Investigation of carbonyl compound sources at a rural site in the Yangtze River Delta region of China

Carbonyl compounds are important intermediates in atmospheric photochemistry, but their primary sources are still not understood well. In this work, carbonyls, hydrocarbons,and alkyl nitrates were continuously measured during November 2011 at a rural site in the Yangtze River Delta region of China. Mixing ratios of carbonyls and hydrocarbons showed large fluctuations during the entire measurement. The average level for total measured volatile organic compounds during the pollution episode from 25 th to 27 th November, 2011 was 91.6 ppb, about 7 times the value for the clean period of 7th–8th, November, 2011. To preliminarily identify toluene sources at this site, the emission ratio of toluene to benzene(T/B) during the pollution episode was determined based on photochemical ages derived from the relationship of alkyl nitrates to their parent alkanes. The calculated T/B was5.8 ppb/ppb, significantly higher than the values of 0.2–1.7 ppb/ppb for vehicular exhaust and other combustion sources, indicating the dominant influence of industrial emissions on ambient toluene. The contributions of industrial sources to ambient carbonyls were then calculated using a multiple linear regression fit model that used toluene and alkyl nitrates as respective tracers for industrial emission and secondary production. During the pollution episode, 18.5%, 69.0%, and 52.9% of measured formaldehyde, acetaldehyde, and acetone were considered to be attributable to industrial emissions. The emission ratios relative to toluene for formaldehyde, acetaldehyde, and acetone were determined to be 0.10, 0.20 and0.40 ppb/ppb, respectively. More research on industrial carbonyl emission characteristics is needed to understand carbonyl sources better.     

BTEX pollution caused by motorcycles in the megacity of HoChiMinh

Monitoring of benzene, toluene and xylenes (BTEX) was conducted along with traffic counts at 17 roadside sites in urban areas of HoChiMinh. Toluene was the most abundant substance, followed by p,m-xylenes, benzene, o-xylene and ethylbenzene. The maximum observed hour-average benzene concentration was 254 μg/m3 . Motorcycles contributed to 91% of the traffic fleet. High correlations among BTEX species, between BTEX concentrations and the volume of on-road motorcycles, and between inter-species ratios in air and in gasoline indicate the motorcycle-exhaust origin of BTEX species. Daily concentrations of benzene, toluene, ethylbenzene, p,m-xylenes and o-xylene were 56, 121, 21, 64 and 23 μg/m 3 , respectively. p,m-xylenes possess the highest ozone formation potential among the BTEX family.     

Levels, sources and health risks of carbonyls and BTEX in the ambient air of Beijing, China

The atmospheric concentrations of carbonyls and BTEX (benzene, toluene, ethylbenzene, m,p-xylene and o-xylene) were measured simultaneously at a same sampling site in Beijing from September 2008 to August 2010. The average concentrations of the total measured carbonyls during autumn, winter, spring, and summer were 37.7, 31.3, 39.7, 50.5 μg/m³, respectively, and maximal values for their diurnal variations usually happened at noontime. In contrast to carbonyls, the average concentrations of the total measured BTEX during the four seasons were 27.2, 31.9, 23.2, 19.1 μg/m³, respectively, and minimal values for their diurnal variations always occurred in the early afternoon. The average concentration for carbonyls increased about 24% from September 2008-August 2009 to September 2009-August 2010, for BTEX, increased about 15%. Integrated life time cancer risks for three carcinogens (benzene, formaldehyde and acetaldehyde) in Beijing exceeded the value of 1E-06, and the hazard quotient (HQ) of non-cancer risk of exposure to formaldehyde exceeded unity.     

