不锈钢-铝电极电絮凝处理含铜废水的试验研究

采用不锈钢-铝为电极的电絮凝法对含铜废水进行了处理试验研究,模拟废水铜离子浓度为150 mg/L,以废水中的铜离子浓度和COD去除率为考察指标,在电流密度为15 mA/cm2、极板间距为3 cm、pH值为7、电解时间为120 min的条件下,Cu2+的去除率平均能达到99%以上,COD的去除率亦能达到97%;在此基础上,应用于实际的电路板腐蚀液废水的处理试验,发现Cl-浓度在200 mg/L以上时,对废水先进行相关预处理也能达到较好的处理效果,该研究对进一步探讨Cl-对电絮凝的影响机理有一定的借鉴意义。     

复合式好氧生物法处理印染废水

采用将传统活性污泥法与生物膜工艺结合形成的复合式好氧生物工艺进行印染废水处理试验研究 ,取得了较好的处理效果 ,对COD去除率平均达到 6 7%以上 ,脱色率平均也达到 38%左右。在对好氧生物处理的控制中 ,DO是一个重要参数 ,从经济和处理效果考虑 ,控制在 1 5～ 2 0mg L较为合理。     

多层渗滤介质系统去除城市雨水径流有机污染物

以屋顶和机动车路面雨水径流污染物为研究对象,设计了用于去除雨水径流污染物的多层渗滤介质系统,进行污染雨水净化效果的试验研究.结果表明,系统对屋顶和机动车路面雨水径流有机污染物有明显的去除效果,CODMn平均去除率为80%左右,出水浓度小于4mg·L-1,达到了地表水Ⅱ类水质标准;BOD5的去除率达50%以上,出水值达到了地表水Ⅱ类水质标准;同时,系统的净化能力主要发生在垫层及地基土层0.3m以内,污染严重的机动车路面径流在土柱底部也能达到很好的去除效果;"砂砾科"垫层对CODMn和BOD5,的去除效果稍好于"无砂混凝土"垫层.     

新型城市污水脱氮除磷工艺的试验研究与优化设计

提出了一种改进型A2/O脱氮除磷工艺(MAAO),通过工艺试验和活性污泥2D模型对其进行运行和设计优化.结果表明,系统对COD、TN、NH 4-N和TP的平均去除率分别为85.7%、66.8%、97.35%和78.1%;当COD在300mg/L以上时,脱氮除磷效果均较好,可分别达到70%和90%以上.基于试验结果建立的MMAO工艺数学模型仿真效果良好,可对各单元组合进行优化,校核预测不利工况下的工艺运行效果,实现工艺不同工况下的运行参数优化,较好地实现新工艺的机理性优化设计和运行. MMAO稳定运行出水可达到<城镇污水处理厂污染物排放标准>(GB 18918-2002)一级B标准.由于工艺省去内回流,增加厌氧混合液部分超越提供反硝化碳源,使得运行费用明显降低;系统总停留时间比目前传统的以去除有机污染物为主的生物处理工艺略低,该工艺非常适用于对不具有脱氮除磷功能污水厂的改造.     

石灰石和黄铁矿-石灰石人工湿地净化河水的研究

利用石灰石和黄铁矿-石灰石水平潜流人工湿地处理受到污染的河水,了解它们对河水中污染物,尤其是对氮和磷的去除效果,并分析这些矿物的作用,考察了水力停留时间变化对2种人工湿地污染物净化效果的影响.结果表明,污染物去除效果的最佳停留时间出现在3 d左右,COD、TN和TP的平均去除率分别达到51%、70%和95%.在相同进水水质和水力负荷运行条件下,石灰石和黄铁矿-石灰石这2种人工湿地对COD的平均去除率分别为53.93%和51.66%,对NH4+-N的平均去除率分别为82.13%和77.43%,对TN的平均去除率分别为66%和72.06%,对TP的平均去除率分别为50.9%和97.35%.2种人工湿地对COD的去除效果差距不大,黄铁矿-石灰石人工湿地的脱氮除磷效果优于石灰石湿地,对磷有较好的去除效果,不受温度影响且净化效果稳定,适宜长期稳定运行.     

