Influence of iron, nickel and cobalt on biogas production during the anaerobic fermentation of fresh residual biomass

We have investigated the dependence of the rate of the production of biogas upon the concentration of nickel, cobalt and iron at sub-toxic concentration and monitored its composition as amount of hydrogen, methane and carbon dioxide. The distribution of the added metals between the liquid and solid phase has also been monitored.

The results of our investigations show that the addition of any of the listed metals to the sludge may cause the production of a higher amount of biogas and influence the methane or carbon dioxide percentage. Conversely, the effect on the hydrogen production depends upon the metal added, the age of the active sludge used, and its adaptation to the susbtrate. As a general feature, during the acidogenesis phase, nickel reduces, while iron increases, the percentage of dihydrogen in the biogas, while cobalt has no influence.     

Control of hydrogen sulphide in digestor gas using iron salts

Different dosages of ferrous chloride and ferric chloride were added to digestors separately, and the volumes of methane and hydrogen sulphide contained in the digestor gas (biogas) were monitored. It was noted that the effects of adding of 16, 18 and 32 kg ferrous chloride/ tonne volatile solids, and 16 and 18 kg ferric chloride/tonne volatile solids were similarly effective in controlling the hydrogen sulphide levels.

According to an average amount of undigested sludge (primary sludge mixed with surplus activated sludge) of 41 tonne volatile solids produced each day during the sewage treatment process in Shatin sewage treatment works, and the required dosage of 16 kg ferric chloride/ tonne volatile solids, the amount of iron salts required should be 656 kg/day or 3.3 mg/L for the actual application, based on an average sewage flow of 200,000 m³/day.     

Effect of different gas releasing methods on anaerobic fermentative hydrogen production in batch cultures

Decreasing hydrogen partial pressure can not only increase the activity of the hydrogen enzyme but also decrease the products inhibition, so it is an appropriate method to enhance the fermentative hydrogen production from anaerobic mixed culture. The effect of biogas release method on anaerobic fermentative hydrogen production in batch culture system was compared, i.e., Owen method with intermediately release, continuous releasing method, and continuous releasing+ CO₂ absorbing. The experimental results showed that, at 35°C, initial pH 7.0 and glucose concentration of 10 g·L^-1, the hydrogen production was only 28 mL when releasing gas by Owen method, while it increased two times when releasing the biogas continuously. The cumulative hydrogen production could reach 155 mL when carbon dioxide in the gas stream was continuously absorbed by 1 mol·L^-1 NaOH. The results showed that acetate was dominated, accounting for 43% in the dissolved fermentation products in Owen method, whereas the butyrate predominated and reached 47%–53% of the total liquid end products when releasing gas continuously. It is concluded that the homoacetogenesis could be suppressed when absorbing CO₂ in the gas phase in fermentative hydrogen production system.     

Impact of Ni(II), Zn(II) and Cd(II) on biogassification of potato waste

A study was conducted on anaerobic digestion of potato waste and cattle manure mixture, inoculated with 12% inoculum and diluted to 1:1 substrate water ratio at 37 +/- 1 degrees C. Initially pH of substrate was found to be 4.5 to 5.0. Lime and sodium bicarbonate solutions were employed to adjust the pH to 7.5. Biogas production continued up to 10 and 7 days, when lime and sodium bicarbonate solutions were used to adjust the pH, respectively. Biogassification potential was studied in response to different ratio of waste and cattle manure. Biogas production rate was higher when potato waste and cattle manure were used in 50:50 ratio. Effect of two different concentrations (2.5 and 5.0 ppm) of three heavy metals viz. (Ni (II), Zn (II) and Cd (II)) on anaerobic digestion of substrate (potato waste--cattle manure, 50:50) was studied. At 2.5 ppm, all the three heavy metals increased biogas production rate over the control value. The percentage increase in biogas production over the control was highest by Cd, followed by Ni and Zn. In all the treatments, methane content of biogas increased with increase in time after feeding. Various physico-chemical parameters viz. total solids, total volatile solids, total organic carbon and chemical oxygen demand considerably declined after 7 days of digestion and decline was greater in presence of heavy metals as compared to control. The physico-chemical parameters revealed maximum decrease in the presence of 2.5-ppm concentrations of heavy metals with the substrate. Among all the three heavy metals employed in the study, Cd++ at 2.5 ppm was found to produce maximum biogas production rate. The use of three heavy metals to enhance biogas production from potato and other horticultural waste is discussed.     

