低热值垃圾焚烧发电运行中有关参数的监测与控制

研究适合我国国情的城市生活垃圾焚烧发电工艺,着重介绍低热值垃圾发电机组在运行过程中各主要设备的调节参数及燃烧,给水,蒸汽系统的监测与控制方法。     

城市垃圾焚烧炉内残渣性质结渣形成

以城市垃圾焚烧后的残渣为研究对象，着重地介绍城市垃焚烧炉中灰渣的形成，结构，组成等基本性质，同时借鉴燃煤技术初步探讨了城市垃圾焚烧过程中结渣的形成，对垃圾焚烧炉的正常运行提供科学的保护，对残渣的管理及综合利用有一定的意义。     

城市垃圾焚烧中PVC环境影响研究

在城市生活垃圾中，大约有一半的氯来自PVC废物。在垃圾焚烧过程中，PVC含量的增加可导致HCl产生量的增加，并有可能成为二噁Ying生成的氯源。PVC中铅含量最高，但对生活垃圾相对贡献量不大。PVC对生活垃圾的镉相对贡献量最大，而且在含PVC垃圾焚烧过程中烟气中镉的浓度也有明显增加。此外，PVC有使重金属从底灰向飞灰转移的趋势，这对于后续的底灰处置是有利的。在分析PVC对城市垃圾焚烧过程影响的基础上，本文最后提出了结论和建议。     

城市垃圾焚烧炉内残渣性质及结渣形成

以城市垃圾焚烧后的残渣为研究对象 ,着重地介绍城市垃圾焚烧炉中灰渣的形成、结构、组成等基本性质 ,同时借鉴燃煤技术初步探讨了城市垃圾焚烧过程中结渣的形成。对垃圾焚烧炉的正常运行提供科学的保证 ,对残渣的管理及综合利用有一定的意义     

城市垃圾处理方式——垃圾焚烧炉与WtE型炉排

对于以垃圾为燃料的能量回收电厂,炉排必须保证垃圾在其上有足够长的停留时间,以使燃烧充分并符合环保排放标准.以瑞士为主的ABB集团所属WtE环保设备公司,开发的水平布置、以双向运动推力炉排为特征的垃圾焚烧炉,已被成功地证明具备上述性能要求.该炉排应用于世界各地许多垃圾焚烧站,每天焚烧垃圾总量约为15000吨.垃圾能量回收电厂包括一套复杂的设备,从垃圾的进料并在炉排上燃烬,到热量回收,烟气清洗一整套过程.监视这一全过程就是电厂综合管理的内容.由于所有设备应看成一个整体,从设计到施工有必要由同一公司完成.这一手段将保证电厂有最大的运行可靠性,并符合环保规程的排放要求.     

平原典型垃圾焚烧厂周边土壤重金属分布特征及污染评价

随着固体废弃物的增加,垃圾焚烧逐步成为城市垃圾处理应用一个较为理想可行的选择。垃圾焚烧不仅可以回收能源,且相对其他处理方式其减量效果显著。垃圾焚烧厂排出的尾气中的某些特定重金属可以通过大气干湿沉降进入土壤。采用XRF 荧光光谱仪、岛津原子吸收分光光度计和测汞仪测定了杭嘉湖平原的嘉兴垃圾焚烧厂周边土壤重金属的含量,利用地统计学方法分析了该区域74个土壤样品中Cr、Mn、Cu、Pb、Fe五种重金属元素浓度的空间分布,并采用单因子指数法和内梅罗综合指数法对该地区土壤进行污染评价。结果表明：该垃圾焚烧厂周边表层土壤上述5种重金属平均含量依次为174.05、707.76、47.68、41.95、39057.89 mg·kg-1。表层富集因子分析表明表层土壤中Cu和Pb的含量受到人为影响。因子分析将5种重金属分成3类,并揭示了3类金属在该区域具有不同的空间分布特征,Cr、Mn、Fe以土壤地球化学作用（37.88%方差贡献）为主导影响因素,Cu、Pb分别以农药施用作用为主（22.06%）、垃圾焚烧源尾气排放（22.74%）为主导影响因素。污染评价结果表明该区域土壤重金属复合污染程度为轻度污染,最大污染贡献来自于Pb（单因子污染指数高达2.16）,厂区周边土壤中重金属存在累积效应,不容忽视。     