美人蕉人工湿地对城市生活污水的净化研究

研究了在土壤、黄沙、粉煤灰3种基质不同组合中的美人蕉人工湿地对城市生活污水的净化效率,并探讨了流量对城市生活污水中各污染物去除效率的影响。研究结果表明:流量对美人蕉系统处理污水效果的影响较大,实验中3L/d流量处理效果较好,对污水的综合净化效率较高;基质装填顺序对TP、TN的去除率有一定影响,而对NH3-N的去除影响不大。美人蕉系统对生活污水中COD、NH3-N、TN、TP和浊度去除效果都较好,对NH3-N的去除率高达99%,美人蕉人工湿地对城市生活污水的净化能力强。     

聚砜膜和聚乙烯膜对石油微污染水源水的处理效果研究

采用聚砜膜和聚乙烯膜对石油微污染水源水的超滤处理效果进行了中试试验,研究了原水中含油浓度、pH值、温度对两种超滤膜处理效果的影响。结果表明:当原水含油浓度≤0.5mg/L时,两种超滤膜对石油类污染物的去除率可以达到100%,当原水含油浓度≤1.0mg/L时,采用聚乙烯膜更加经济有效,当原水含油浓度>1.0mg/L时,采用聚砜膜石油类污染物的去除率可以达到90%以上,当原水含油浓度>2.0mg/L时,采用聚砜膜可以得到更为良好的处理效果;在酸性和碱性条件下,两种超滤膜对石油类污染物的去除率均随着酸性和碱性的增强而提高;当原水的温度上升时,两种超滤膜对石油类污染物的去除率明显降低。     

陶瓷行业白烟废气治理的初步研究

简述了陶瓷废气处理的技术方案、工艺流程及其废气净化装置的结构组成。以某陶瓷厂白烟废气治理为实例,废气净化装置对废气中白烟的去除效果明显,SO2和烟尘浓度从处理前的568·8mg/Nm3和324·6mg/Nm3降低到76·2·0mg/Nm3和122·4mg/Nm3,去除率分别达到86·6%和54·6%,处理后的SO2和烟尘排放浓度都达到《工业窑炉大气污染物排放标准》(GB/9078-1996)的二级标准。试验结果表明,该废气净化装置及技术解决了陶瓷行业废气的白烟污染,并具有较好的脱硫除尘效果。     

微纳气浮法用于油墨废水处理实验

采用微纳米气泡曝气的方式处理染料蓝1为原料配制的模拟水性油墨废水,以废水中的染料浓度、COD及氨氮去除效果作为考察指标,探讨废水中不同初始pH值、NaCl投加量、H₂O₂添加量对微纳米气浮法处理油墨废水的影响效果。实验结果表明:采用微纳米气浮去除油墨废水污染物能达到较好的效果,不同的反应条件有效促进了微纳气泡的曝气吸附作用,其中在pH为5的条件下处理效果最佳,染料浓度和COD去除率分别达到90.0%以上,氨氮去除率也达到75.4%。     

浅层气浮-臭氧-曝气生物滤池深度处理造纸废水研究

采用"浅层气浮-臭氧-曝气生物滤池"工艺对安徽某造纸厂二级生化出水进行深度处理试验。结果表明:聚合氯化铝投加量在120 mg/L的条件下,COD去除率达27%。臭氧-曝气生物滤池组合工艺对各种污染物均有较好的去除效果。气浮出水经臭氧-曝气生物滤池处理后,浊度降至3 NTU以下,UV254去除率达92.5%,色度去除率接近80%,COD降至50mg/L以下,完全达到GB 3544—2008《制浆造纸工业水污染物排放标准》。     

磁性树脂对地下水中硝酸盐的去除效能及影响因素

利用小试实验研究了磁性离子交换树脂对水中硝酸盐的去除效能,并探讨了地下水中常见有机物及无机离子对其去除效能的影响.结果表明,磁性离子交换树脂对纯水中20mg/L的NO3--N的交换容量为55.91mg/mL,且去除速率较快,10min基本达到去除平衡;地下水中的腐殖酸类有机物对NO3--N的去除基本没有影响,而常见阴离子具有较明显的影响,其影响程度为SO42->CO32->Cl->HCO3-;针对徐州某水厂地下水的去除研究表明,通水倍数为500BV时磁性离子交换树脂对地下水中NO3--N的去除率约为50%左右.综上,磁性离子交换树脂可以作为去除地下水中的硝酸盐一种处理技术.     

