纳米二氧化锰/还原态氧化石墨烯复合材料催化臭氧降解苯酚的研究

制备以还原态氧化石墨烯为载体的纳米二氧化锰催化剂,并以苯酚为目标降解物,研究了其催化臭氧化性能,对影响催化臭氧化效果因素及降解机理进行了初步探讨。使用SEM、TEM和XPS对材料进行表征;纳米二氧化锰/还原态氧化石墨烯催化臭氧降解苯酚反应为准一级反应;催化剂的最佳使用量为0.2 g/L;当p H=3时,苯酚催化臭氧化去除率相对于单独臭氧提高了119.0%;催化剂连续使用4次性能良好。     

铈掺杂Ru/Al2O3催化臭氧氧化降解邻苯二甲酸二甲酯

考察了铈(Ce)的掺杂对Ru/Al2O3催化臭氧氧化邻苯二甲酸二甲酯(DMP)溶液过程的影响.结果表明,Ce的掺杂可以显著提高臭氧氧化的效果,反应100min后,TOC的去除率可以由原催化剂的61.3%提高到75.1%,而单独臭氧氧化仅有14.0%.在实验范围内,Ru和Ce同时浸渍催化效果较好,且活性组分的溶出最少,Ce的最佳掺杂量为1.0%.通过催化剂吸附试验、单独臭氧氧化试验、Ce的均相催化试验及Ru-Se/Al2O3催化剂的非均相催化实验,证明Ru-Ce/Al2O3催化剂对DMP溶液臭氧氧化体系TOC的去除率达到50%,这是基于Ru-Ce/A12O3催化剂的非均相催化作用.     

纳米TiO2/沸石/UV催化臭氧化水中硝基苯的研究

设计了O3/纳米TiO2/沸石（体系A）和O3/纳米TiO2/沸石/UV（体系B）2种催化臭氧化体系并将其用于处理水中的硝基苯,研究了影响处理效果的主要因素,并对2种方法进行了比较。结果表明,2种催化臭氧化体系都能产生大量的羟自由基,加速硝基苯的降解,其中体系B对硝基苯的降解效果最好。随着进气流量的增加、温度的升高硝基苯的降解速率都会加快。催化臭氧化反应速率遵循一级反应规律,与苯酚的初始浓度和催化剂的用量关系不大。pH值对苯酚去除率有重要的影响,随pH值的升高,苯酚去除率显著提高。叔丁醇对硝基苯的降解有很强的抑制作用。     

苯酚液相臭氧氧化和复合氧化反应动力学

推导了苯酚液相臭氧氧化和复合氧化（O3/H2O2）反应动力学模型,研究了苯酚液相臭氧氧化和复合氧化过程的降解,得出了苯酚液相臭氧氧化和复合氧化在温度288～313K和pH3.2～9.8条件下的反应动力学,探讨了反应机理,认为：在酸性(pH3.2）及弱酸性（pH6.2～6.5）时,苯酚的臭氧化和复合氧化降解反应均为O3分子的直接氧化过程;在碱性（pH9.8）条件下,苯酚复合氧化降解机理以自由基反应为主。     

纳米CNTs/Fe_3O_4修饰石墨电极电Fenton降解苯酚

以多壁碳纳米管(CNTs)为载体,采用共沉淀法制得纳米CNTs/Fe3O4材料。对纳米CNTs/Fe3O4材料进行了TEM、XRD表征。合成的纳米CNTs/Fe3O4材料修饰石墨电极用作阴极,并对苯酚进行电化学降解研究。考察了电压、pH值对苯酚降解的影响,在优化的条件下,电压为5 V、pH值为5、对150 mg/L苯酚原液降解120 min,降解率可达92%。探讨了纳米材料修饰石墨电极的电化学行为,表明纳米CNTs/Fe3O4材料修饰电极能够促进O2生成H2O2,纳米Fe3O4中的Fe与H2O2发生Fenton反应,产生·OH氧化降解苯酚。     