Characterisation and seasonal variations of particles in the atmosphere of rural, urban and industrial areas: Organic compounds

Atmospheric aerosol samples(PM_(2.5–0.3), i.e., atmospheric particles ranging from 0.3 to2.5 μm) were collected during two periods: spring–summer 2008 and autumn–winter 2008–2009, using high volume samplers equipped with cascade impactors. Two sites located in the Northern France were compared in this study: a highly industrialised city(Dunkirk) and a rural site(Rubrouck). Physicochemical analysis of particulate matter(PM) was undertaken to propose parameters that could be used to distinguish the various sources and to exhibit seasonal variations but also to provide knowledge of chemical element composition for the interpretation of future toxicological studies. The study showed that PM2.5–0.3concentration in the atmosphere of the rural area remains stable along the year and was significantly lower than in the urban or industrial ones, for which concentrations increase during winter.High concentrations of polycyclic aromatic hydrocarbons(PAHs), dioxins, furans and dioxin like polychlorinated biphenyls(DL-PCBs), generated by industrial activities, traffic and municipal wastes incineration were detected in the samples. Specific criteria like Carbon Preference Index(CPI) and Combustion PAHs/Total PAHs ratio(CPAHs/TPAHs) were used to identify the possible sources of atmospheric pollution. They revealed that paraffins are mainly emitted by biogenic sources in spring–summer whereas as in the case of PAHs, they have numerous anthropogenic emission sources in autumn-winter(mainly from traffic and domestic heating).     

Volatile organic compounds in wintertime North China Plain: Insights from measurements of proton transfer reaction time-of-flight mass spectrometer (PTR-ToF-MS)

The characteristics of wintertime volatile organic compounds (VOCs) in the North China Plain (NCP) region are complicated and remain obscure. VOC measurements were conducted by a proton transfer reaction time-of-flight mass spectrometer (PTR-ToF-MS) at a rural site in the NCP from November to December 2018. Uncalibrated ions measured by PTR-ToF-MS were quantified and the overall VOC compositions were investigated by combining the measurements of PTR-ToF-MS and gas chromatography-mass spectrometer/flame ionization detector (GC-MS/FID). The measurement showed that although atmospheric VOCs concentrations are often dominated by primary emissions, the secondary formation of oxygenated VOCs (OVOCs) is non-negligible in the wintertime, i.e., OVOCs accounts for 42% ± 7% in the total VOCs (151.3 ± 75.6 ppbV). We demonstrated that PTR-MS measurements for isoprene are substantially overestimated due to the interferences of cycloalkanes. The chemical changes of organic carbon in a pollution accumulation period were investigated, which suggests an essential role of fragmentation reactions for large, chemically reduced compounds during the heavy-polluted stage in wintertime pollution. The changes of emission ratios of VOCs between winter 2011 and winter 2018 in the NCP support the positive effect of “coal to gas” strategies in curbing air pollutants. The high abundances of some key species (e.g. oxygenated aromatics) indicate the strong emissions of coal combustion in wintertime of NCP. The ratio of naphthalene to C8 aromatics was proposed as a potential indicator of the influence of coal combustion on VOCs.     

Chemical characteristics of size-resolved aerosols in winter in Beijing

Size-resolved aerosols were continuously collected by a Nano Sampler for 13 days at an urban site in Beijing during winter 2012 to measure the chemical composition of ambient aerosol particles. Data collected by the Nano Sampler and an ACSM(Aerodyne Aerosol Chemical Speciation Monitor) were compared. Between the data sets,similar trends and strong correlations were observed,demonstrating the validity of the Nano Sampler. PM10 and PM2.5concentrations during the measurement were 150.5 ± 96.0 μg/m3(mean ± standard variation)and 106.9 ± 71.6 μg/m3,respectively. The PM2.5/PM10 ratio was 0.70 ± 0.10,indicating that PM2.5dominated PM10. The aerosol size distributions showed that three size bins of 0.5–1,1–2.5 and 2.5–10 μm contributed 21.8%,23.3% and 26.0% to the total mass concentration(TMC),respectively. OM(organic matter) and SIA(secondary ionic aerosol,mainly SO42-,NO3-and NH4+) were major components of PM2.5. Secondary compounds(SIA and secondary organic carbon) accounted for half of TMC(about 49.8%) in PM2.5,and suggested that secondary aerosols significantly contributed to the serious particulate matter pollution observed in winter. Coal burning,biomass combustion,vehicle emissions and SIA were found to be the main sources of PM2.5. Mass concentrations of water-soluble ions and undetected materials,as well as their fractions in TMC,strikingly increased with deteriorating particle pollution conditions,while OM and EC(elemental carbon) exhibited different variations,with mass concentrations slightly increasing but fractions in TMC decreasing.     