Regeneration of nano-ZnO photocatalyst by the means of soft-mechanochemical ion exchange method

Nano-crystalline ZnO particles synthesized via an ion exchange method were used in a methyl-orange photocatalytic degradation process. An ion exchange resin mixed bed system was used in the suspension for separation of nano-ZnO and methyl-orange after photocatalysis reaction. Ion exchange resin, photocatalyst and water were mixed evenly by airflow. Nano-ZnO photocatalyst and soluble carboxyl zinc were gathered in the soft-mechanochemical process simultaneously. Ion exchange reaction ZnO photocatalyst and counterion transfer process on resin were all improved. Byproducts and other inorganic ions were transfered into resin phase. Nano-ZnO photocatalyst can be regenerated and reused.     

Regeneration of spent powdered activated carbon saturated with inorganic ions by cavitation united with ion exchange method

Using ion exchange resin as transfer media, regenerate powdered activated carbon (PAC) adsorbed inorganic ions by cavitation to enhance the transfer; we studied how the regeneration time and the mass ratio of resin and PAC influence the regeneration rate respectively through re-adsorption. The result showed that the effective regeneration of PAC saturated with inorganic ions was above 90% using ion exchange resin as media and transfer carrier, the quantity of PAC did not reduced but activated in the process.     

一种修复Pb-Cd污染污泥的复合淋洗剂的研究

以某自来水厂污泥为背景泥样,人工添加重金属后泥样为研究对象,考察了葡萄糖酸、氯化钠、六偏磷酸钠复配溶液对污泥中重金属的洗脱效果.研究发现,复配淋洗剂对污泥中Pb和Cd有较好的萃取效果.形态分析表明,葡萄糖酸对污泥中的水溶态、离子交换态、碳酸盐结合态及部分弱有机结合态形式的重金属Pb、Cd有较好的萃取效果;六偏磷酸钠主要...     

Removal of cadmium using MnO2 loaded D301 resin

MnO2 loaded weak basic anion exchange resin D301 （Anion exchange resin, macroreticular weak basic styrene） as adsorbent has been prepared and applied to the removal of cadmium. The adsorption characteristics have been investigated with respect to effect of pH, equilibrium isotherms, removal kinetic data, and interference of the coexisting ions. The results indicated that the Cd^2＋ could be efficiently removed using MnO2 loaded D301 resin in the pH range of 3-8 from aqueous solutions with the co-existence of high concentration of alkali and alkaline-earth metals ions. The saturate adsorption capacity of the Cd^2＋ was 77.88 mg/g. The adsorption process followed the pseudo first-order kinetics. The equilibrium data obtained in this study accorded excellently with the Langmuir adsorption isotherm.     

Selection of magnetic anion exchange resins for the removal of dissolved organic and inorganic matters

Four magnetic anion exchange resins (MAERs) were used as adsorbents to purify drinking water. The effect of water quality (pH, temperature, ionic strength, etc.) on the performance of MAER for the removal of dissolved organic matter (DOM) was also investigated. Among the four studied MAERs, the strong base resin named NDMP-1 with high water content and enhanced exchange capacity exhibited the highest removal rate of dissolved organic carbon (DOC) (48.9% removal rate) and UV-absorbing substances (82.4% removal rate) with a resin dose of 10 mL/L after 30 min of contact time. The MAERs could also effectively remove inorganic matter such as sulfate, nitrate and fluoride. Because of the higher specific UV absorbance (SUVA) value, the DOM in the raw water was found to be removed more effectively than that in the clarified water by NDMP resin. The temperature showed a weak influence on the removal of DOC from 6 to 26℃, while a relatively strong one at 36℃. The removal of DOM by NDMP was also affected to some extent by the pH value. Moreover, increasing the sulfate concentration in the raw water could decrease the removal rates of DOC and UV-absorbing substances.     

