柴油表征燃料在高浓度CO2氛围下燃烧机理的分析

为研究高浓度CO₂在高温高压情况下对柴油燃烧特性的影响,提出了柴油表征燃料在CO₂/O₂氛围下的燃烧反应机理.通过量子化学计算了化学反应路径并对反应路径进行分析,最后进行柴油表征燃料燃烧的仿真.通过搭建定容燃烧弹试验台架和可视化系统进行试验与仿真分析,结果表明：在50% CO₂+50% O₂氛围下,对仿真与实验的火焰燃烧极限长度和火焰纵截面面积进行对比,最小误差分别为0.39%和0.64%,最大误差分别为8.54%和4.94%,说明此机理适用于高浓度CO₂氛围下柴油燃烧特性的研究;CO₂的化学效应在柴油表征燃料燃烧时具有促进作用,CO₂在2600 K时发生热解,热解产物CO与H自由基等发生反应可以生成着火促进剂·OH;柴油在50% CO₂+50% O₂、43% CO₂+57% O₂和35% CO₂+65% O₂氛围下的燃烧效率比空气氛围分别提高了28.2%、30.4%和33.3%.     

生物质内在碱金属催化特性的TG-FTIR实验研究

用热重分析仪和傅里叶红外光谱联用(TG-FTIR)技术对稻秆、谷壳及其经过不同预处理的水洗样、硝酸洗样进行实验研究,分析了生物质内在碱金属对其热解过程的影响.对比原样、水洗样和硝酸洗样的热解TG曲线与产气组分发现:内在碱金属的存在对生物质热解具有较大的催化作用,促进了样品半纤维组分的热分解,明显降低了最大反应速率,使样品分解能够在较低温度段完成,提高了热解过程中焦的生成率,强化了去甲烷化反应,促使热解向羟基乙醛、酸类等低小分子液体产物的方向转化,增大了CO_2和CO的生成量.     

Chemical looping combustion: A new low-dioxin energy conversion technology

Dioxin production is a worldwide concern because of its persistence and carcinogenic, teratogenic, and mutagenic effects. The pyrolysis-chemical looping combustion process of disposing solid waste is an alternative to traditional solid waste incineration developed to reduce the dioxin production. Based on the equilibrium composition of the Deacon reaction, pyrolysis gas oxidized by seven common oxygen carriers, namely, CuO, NiO, CaSO₄, CoO, Fe₂O₃, Mn₃O₄, and FeTiO₃, is studied and compared with the pyrolysis gas directly combusted by air. The result shows that the activity of the Deacon reaction for oxygen carriers is lower than that for air. For four typical oxygen carriers (CuO, NiO, Fe₂O₃, and FeTiO₃), the influences of temperature, pressure, gas composition, and tar on the Deacon reaction are discussed in detail. According to these simulation results, the dioxin production in China, Europe, the United States, and Japan is predicted for solid waste disposal by the pyrolysis-chemical looping combustion process. Thermodynamic analysis results in this paper show that chemical looping combustion can reduce dioxin production in the disposal of solid waste.     

Chemical looping combustion: A new low-dioxin energy conversion technology

Dioxin production is a worldwide concern because of its persistence and carcinogenic, teratogenic, and mutagenic effects. The pyrolysis-chemical looping combustion process of disposing solid waste is an alternative to traditional solid waste incineration developed to reduce the dioxin production. Based on the equilibrium composition of the Deacon reaction, pyrolysis gas oxidized by seven common oxygen carriers, namely, CuO, NiO, CaSO₄, CoO, Fe₂O₃, Mn₃O₄, and FeTiO₃, is studied and compared with the pyrolysis gas directly combusted by air. The result shows that the activity of the Deacon reaction for oxygen carriers is lower than that for air. For four typical oxygen carriers (CuO, NiO, Fe₂O₃, and FeTiO₃), the influences of temperature, pressure, gas composition, and tar on the Deacon reaction are discussed in detail. According to these simulation results, the dioxin production in China, Europe, the United States, and Japan is predicted for solid waste disposal by the pyrolysis-chemical looping combustion process. Thermodynamic analysis results in this paper show that chemical looping combustion can reduce dioxin production in the disposal of solid waste.     