Pollution levels, composition characteristics and sources of atmospheric PM2.5 in a rural area of the North China Plain during winter

The pollution levels, composition characteristics and sources of atmospheric PM_2.5 were investigated based on field measurement at a rural site in the North China Plain (NCP) from pre-heating period to heating period in winter of 2017. The hourly average concentrations of PM_2.5 frequently exceeded 150 µg/m³ and even achieved 400 µg/m³, indicating that the PM_2.5 pollution was still very serious despite the implementation of stricter control measures in the rural area. Compared with the pre-heating period, the mean concentrations of organic carbon (OC), element carbon (EC) and chlorine ion (Cl^?) during the heating period increased by 20.8%, 36.6% and 38.8%, accompanying with increments of their proportions in PM_2.5 from 37.5%, 9.8% and 5.5% to 42.9%, 12.7% and 7.2%, respectively. The significant increase of both their concentrations and proportions during the heating period was mainly ascribed to the residential coal combustion. The proportions of sulfate, nitrate and ammonium respectively increased from 9.9%, 10.9% and 9.0% in nighttime to 13.8%, 16.2% and 11.1% in daytime, implying that the daytime photochemical reactions made remarkable contributions to the secondary inorganic aerosols. The simulation results from WRF-Chem revealed that the emission of residential coal combustion in the rural area was underestimated by the current emission inventory. Six sources identified by positive matrix factorization (PMF) based on the measurement were residential coal combustion, secondary formation of inorganic aerosols, biomass burning, vehicle emission and raising dust, contributing to atmospheric PM_2.5 of 40.5%, 21.2%, 16.4%, 10.8%, 8.6% and 2.5%, respectively.     

Investigation of carbonyl compound sources at a rural site in the Yangtze River Delta region of China

Carbonyl compounds are important intermediates in atmospheric photochemistry, but their primary sources are still not understood well. In this work, carbonyls, hydrocarbons, and alkyl nitrates were continuously measured during November 2011 at a rural site in the Yangtze River Delta region of China. Mixing ratios of carbonyls and hydrocarbons showed large fluctuations during the entire measurement. The average level for total measured volatile organic compounds during the pollution episode from 25th to 27th November, 2011 was 91.6 ppb, about 7 times the value for the clean period of 7th-8th, November, 2011. To preliminarily identify toluene sources at this site, the emission ratio of toluene to benzene (T/B) during the pollution episode was determined based on photochemical ages derived from the relationship of alkyl nitrates to their parent alkanes. The calculated T/B was 5.8 ppb/ppb, significantly higher than the values of 0.2-1.7 ppb/ppb for vehicular exhaust and other combustion sources, indicating the dominant influence of industrial emissions on ambient toluene. The contributions of industrial sources to ambient carbonyls were then calculated using a multiple linear regression fit model that used toluene and alkyl nitrates as respective tracers for industrial emission and secondary production. During the pollution episode, 18.5%, 69.0%, and 52.9% of measured formaldehyde, acetaldehyde, and acetone were considered to be attributable to industrial emissions. The emission ratios relative to toluene for formaldehyde, acetaldehyde, and acetone were determined to be 0.10, 0.20 and 0.40 ppb/ppb, respectively. More research on industrial carbonyl emission characteristics is needed to understand carbonyl sources better.     