城市垃圾能量估算方法探讨

本文根据Ｄｕｌｏｎｇ公式的计算结果，建立了根据城市垃圾组成的重量百分比估算城市垃圾能量的经验公式，并对它进行了检验。估算结果与Ｄｕｌｏｎｇ公式的计算结果进行相关分析，相关系数在０．９８以上，该经验公式具有较好的推广价值，用此公式对我国部分城市垃圾的能量进行了估算。     

城市生活垃圾焚烧灰渣浸出试验

选择了城市生活垃圾焚烧炉渣中8种含量高、危害大的金属元素进行了静态和动态浸出性试验。结果表明,钙含量和温度是影响有害金属离子溶出的主要因素。对8种金属离子的浸出率和迁移规律进行了排序和分析,为灰渣安全处理和合理利用提供了科学依据。     

城市生活垃圾焚烧厂设计方案研究

本文章简要介绍了城市生活垃圾焚烧厂工艺参数、炉型结构、烟气处理、用地面积、设备配置、环境保护、工程投资和运行成本等内容的选择原则和设计方案。     

城市的景观生态学探讨

城市是一种人为活动影响比较强烈的景观，建筑物和道路组成其比较均质的外观，但其内部的物质流、能量流、人口流及信息流等却非常活跃。本文主要对城市景观的特征、结构和功能进行了分析探讨。     

Research on low emission MSW gasification and melting system

In order to eliminate secondary pollution caused by municipal solid waste (MSW) incineration, a MSW gasification and melting process is proposed. The process is expected to reduce the emission of pollutants, especially heavy-metals and dioxins. In this paper, the combustible components of MSW and simulated MSW were gasified in a lab-scale fluidized bed at 400°C–700°C when the excess air ratio (ER) was between 0.2 and 0.8. The experimental results indicated that the MSW could be gasified effectively in a fluidized bed at approximately 600°C–700°C when excess air ratio was 0.2–0.4. The melting characteristics of two typical fly ash samples from MSW incinerators were investigated. The results indicated that fly ash of pure MSW incineration could be melted at approximately 1,300°C and that of MSW and coal co-combustion could be melted at approximately 1,400°C. When temperature was over 1,100°C, more than 99.9% of the dioxins could be decomposed and most of the heavy-metals could be solidified in the slag. Based on the above experiments, two feasible MSW gasification and melting processes were proposed for low calorific value MSW: (1) sieved MSW gasification and melting system, which was based on an idea of multi-recycle; (2) gasification and melting scheme of MSW adding coal as assistant fuel.     

Recycling combustibles from aged municipal solid wastes (MSW) to improve fresh MSW incineration in Shanghai: Investigation of necessity and feasibility

Aged municipal solid wastes (MSW) excavated from landfills and dumpsites were characterized to analyze their fraction composition, moisture content, and lower heat value (LHV). The necessity and feasibility of recycling combustibles from aged MSW to improve the incineration of fresh MSW were investigated. The results showed that combustibles in aged MSW were easily separated from other components and than LHV of the separated combustibles are higher than 11000 kJ/kg. The fresh MSW are of high moisture contents with average LHV below 6500 kJ/kg, making their stable combustion difficult to maintain in MSW incinerators. For both fresh MSW and aged MSW, plastics are the main contributor to their LHV. To improve incineration of fresh MSW that are characterized with low LHV, combustibles separated from aged MSW were made into refuse derived fuel (RDF) pellets and were then added to fresh MSW by 2% wt.–5% wt. LHV variation and air supply resistance change of the MSW layer on the incinerator grate caused by the addition of RDF was checked, and no significant changes were found. No obvious difference was observed for the ‘burn-out time’ between RDF pellets and fresh MSW either. RDF made from aged MSW combustibles is found to be a promising auxiliary fuel to improve the incineration of fresh MSW, and aged MSW from old landfill cells and dumpsites can be finally disposed of jointly with fresh MSW by recycling combustible from the former to be coincinerated with the latter in the incineration plants.     