Synthesis of porous iron hydroxy phosphate from phosphate residue and its application as a Fenton-like catalyst for dye degradation

Phosphate residue is a kind of hazardous solid waste and if not properly disposed of, could cause serious environmental contaminations. The abundant iron salt available in phosphate residue can be used to prepare photo-Fenton catalytic reagent for wastewater treatment. In this study, the phosphate residue was effectively purified by a hydrothermal recrystallization method, reaching an iron phosphate purity of 94.2%. The particles of iron phosphate were further processed with ball milling with th...     

Influence of oxygen flow rate and compost addition on reduction of organic matter in aerated waste layer containing mainly incineration residue

Landfilling municipal solid waste incineration (MSWI) residue alkalizes the waste layer, causing a subsequent decrease in microbial activity and a delay in the decomposition of organic matter. In this study, efficiencies of neutralization of the leachate and organic matter decomposition in the waste layer in a column filled with MSWI residue using aeration and compost addition were evaluated.Total organic carbon (TOC) reduction in the waste layer is large at high oxygen flow rate (OFR). To effectively accelerate TOC reduction in the waste layer to which compost was added, a high OFR exceeding that by natural ventilation was required. At day 65, the pH of the leachate when OFR was above 102mol-O2/(day·m3) was lower than that when OFR was below 101mol-O2/(day·m3). At the same OFR, the pH of waste sample was lower than that of waste sample with compost. Although leachate neutralization could be affected by compost addition, TOC reduction in the waste layer became rather small. It is possible that humic substances in compost prevent the decomposition of TOC in MSWI residue.     

Biomass-based negative emission technology options with combined heat and power generation

Biomass-based combined heat and power (CHP) generation with different carbon capture approaches is investigated in this study. Only direct carbon dioxide (CO₂) emissions are considered. The selected processes are (i) a circulating fluidized bed boiler for wood chips connected to an extraction/condensation steam cycle CHP plant without carbon capture; (ii) plant (i), but with post-combustion CO₂ capture; (iii) chemical looping combustion (CLC) of solid biomass connected to the steam cycle CHP plant; (iv) rotary kiln slow pyrolysis of biomass for biochar soil storage and direct combustion of volatiles supplying the steam cycle CHP plant with the CO₂ from volatiles combustion escaping to the atmosphere; (v) case (iv) with additional post-combustion CO₂ capture; and (vi) case (iv) with CLC of volatiles. Reasonable assumptions based on literature data are taken for the performance effects of the CO₂ capture systems and the six process options are compared. CO₂ compression to pipeline pressure is considered. The results show that both bioenergy with carbon capture and storage (BECCS) and biochar qualify as negative emission technologies (NETs) and that there is an energy-based performance advantage of BECCS over biochar because of the unreleased fuel energy in the biochar case. Additional aspects of biomass fuels (ash content and ash melting behavior) and sustainable soil management (nutrient cycles) for biomass production should be quantitatively considered in more detailed future assessments, as there may be certain biomass fuels, and environmental and economic settings where biochar application to soils is indicated rather than the full conversion of the biomass to energy and CO₂.

