发动机燃用GTL柴油的排气颗粒数量及粒径分布规律

以一台汽车电控高压共轨柴油机为样机,采用发动机尾气颗粒粒径谱仪EEPS研究了发动机燃用天然气制油(GTL柴油)的排气颗粒数量及粒径分布规律.所用燃油分别为纯柴油(G0)、纯GTL柴油(G100)及GTL柴油掺混比为10%、20%的燃料(分别表示为G10、G20).试验工况为最大转矩转速1500r.min-1和标定转速2300r.min-1的负荷特性试验,负荷百分比分别为10%、25%、50%、75%和100%.结果表明:无论燃用柴油,还是GTL柴油或混合燃料,该机排气颗粒数量随粒径变化大都呈现明显的双峰对数分布状态,其排气核态颗粒的峰值粒径在10nm附近,聚集态颗粒峰值集中出现在40～50nm之间.随着GTL柴油配比的增加,各工况下不同粒径的颗粒数量大都持续下降,其中,排气核态颗粒数量明显下降,在高速高负荷下更为显著;而聚集态颗粒也较纯柴油有一定的降幅,其中,G20和G100柴油更为明显.     

不同排放标准公交车燃用生物柴油颗粒物排放特性

基于重型底盘测功机,对比研究了满足国Ⅲ、国Ⅳ、国Ⅴ排放标准的柴油公交车分别燃用生物柴油与柴油混合燃料B0/B5/B10在中国典型城市公交车循环下的颗粒物排放特性.结果表明燃用B0/B5/B10时,国Ⅴ车相对国Ⅲ车总颗粒数量和质量排放分别降低约68.1%、56.2%、57.5%和52.7%、64.8%、88.5%,相对国Ⅳ车,总颗粒质量排放分别降低了约43.0%、47.3%和42.1%,但数量排放分别上升了约4.0%、7.6%和14.7%.国Ⅲ车核态颗粒排放主要来自高速行驶工况,而国Ⅳ、国Ⅴ车主要来自中低速行驶工况;国Ⅲ、国Ⅳ、国Ⅴ车聚集态颗粒排放主要都来自中低速行驶工况.其中在车速较低时,国Ⅴ、国Ⅳ车相对国Ⅲ车核态颗粒数量和质量排放明显降低,聚积态颗粒也有降低,但国Ⅴ车相对国Ⅳ车改善不明显,核态颗粒数量和质量排放反而增加,且随着生物柴油掺混比例的上升,增幅越明显.在高速时,国Ⅲ车核态颗粒数量和质量排放急剧增加,国Ⅴ、国Ⅳ车略有增加,且国Ⅳ车聚集态颗粒数量和质量排放明显大于国Ⅴ车和国Ⅲ车.燃用生物柴油掺混比例较大的B10时,国Ⅲ车较大粒径颗粒排放急剧恶化,聚集态颗粒数量和质量排放大幅增加,不适合推广应用较大生物柴油掺混比燃油.     

DOC+CDPF对生物柴油燃烧颗粒排放特性的影响

以一台满足国五排放法规的车用柴油机为样机,研究加装氧化催化转化器DOC与催化型颗粒捕集器CDPF(DOC+CDPF后处理装置)前后,柴油机燃用B20燃料(燃料含20%体积掺混比的生物柴油)的颗粒排放特性.结果表明,在未加装该后处理装置时,该机排气颗粒数量浓度的粒径分布呈双峰形态,B20燃料的排气颗粒数量浓度的峰值粒径在10nm和50nm附近,纯柴油的排气颗粒数量浓度的峰值粒径在50nm和200nm附近.在颗粒粒径小于120nm的区域,该机燃用B20燃料的排气颗粒数量浓度大于纯柴油.加装该后处理装置后,该机排气颗粒数量浓度的粒径分布呈多峰形态,峰值粒径在10nm、20nm和60nm附近.加装DOC+CDPF后,不论是柴油还是B20燃料,与原机相比,柴油机排气颗粒总数量下降明显,其中60~200nm粒径范围的颗粒数量浓度降幅更为显著.在相同工况下,DOC+CDPF对柴油机燃用B20燃料的颗粒总数量净化效率高于纯柴油.     

