Simultaneous removal of Congo red and cadmium(II) from aqueous solutions using graphene oxide–silica composite as a multifunctional adsorbent

Graphene oxide is a very high capacity adsorbent due to its functional groups and π?π interactions with other compounds. Adsorption capacity of graphene oxide, however, can be further enhanced by having synergistic effects through the use of mixed-matrix composite. In this study, silica-decorated graphene oxide (SGO) was used as a high-efficiency adsorbent to remove Congo red (CR) and Cadmium (II) from aqueous solutions. The effects of solution initial concentration (20 to 120 mg/l), solution pH (pH 2 to 7), adsorption duration (0 to 140 min) and temperature (298 to 323 K) were measured in order to optimize the adsorption conditions using the SGO adsorbent. Morphological analysis indicated that the silica nanoparticles could be dispersed uniformly on the graphene oxide surfaces. The maximum capacities of adsorbent for effective removal of Cd (II) and CR were 43.45 and 333.33 mg/g based on Freundlich and Langmuir isotherms, respectively. Langmuir and Freundlich isotherms displayed the highest values of Q_max for CR and Cd (II) adsorption in this study, which indicated monolayer adsorption of CR and multilayer adsorption of Cd (II) onto the SGO, respectively. Thermodynamic study showed that the enthalpy (ΔH) and Gibbs free energy(ΔG) values of the adsorption process for both pollutants were negative, suggesting that the process was spontaneous and exothermic in nature. This study showed active sites of SGO (π-π, hydroxyl, carboxyl, ketone, silane-based functional groups) contributed to an enormous enhancement in simultaneous removal of CR and Cd (II) from an aqueous solution, Therefore, SGO can be considered as a promising adsorbent for future water pollution control and removal of hazardous materials from aqueous solutions.     

Effects of the surface chemistry of macroreticular adsorbents on the adsorption of 1-naphthol/1-naphthylamine mixtures from water

The adsorption behaviors of 1-naphthol, 1-naphthylamine and l-naphthol/l-naphthylamine mixtures in water over two macroreticular adsorbents were investigated in single or binary batch systems at 293 K, 303 K and 313 K respectively. All the adsorption isotherms in the studied systems can be adequately fitted by Langmuir model. In the case of aminated macroreticular adsorbent NDA103, 1-naphthol is adsorbed to a larger extent than 1-naphthylamine; while, the opposite trend is found for nonpolar macroreticular adsorbent NDA100. It is noteworthy that at higher temperature（303 K and 313 K）, the total uptake amounts of 1-naphthol and 1-naphthylamine in all binary-component systems are obvious larger than the pure uptake amounts in single-component systems, which is presumably due to the cooperative effect primarily arisen from the hydrogen-bonding interaction between the loaded 1-naphthol and 1-naphthylamine molecules. The simultaneous adsorption systems were confirmed to be helpful to the selective adsorption towards 1-naphthol according to the larger selective index.     

Adsorption thermodynamics and kinetic investigation of aromatic amphoteric compounds onto different polymeric adsorbents

The adsorption behavior of p-aminobenzoic acid and o-aminobenzoic acid onto the different polymeric adsorbents was systematically investigated as a function of the solution concentration and temperature.Experimental results indicated that the equilibrium adsorption data of the four polymeric adsorbents fitted well in the Freundlich isotherm.The adsorption capacity of multi-functional polymeric adsorbent NJ-99 was the highest,which might be attributed to the strong hydrogen-bonding interaction between the amino groups on the resin and the carboxyl group of aminobenzoic acid.The adsorption capacity of o-aminobenzoic acid onto any adsorbent was higher than p-aminobenzoic acid.Thermodynamic studies suggested the exothermic,spontaneous physical adsorption process.Adsorption kinetics results showed that the adsorption followed the pseudo-second-order kinetics model and the intraparticle mass transfer process was the rate-controlling step.     

Removal of phosphate by Fe-coordinated amino-functionalized 3D mesoporous silicates hybrid materials

Phosphate removal from aqueous waste streams is an important approach to control the eutrophication downstream bodies of water. A Fe(III) coordinated amino-functionalized silicate adsorbent for phosphate adsorption was synthesized by a post-grafting and metal cation incorporation process. The surface structure of the adsorbent was characterized by X-ray di raction, N2 adsoropion/desoprotion technique, and Fourier transform infrared spectroscopy. The experimental results showed that the adsorption equilibrium data were well fitted to the Langmuir equation. The maximum adsorption capacity of the modified silicate material was 51.8 mg/g. The kinetic data from the adsorption of phosphate were fitted to pseudo second-order model. The phosphate adsorption was highly pH dependent and the relatively high removal of phosphate fell within the pH range 3.0–6.0. The coexistence of other anions in solutions has an adverse e ect on phosphate adsorption; a decrease in adsorption capacity followed the order of exogenous anions: F?? > SO2?? 4 > NO??3 > Cl??. In addition, the adsorbed phosphate could be desorbed by NaOH solutions. This silicate adsorbent with a large adsorption capacity and relatively high selectivity could be utilized for the removal of phosphate from aqueous waste streams or in aquatic environment.     