     

Thermal behaviors, combustion mechanisms, evolved gasses, and ash analysis of spent potlining for a hazardous waste management

An unavoidable but reusable waste so as to enhance a more circular waste utilization has been spent potlining (SPL) generated by the aluminum industry. The combustion mechanisms, evolved gasses, and ash properties of SPL were characterized dynamically in response to the elevated temperature and heating rates. Differential scanning calorimetric (DSC) results indicated an exothermic reaction behavior probably able to meet the energy needs of various industrial applications. The reaction mechanisms for the SPL combustion were best described using the 1.5-, 3- and 2.5-order reaction models. Fluoride volatilization rate of the flue gas was estimated at 2.24%. The SPL combustion emitted CO₂, HNCO, NO, and NO₂ but SO_x. The joint optimization of remaining mass, derivative thermogravimetry, and derivative DSC was achieved with the optimal temperature and heating rate combination of 783.5°C, and 5 °C/min, respectively. Interaction between temperature and heating rate exerted the strongest and weakest impact on DSC and remaining mass, respectively. The fluorine mainly as the formation of substantial NaF and CaF₂ in the residual ash. Besides, the composition and effect of environment of residual solid were evaluated. The ash slagging tendency and its mineral deposition mechanisms were elucidated in terms of turning SPL waste into a benign input to a circular waste utilization.     

Negative emissions of carbon dioxide through chemical-looping combustion (CLC) and gasification (CLG) using oxygen carriers based on manganese and iron

Carbon capture and storage (CCS) is an economically attractive strategy for avoiding carbon dioxide (CO₂) emissions from, e.g., power plants to the atmosphere. The combination of CCS and biomass combustion would result in a reduction of atmospheric CO₂, or net negative emissions, as plant growth is a form of sequestration of atmospheric carbon. Carbon capture can be achieved in a variety of ways, one of which is chemical looping. Chemical-looping combustion (CLC) and chemical looping gasification (CLG) are two promising technologies for conversion of biomass to heat and power or syngas/methane with carbon capture. There have been significant advances made with respect to CLC in the last two decades for all types of fuel, with much less research on the gasification technology. CLG offers some interesting opportunities for production of biofuels together with carbon capture and may have several advantages with respect to the bench mark indirect gasification process or dual-bed fluidized bed (DFBG) in this respect. In CLG, an oxygen carrier is used as a bed material instead of sand, which is common in indirect gasification, and this could have several advantages: (i) all generated CO₂ is present together with the syngas or methane in the fuel reactor outlet stream, thus in a concentrated stream, viable for separation and capture; (ii) the air reactor (or combustion chamber) should largely be free from trace impurities, thus preventing corrosion and fouling in this reactor; and (iii) the highly oxidizing conditions in the fuel reactor together with solid oxide surfaces should be advantageous with respect to limiting formation of tar species. In this study, two manganese ores and an iron-based waste material, LD slag, were investigated with respect to performance in these chemical-looping technologies. The materials were also impregnated with alkali (K) in order to gauge possible catalytic effects and also to establish a better understanding of the general behavior of oxygen carriers with alkali, an important component in biomass and biomass waste streams and often a precursor for high-temperature corrosion. The viability of the oxygen carriers was investigated using a synthetic biogas in a batch fluidized bed reactor. The conversion of CO, H₂, CH₄, and C₂H₄ was investigated in the temperature interval 800–950 °C. The reactivity, or oxygen transfer rate, was highest for the manganese ores, followed by the LD slag. The conversion of C₂H₄ was generally high but could largely be attributed to thermal decomposition. The K-impregnated samples showed enhanced reactivity during combustion conditions, and the Mangagran-K sample was able to achieve full conversion of benzene. The interaction of the solid material with alkali showed widely different behavior. The two manganese ores retained almost all alkali after redox testing, albeit exhibiting different migration patterns inside the particles. LD slag lost most alkali to the gas phase during testing, although some remained, possibly explaining a small difference in reactivity. In summary, the CLC and CLG processes could clearly be interesting for production of heat, power, or biofuel with negative CO₂ emissions. Manganese ores are most promising from this study, as they could absorb alkali, giving a better conversion and perhaps also inhibiting or limiting corrosion mechanisms in a combustor or gasifier.

