水解酸化——好氧工艺处理异丙醇工业废水

感光材料工业排出的异丙醇废水的BOD5／COcr比值为0．40左右，可生化性良好；经水解酸化处理后该废水的BOD5／CODcr比值可提高至0．5左右，平均增加了25％，证实了水解酸化菌在该工艺条件下具有提高异丙醇废水可生化性的功能。水解酸化—好氧串联工艺对该废水总的处理效果表明：在异丙醇废水CODcr进水浓度2000～3000mg／l范围内，CODcr总去除率可达90％左右，BOD5总去除率可达95％左右。水解酸化后好氧生化系统的动力学最大比降解速度K＝4．35／日，半速度常数K＝587mg／l。     

铁炭微电解法对硝化废水的处理研究

铁炭微电解法对硝化废水的处理实验表明，硝化废水经该方法处理0．5h，废水中硝基苯和硝基氯苯的去除率可达到90％，CODcr去除率可达50．6％；酸性硝基苯废水经本方法处理后BOD5/CODcr可从0．01～0．02提高至0．27～0．60，废水的可生化性明显提高。但酸性硝基氯苯废水经该方法处理后BOD5／CODcr未见明显提高。     

水解酸化-好氧工艺处理感光材料有机废水研究

感光材料有机生产废水含有多种合成有机物，其BOD5／CODer比值为0．46～0．48，可生化性良好，经水解酸化处理后该废水的BOD5／CODcr的比值可提高至0．54～056，平均增加了17％左右。水解酸化－好氧串联工艺对该废水总的处理效果表明：在废水CODer进水浓度2000～2500mg／L范围内，CODer总去除率可达95％左右，BOD5总去除率可达97％左右；水解酸化后好氧生化系统的动力学半速度常数Ks＝103mg／L，最大比降解速度K＝5．0／日。     

水解酸化-厌氧-好氧法处理苯甲酸类化工废水研究

以某化工生产企业废水为例,介绍了水解酸化-厌氧-SBR工艺处理高浓度苯甲酸类生产废水的工程实例,该工程设计规模为70m^3／d,综合进水CODcr高达15000mg／L。实践表明,该工艺处理苯甲酸类废水是一种经济有效的处理方法。利用水解酸化对废水进行预处理,不仅有效地去除了77％的CODcr,还大幅提高了废水的可生化性,使BOD5／COD值由原水的0．33升高到O．54,提高了废水的可生化性,减轻了后续生化处理的负荷,并使最终出水CODcr小于500mg／L,出水可达《污水综合排放标准》（GB8978～1996）三级排放标准。     

厌氧-混凝工艺处理造纸厂终端废水试验研究

本文报告了用厌氧 -混凝工艺处理造纸厂终端废水的实验情况 ,在最佳实验条件下 ,废水从CODcr80 6 . 7m g/ L、BOD52 10 . 5 m g/ L、SS2 15 . 7m g/ L、OD4 650 . 35 0降至 CODcr6 1. 5 m g/ L、BOD52 7. 4m g/ L、SS17.3mg/ L、OD4 650 .0 11。实验结果表明对造纸厂终端废水的治理 ,本工艺是很有实用价值的一种方法     

中试规模ABR反应器提高印染废水的可生化性

采用厌氧折流式反应器（ABR）处理印染废水.结果表明,在其他条件不做人为改变的前提下,保证PH为9左右,温度处于25℃时,水力停留时间（HRT）会明显影响出水的BOD5/CODcr（以下简写为B/C）.在HRT为10h,8.5h,12h,14h,16h,15h出水B/C均值为0.23,0.21,0.25,0.28,0.27,0.30.在HRT为15h,出水的BOD5/CODcr值明显提高,实现了可生化性的有效改善.从运行管理的经济性和提高出水的可生化性考虑,处理印染废水的HRT选择15 h为佳.     

混合染料化工废水的处理研究

在常温条件下，采用水解酸化-悬浮填料生物反应器-煤渣吸附工艺处理染料生产废水。废水进水CODcr为d740mg/L，BOD5为220mg/L，色度500倍，经处理后，CODcr去除率为80%以上，BOD5去除率为90%以上，色度去除率为90%左右，出水CODcr可达到国家排放标准。     