车用柴油机燃用棕榈生物柴油的颗粒物排放特性研究

在满足国Ⅳ排放法规的车用柴油机上研究了燃用不同掺混体积比例的棕榈油生物柴油的颗粒物排放特性.试验中棕榈油生物柴油的掺混比例分别为0%、10%、20%、50%和100%,采用DMS500型快速颗粒光谱仪测试分析了发动机在外特性和负荷特性时的颗粒物数量浓度、质量浓度及粒径分布.研究结果表明:随生物柴油掺混比例的增加,颗粒物质量浓度降低.燃用生物柴油后颗粒物的数量浓度在大负荷明显降低,中小负荷呈升高趋势.生物柴油的排气颗粒物呈核态和凝聚态的双峰分布特征,核态数量浓度所占比例高于柴油,凝聚态的质量浓度所占比例略低于柴油.生物柴油颗粒物的几何平均直径小于柴油.     

不同品质燃油对公交车道路颗粒排放特征的影响

以国Ⅳ排放柴油公交车为样车,研究了3种燃油公交车的颗粒数量排放特性. 3种燃油分别为纯柴油、B20燃油〔V(生物柴油)∶V(纯柴油)=2∶8〕和G20燃油〔V(天然气制油)∶V(纯柴油)=2∶8〕. 结果表明:公交车燃用3种燃油的排气颗粒数量随粒径变化均呈双峰对数分布,其中核态颗粒数量峰值粒径均为10.8 nm;聚集态颗粒数量峰值粒径则因燃料差异而不同,其中纯柴油、B20燃油和G20燃油分别为80.6、69.8和60.4 nm. 对于不同类型道路,在公交车燃用纯柴油时,其快速路下的排气颗粒数量(7.35×1015 km-1)最低,分别比主干道和次干道低47.7%和55.1%. 对于不同品质燃油而言,在全程测试线路内,燃用G20燃油的公交车排气颗粒总数量(6.92×1015 km-1)最低,较纯柴油和B20燃油分别降低了42.5%和32.4%. 其中,G20燃油排气中核态颗粒数量为1.81×1015 km-1,较纯柴油和B20燃油分别降低了3.1%和15.4%,而聚集态颗粒数量则分别降低了49.7%和37.0%. 表明公交车燃用天然气制油可有效降低颗粒排放.      

掺混聚甲氧基二甲醚对柴油机排放的影响

为研究聚甲氧基二甲醚（PODE）/柴油混合燃料对柴油机颗粒物（PM）粒径分布和各模态颗粒捕集效率的影响,将PODE按照体积百分比0%、10%、20%和30%与柴油混合,在不对柴油机做任何改动的情况下,进行排放测试,测量NO_x排放和DPF前后的颗粒粒径分布.结果表明：随着PODE掺混比提高,NO_x排放在10%~50%负荷工况下呈上升趋势,75%~100%负荷工况下呈先上升后下降的趋势;NO₂/NO_x随着PODE掺混比的提高呈上升趋势.PODE的添加可有效降低PM排放.与柴油相比,燃用PODE掺混比20%的混合燃料时,降低PM效果最好;100%负荷工况下,PM总数量浓度降低了18.93%,总体积浓度降低了31.27%.掺混PODE,使DPF对PM的捕集效果减弱,10%~50%负荷工况下较为明显,但捕集率依然可以达到95%以上.     