Pd/CeO2-Al2O3对烟气中多环芳烃的催化氧化性能研究

采用浸渍法制备了不同负载量及不同钯铈比(Pd:Ce)的Pd/CeO2-Al2O3催化剂,并结合XRD、BET、SEM、O2-TPD和H2-TPR等方法对催化剂的性质进行了表征,研究了所制备的催化剂对燃煤烟气中多环芳烃(PAHs)的催化转化效率.XRD和SEM结果表明,Ce和Pd在Al2O3表面呈高度分散状态,有利于PAHs的催化氧化.BET测试表明,Ce的引入改变了催化剂表面孔径结构,提高其比表面积.O2-TPD和H2-TPR测试表明,适当钯铈比条件下制备的催化剂有较强的储氧能力和活性.催化氧化实验结果表明,所制备的Pd/CeO2-Al2O3催化剂对PAHs具有较高的转化效率,其平均转化率均在80%以上,且PAHs的毒性当量显著降低,钯铈比对PAHs的催化氧化性能影响较大,当催化剂的钯铈比为1:1时,PAHs的转化率最高,可达90%以上.     

CuO-Ru/Al2O3 催化臭氧化降解苯乙酮的研究

采用浸渍法制备了以活性Al2O3为载体的双组分催化剂CuO-Ru/Al2O3,利用该催化剂催化臭氧化降解了苯乙酮.结果表明,贵金属钌掺杂能显著提高CuO/Al2O3催化臭氧化苯乙酮的降解效率,如在相同条件下处理30 min后,单独臭氧氧化、CuO/Al2O3/O3和CuO-Ru/Al2O3/O3对苯乙酮水溶液的COD去除率分别为6.3%、20.0%和54.0%.pH对CuO-Ru/Al2O3催化臭氧化降解苯乙酮的效率并没有影响,但与单独臭氧化相比,该催化臭氧化体系更适合在中性或酸性条件下应用.CuO-Ru/Al2O3对水中臭氧有较好的催化分解活性,臭氧分解的速率常数达2.58×10-3s-1,高于二次水中臭氧的分解速率常数1.19×10-3s-1.叔丁醇的试验结果表明,CuO-Ru/Al2O3/O3降解苯乙酮反应遵循羟基自由基(.OH)反应机制.     

CuO-Ru/A_2lO_3催化臭氧化降解苯乙酮的研究

采用浸渍法制备了以活性Al2O3为载体的双组分催化剂CuO-Ru/Al2O3,利用该催化剂催化臭氧化降解了苯乙酮.结果表明,贵金属钌掺杂能显著提高CuO/Al2O3催化臭氧化苯乙酮的降解效率,如在相同条件下处理30 min后,单独臭氧氧化、CuO/Al2O3/O3和CuO-Ru/Al2O3/O3对苯乙酮水溶液的COD去除率分别为6.3%、20.0%和54.0%.pH对CuO-Ru/Al2O3催化臭氧化降解苯乙酮的效率并没有影响,但与单独臭氧化相比,该催化臭氧化体系更适合在中性或酸性条件下应用.CuO-Ru/Al2O3对水中臭氧有较好的催化分解活性,臭氧分解的速率常数达2.58×10-3s-1,高于二次水中臭氧的分解速率常数1.19×10-3s-1.叔丁醇的试验结果表明,CuO-Ru/Al2O3/O3降解苯乙酮反应遵循羟基自由基(.OH)反应机制.     

催化臭氧化降解技术中的两个问题

探讨了有机物特性及中间产物H2O2在催化臭氧化中的作用。结果表明,有机物在自由基链反应过程中的特性直接影响催化臭氧化的降解效率。当目标有机物是对链反应具有促进作用的甲酸时,自由基引发反应可以明显提高甲酸的臭氧化效率。当目标有机物是对自由基链反应具有抑制剂作用的乙酸时,O3和Fe^2＋/O3对乙酸有着相似的降解效率。以上结果表明,自由基引发反应并不是臭氧化降解效率提高的充分条件。另外,当臭氧化过程有H2O2产生时,必须考虑类Fenton反应对臭氧化效率的影响。     