Kinetics and thermodynamic studies of Methyl Orange removal by polyvinylidene fluoride-PEDOT mats

We report the preparation of poly(3,4-ethylene dioxythiophene) (PEDOT)-modified polyvinylidene fluoride electrospun fibers and their use as a novel adsorbent material for the removal of the anionic dye Methyl Orange (MO) from aqueous media. This novel adsorbent material can be used to selectively remove MO on a wide pH range (3.0–10.0), with a maximum capacity of 143.8 mg/g at pH 3.0. When used in a recirculating filtration system, the maximum absorption capacity was reached in a shorter time (20 min) than that observed for batch mode experiments (360 min). Based on the analyses of the kinetics and adsorption isotherm data, one can conclude that the predominant mechanism of interaction between the membrane and the dissolved dye molecules is electrostatic. Besides, considering the estimated values for the Gibbs energy, and entropy and enthalpy changes, it was established that the adsorption process is spontaneous and occurs in an endothermic manner. The good mechanical and environmental stability of these membranes allowed their use in at least 20 consecutive adsorption/desorption cycles, without significant loss of their characteristics. We suggest that the physical-chemical characteristics of PEDOT make these hybrid mats a promising adsorbent material for use in water remediation protocols and effluent treatment systems.     

Adsorption of catechol from aqueous solution by aminated hypercrosslinked polymers

Adsorption of catechol from aqueous solution with the hypercrosslinked polymeric adsorbent NDA-100 and its derivatives AH-1,AH-2 and AH-3 aminated by dimethylamine, the commercial resin Amberlite XAD-4 and weakly basic anion exchanger resin D301 was compared. It was found that the aminated hypercrosslinked resins had the highest adsorption capacities among the tested polymers. The empirical Freundlich equation was successfully employed to describe the adsorption process. Specific surface area and micropore structure of the adsorbent, in company with tertiary amino groups on matrix affected the adsorption performance towards catechol. In addition, thermodynamic study was carried out to interpret the adsorption mechanism. Kinetic study testified that the tertiary amino groups on the polymer matrix could decrease the adsorption rate and increase the adsorption apparent activation energy.     

Ion adsorption components in liquid/solid systems

Experiments on Zn^2＋ and Cd^2＋ adsorptions on vermiculite in aqueous solutions were conducted to investigate the widely observed adsorbent concentration effect on the traditionally defined adsorption isotherm in the adsorbate range 25--500 mg/L and adsorbent range 10--150 g/L. The results showed that the equilibrium ion adsorption density did not correspond to a unique equilibrium ion concentration in liquid phase. Three adsorbate/adsorbent ratios, the equilibrium adsorption density, the ratio of equilibrium adsorbate concentration in liquid phase to adsorbent concentration, and the ratio of initial adsorbate concentration to adsorbent concentration, were found to be related with unique values in the tested range. Based on the assumption that the equilibrium state of a liquid/solid adsorption system is determined by four mutually related components： adsorbate in liquid phase, adsorbate in solid phase, uncovered adsorption site and covered adsorption site, and that the equilibrium chemical potentials of these components should be equalized, a new model was presented for describing ion adsorption isotherm in liquid/solid systems. The proposed model fit well the experimental data obtained from the examined samples.     

Ciprofloxacin adsorption from aqueous solution onto chemically prepared carbon from date palm leaflets

A chemically prepared carbon was synthesized from date palm leaflets via sulphuric acid carbonization at 160℃. Adsorption of ciprofloxacin (CIP) from aqueous solution was investigated in terms of time, pH, concentration, temperature and adsorbent status (wet and dry). The equilibrium time was found to be 48 hr. The adsorption rate was enhanced by raising the temperature for both adsorbents, with adsorption data fitting a pseudo second-order model well. The activation energy, E_a, was found to be 17 kJ/mol, indicating a diffusion-controlled, physical adsorption process. The maximum adsorption was found at initial pH 6. The wet adsorbent showed faster removal with higher uptake than the dry adsorbent, with increased performance as temperature increased (25-45℃). The equilibrium data were found to fit the Langmuir model better than the Freundlich model. The thermodynamic parameters showed that the adsorption process is spontaneous and endothermic. The adsorption mechanism is mainly related to cation exchange and hydrogen bonding.     