Rapid start-up of mesophilic dry anaerobic digestion of kitchen waste in a continuous stirred tank reactor (CSTR)

Under mesophilic conditions (37 °C), a bench-scale experiment of dry fermentation start-up using kitchen waste was conducted in a fed-batch single phase reactor over a period of 40 days. The results showed that (1) comparing biogas production, efficiencies, and methane concentrations, three apparent different stages emerged: adaption, growth, and stability; (2) in adaption and growth stages, daily biogas production was 0–0.2 L/day and 0.2–0.4 L/day, respectively, and the concentration of methane in the biogas was 22.91% and 48.79%, respectively, with a biodegradation rate of approximately 34.72% in the adaption phase and 27.60% during the growth phase; (3) in the stability stage, the biogas production efficiency attained the maximal level and stabilized at approximately 0.6–0.4 L/day and the concentration of methane was 54.32%. Furthermore, the pH fell to 4.15, and the concentration of chemical oxygen demand increased from 51.139 to 119.295 mg/ml.     

Comparison of different valent iron on anaerobic sludge digestion: Focusing on oxidation reduction potential,dissolved organic nitrogen and microbial community

• ORP value from −278.71 to −379.80 mV showed indiscernible effects on methane yield. • Fe(II) and Fe(III) promoted more degradation of proteins and amino acids than Fe⁰. • The highest enrichment of Geobacter was noted in samples added with Fe⁰. • Cysteine was accumulated during iron enhanced anaerobic sludge digestion. • Both iron content and valence were important for methane production. This study compared effects of three different valent iron (Fe⁰, Fe(II) and Fe(III)) on enhanced anaerobic sludge digestion, focusing on the changes of oxidation reduction potential (ORP), dissolved organic nitrogen (DON), and microbial community. Under the same iron dose in range of 0−160 mg/L after an incubation period of 30 days (d), the maximum methane production rate of sludge samples dosed with respective Fe⁰, Fe(II) and Fe(III) at the same concentration showed indiscernible differences at each iron dose, regardless of the different iron valence. Moreover, their behavior in changes of ORP, DON and microbial community was different: (1) the addition of Fe⁰ made the ORP of sludge more negative, and the addition of Fe(II) and Fe(III) made the ORP of sludge less negative. However, whether being more or less negative, the changes of ORP may show unobservable effects on methane yield when it ranged from −278.71 to −379.80 mV; (2) the degradation of dissolved organic nitrogen, particularly proteins, was less efficient in sludge samples dosed with Fe⁰ compared with those dosed with Fe(II) and Fe(III) after an incubation period of 30 d. At the same dose of 160 mg/L iron, more cysteine was noted in sludge samples dosed with Fe(II) (30.74 mg/L) and Fe(III) (27.92 mg/L) compared with that dosed with Fe⁰ (21.75 mg/L); (3) Fe⁰ particularly promoted the enrichment of Geobacter, and it was 6 times higher than those in sludge samples dosed with Fe(II) and Fe(III) at the same dose of 160 mg/L iron.     

添加剂对污泥厌氧消化性能的影响

在间歇培养条件下,研究了还原型辅酶Ⅱ（NADPH）、乙酰辅酶A（Acetyl Co A）和对氨基苯甲酸（PABA）3种添加剂对污泥厌氧消化性能的影响.结果表明,3种微生物活性促进剂均能促进污泥厌氧消化产气.其中,NADPH的促进效果最为显著,消化第35 d,产甲烷量比对照组高15.90%.在污泥含固率为3%、未调初始pH（pH=6.7）和温度35℃的厌氧消化条件下,NADPH的最佳添加量为50 mg.L-1,消化第36 d,污泥累积产甲烷量127.13 mL.g-1VSS.在含固率3%、初始pH=8.5、温度55℃和NADPH添加量为50 mg.L-1的工艺条件下,污泥厌氧产气效果最佳,消化第30 d时累积产甲烷量达158.02 mL.g-1VSS.     