     

Enhanced CO2 adsorptive performance of PEI/SBA-15 adsorbent using phosphate ester based surfactants as additives

In this study,a series of polyetherimide/SBA-15: 2-D hexagonal P6 mm,Santa Barbara USA(PEI/SBA-15) adsorbents modified by phosphoric ester based surfactants(including tri(2-ethylhexyl)phosphate(TEP),bis(2-ethylhexyl) phosphate(BEP) and trimethyl phosphonoacetate(TMPA))were prepared for CO_2 adsorption.Experimental results indicated that the addition of TEP and BEP had positive effects on CO_2 adsorption capacity over PEI/SBA-15.In particular,the CO_2 adsorption amount could be improved by around 20% for 45PEI–5TEP/SBA-15 compared to the additive-free adsorbent.This could be attributed to the decrease of CO_2 diffusion resistance in the PEI bulk network due to the interactions between TEP and loaded PEI molecules,which was further confirmed by adsorption kinetics results.In addition,it was also found that the cyclic performance of the TEP-modified adsorbent was better than the surfactant-free one.This could be due to two main reasons,based on the results of in situ DRIFT and TG-DSC tests.First and more importantly,adsorbed CO_2 species could be desorbed more rapidly over TEP-modified adsorbent during the thermal desorption process.Furthermore,the enhanced thermal stability after TEP addition ensured lower degradation of amine groups during adsorption/desorption cycles.     

Greenhouse gas emission and its potential mitigation process from the waste sector in a large-scale exhibition

As one of the largest human activities, World Expo is an important source of anthropogenic Greenhouse Gas emission (GHG), and the GHG emission and other environmental impacts of the Expo Shanghai 2010, where around 59,397 tons of waste was generated during 184 Expo running days, were assessed by life cycle assessment (LCA). Two scenarios, i.e., the actual and expected figures of the waste sector, were assessed and compared, and 124.01 kg CO₂-equivalent (CO₂-eq.), 4.43 kg SO₂-eq., 4.88 kg NO₃^--eq., and 3509 m³ water per ton tourist waste were found to be released in terms of global warming (GW), acidification (AC), nutrient enrichment (NE) and spoiled groundwater resources (SGWR), respectively. The total GHG emission was around 3499 ton CO₂-eq. from the waste sector in Expo Park, among which 86.47% was generated during the waste landfilling at the rate of 107.24 kg CO₂-eq., and CH₄, CO and other hydrocarbons (HC) were the main contributors. If the waste sorting process had been implemented according to the plan scenario, around 497 ton CO₂-eq. savings could have been attained. Unlike municipal solid waste, with more organic matter content, an incineration plant is more suitable for tourist waste disposal due to its high heating value, from the GHG reduction perspective.     

Greenhouse gas emission and its potential mitigation process from the waste sector in a large-scale exhibition

As one of the largest human activities, World Expo is an important source of anthropogenic Greenhouse Gas emission (GHG), and the GHG emission and other environmental impacts of the Expo Shanghai 2010, where around 59,397 tons of waste was generated during 184 Expo running days, were assessed by life cycle assessment (LCA). Two scenarios, i.e., the actual and expected figures of the waste sector, were assessed and compared, and 124.01 kg CO₂-equivalent (CO₂-eq.), 4.43 kg SO₂-eq., 4.88 kg NO₃⁻-eq., and 3509 m³ water per ton tourist waste were found to be released in terms of global warming (GW), acidification (AC), nutrient enrichment (NE) and spoiled groundwater resources (SGWR), respectively. The total GHG emission was around 3499 ton CO₂-eq. from the waste sector in Expo Park, among which 86.47% was generated during the waste landfilling at the rate of 107.24 kg CO₂-eq., and CH₄, CO and other hydrocarbons (HC) were the main contributors. If the waste sorting process had been implemented according to the plan scenario, around 497 ton CO₂-eq. savings could have been attained. Unlike municipal solid waste, with more organic matter content, an incineration plant is more suitable for tourist waste disposal due to its high heating value, from the GHG reduction perspective.     