Adsorption behavior of benzenesulfonic acid by novel weakly basic anion exchange resins

Two novel weakly basic anion exchange resins(SZ-1 and SZ-2) were prepared via the reaction of macroporous chloromethylated polystyrene-divinylbenzene(Cl-PS-DVB) beads with dicyclohexylamine and piperidine, respectively. The physicochemical structures of the resulting resins were characterized using Fourier Transform Infrared Spectroscopy and pore size distribution analysis. The adsorption behavior of SZ-1 and SZ-2 for benzenesulfonic acid(BA) was evaluated, and the common commercial weakly basic anion exchanger D301 was also employed for comparison purpose. Adsorption isotherms and influence of solution p H, temperature and coexisting competitive inorganic salts(Na2SO4and Na Cl) on adsorption behavior were investigated and the optimum desorption agent was obtained.Adsorption isotherms of BA were found to be well represented by the Langmuir model.Thermodynamic parameters involving ΔH, ΔG and ΔS were also calculated and the results indicate that adsorption is an exothermic and spontaneous process. Enhanced selectivity of BA sorption over sulfate on the two novel resins was observed by comparison with the commercial anion exchanger D301. The fact that the tested resins loaded with BA can be efficiently regenerated by Na Cl solution indicates the reversible sorption process. From a mechanistic viewpoint, this observation clearly suggests that electrostatic interaction is the predominant adsorption mechanism. Furthermore, results of column tests show that SZ-1possesses a better adsorption property than D301, which reinforces the feasibility of SZ-1for potential industrial application.     

Synthesis of mesoporous Cu/Mg/Fe layered double hydroxide and its adsorption performance for arsenate in aqueous solutions

The mesoporous Cu/Mg/Fe layered double hydroxide(Cu/Mg/Fe-LDH) with carbonate intercalation was synthesized and used for the removal of arsenate from aqueous solutions.The Cu/Mg/Fe-LDH was characterized by Fourier transform infrared spectrometry,X-ray diffraction crystallography,scanning electron microscopy,X-ray photoelectron spectroscopy and Brunauer-Emmett-Teller.Effects of various physico-chemical parameters such as pH,adsorbent dosage,contact time and initial arsenate concentration on the adsorption of arsenate onto Cu/Mg/Fe-LDH were investigated.Results showed that it was efficient for the removal of arsenate,and the removal efficiency of arsenate increased with the increment of the adsorbent dosage,while the arsenate adsorption capacity decreased with increase of initial pH from 3 to 11.The adsorption isotherms can be well described by the Langmuir model with R 2 > 0.99.Its adsorption kinetics followed the pseudo second-order kinetic model.Coexisting ions such as HPO42-,CO32-,SO42and NO3could compete with arsenate for adsorption sites on the Cu/Mg/Fe-LDH.The adsorption of arsenate on the adsorbent can be mainly attributed to the ion exchange process.It was found that the synthesized Cu/Mg/Fe-LDH can reduce the arsenate concentration down to a final level of < 10 μg/L under the experimental conditions,and makes it a potential material for the decontamination of arsenate polluted water.     

NaOH改性桤木锯末对废水中Cd2+,Pb2+的吸附

文章研究了NaOH改性桤木锯末对水中Cd2+和Pb3+的吸附特性,探讨了pH值、锯末用量、吸附时间对吸附昔的影响及其吸附动力学和吸附柱动力学.结果表明:(1)锯末吸附Cd2+和Pb2+的最佳pH值分别为1.0和5.0(2)随锯末用量增加,锯末对Cd2+和Pb2+的吸附量减少,吸附率增加,对Cd2+和Pb2+吸附率分别可...     

累托石/腐殖酸微球对水中Cd~(2+)的吸附及动力学研究

采用累托石、腐殖酸、海藻酸钠、氯化钙和聚乙烯醇等材料制备微球状吸附剂去除水中镉离子。考察了微球用量、吸附时间、pH值等因素对吸附效果的影响,测定了吸附等温线,对吸附动力规律进行了探讨。结果表明,在本研究条件下,微球用量、温度和吸附时间对水中镉离子的吸附效果有显著性影响,但溶液pH值对吸附效果的影响并不显著。最优吸附条件为:温度25℃、溶液pH为6,吸附时间6h、微球用量为0.025g/mL。等温吸附规律可用Freundlich和Langmuir模式较好地模拟,吸附呈单分子层形式,吸附性能良好,吸附易于进行。吸附动力学规律遵循Lagergren准一级和Elovich动力学模型。     

两种ZSM-5沸石分子筛吸附水中氨氮的研究

考察了两种硅铝比分别为25及50的ZSM-5沸石分子筛对水中氨氮的吸附性能及影响因素.研究表明,25℃时,25H及50H型沸石的吸附平衡时间分别为10 min和35 min,吸附等温线均符合Langmuir经验模型,25 H型分子筛的饱和吸附容量较大,为7.83 mg/g,50H型分子筛为4.36 mg/g.当吸附剂投...     