O3/H2O2氧化工艺去除水中硝基苯的研究

以硝基苯为代表性有机污染物 ,对比了臭氧化和O3/H2 O2 高级氧化工艺对水中硝基苯的去除效果 .发现与臭氧化相比 ,O3/H2 O2 高级氧化工艺可以显著地提高水中硝基苯的去除效率 .无论在臭氧化还是在O3/H2 O2 高级氧化工艺中 ,水中硝基苯的降解都主要是由OH·完成的 .通过考察O3/H2 O2 高级氧化工艺去除水中硝基苯的影响因素发现 ,在O3和过H2 O2 投量相同的条件下 ,多次投加O3和催化剂H2 O2 对水中硝基苯的处理效果明显优于一次性投加 ;在本次试验条件下 ,O3/H2 O2 高级氧化工艺降解蒸馏水和自来水中硝基苯的最优H2 O2 与O3摩尔比均为 0 5 ,HCO- 3碱度水平 (以CaCO3计 )在低于 1 0 0mg/L范围内对去除硝基苯无显著影响     

铁系混凝剂对大红染料废水处理效果研究

采用Fe(NO)3.39H2O和FeSO.47H2O混凝剂处理模拟大红染料废水,通过改变各药剂投加量及废水pH值,考察其对废水COD和色度的去除效果。实验结果表明:两种混凝剂在处理大红染料废水中都表现出了较好的脱色性能,而Fe(NO3)3.9H2O的去除性能较FeSO.47H2O更为优越。Fe(NO)3.39H2O对染料废水的脱色作用十分显著,所有的脱色率都在86%以上。当投加量为0.18 g时,脱色率达最大值93.3%;当投加量为0.24 g时,COD去除率为63.6%。FeSO.47H2O对废水色度的去除效果好于COD的去除。其最佳投加量为1.5 g,此时,脱色率达82.4%;当投加量为0.9 g时,COD去除率为51.8%。Fe(NO)3.39H2O在pH为5.0~9.0之间处理效果都较好,当pH=8时,其脱色率最高,为93.4%;FeSO.47H2O在pH为6.0~8.0之间最佳,当pH=8时,脱色率最高为83.2%。     

Simultaneous removal of NO and dichloromethane（CH2Cl2） over Nb-loaded cerium nanotubes catalyst

Herein, a series of niobium oxide supported cerium nanotubes（Ce NTs） catalysts with different loading amount of Nb₂O₅（0–10 wt.%） were prepared and used for selective catalytic reduction of NOxwith NH₃（NH₃-SCR） in the presence of CH₂Cl₂. Commercial V₂O₅-WO₃-TiO₂ catalyst was also prepared for comparison. The physcial properties and chemical properties of the Nb₂O₅ lo...     

Preparation, characterization, and photocatalytic activities of boron- and cerium-codoped TiO2

Boron- and cerium-codoped TiO2 photocatalysts were synthesized using modified sol-gel reaction process and characterized by X- ray diffraction （XRD）, X-ray photoelectron spectroscopy （XPS）, particle size distribution （PSD）, diffuse reflectance spectra （DRS）, and Brunauer-Emmett-Teller （BET）. The photocatalytic activities were evaluated by monitoring the degradation of dye Acid Red B （ARB）. The results showed that the prepared photocatalysts were mixed oxides mainly consisting of titania, ceria, and boron oxide. The structure of TiO2 could be transformed from amorphous to anatase and then to rutile by increasing calcination temperature; the transformation being accompanied by the growth of particle size without any obvious change in phase structure of CeO2. The XPS of B1.6Ce1.0-TiO2 prepared at 500℃ showed that a few boron atoms were incorporated into titania and ceria lattice, whereas others existed as B2O3. Cerium ions existed in two states, Ce^3＋ and Ce^4＋, and the atomic ratio of Ce^3＋/Ce^4＋ was 1.86. When boron and cerium were doped, the UV-Vis adsorption band wavelength showed an obvious shift toward the visible range （〈526 nm）. As the atomic ratio of Ce/Ti increased to 1.0, the absorbance edge wavelength increased to 481 nm. The absorbance edge wavelength decreased for higher cerium doping levels （Ce/Ti=2.0）. The particles size ranged from 122 to 255 nm with a domain at 168 nm （39.4%）. The degradation of ARB dye indicated that the photocatalytic activities of boron- and cerium-codoped TiO2 were much higher than those of P25 （a standard TiO2 powder）. The activities increased as the boron doping increased, whereas decreased when the Ce/Ti atomic ratio was greater than 0.5. The optimum atomic ratio of B/Ti and Ce/Ti was 1.6 and 0.5, respectively.     