矿物质组分对低品质生物质热解过程的影响

通过酸洗脱除低品质生物质（鸡粪与猪粪）中的矿物质组分,并使用热重分析仪对酸洗前后样品的热解行为进行了研究.结果表明,由于两种农林废物的有机组成和矿物质含量不同,导致其热解行为差异较大.鸡粪中含有大量的CaCO3,其在高温下分解放出CO2,并与鸡粪半焦中的碳发生气化反应.酸洗不但改变了禽畜粪便中矿物质的含量,而且改变了该...     

典型农药废盐热处理过程动力学特征

为了探究农药废盐热处理适宜性,采用热重分析法结合动力学模型分别对3种典型农药废盐--咪鲜胺、烟嘧磺隆和草甘膦废盐进行研究.试验结果表明咪鲜胺废盐仅有一个明显失重阶段,温度高于600℃后质量基本不发生变化,烟嘧磺隆和草甘膦废盐有两个明显失重阶段,温度分别高于300℃和450℃后失重速率明显变缓,三种废盐的明显失重温度和减重率均不相同,说明不同类型废盐的热解/燃烧特性存在明显差异;3种废盐各自的燃烧和热解的失重过程均较为相似,说明氧气的存在不会对热处理过程产生影响.并结合热处理动力学参数可知,废盐的热处理是复杂的反应过程,烟嘧磺隆废盐燃烧和热解所需活化能相近为0.297~5.894kJ/mol,热处理过程最容易发生,咪鲜胺和草甘膦废盐燃烧的活化能低于热解活化能,说明氧气会促进咪鲜胺和草甘膦废盐的热处理过程,废盐的热处理在空气气氛下即可.     

Development of a hybrid photo-bioreactor and nanoparticle adsorbent system for the removal of CO2 , and selected organic and metal co-pollutants

Fossil fuel combustion and many industrial processes generate gaseous emissions that contain a number of toxic organic pollutants and carbon dioxide (CO₂) which contribute to climate change and atmospheric pollution. There is a need for green and sustainable solutions to remove air pollutants, as opposed to conventional techniques which can be expensive, consume additional energy and generate further waste. We developed a novel integrated bioreactor combined with recyclable iron oxide nano/micro-particle adsorption interfaces, to remove CO_2, and undesired organic air pollutants using natural particles, while generating oxygen. This semi-continuous bench-scale photo-bioreactor was shown to successfully clean up simulated emission streams of up to 45% CO₂ with a conversion rate of approximately 4% CO₂ per hour, generating a steady supply of oxygen (6 mmol/hr), while nanoparticles effectively remove several undesired organic by-products. We also showed algal waste of the bioreactor can be used for mercury remediation. We estimated the potential CO₂ emissions that could be captured from our new method for three industrial cases in which, coal, oil and natural gas were used. With a 30% carbon capture system, the reduction of CO₂ was estimated to decrease by about 420,000, 320,000 and 240,000 metric tonnes, respectively for a typical 500 MW power plant. The cost analysis we conducted showed potential to scale-up, and the entire system is recyclable and sustainable. We further discuss the implications of usage of this complete system, or as individual units, that could provide a hybrid option to existing industrial setups.     