Development and prospects of municipal solid waste (MSW) incineration in China

With the lack of space for new landfills, municipal solid waste (MSW) incineration is playing an increasingly important role in municipal solid waste management in China. The literatures on certain aspects of incineration plants in China are reviewed in this paper, including the development and status of the application of MSW incineration technologies, the treatment of leachate from stored MSW, air pollution control technologies, and the status of the fly-ash control method. Energy policy and its promotion of MSW-to-energy conversion are also elucidated.     

Levels and patterns of polychlorinated biphenyls in residues from incineration of established source-classified MSW in China

Municipal solid waste (MSW) source-classified collection represents an advancement in resource cycling and secondary pollution control in China. Comparative experiments were performed to assess the levels and patterns of polychlorinated biphenyls in bottom ash, fly ash from boiler, and fly ash from bag filter from an MSW incineration plant with source-classified collection of MSW. Polychlorinated biphenyls were concentrated in the bag filter fly ash and in the bottom ash. The total amount of polychlorinated biphenyls was much lower than in fly ashes and bottom ash from traditional mixed waste incineration. Total concentration of coplanar polychlorinated biphenyls and toxic equivalent quantities were also reduced. Due to variations of feed waste, complete combustion, including continuously high incineration temperature, low CO concentrations and high air excess ratio were observed. Incineration temperature showed a negative correlation, while CO concentration showed a positive correlation with total and coplanar polychlorinated biphenyls, indicating that the latter can be reduced by controlling combustion conditions related to properties of feed waste.     

城市固体废弃物的预处理系统研究

对城市生活垃圾处置前进行有效的预处理，不仅可以减少处理量，提高处理的效果，而且可以回收部分资源性物质。由于垃圾的特性多变及处理方式的不同，统一的处理系统不仅难以达到处理垃圾的要求，而且可能造成不必要的浪费。文章针对垃圾焚的需求以及垃圾的特点，分析了垃圾焚烧炉预处理系统的设计和设计设备参数的确定，并介绍了与循环流化床垃圾焚烧炉配套的预处理系统。     

A steam dried municipal solid waste gasification and melting process

Considering high-moisture municipal solid waste (MSW) of China, a steam dried MSW gasification and melting process was proposed, the feasibility was tested, and the mass and energy balance was analyzed. Preliminary experiments were conducted using a fixed-bed drying apparatus, a 200 kg per day fluidized-bed gasifier, and a swirl melting furnace. Moisture percentage was reduced from 50% to 20% roughly when MSW was dried by slightly superheated steam of 150°C?C350°C within 40 min. When the temperature was less than 250°C, no incondensable gas was produced during the drying process. The gasifier ran at 550°C?C700°Cwith an air equivalence ratio (ER) of 0.2?C0.4. The temperature of the swirl melting furnace reached about 1240°C when the gasification ER was 0.3 and the total ER was 1.1. At these conditions, the fly ash concentration in the flue gas was 1.7 g·(Nm³)^?1, which meant over 95% fly ash was trapped in the furnace and discharged as slag. 85% of Ni and Cr were bound in the slag, as well as 60% of Cu. The mass and energy balance analysis indicates that the boiler heat efficiency of an industrial MSW incineration plant reaches 86.97% when MSW is dried by steam of 200°C. The boiler heat efficiency is sensitive to three important parameters, including the temperature of preheated MSW, the moisture percentage of dried MS Wand the fly ash percentage in the total ash.     

Performance evaluation of circulating fluidized bed incineration of municipal solid waste by multivariate outlier detection in China

This first nationwide survey was conducted to evaluate the overall performance of the circulating fluidized bed (CFB) incineration of municipal solid waste (MSW) in 2014-2015 in China. Total 23 CFB incineration power plants were evaluated. The data for monthly average flue gas emission of particles, CO, NO _x , SO₂ and HCl were collected over 12 consecutive months. The data were analyzed to assess the overall performance of CFB incineration by applying the Mahalanobis distance as a multivariate outlier detection method. Although the flue gas emission parameters had met the Chinese national emission standards, there were 11 total outliers (abnormal behavior) detected in 6 out of 23 CFB incineration power plants from the perspective of the MSWincineration performance. The results demonstrate that it is more important for a better performance of CFBs to reduce the frequencies of the MSW load changes, rather than the magnitudes of the MSW load changes, particularly reducing the frequencies in the range of 10% and more of the load changes, under the same and stable conditions. Furthermore, the overloading occurs more often than the underloading during the operation of the CFB incineration power plants in China. The frequent overloading is 0% to 30% of the designed capacity. To achieve the stable performance of CFBs in practice, an appropriately designed MSW storage capacity is suggested to build in a plant to buffer and reduce the frequency of the load changes.