Influence of rice straw burning on the levels of polycyclic aromatic hydrocarbons in agricultural county of Taiwan

Atmospheric particulate and polycyclic aromatic hydrocarbons (PAHs) size distribution were measured at Jhu-Shan (a rural site) and Sin-Gang (a town site) in central Taiwan during the rice straw burning and non-burning periods. The concentrations of total PAHs accounting for a roughly 58% (34%) increment in the concentrations of total PAHs due to rice-straw burning. Combustion-related PAHs during burning periods were 1.54–2.57 times higher than those during non-burning periods. The mass median diameter (MMD) of 0.88–1.21 m in the particulate phase suggested that rice-straw burning generated the increase in coarse particle number. Chemical mass balance (CMB) receptor model analyses showed that the primary pollution sources at the two sites were similar. However, ricestraw burning emission was specifically identified as a significant source of PAH during burning periods at the two sites. Open burning of rice straws was estimated to contribute approximately 6.3%–24.6% to total atmospheric PAHs at the two sites.     

Air quality nearby road traffic tunnel portals： BTEX monitoring

A monitoring campaign of BTEX （benzene, toluene, ethylbenzene, o- m- and p-xylene） was carried out nearby two tunnel portals in the urban area of Naples with the aim to verify air quality in this kind of urban sites. Sampling was carried out using the active adsorption technique. Sampling time was 1 h. Ambient temperature and traffic flow measurements were carried out during each sampling operation. The results indicate that average benzene concentrations at both sites exceed the limit value of 10 μg/Nm^3 established by the European Community （EC） （Dir. 2000/69）. Concentration levels of other BTEX are relatively high as well. A correlation between BTEX concentration and two wheeler vehicle flow was observed.     

Distribution and ecological effect of mercury in Laogang landfill, Shanghai, China

Laogang landfill near Shanghai is the largest landfill in China, and receives about 10000 t of daily garbage per day, Samples of topsoil and plants were analyzed to evaluate mercury pollution from the landfill. For topsoil samples, there were significant correlations among total mercury （HgT）, combinative mercury （Hgc） and gaseous mercury （HgG）, and content of total organic carbon （TOC）, but, no significantly relationship was found between Hg content and filling time. Hg content changes in vertical profiles with time showed that the average Hgv of profiles 1992, 1996, and 2000 was similar, but their average HgG was quite different. HgT was significantly correlated with Hgc in profile 1992 and 2000, and Hgv was significantly correlated with Hg6 in profile 1996. HgG/Hgv ratio in profile samples decreased in the order of （HgG,/HgT）1992〉（HgG/HgT）1996〉〉（HgG/HgT）2000. A simple outline of Hg release in landfill could be drawn： with increasing of filling time, degradation undergoes different biodegradation, accordingly, gaseous mercury goes through small, more, and small proportion to total mercury. Distribution of Hg in plants was inhomogeneous, following the order of leaf〉root〉stem. The highest value of leaf may be associated with higher atmospheric Hg from landfill. Ligneous plants （e.g. Phyllostachys glanca, Prunus salicina and Ligustrum lucidum） are capable of enriching more Hg than herbaceous plants.     

EDTA-enhanced phytoremediation of lead contaminated soil by Bidens maximowicziana

Phytoremediation is a potential cleanup technology for the removal of heavy metals from contaminated soils.Bidens maximowicziana is a new Pb hyperaccumulator,which not only has remarkable tolerance to Pb but also extraordinary accumulation capacity for Pb.The maximum Pb concentration was 1509.3 mg/kg in roots and 2164.7 mg/kg in overground tissues.The Pb distribution order in the B. maximowicziana was:leaf>stem>root.The effect of amendments on phytoremediation was also studied.The mobility of soil Pb and the Pb concentrations in plants were both increased by EDTA application.Compared with CK(control check),EDTA application promoted translocation of Pb to overground parts of the plant.The Pb concentrations in overground parts of plants was increased from 24.23-680.56 mg/kg to 29.07-1905.57 mg/kg.This research demonstrated that B.maximowicziana appeared to be suitable for phytoremediation of Pb contaminated soil,especially,combination with EDTA.     