Simultaneous adsorption of lead and cadmium on MnO2-loaded resin

MnO2-loaded D301 weak basic anion exchange resin has been used as adsorbent to simultaneously remove lead and cadmium ions from aqueous solution. The e ects of adsorbent dosage, solution pH and the coexistent ions on the adsorption were investigated. Experimental results showed that with the adsorbent dosage more than 0.6 g/L, both Pb2+ and Cd2+ were simultaneously removed at pH range 5–6. Except for HPO4 2??, the high concentration coexistent ions such as Na+, K+, Cl??, NO3??, SO4 2?? and HCO3??, showed no significant e ect on the removal e ciency of both Pb2+ and Cd2+ under the experimental conditions. The coexistence of Mg2+, Ca2+ caused the reduction of Cd2+ removal, but not for Pb2+. The adsorption equilibrium for Pb2+ and Cd2+ could be excellently described by the Langmuir isotherm model with R2 > 0.99. The maximum adsorption capacity was calculated as 80.64 mg/g for Pb2+ and 21.45 mg/g for Cd2+. The adsorption processes followed the pseudo first-order kinetics model. MnO2-loaded D301 resin has been shown to have a potential to be used as an e ective adsorbent for simultaneous removal of lead and cadmium ions from aqueous solution.     

树脂基纳米零价铁复合材料的制备及其去除重金属铅Pb(Ⅱ)的性能研究

凭借着优越的还原活性,纳米零价铁在环境污染治理和修复领域应用广泛。通过将纳米零价铁(n ZVI)颗粒负载到大孔阴离子和阳离子交换树脂上,成功制备出2种树脂基纳米零价铁复合材料。研究了2种复合材料及其载体对水溶液中Pb(Ⅱ)的去除性能,考察了不同载体功能基团对复合材料去除Pb(Ⅱ)性能的影响。结果表明:以大孔阴离子交换树脂为载体的D001-Fe0复合材料因具有离子交换和化学还原双重作用,对Pb(Ⅱ)的去除效率高、速率快。     

饮用水中卤氧化物离子色谱分析方法研究

直接大体积进样,建立生活饮用水中卤氧化物溴酸盐(BrO3-)、亚氯酸盐(ClO2-)、氯酸盐(ClO3-)含量的离子色谱(IC)法。优化的色谱条件为:Metrosep A Supp 7(250 mm)色谱柱配以Metrosep A Supp1保护柱,淋洗液为3.6 mmol/L Na2CO3与1.0 mmol/L NaHCO3;流速为0.6mL/min;进样量为100μL,抑制型电导检测器。方法结果显示:卤氧化物与常见共存阴离子完全分离,标准曲线在(5.0～400)μg/L范围内具有良好的线性关系(r>0.999),精密度高(相对标准偏差RSD<5.0%),样品加标平均回收率在90.8%~105%之间。按S/N=3,BrO3-、ClO2-、ClO3-的检出限分别为(0.9、0.7、1.0)μg/L。该方法操作简单、分离效果好,可与常见阴离子实现同时分析,灵敏度高,重现性好,适合于饮用水中消毒副产物中溴酸盐、亚氯酸盐、氯酸盐的同时测定。     

中国高矿化度矿井水脱盐技术应用现状研究

详细介绍了中国主要的水处理脱盐技术,包括化学药剂法、离子交换法、蒸馏法、电渗析法、反渗透法,并列举了各技术在高矿化度矿井水处理中的应用实例。实际经验表明化学药剂法、离子交换法和蒸馏法在高矿化度矿井水处理中均具有一定的局限性,电渗析技术脱盐效率高,适用于处理含盐量在500 mg/L~4 000mg/L的矿井水,反渗透技术脱盐效率高,应用范围广,既能够处理含盐量4 000 mg/L以下的矿井水,也能够处理含盐量10 000 mg/L的矿井水,是现阶段中国高矿化度矿井水脱盐的主要技术。