复合厌氧法+混凝处理啤酒废水的试验研究

上流式厌氧污泥床滤器处理啤酒废水的实验研究表明 :当试验平均温度为 2 5°C时 ,厌氧工艺出水CODcr在 2 0 0 mg/ L左右 ,经混凝沉淀处理后出水 CODcr小于 60 mg/ L;当试验平均温度为 1 5°C时 ,厌氧工艺出水CODcr在 3 0 0 mg/ L左右 ,经混凝沉淀处理后出水 CODcr小于 1 0 0 mg/ L。采用混凝后处理还可同时减少浊度和臭味。     

厌氧水解-好氧处理蒽醌废水试验研究

采用厌氧水解—好氧和单独好氧处理两种生化方法对蒽醌染整废水进行了平行对照试验。结果表明，厌氧水解—好氧处理方法可有效地提高该废水的可生化程度。当进水CODcr浓度为400mg／L、色度为800倍时，厌氧水解—好氧处理后出水CODcr可达120—170mg／L，CODcr去除率在63％以上，色度降低至150倍，明显优于单一好氧处理的出水水质。     

抗生素化学制药高浓度有机废水处理小试研究

微电解-厌氧水解-生物铁法-混凝串联工艺处理头孢类抗生素化学制药高浓度有机废水的试验研究结果表明，当微电解、厌氧水解和生物铁法水力停留时间分别为4h、24h和6h，进水CODcr 4000～4500mg/L，BOD5 800～1200mg/L，出水可达广东省《水污染物排放限值》(DB44／26-2001)第一时段一级排放标准。     

高浓度阿维菌素生产废水治理与资源回收技术研究

采用预处理一厌氧水解－二段接触氧化工艺处理阿维菌素废水，在厌氧段停留时间为１０ｈ，好氧段停留时间为６ｈ条件下，厌氧好氧段ＣＯＤ总去除率达９１％，     

稠油乳化段废水厌氧处理过程中COD与BOD5的协同变化及可生化性研究

稠油乳化段废水中的主要污染物为有机聚合物和石油类污染物，BOD5／COD值极低，可生化性差，通过厌氧处理可使污染物发生水解反应，BOD5／COD值由0．08升为0．15（288h)，与其它难降解有机废水的厌处理结果不同，在BOD5增加的同时，COD亦大幅度增加，而在全部厌氧反应过程中，TOC一直呈下降趋势，表明水样中的污染物在生物作用下不断得到消减；在COD达到最高时，石油类污染物中胶质的浓度大幅度降低，烷烃的浓度升高，说明以胶质为代表的大分子污染物因子解反应，由K2Cr2O7不能氧化状态变为可氧化状态，导致COD测量值显著升高。     

Treatment of oilfield produced water by anaerobic process coupled with micro-electrolysis

Treatment of oilfield produced water was investigated using an anaerobic process coupled with micro-electrolysis (ME), focusing on changes in chemical oxygen demand (COD) and biodegradability. Results showed that COD exhibited an abnormal change in the single anaerobic system in which it increased within the first 168 hr, but then decreased to 222 mg/L after 360 hr. The biological oxygen demand (five-day) (BOD5)/COD ratio of the water increased from 0.05 to 0.15. Hydrocarbons in the wastewater, such as pectin, degraded to small molecules during the hydrolytic acidification process. Comparatively, the e ect of ME was also investigated. The COD underwent a slight decrease and the BOD5/COD ratio of the water improved from 0.05 to 0.17 after ME. Removal of COD was 38.3% under the idealized ME conditions (pH 6.0), using iron and active carbon (80 and 40 g/L, respectively). Coupling the anaerobic process with ME accelerated the COD removal ratio (average removal was 53.3%). Gas chromatography/mass spectrometry was used to analyze organic species conversion. This integrated system appeared to be a useful option for the treatment of water produced in oilfields.     

Treatment of oilfieid produced water by anaerobic process coupled with micro-electrolysis

Treatment of oilfield produced water was investigated using an anaerobic process coupled with micro-electrolysis (ME), focusing on changes in chemical oxygen demand (COD) and biodegradability. Results showed that COD exhibited an abnormal change in the single anaerobic system in which it increased within the first 168 hr, but then decreased to 222 mg/L after 360 hr. The biological oxygen demand (five-day) (BOD5)/COD ratio of the water increased from 0.05 to 0.15. Hydrocarbons in the wastewater, such as pectin, degraded to small molecules during the hydrolytic acidification process. Comparatively, the effect of ME was also investigated. The COD underwent a slight decrease and the BOD5/COD ratio of the water improved from 0.05 to 0.17 after ME. Removal of COD was 38.3% under the idealized ME conditions (pH 6.0), using iron and active carbon (80 and 40 g/L, respectively). Coupling the anaerobic process with ME accelerated the COD removal ratio (average removal was 53.3%). Gas chromatography/mass spectrometry was used to analyze organic species conversion. This integrated system appeared to be a useful option for the treatment of water produced in oil fields.     