Open image in new window

     

焚烧源挥发性重金属的排放对周边土壤和植被污染的研究进展

城市生活垃圾是一种成分复杂的混合废物,其中含有数量相当可观的重金属,采用焚烧法处理城市生活垃圾时,会有大量重金属因为高温而挥发进入烟气,一部分富集于焚烧飞灰中,而有少部分重金属因其挥发性较大而排放于大气中,最终随大气及雨水沉降而进入土壤和植被中,从而会对焚烧厂周边生态环境造成严重的危害。为了了解焚烧源挥发性重金属（汞（Hg）、镉（Cd）、铅（Pb）和砷（As））的排放对焚烧厂周边土壤和植被生态环境的污染状况,对近年来国内外学者在相关方面的研究状况进行了详细的文献综述,结果发现：国内学者对于焚烧源挥发性重金属的研究多限于焚烧中挥发性Hg对焚烧厂周边土壤的污染的调查研究,而对于焚烧源Cd、Pb、As对周边土壤和植被污染的调查研究相对较少;而国外学者已有的关于垃圾焚烧源重金属（Hg、Cd、Pb、As）对土壤和植被的污染研究只停留在重金属在土壤中的总的浓度和存在形态的研究,而对于挥发性重金属在焚烧源周边土壤和植被中的迁移转化规律方面的研究很缺乏,对于重金属污染物在土壤和植被中的蓄积及迁移转化规律研究较少。文章指出今后的研究应加强对挥发性重金属在焚烧厂周边土壤中的污染特征及其在土壤层以及植被中的蓄积总量和迁移转化机理的研究,这对于焚烧源挥发性重金属的污染防治以及对已被挥发性重金属污染的土壤和植被的生态修复具有重要的意义。     

Improvement of sampling and analytical methods for polychlorinated dibenzo‐p‐dioxins and dibenzofurans in environmental samples and its quantitative evaluation

Sampling of PCDDs/Fs in flue gas from a MSW incinerator was conducted using a modified apparatus of the 5 train method, which has been widely used for the sampling of PCDDs/Fs emission. In the atmosphere a high volume air sampler with special packings was used. Collection efficiencies of PCDDs/Fs were more than 98% for both samplers, using ¹³C₁₂—PCDD reference standard isomers. It was suggested that these sampling methods were adaptable for the measurements of PCDDs/Fs at sources and in the environment. To validate the applicability of existing methodologies on the PCDD/F determination, interlaboratory comparisons were undertaken. From high resolution GC/MS analysis, 2,3,7,8‐TCDD concentrations in reference ash samples were 0.052±0.013 ng/g as comparable results between the laboratories. In addition, the daily intakes of PCDDs/Fs for exposed persons in the MSW incineration facilities in Japan were estimated ranging of 0.053 to 0.28 pg/kg/day by the international toxic equivalent calculations.     

Characterization of chlorine and heavy metals for the potential recycling of bottom ash from municipal solid waste incinerators as cement additives

Bottom ash is an inevitable by-product from municipal solid waste (MSW) incineration plants. Recycling it as additives for cement production is a promising disposal method. However, the heavy metals and chlorine are the main limiting factors because of the potential environmental risks and corrosion of cement kilns. Therefore, investigating heavy metal and chlorine characteristics of bottom ash is the significant prerequisite of its reuse in cement industries. In this study, a correlative analysis was conducted to evaluate the effect of the MSW components and collection mode on the heavy metal and chlorine characteristics in bottom ash. The chemical speciation of insoluble chlorine was also investigated by synchrotron X-ray diffraction analysis. The results showed that industrial waste was the main source of heavy metals, especially Cr and Pb, in bottom ash. The higher contents of plastics and kitchen waste lead to the higher chlorine level (0.6 wt.%–0.7 wt.%) of the bottom ash. The insoluble chlorine in the MSW incineration bottom ash existed primarily as AlOCl, which was produced under the high temperature (1250°C) in incinerators.

Open image in new window