Decomposition of alachlor by ozonation and its mechanism

Decomposition and corresponding mechanism of alachlor, an endocrine disruptor in water by ozonation were investigated. Results showed that alachlor could not be completely mineralized by ozone alone. Many intermediates and final products were formed during the process, including aromatic compounds, aliphatic carboxylic acids, and inorganic ions. In evoluting these products, some of them with weak polarity were qualitatively identified by GC-MS. The information of inorganic ions suggested that the dechlorination was the first and the fastest step in the ozonation of alachlor.     

Enzymatic oxidation of aqueous pentachlorophenol

The influence of the nonionic surfactant Tween 80 on pentachlorophenol （PCP） oxidation catalyzed by horseradish peroxidase was studied. The surfactant was tested at concentrations below and above its critical micelle concentration （CMC）. Enhancement of PCP removal was observed at sub-CMCs. The presence of Tween 80 in the reaction mixture reduced enzyme inactivation which occurred through a combination of free radical attack and sorption by precipitated products. A simple first-order model was able to simulate time profiles for enzyme inactivation in the presence or absence of Tween 80. At supra-CMCs, the surfactant caused noticeable reductions in PCP removal, presumably through micelle partitioning of PCP which precluded the hydrophobic PCP molecule from interacting with the enzyme.     

基于综合水质标识指数和对应分析法的校园河道水质评价

以三峡大学的校园河道求索溪为研究对象,利用综合水质标识指数法确定求索溪水质类别,分析其水质时空变化规律,并利用对应分析法得出求索溪中不同监测点的主要污染因子.研究结果表明:求索溪整体的综合水质标识指数为7.423,整体水质为劣V类(地表水环境质量标准GB 3838-2002)且黑臭.从时间变化来看,求索溪4月份的水质最差,5月份次之,4、5月份所有监测点的水质都劣于V类且黑臭;8月份水质最好,水质为Ⅳ类;从空间分布来看,8个监测点综合水质标识指数均超过6.0,水质为劣V类,其中6号监测点的水质相对最好,监测点3号的水质相对最差;对应分析法得出求索溪的整体水体污染程度受总氮因子的影响最大,其次为总磷.该研究拟为求索溪及类似校园河道的水环境治理研究提供基础依据和参考.     

Effects of chitosan on growth of an aquatic plant (Hydrilla verticillata) in polluted waters with different chemical oxygen demands

Effects of chitosan on a submersed plant, Hydrilla verticillata, were investigated. Results indicated that H. venicillata could prevent ultrastructure phytotoxicities and oxidativereaction from polluted water with high chemical oxygen demand (COD). Superoxide dismutase (SOD) activity and malondialdehyde (MDA) contents in H. verticillata treated with 0.1% chitosan in wastewater increased with high COD (980 mg/L) and decreased with low COD (63 mg/L), respectively. Ultrastructural analysis showed that the stroma and grana of chloroplast basically remained normal. However, plant cells from the control experiment (untreated with chitosan) were vacuolated and the cell interval increased. The relict of protoplast moved to the center, with cells tending to disjoint. Our findings indicate that wastewater with high COD concentration can cause a substantial damage to submersed plant, nevertheless, chitosan probably could alleviate the membrane lipid peroxidization and ultrastructure phytotoxicities, and protect plant cells from stress of high COD concentration polluted water.     