Efficient adsorption of carbon dioxide and methane on activated carbon prepared from glycerol with potassium acetate

In the context of global warming and the energy crisis, emissions to the atmosphere of greenhouse gases such as carbon dioxide (CO₂) and methane (CH₄) should be reduced, and biomethane from landfill biogas should be recycled. For this, there is a need for affordable technologies to capture carbon dioxide, such as adsorption of biogas on activated carbon produced from industrial wastes. Here we converted glycerol, a largely available by-product from biodiesel production, into activated carbon with the first use of potassium acetate as an activating agent. We studied adsorption of CO₂ and CH₄ on activated carbon. The results show that activated carbon adsorb CO₂ up to 20% activated carbon weight at 250 kPa, and 9% at atmospheric pressure. This is explained by high specific surface areas up to 1115 m²g⁻¹. Moreover, selectivity values up to 10.6 are observed for the separation of CO₂/CH₄. We also found that the equivalent CO₂ emissions from activated carbon synthesis are easily neutralized by their use, even in a small biogas production unit.

     

Eco-friendly approach for leaching out heavy metals from sewage sludge

Sewage sludge contains rich organic matter and nutrients essential for the growth of plants but the presence of toxic heavy metals restricts its land application. To overcome this, the study aims an eco-friendly approach for leaching out heavy metals. Sewage sludge from sewage treatment plant, Chennai, India was characterised. The analysis of total heavy metal concentration was done by digesting in nitric acid and different forms were extracted by community bureau of reference sequential method. Heavy metals: As, Cd, Cr, Cr, Ni, Pb and Zn were determined using inductively coupled plasma optical emission spectrometry Perkin Elmer Optima 5300 DV. The experimental set-up for heavy metal leaching was held for five consecutive days at different concentrations of humic acid (0.1%, 0.5% and 1%) at varied pH (5–9). Results revealed that at the end of fifth day at pH 8, 1% humic acid is capable of leaching out 75.5% cadmium, 66.0% nickel, 52.0% lead, 51.2% zinc, 31.2% copper and 8.5% cadmium from sewage sludge. Statistically positive correlation (0.7088) existed between the percentage of heavy metals leached out and the sum of soluble and reducible fractions. Thus, from ecological point of view, humic acid can be used to leach out heavy metals from sewage sludge serving the need in restoration of soil fertility upon land application.     

湿地生态系统碳汇与碳源过程的控制因子和临界条件

湿地生态系统由于其自身的结构组分特征,已成为地球表层系统中最为重要的碳汇。但是近年来对于湿地系统的不合理开发利用、降水减少等原因使其碳＂汇＂功能减弱,湿地的碳蓄积能力下降且有转变为碳＂源＂的趋势。文章从湿地生态系统的水份、植物类型、土壤厚度、微生物（底物、pH、温度、氧化还原条件）等方面总结了影响湿地碳汇/源过程的控制因子和临界交替条件。湿地水位的高低决定湿地的氧气环境,与甲烷产生量成正相关,但却与二氧化碳产生量有一定的负相关关系。湿地植物通过通气组织与根系分泌物等影响湿地碳的吸收与排放通量,湿地植株的高度、覆盖率等也是影响湿地作为碳汇与碳源的重要因素。不同深度土层由于其产甲烷菌、甲烷氧化菌等微生物活性不同导致各个土层碳吸收、排放通量的差异,通常浅层土壤中的CO2、CH4的产生率高于深层土壤。微生物的活跃程度直接影响到湿地碳的吸收与排放,影响活跃程度的因素包括湿地底物、pH、温度与氧化还原条件等。湿地底物浓度的增加会在一定程度上提高甲烷的产生率,中性或者是弱碱性环境是产甲烷菌的最适宜条件,在一定范围内温度越高,甲烷产生量越大,而温度对于二氧化碳的影响则是通过改变光合作用来实现。氧化还原电位与甲烷产生量成负相关关系,-150 mV是产甲烷菌产生甲烷的最高电位。总体上,由于湿地生态系统的复杂性和碳吸收与排放过程的复杂,以上这些因子相互作用,且在一定条件下会相互转化。最后针对如何充分发挥湿地生态系统的碳＂汇＂功能,控制湿地向碳＂源＂转化的条件措施方面进行了讨论,包括间歇灌溉、种植多年生草本植物或木本植物等来增强湿地的固碳能力。     