废气再循环系统参数对柴油机燃烧特征的影响

为进一步优化柴油机燃烧过程,减少燃烧污染物排放.围绕EGR（exhaust gas recirculation,废气再循环技术）废气组分和废气温度等系统参数对柴油机燃烧特征的影响机制,采用试验与模拟相结合方法,分别研究了通入废气、N₂、CO₂时以及不同EGR废气温度时对柴油机燃烧过程的影响,阐明了燃烧关键中间产物的生成规律.结果表明,①通入CO₂时,柴油机的缸内最大爆发压力和放热率峰值最低,滞燃期最长,燃烧持续期最短,·OH、H₂O₂、CH₂O·和CO等关键中间组分的生成规律与通入N₂时相反.②通入N₂时,柴油机的缸内最大爆发压力和放热率峰值最高,滞燃期最短,燃烧持续期最长并;并且通入N₂时,·OH的峰值最高,形成时刻最早,H₂O₂、CH₂O·以及CO的峰值均有所降低且形成时刻提前.③随着废气温度增加,缸内最大爆发压力降低,放热率曲线由单峰向双峰分布发展,放热率峰值有较大幅度的降低,滞燃期缩短,燃烧持续延长,缸内·OH、H₂O₂、CH₂O·以及CO的峰值均有所降低,并且生成的区域范围变窄.④废气成分中,CO₂对燃烧过程和关键中间产物的影响最大,是阻滞燃烧反应的主要气体成分,通过控制EGR废气成分和温度可以有效改善柴油机燃烧过程,拓宽EGR技术的工况使用范围.研究显示,EGR废气成分对燃烧中间产物的自由基衍化历程影响较大,有必要进一步开展EGR废气成分预处理研究,精确控制EGR废气温度,有助于改善燃烧过程,控制排放污染物中间产物的生成历程和排放量.      

The oxycoal process with cryogenic oxygen supply

Due to its large reserves, coal is expected to continue to play an important role in the future. However, specific and absolute CO₂ emissions are among the highest when burning coal for power generation. Therefore, the capture of CO₂ from power plants may contribute significantly in reducing global CO₂ emissions. This review deals with the oxyfuel process, where pure oxygen is used for burning coal, resulting in a flue gas with high CO₂ concentrations. After further conditioning, the highly concentrated CO₂ is compressed and transported in the liquid state to, for example, geological storages. The enormous oxygen demand is generated in an air-separation unit by a cryogenic process, which is the only available state-of-the-art technology. The generation of oxygen and the purification and liquefaction of the CO₂-enriched flue gas consumes significant auxiliary power. Therefore, the overall net efficiency is expected to be lowered by 8 to 12 percentage points, corresponding to a 21 to 36% increase in fuel consumption. Oxygen combustion is associated with higher temperatures compared with conventional air combustion. Both the fuel properties as well as limitations of steam and metal temperatures of the various heat exchanger sections of the steam generator require a moderation of the temperatures during combustion and in the subsequent heat-transfer sections. This is done by means of flue gas recirculation. The interdependencies among fuel properties, the amount and the temperature of the recycled flue gas, and the resulting oxygen concentration in the combustion atmosphere are investigated. Expected effects of the modified flue gas composition in comparison with the air-fired case are studied theoretically and experimentally. The different atmosphere resulting from oxygen-fired combustion gives rise to various questions related to firing, in particular, with regard to the combustion mechanism, pollutant reduction, the risk of corrosion, and the properties of the fly ash or the deposits that form. In particular, detailed nitrogen and sulphur chemistry was investigated by combustion tests in a laboratory-scale facility. Oxidant staging, in order to reduce NO formation, turned out to work with similar effectiveness as for conventional air combustion. With regard to sulphur, a considerable increase in the SO₂ concentration was found, as expected. However, the H₂S concentration in the combustion atmosphere increased as well. Further results were achieved with a pilot-scale test facility, where acid dew points were measured and deposition probes were exposed to the combustion environment. Besides CO₂ and water vapour, the flue gas contains impurities like sulphur species, nitrogen oxides, argon, nitrogen, and oxygen. The CO₂ liquefaction is strongly affected by these impurities in terms of the auxiliary power requirement and the CO₂ capture rate. Furthermore, the impurity of the liquefied CO₂ is affected as well. Since the requirements on the liquid CO₂ with regard to geological storage or enhanced oil recovery are currently undefined, the effects of possible flue gas treatment and the design of the liquefaction plant are studied over a wide range.     