Removal of cadmium using MnO2 loaded D301 resin

MnO2 loaded weak basic anion exchange resin D301 （Anion exchange resin, macroreticular weak basic styrene） as adsorbent has been prepared and applied to the removal of cadmium. The adsorption characteristics have been investigated with respect to effect of pH, equilibrium isotherms, removal kinetic data, and interference of the coexisting ions. The results indicated that the Cd^2＋ could be efficiently removed using MnO2 loaded D301 resin in the pH range of 3-8 from aqueous solutions with the co-existence of high concentration of alkali and alkaline-earth metals ions. The saturate adsorption capacity of the Cd^2＋ was 77.88 mg/g. The adsorption process followed the pseudo first-order kinetics. The equilibrium data obtained in this study accorded excellently with the Langmuir adsorption isotherm.     

Effect of coagulation pretreatment on the fouling of ultrafiltration membrane

The purpose of this study is to understand the effect and mechanism of preventing membrane fouling, by coagulation pretreatment, in terms of fractional component and molecular weight of natural organic matter （NOM）. A relatively higher molecular weight （MW） of hydrophobic compounds was responsible for a rapid decline in the ultrafiltration flux. Coagulation could effectively remove the hydrophobic organics, resulting in the increase of flux. It was found that a lower MW of neutral hydrophilic compounds, which could remove inadequately by coagulation, was responsible for the slow declining flux. The fluxes in the filtration of coagulated water and supernatant water were compared and the results showed that a lower MW of neutral hydrophilic compounds remained in the supernatant water after coagulation could be rejected by a membrane, resulting in fouling. It was also found that the coagulated flocs could absorb neutral hydrophilic compounds effectively. Therefore, with the coagulated flocs formed on the membrane surface, the flux decline could be improved.     

Penetration analysis of elements and bioleaching treatment of spent refractory for recycling

Acidithiobacillus ferrooxidans ATCC23270 and Acidithiobacillus thiooxidans TM-32 were used for bioleaching of spent refractories of aluminium and copper melting furnaces for their recycling.Firstly,penetration of elements into aluminium melting furnace refractory was investigated and it was found that up to 7 cm from surface was contaminated.Comparison on leaching efficiency by the strains ATCC23270 and TM-32 found that the strain ATCC23270 could treat larger amount of the refractories than the strain TM-32 could do.In the experiment of bioleaching of spent refractory aluminium melting furnace by the strain ATCC23270,high leaching efficiency were obtained on Al,Si,and Ca,and extremely low leaching performance was,however,shown on the rest of elements i.e.,Na,Mn,and Zn.Under the strain TM-32 use,relatively high leaching performance was recognized on Al,Si,Ca,Na,Mn,and Zn.In the experiment of bioleaching for spent refractory copper melting furnace,almost the same leaching trends were shown on Cu,Zn,Al,and Si under the strains ACTT23270 and TM-32 uses.     

Simultaneous removal of ammonium and phosphate by zeolite synthesized from coal fly ash as influenced by acid treatment

Zeolite synthesized from fly ash （ZFA） without modification is not efficient for the purification of NH4＋ and phosphate at low concentrations that occur in real effluents, despite the high potential removal capacity. To develop an effective technique to enhance the removal efficiency of ammonium and phosphate at low concentrations, ZFA was modified with acid treatment and the simultaneous removal of ammonium and phosphate in a wide range of concentration was investigated. It was seen that when compared with untreated ZFA, only the treatment by 0.01 mol/L of H2SO4 significantly improved the removal efficiency of ammonium at low initial concentrations. The behavior was well explained by the pH effect. Treatment by more concentrated H2SO4 led to the deterioration of the ZFA structure and a decrease in the cation exchange capacity. Treatment by 0.01 mol/L H2SO4 improved the removal efficiency of phosphate by ZFA at all initial P concentrations, while the treatment by concentrated H2SO4 （≥0.9 mol/L） resulted in a limited maximum phosphate immobilization capacity （PIC）. It was concluded that through a previous mild acid treatment （e.g. 0.01 mol/L of H2SO4）, ZFA can be used in the simultaneous removal of NH4＋ and P at low concentrations simulating real effluent.