Removal of ammonium ion from water by Na-rich birnessite: Performance and mechanisms

Na-rich birnessite (NRB) was synthesized by a simple synthesis method and used as a high-efficiency adsorbent for the removal of ammonium ion (NH₄⁺) from aqueous solution. In order to demonstrate the adsorption performance of the synthesized material, the effects of contact time, pH, initial ammonium ion concentration, and temperature were investigated. Adsorption kinetics showed that the adsorption behavior followed the pseudo second-order kinetic model. The equilibrium adsorption data were fitted to Langmuir and Freundlich adsorption models and the model parameters were evaluated. The monolayer adsorption capacity of the adsorbent, as obtained from the Langmuir isotherm, was 22.61 mg NH₄⁺-N/g at 283 K. Thermodynamic analyses showed that the adsorption was spontaneous and that it was also a physisorption process. Our data revealed that the higher NH₄⁺ adsorption capacity could be primarily attributed to the water absorption process and electrostatic interaction. Particularly, the high surface hydroxyl-content of NRB enables strong interactions with ammonium ion. The results obtained in this study illustrate that the NRB is expected to be an effective and economically viable adsorbent for ammonium ion removal from aqueous system.     

Adsorption of humic acid from aqueous solution on bilayer hexadecyltrimethyl ammonium bromide-modified zeolite

Surfactant-modified natural zeolites (SMNZ) with different coverage types were prepared by loading hexadecyltrimethyl ammonium bromide (HTAB) onto the surface of a natural zeolite. The adsorption behavior of humic acid (HA) on SMNZ was investigated. Results indicate that the adsorbent SMNZ exhibited a higher affinity toward HA than the natural zeolite. HA removal efficiency by SMNZ increased with HTAB loading. Coexisting Ca²⁺ in solution favored HA adsorption onto SMNZ. Adsorption capacity decreased with an increasing solution pH. For typical SMNZ with bilayer HTAB coverage, HA adsorption process is well described by a pseudo-second-order kinetic model. The experimental isotherm data fitted well with the Langmuir model. Calculated maximum HA adsorption capacities for SMNZ with bilayer HTAB coverage at pH 5.5 and 7.5 were 63 and 41 mg·g⁻¹, respectively. E2/E3 (absorbance at 250 nm to that at 365 nm) and E4/E6 (absorbance at 465 nm to that at 665 nm) ratios of the residual HA in solution were lower than that of the original HA solution. This indicates that the HA fractions with high polar functional groups, low molecular weight (MW), and aromaticity had a stronger tendency for adsorption onto SMNZ with bilayer HTAB coverage. Results show that HTAB-modified natural zeolite is a promising adsorbent for removal of HA from aqueous solution.     

磷酸法活化银杏叶活性炭对DBP的吸附性能研究

以银杏树叶为原料,使用磷酸活化法制备粉末活性炭,采用银杏叶粉末活性炭作为吸附剂,研究了其对DBP的吸附性能。研究考察了温度、吸附时间、pH对DBP吸附性能的影响,同时拟合了吸附等温线,探讨了热力学和动力学性质。结果表明温度、吸附时间、pH对吸附效果均有影响,吸附过程符合Langmuir吸附等温方程,吸附过程是自发的,二级动力学方程更好地描述吸附动力学规律。     

2,4-二硝基酚在离子交换树脂上吸附与微波脱附

研究了717强碱阴离子交换树脂对水中2,4-二硝基苯酚(2,4-DNP)的吸附解吸性能,探讨了吸附的热力学和动力学特性及其微波脱附性能。结果表明:在pH=4～11时,该树脂对2,4-DNP有较强的吸附能力。Freundlich吸附等温方程能很好地描述吸附平衡数据,吸附过程为放热、熵减的自发过程。吸附动力学符合Lagergren二级速率方程,颗粒内扩散是吸附速率的主要控制步骤,可采用HSDM模型描述。以1mol/L HNO3+C2H5OH溶液作为脱附剂,采用微波辅助脱附再生,微波辐照累计5min时,酚脱附率可达90%以上。