污泥与煤在CO2/O2及N2/O2气氛条件下的混燃特性分析

采集了广州具有代表性的市政污泥,利用热重法对单一污泥、煤及其混合样品在CO_2/O_2及N_2/O_2气氛条件下进行了TG(热重)实验,同时计算了污泥和煤的4个燃烧特性指数,获得了燃烧的动力学参数.实验结果表明,污泥燃烧有4个燃烧阶段,包括水分析出、挥发分析出与燃烧、固定碳的燃烧和无机盐类挥发分解,其中,挥发分析出与燃烧是污泥燃烧的主要阶段;煤掺烧污泥可以提高煤的着火性能.在CO_2/O_2及N_2/O_2燃烧气氛下,增加O_2浓度,污泥与煤混合样的热重曲线整体向低温区移动,微商热重曲线峰值增大,峰宽变小,燃烧性能增强.在CO_2/O_2气氛下,O_2浓度从30%增加到60%时,污泥的挥发分释放特性指数D、可燃性指数C、燃尽指数Cb、综合燃烧特性指数S分别增加了45%、12%、18%、6%.相同O_2浓度条件下,污泥与煤在CO_2/O_2气氛下的着火性能较N_2/O_2气氛滞后,最大峰值变小,高浓度的CO_2抑制其混合样的燃烧.采用Coats-Redfern方程计算得到3个燃烧阶段反应的动力学参数,其中,增加O_2浓度,污泥与煤混合样品的质量平均表观反应活化能Em减小,并且O_2浓度越高越有利于燃烧反应的进行.污泥与煤混合燃烧取n=2可以对挥发分燃烧与固定碳燃尽峰峰前与峰后的反应模型进行描述.     

Least cost electricity generation options based on environmental impact abatement

The power sector in Thailand is the largest contributor to CO₂ emissions. There is high potential to mitigate CO₂ emission via alternative power generating plants. Alternative plants considered in this study include nuclear plants, integrated gasification combined cycle plants, biomass-based plants and supercritical thermal power plants. The biomass-based plants considered here are fueled with four types of biomass; paddy husk, municipal solid waste (MSW), fuel wood and corncob. The methodology for the optimal expansion plan of the power generating system over the planning horizon is based on the least-cost approach. The results from the least-cost planning analyses show that the nuclear alternative has the highest potential to mitigate not only CO₂ but also other airborne emissions. Moreover, the nuclear option is the most effective abatement strategy for CO₂ reduction due to its negative incremental cost of CO₂ reduction.     

典型农药废盐热处理特性及适用性

随着我国农药行业的迅速发展,农药废盐的管理和无害化处置已经成为亟待解决的环境问题.为了解决农药废盐热处理适用性的问题,推进废盐热处理工业化进程,选择盐城某企业典型农药废盐开展热重试验和动力学模型研究,分析废盐的热处理特性;基于热重试验和动力模型获取的优化参数,进一步利用管式炉模拟试验研究循环流化床焚烧炉处置废盐的可行性.结果表明:该农药废盐热解和燃烧的失重过程相似,在升温过程中一直处于缓慢失重状态,但均只有一个明显的失重阶段.其中,热解的失重阶段为170~298℃,700℃时减重率达到84.08%,燃烧的失重阶段为194~315℃,700℃时减重率达到81.45%,为了使废盐充分反应,根据热重结果确定热处理温度为350℃.热处理动力学分析表明,燃烧和热解在失重阶段反应机理相同,氧气的存在可以促进废盐的热处理过程,确定了热处理的组分为空气组分,该农药废盐属于低热值成分复杂的固体废物.在上述条件下,利用管式炉模拟试验进一步优化了废盐的热处理条件为温度350℃、停留时间45 min、空气组分、空气流量40 mL/min.对热处理后的残留物及烟气进行GC/MS分析发现,热处理法可有效降低废盐中有机污染物含量,烟气中有害物质以苯系物为主,含有少量氯苯及氯代烃类有机物.研究显示,经过管式炉热处理试验后,废盐中有机污染物的去除率达82.93%,可以有效降低有机污染物含量,从而验证了该类废盐热处理的适用性.