柴油轿车颗粒多环芳烃的排放特性

以一辆柴油轿车为研究样车,分别使用纯柴油、生物柴油掺混比例为10%的B10燃油,进行了NEDC整车循环工况试验,测取了该车HC、CO、NOx、颗粒等法规限制的排放,利用气相色谱-质谱法对采集的排气颗粒样品进行了分析,重点研究了颗粒中多环芳烃的排放特性.结果表明,与柴油相比,燃用B10燃油的HC、CO、NOx和颗粒等常规排放均有所降低;两种燃料产生的颗粒多环芳烃排放中均以荧蒽和芘最多,与纯柴油相比,燃用B10燃油产生的低环数PAHs排放略有增加,中高环数的PAHs排放降幅明显.苯并[a]芘等效毒性分析结果显示燃用B10燃油的BEQs值比纯柴油降低了21.6%,表明柴油轿车燃用生物柴油后,排气颗粒的多环芳烃毒性有所下降.     

公交车燃用生物柴油的颗粒物排放特性

采用美国TSI公司的EEPS颗粒数量及粒径分析仪,对国Ⅳ排放柴油公交车燃用纯国Ⅳ柴油BD0,纯餐饮废油制生物柴油BD100及国Ⅳ柴油和生物柴油掺混体积比分别为5%、10%、20%、50%的混合燃料(BD5、BD10、BD20、BD50)的颗粒物排放特性进行了试验研究.结果表明,颗粒物数量及质量排放随车速加速度的增加均呈逐渐增加趋势,而随生物柴油掺混比例的增加而降低;不同车速区间下,颗粒物数量排放的粒径分布均呈双峰分布;不同加速度区间下,颗粒物数量排放的粒径分布由减速时的双峰分布逐渐过渡到加速时的单峰分布;随生物柴油掺混比例的增加,聚集态颗粒物数量下降显著,且峰值向小粒径方向移动,核态颗粒物数量变化不大,颗粒物几何平均粒径Dg变小.     

汽油轿车NEDC循环超细颗粒物排放特性

以一辆采用电控燃油进气道多点喷射系统的桑塔纳汽油轿车为试验样车,采用排气颗粒数量及粒径分析仪EEPS,对该车NEDC循环的超细颗粒排放数量及颗粒粒径分布特性进行了试验研究.结果表明,NEDC循环中,车辆加速时排放的核模态颗粒、聚集态颗粒数量浓度均增加;车辆启动后40 s及EUDC循环高速工况（≥90 km.h-1）排放的超细颗粒数量浓度较高;NEDC循环的颗粒数量排放呈单峰对数分布,颗粒数量排放峰值的颗粒粒径集中于10～30 nm,几何平均粒径为24 nm;ECEⅠ、ECEⅡ～Ⅳ和EUDC循环,加速、减速、怠速及匀速驾驶工况的颗粒数量排放基本上呈单峰对数分布,颗粒数量排放峰值的颗粒粒径主要集中于10～30 nm,几何平均粒径集中于14～42 nm.该汽油车NEDC循环排放的超细颗粒主要以粒径小于50 nm的核模态颗粒为主.     

贵金属和助剂负载量对柴油公交车CDPF颗粒净化性能的影响

为研究CDPF(催化型颗粒捕集器)贵金属和助剂负载量对柴油公交车颗粒排放特性的影响,对一台满足国Ⅲ排放法规的柴油公交车进行改造,加装4种不同后处理装置,并进行道路实车排放试验.结果表明,CDPF贵金属负载量越高,排气颗粒数量浓度越低,在中高车速下尤为明显(60 km·h-1车速下贵金属负载量增加5 g·ft-3,颗粒排放总数降低70.8%).贵金属负载量对排放颗粒物中核态颗粒的影响大于聚集态颗粒.在保证对排气颗粒的净化效果的前提下,在CDPF中添加适量镧系助剂,可使贵金属和助剂负载量大幅降低.不同后处理方案对加速工况不敏感,净化效果差异较小,但减速工况,各方案对颗粒的净化效果差异较大.     