焙烧温度对CeO_2(ZrO_2)/TiO_2选择性催化脱硝性能的影响

采用溶胶-凝胶法并以不同温度焙烧制备一系列CeO_2(ZrO_2)/TiO_2(CZT)催化剂,考察了CZT催化剂固相结构、酸量、比表面积等性能与催化活性的关系。采用XRD、BET、NH3-TPD、H2-TPR以及XPS等表征技术对催化剂进行表征。结果表明:焙烧温度为450℃时CZT催化剂具有最高的催化活性,其在240~400℃的温度窗口内活性均高于90%,且具有较好的抗水和抗硫中毒能力。随着焙烧温度的提高,催化剂表面的Ce和Zr原子进入体相晶格且Ce0.5Zr0.5O2向Ce0.75Zr0.25O2转变,导致催化剂的储释氧能力和氧化还原性能降低。另外,锐钛矿和金红石型TiO_2晶粒尺寸的增加,催化剂的有效比表面积和总酸量降低,因此CZT催化活性随着焙烧温度的提高而有所降低。换言之,大的比表面积、良好的氧化还原性能、表面Ce4+的富集以及酸性位的增多均有利于NH3-SCR活性的提高。     

Iron-doped Mn-Ce/TiO2 catalyst for low temperature selective catalytic reduction of NO with NH3

The catalysts of iron-doped Mn-Ce/TiO 2(Fe-Mn-Ce/TiO 2) prepared by sol-gel method were investigated for low temperature selective catalytic reduction(SCR) of NO with NH 3.It was found that the NO conversion over Fe-Mn-Ce/TiO 2 was obviously improved after iron doping compared with that over Mn-Ce/TiO 2.Fe-Mn-Ce/TiO 2 with the molar ratio of Fe/Ti = 0.1 exhibited the highest activity.The results showed that 96.8% NO conversion was obtained over Fe(0.1)-Mn-Ce/TiO 2 at 180°C at a space velocity of 50,000 hr 1.Fe-Mn-Ce/TiO 2 exhibited much higher resistance to H 2 O and SO 2 than that of Mn-Ce/TiO 2.The properties of the catalysts were characterized using X-ray diffraction(XRD),N 2 adsorption,temperature programmed desorption(NH 3-TPD and NOx-TPD),and Xray photoelectron spectroscopy(XPS) techniques.BET,NH3-TPD and NOx-TPD results showed that the specific surface area and NH3 and NOx adsorption capacity of the catalysts increased with iron doping.It was known from XPS analysis that iron valence state on the surface of the catalysts were in Fe3+ state.The doping of iron enhanced the dispersion and oxidation state of Mn and Ce on the surface of the catalysts.The oxygen concentrations on the surface of the catalysts were found to increase after iron doping.Fe-Mn-Ce/TiO2 represented a promising catalyst for low temperature SCR of NO with NH3 in the presence of H2 O and SO2.     

Performance and mechanism study for low-temperature SCR of NO with propylene in excess oxygen over Pt/TiO2 catalyst

A 0.5 wt.% Pt/TiO2 catalyst was prepared and used for the low-temperature selective catalytic reduction(SCR) of NO with C3 H6 in the presence of excess oxygen.The effects of Pt loading and O2 concentration on Pt/TiO2 catalytic performance for low-temperature SCR were investigated.It was found that optimal Pt loading was 0.5 wt.% and excess O2 favored low-temperature SCR of NOx.The mechanism of low-temperature SCR of NO with C3 H6 was investigated with respect to the behavior of adsorbed species over Pt/TiO2 at 150°C using in situ DRIFTS.The results indicated that surface nitrosyl species(Pt δ+-NO and Ti 3+-NO) and Pt 2+-CO are main reaction intermediates during the interactions of NO,C3 H6 and O2.A simplified NO decomposition mechanism for the low-temperature SCR of NO with C3 H6 was proposed.     