添加蚓粪对玉米秸秆厌氧发酵产气特性的影响

以玉米秸秆为原料,总固体(TS)含量为50g.kg-1,采用中温35℃批式发酵,考察了添加蚓粪对玉米秸秆厌氧发酵产气的影响。结果表明:玉米秸秆单独发酵时,单位TS产气量为333.3mL.g-1,甲烷产量为202.0mL.g-1,并在反应初期出现酸化现象;蚓粪与玉米秸秆TS质量比为1:1进行发酵时,单位TS产气量为400.0mL.g-1,甲烷产量为269.6mL.g-1,相对于玉米秸秆单独厌氧发酵分别提高了20.0%和35.5%,且反应过程中未出现酸化现象。说明蚓粪适合作为玉米秸秆厌氧发酵产气的添加剂。     

猪场废水厌氧消化过程中的除磷效果

采用序批式半连续厌氧消化试验方法,研究猪场废水厌氧消化过程中磷的去除情况。结果表明,水力停留时间（HRT）为1、3、6和9 d的厌氧反应器平均除磷率分别为65.0%、81.1%、82.7%和83.0%,而COD平均去除率分别为54.5%、82.3%、87.0%和85.9%。厌氧反应器除磷能力随沼气产量的增加而增加,说明厌氧反应器中磷的去除与产甲烷过程密切相关。对厌氧消化前后的污泥进行浸提后发现,厌氧消化过程中,化学反应生成磷酸盐沉淀的除磷作用十分显著,污泥中正磷酸盐,与铁结合的磷化合物（Fe-RP）,还原可溶性磷,与钙、镁离子结合的磷化合物（Ca-RP、Mg-RP）以及无机或有机聚合磷增加量分别为0.027 8～0.101 5、0.013 5～0.081 0、0.2165～0.430 5、23.4～54.8和7.2～21.5 mg.g-1;且总体而言,HRT越长,污泥中与不同金属结合的磷增加量就越大。从HRT、磷和有机物的去除效果以及沼气产气速率3个方面综合考虑,猪场废水厌氧消化反应器的HRT控制在3 d为宜。     

Heavy metals,occurrence and toxicity for plants: a review

Metal contamination issues are becoming increasingly common in India and elsewhere, with many documented cases of metal toxicity in mining industries, foundries, smelters, coal-burning power plants and agriculture. Heavy metals, such as cadmium, copper, lead, chromium and mercury are major environmental pollutants, particularly in areas with high anthropogenic pressure. Heavy metal accumulation in soils is of concern in agricultural production due to the adverse effects on food safety and marketability, crop growth due to phytotoxicity, and environmental health of soil organisms. The influence of plants and their metabolic activities affects the geological and biological redistribution of heavy metals through pollution of the air, water and soil. This article details the range of heavy metals, their occurrence and toxicity for plants. Metal toxicity has high impact and relevance to plants and consequently it affects the ecosystem, where the plants form an integral component. Plants growing in metal-polluted sites exhibit altered metabolism, growth reduction, lower biomass production and metal accumulation. Various physiological and biochemical processes in plants are affected by metals. The contemporary investigations into toxicity and tolerance in metal-stressed plants are prompted by the growing metal pollution in the environment. A few metals, including copper, manganese, cobalt, zinc and chromium are, however, essential to plant metabolism in trace amounts. It is only when metals are present in bioavailable forms and at excessive levels, they have the potential to become toxic to plants. This review focuses mainly on zinc, cadmium, copper, mercury, chromium, lead, arsenic, cobalt, nickel, manganese and iron.     