Ultrafine particle emission characteristics of diesel engine by on-board and test bench measurement

This study investigated the emission characteristics of ultrafine particles based on test bench and on-board measurements. The bench test results showed the ultrafine particle number concentration of the diesel engine to be in the range of (0.56-8.35) × 10⁸ cm^-3. The on-board measurement results illustrated that the ultrafine particles were strongly correlated with changes in real-world driving cycles. The particle number concentration was down to 2.0 × 10⁶ cm^-3 and 2.7 × 10⁷ cm^-3 under decelerating and idling operations and as high as 5.0 × 10⁸ cm^-3 under accelerating operation. It was also indicated that the particle number measured by the two methods increased with the growth of engine load at each engine speed in both cases. The particle number presented a "U" shaped distribution with changing speed at high engine load conditions, which implies that the particle number will reach its lowest level at medium engine speeds. The particle sizes of both measurements showed single mode distributions. The peak of particle size was located at about 50-80 nm in the accumulation mode particle range. Nucleation mode particles will significantly increase at low engine load operations like idling and decelerating caused by the high concentration of unburned organic compounds.     

Effects of continuously regenerating diesel particulate filters on regulated emissions and number-size distribution of particles emitted from a diesel engine

The effects of continuously regenerating diesel particulate filter (CRDPF) systems on regulated gaseous emissions, and number-size distribution and mass of particles emanated from a diesel engine have been investigated in this study. Two CRDPF units (CRDPF-1 and CRDPF-2) with di erent specifications were separately retrofitted to the engine running with European steady-state cycle (ESC). An electrical low pressure impactor (ELPI) was used for particle number-size distribution measurement and mass estimation. The conversion/reduction rate (RCR) of hydrocarbons (HC) and carbon monoxide (CO) across CRDPF-1 was 83% and 96.3%, respectively. Similarly, the RCR of HC and CO and across CRDPF-2 was 91.8% and 99.1%, respectively. The number concentration of particles and their concentration peaks; nuclei mode, accumulation mode and total particles; and particle mass were highly reduced with the CRDPF units. The nuclei mode particles at downstream of CRDPF-1 and CRDPF-2 decreased by 99.9% to 100% and 97.8% to 99.8% respectively; and the particle mass reduced by 73% to 92.2% and 35.3% to 72.4%, respectively, depending on the engine conditions. In addition, nuclei mode particles increased with the increasing of engine speed due to the heterogeneous nucleation initiated by the higher exhaust temperature, while accumulation mode particles were higher at higher loads due to the decrease in the air-to-fuel ratio (A/F) at higher loads.     

醇类汽油混合燃料EGR氛围下颗粒物排放特性研究

在一台缸内直喷(GDI)汽油机上,研究了部分负荷工况下引入EGR和添加醇类燃料对发动机颗粒物数量浓度和体积浓度排放特性的影响.实验结果表明,对于汽油、E20(乙醇在混合燃料中的体积比例为20%)、Bu20(正丁醇在混合燃料中的体积比例为20%)3种燃料而言,随着EGR率从0增加到20%,核态颗粒物数量浓度最大升幅为31.6%、110.0%、55.0%,积聚态颗粒物数量浓度最高降幅分别达21.9%、29.2%、40.9%,体积浓度最高降幅分别达45.0%、55.0%、36.6%.在EGR率为0工况下,相对于汽油燃料,E20与Bu20燃料核态颗粒物排放数量浓度降幅分别达82.4%、64.9%,积聚态颗粒物排放数量浓度降幅分别达77.0%、56.0%,体积浓度降幅分别达78.4%、52.0%,在降低颗粒物排放方面,乙醇要优于正丁醇.     

