dairy cows with medium milk yield that were fed a well balanced diet produced the highest specific methane yield of 166.3 Nl CH₄ kg VS⁻¹. Thirteen early to late ripening maize varieties were grown on several locations in Austria. Late ripening varieties produced more biomass than medium or early ripening varieties. On fertile locations in Austria more than 30 Mg VS ha⁻¹ can be produced. The methane yield declined as the crop approaches full ripeness. With late ripening maize varieties, yields ranged between 312 and 365 Nl CH₄ kg VS⁻¹ (milk ripeness) and 268–286 Nl CH₄ kg VS⁻¹ (full ripeness). Silaging increased the methane yield by about 25% compared to green, non-conserved maize. Maize (Zea mays L.) is optimally harvested, when the product from specific methane yield and VS yield per hectare reaches a maximum. With early to medium ripening varieties (FAO 240–390), the optimum harvesting time is at the “end of wax ripeness”. Late ripening varieties (FAO ca. 600) may be harvested later, towards “full ripeness”. Maximum methane yield per hectare from late ripening maize varieties ranged between 7100 and 9000 Nm³ CH₄ ha⁻¹. Early and medium ripening varieties yielded 5300–8500 Nm³ CH₄ ha⁻¹ when grown in favourable regions. The highest methane yield per hectare was achieved from digestion of whole maize crops. Digestion of corns only or of corn cob mix resulted in a reduction in methane yield per hectare of 70 and 43%, respectively. From the digestion experiments a multiple linear regression equation, the Methane Energy Value Model, was derived that estimates methane production from the composition of maize. It is a helpful tool to optimise biogas production from energy crops. The Methane Energy Value Model requires further validation and refinement.     

CaCO3 production using liquid waste from Solvay method

Process of obtaining CaCO₃ from the waste post-distillation liquid DS and post-filtration liquid from Solvay method of the soda production at 303 K was investigated. Reagents were dosed in a stoichiometric ratio without dilution, for different concentrations of the DS and post-filtration liquids. The dosage time was varied in the range 2–30 min, the reagent stirring rate was 500 rpm. For the obtained samples of CaCO₃, the bulk and packing densities, water, paraffin oil and dibutyl phthalate absorption capacities, distribution of the particle size as well as the crystalline form were determined.     

Modeling increased demand of energy for air conditioners and consequent CO2 emissions to minimize health risks due to climate change in India

Developing countries situated mostly in latitudes that are projected for the highest climate change impact in the twenty-first century will also have a predictable increase in demand on energy sources. India presents us with a unique opportunity to study this phenomenon in a large developing country. This study finds that climate adaptation policies of India should consider the significance of air conditioners (A/Cs) in mitigation of human vulnerability due to unpredictable weather events such as heat waves. However, the energy demand due to air conditioning usage alone will be in the range of an extra ～750,000 GWh to ～1,350,000 GWh with a 3.7 °C increase in surface temperatures under different population scenarios and increasing incomes by the year 2100. We project that residential A/C usage by 2100 will result in CO₂ emissions of 592 Tg to 1064 Tg. This is significant given that India's total contribution to global CO₂ emissions in 2009 was measured at 1670 Tg and country's residential and commercial electricity consumption in 2007 was estimated at 145,000 GWh.