锰铈脱硝催化剂的制备及其再生性能研究

采用等体积浸渍法制备了一系列Mn-Ce-Ox复合氧化物脱硝催化剂用于NH3选择性催化还原(NH3-SCR)NO。考察了Mn/Ce摩尔比、焙烧温度、H2O和SO2对Mn-Ce-Ox复合氧化物脱硝催化剂活性的影响及催化剂中毒再生性能。结果表明:当NH3:NO=1:1,空速为5 000 h-1,550℃焙烧制得的Mn/Ce摩尔比为5∶1的Mn-Ce-Ox复合脱硝催化剂活性最佳,活性温度窗口为100~260℃,在此温度区间内催化剂活性大于90%。200℃时,Mn-Ce-Ox复合催化剂活性最高为97.84%;在10%(V/V)H2O蒸汽和300×10-6SO2共存条件下,200℃时,催化剂活性在开始反应2.5 h内迅速下降至53%左右,并在之后的6 h内没有明显变化;中毒催化剂经常温水洗再生处理、质量分数为3%的硝酸溶液再生处理和550℃焙烧2 h再生处理后200℃活性均能恢复到90%以上,其中中毒催化剂经质量分数为3%硝酸处理后活性恢复率最高。     

NH3-SCR performance and the resistance to SO2 for Nb doped vanadium based catalyst at low temperatures

Niobium oxide as the promoter was doped in the V/WTi catalyst for the selective catalytic reduction(SCR)of NO.The results showed that the addition of Nb_2O_5could improve the SCR activity at low temperatures and the 6 wt.%additive was an appropriate dosage.The enhanced reaction activity of adsorbed ammonia species and the improved dispersion of vanadium oxide might be the reasons for the elevation of SCR activity at low temperatures.The resistances to SO_2of 3V6Nb/WTi catalyst at different temperatures were investigated.FTIR spectrum and TG-FTIR result indicated that the deposition of ammonium sulfate species was the main deactivation reason at low temperatures,which still exhibited the reactivity with NO above 200°C on the catalyst surface.There was a synergistic effect among NH_3,H_2O and SO_2that NH_3and H_2O both accelerated the catalyst deactivation in the presence of SO_2at 175°C.The thermal treatment at 400°C could regenerate the deactivated catalyst and get SCR activity recovered.The particle and monolith catalysts both kept stable NO_xconversion at 225°C with high concentration of H_2O and SO_2during the long time tests.     

以淀粉为模板多孔纳米氧化铈的制备及其催化性能研究

为获得多孔纳米CeO₂（氧化铈）,以淀粉为生物模板,以Ce（NO₃）₃·6H₂O为铈源,在温和条件下制备出海绵状的多孔纳米CeO₂,同时考察了焙烧温度、碱液、铈源投加量对样品形貌的影响.利用XRD（X射线衍射光谱）、SEM（扫描电镜）、N₂吸附-脱附等表征手段对合成的多孔纳米CeO₂进行物相组成、微观形貌及孔径大小分布的分析.通过湿式催化过氧化试验,探究其对腈纶废水中有机物COD_Cr的催化降解性能.结果表明:①所制备的多孔纳米CeO₂具有多孔结构,孔径分布范围为2~4 nm,孔容为0.225 cm3/g,BET比表面积为256.426 m2/g;②多孔纳米CeO₂的最佳制备条件为1 g淀粉溶解于20 mL水中,加入0.02 mol Ce（NO₃）₃·6H₂O,以5%的氨水调节前驱体混合液pH,以1℃/min升至400℃,焙烧4 h,得到海绵状的多孔纳米CeO₂.③以不同形貌的CeO₂作为湿式催化反应中的催化剂,催化降解腈纶废水中有机物,其中以制备的多孔纳米CeO₂催化性能最佳,COD_Cr去除率可达82.5%.研究显示,焙烧温度、碱液、铈源投加量均可影响样品的形貌,在湿式催化过氧化处理腈纶废水试验中,多孔纳米CeO₂能显著提高废水COD_Cr的去除率.      

微波诱导催化剂Fe_2O_3/Al_2O_3制备及PEG对其活性影响

以AlCl·36H2O、FeCl·36H2O和CO(NH)22为原料,采用均匀沉淀法制备微波诱导催化剂Fe2O3/Al2O3,用X射线衍射仪(XRD)对其结构进行了表征,研究了加入聚乙二醇(PEG200)作为分散剂对产物的影响。结果表明:加入体积分数为0.05%PEG后,对于20mg/L的甲基橙模拟废水,在微波功率为900W,催化剂投加量为2g/L,处理5min后脱色率可达95.8%。