DOC技术对柴油机排放颗粒物数浓度的影响

利用ELPI(电子低压冲击器)对不同转速、不同负荷以及安装DOC(氧化催化转化器)前后颗粒物排放及粒径分布进行了研究. 结果表明:无论安装DOC与否,柴油机排放颗粒物数浓度均随发动机转速的增加而增加. 增大负荷,颗粒物数浓度峰值处的粒径也随之增大. 经过DOC催化转化后,柴油机排放颗粒物的大部分仍呈单峰正态分布,且DOC对核模态粒子的氧化转化效率较高. 经过DOC后,在低转速下,不同粒径的颗粒物数浓度均有所降低;中、高转速下,DOC对粒径大于120 nm的颗粒物数浓度无明显降低作用.      

正丁醇/柴油复合燃烧对轻型柴油机排放的影响

通过在一台轻型柴油机上加装低压共轨实现在进气歧管上的正丁醇喷射,喷射压力恒定为0.35 MPa;柴油采用缸内直喷,喷射压力恒定为120 MPa;采用自主开发的电控单元(ECU)分别控制柴油与正丁醇的喷射,实现正丁醇/柴油复合燃烧.试验研究了在2800 r·min~(-1)不同负荷下正丁醇喷射量对排放量及颗粒物粒径分布的影响.结果表明:随正丁醇喷射量增加,NO_x和碳烟排放减少,高负荷时降低幅度较大;HC和CO排放增加,低负荷时增加幅度较大;颗粒物生成总量降低且粒径分布重心左移;低负荷时相比于大粒径颗粒物,正丁醇对小粒径颗粒物数浓度的减少更明显;大粒径颗粒物减少比例与小粒径颗粒物减少比例的差距随正丁醇喷射量的增加而减小.     

甲醇柴油双燃料燃烧结合DOC/POC耦合大幅度减少发动机微粒排放的研究

对一台四缸增压中冷柴油机采用甲醇柴油双燃料模式,研究了甲醇替代率和柴油机氧化催化转化器耦合微粒催化转化器(DOC+POC)后处理装置对该发动机烟度和微粒数量、质量浓度的粒径分布特性的影响.试验结果表明,随甲醇替代率的增加,发动机烟度和微粒数浓度、质量浓度均有不同程度的降低,核态微粒浓度显著降低,聚集态微粒浓度基本保持不变.相比于DOC+POC对纯柴油发动机排气烟度25%左右的净化效率,在甲醇柴油双燃料模式下DOC+POC对排气烟度的平均净化效率在60%以上,最大达到96%,显示了该后处理技术在甲醇柴油双燃料模式下清洁排放的良好应用前景.     

Characterization of particulate matter from diesel passenger cars tested on chassis dynamometers

Emission characterization of particle number as well as particle mass from three diesel passenger cars equipped with diesel particulate filter(DPF), diesel oxidation catalyst(DOC)and exhaust gas recirculation(EGR) under the vehicle driving cycles and regulatory cycle.Total particle number emissions(PNEs) decreased gradually during speed-up of vehicle from 17.3 to 97.3 km/hr. As the average vehicle speed increases, the size-segregated peak of particle number concentration shifts to smaller size ranges of particles. The correlation analysis with various particulate components such as particle number concentration(PNC),ultrafine particle number concentration(UFPNC) and particulate matter(PM) mass was conducted to compare gaseous compounds(CO, CO_2, HC and NOx). The UFPNC and PM were not only emitted highly in Seoul during severe traffic jam conditions, but also have good correlation with hydrocarbons and NOxinfluencing high potential on secondary aerosol generation. The effect of the dilution temperature on total PNC under the New European Driving Cycle(NEDC), was slightly higher than the dilution ratio. In addition, the nuclei mode(DP: ≤ 13 nm) was confirmed to be more sensitive to the dilution temperature rather than other particle size ranges. Comparison with particle composition between vehicle speed cycles and regulatory cycle showed that sulfate was slightly increased at regulatory cycle, while other components were relatively similar. During cold start test, semivolatile nucleation particles were increased due to effect of cold environment. Research on particle formation dependent on dilution conditions of diesel passenger cars under the NEDC is important to verify impact on vehicular traffic and secondary aerosol formation in Seoul.