水解酸化─厌氧─好氧─混凝─吸附工艺处理洁霉素生产丁提高浓度有机废水

采用水解酸化厌氧好氧混凝吸附工艺处理洁霉素生产丁提高浓度有机废水，工程实践表明，ＣＯＤＣｒ和ＢＯＤ５去除率在９９％以上，所排废水各项指标达到国家排放标准。     

水解酸化─厌氧─好氧─混凝─吸附工艺处理洁霉素生产丁提高浓度有机废水

采用水解酸化 厌氧 好氧 混凝 吸附工艺处理洁霉素生产丁提高浓度有机废水，工程实践表明，ＣＯＤＣｒ和ＢＯＤ５去除率在９９％以上，所排废水各项指标达到国家排放标准。     

Treatment of a dyeing wastewater from a woolen mill using an A/O membrane bio-reactor

ＩｎｔｒｏｄｕｃｔｉｏｎＴｈｅｄｙｅｉｎｇｗａｓｔｅｗａｔｅｒｏｆｗｏｏｌｅｎｍｉｌｌｃｏｎｔａｉｎｓａｌｏｔｋｉｎｄｓｏｆｐｏｌｌｕｔａｎｔｓ,ｓｕｃｈａｓａｃｉｄｉｃｄｙｅｓ,ｄｉｓｐｅｒｓｅｄｙｅｓ,ｍｏｒｄａｎｔｄｙｅｓ,ａｕｘｉｌｉａｒｉｅｓ,ｓａｌｔｓａｎｄｓｏｏｎ .Ｔｈｅｅｆｆｌｕｅｎｔｓｆｒｏｍｗａｓｔｅｗａｔｅｒｔｒｅａｔｍｅｎｔｐｌａｎｔｓｆｏｒｔｒｅａｔｍｅｎｔｏｆｔｈｅｄｙｅｉｎｇｗａｓｔｅｗａｔｅｒｏｆｗｏｏｌｅｎｍｉｌｌｓｗｉｔｈｎｏｒｍａｌｂｉｏｌｏｇｉｃａｌｐｒｏｃｅ…     

Treatment of a dyeing wastewater from a woolen mill using an A/O membrane bio-reactor

An anaerobic/oxic membrane bioreactor (A/O MBR) was used for treatment of dyeing wastewater from a woolen mill.COD and color of the wastewater were 54-473 mg/L and 40-400 dilution time (DT) respectively. The ratio of BOD5/COD was less than 0.13. By the A/O MBR process, the average removal of COD, BOD5, color and turbidity was 82％, 96％, 71％ and 99％, respectively. The average COD, BOD5, color and turbidity of effluent was 37 nag/L, 0.8 mg/L, 40 DT and 0.44 NUT respectively. The effluent COD met the local standard of reuse water in Beijing, China. The average COD volume load of the anaerobic biological tank was 0. 0483 kgCOD/(m3·d) and that of the aeration tank of the MBR was 0. 3589 kgCOD/(m3·d). The sludge load of the MBR was 0.19 kgCOD/(kg· MLSS· d) on average and the maximum of that was 0.4 kgCOD/( kg· MLSS· d).The flux of the A/O membrane bioreactor could be remained at larger than 50 L/(h· m2· 0.1MPa). The results indicated that A/O membrane bioreactor has technical feasibility for treatment of woolen mill wastewater.     

Pretreatment of apramycin wastewater by catalytic wet air oxidation

IntroductionPharmaceuticalindustrybecomesmoreandmoreimportantallovertheworld .InChina ,therearemorethan30 0plantsmanufacturingantibioticproduction .However,theplantsoftenproducealotofwastewatercontaininghighconcentrated,colortoxicorganiccompounds.Ifthepol…     

印染废水治理方案分析

某针织印染厂年产3000吨针织高档服装布料,排放的生产废水中含有大量的有机物,COD、BOD5、色度浓度比较高。该厂选择了"厌氧水解酸化+接触氧化法+活性炭吸附"处理工艺。该工艺采用厌氧水解酸化处理工艺进行前期处理,去除大部分有机物,减轻了后续接触氧化处理工艺的压力,同时通过活性碳过滤进行脱色,达到较好的处理效果。运行结果表明,经该工艺处理后,废水中的COD、BOD5、色度等指标均能达标排放,有利于企业的可持续发展。