UASB和EGSB反应器中厌氧颗粒污泥生物学特性的比较

测定了实验室规模的２Ｌ ＥＧＳＢ和ＵＡＳＢ反应器中培养的厌氧颗粒污泥在不同基质中的比产甲烷活性、辅酶Ｆ４２０含量和胞外多聚酶物含量，结果表明，ＥＧＳＢ反应器颗粒污泥在葡萄糖上的比产甲烷活性、利用乙酸的甲烷菌和产氢产乙酸菌的活怀和胞外多聚物／含量高于ＵＡＳＢ反应器颗粒污泥，而ＵＡＳＢ反应器颗粒污泥中利用甲酸和氢的甲烷菌的活性以及辅酶Ｆ４２０的含量较ＥＧＳＢ反应器颗粒污泥更高，辅酶Ｆ４２０可以指示同种     

Air quality and micro-meterological monitoring of gaseous pollutants/flame emissions from burning crude petroleum in poultry house

Air quality of gaseous emissions from crude petroleum flames and fumes were monitored in a poultry house at 10 min intervals; from 10.10am–11.10am daily for 14 days. The crude petroleum burning was simulated in a metal burner, 22.86 cm high with a diameter of 17.80 cm and a thickness of 1.27 cm designed for the purpose. The micro-climate (ambient temperature, relative humidity and light intensity) of the experimental environment (poultry houses) was recorded. Results showed that the mean gaseous pollutants emitted before and during the experiments varied within the poultry house. Gases such as sulphur dioxide (SO₂), hydrogen sulphide (H₂S), methane(CH₄) and carbon monoxide (CO) were higher in the brooding than finishing phase, while volatile organic carbon (VOC) and suspended particulate matter (SPM) levels were lower at the brooding than finishing phase. The values obtained in this study for 60 min (at 10 min intervals) are far higher than the values elucidated by the Federal Environmental Protection Agency, which are outdoor air quality measurements as compared to those in this study measured indoors.     

Trace metal contents in some brands of canned beef in Nigeria

The concentrations of cadmium, chromium, copper, lead, zinc, manganese, iron, cobalt, and nickel in some brands of canned beef in Nigerian markets were determined by atomic absorption spectrophotometry. The mean concentration ranges for these metals in mg?kg^?1 were 0.02–0.37 for Cd, <0.04–0.75 for Cr, 1.1–2.4 for Cu, <0.001–1.5 for Pb, 1.1–8.0 for Zn, <0.04–0.57 for Mn, 13.8–28.8 for Fe, 0.05–0.26 for Co, and 0.8–5.9 for Ni. The estimated dietary intake of metals from these products did not indicate any risk since the values were far below the permissible dietary intakes.     

Metal passivity as mechanism of metal carcinogenesis: Chromium,nickel, iron,copper, cobalt,platinum, molybdenum

For the transition metals chromium, nickel, iron, copper, cobalt, platinum, and molybdenum, mechanisms of stable bonding in biochemistry (emphasis on carcinogenic mechanisms), chemistry, industrial chemistry, as well as epidemiological, occupational, orthopedic (implant devices) effects related to carcinogenesis, were reviewed. Hypothetically, the propensity to stable bonding (inertness), which ensures the metals’ performance capacity for consumers and industrial application, relates to their carcinogenicity. For chromium, a relationship between industrial/chemical and biological reactivity was noted for the tendency of Cr(III) ions to cause hydrolysis previous to stable bonding, as occurs during anodic passivation, leather tanning, and as indicated in biochemical studies pertaining to a mechanism of DNA condensation, which was suggested as a carcinogenic mechanism. The involvement of metal hydrolysis in both anodic passivation and biochemistry was noted also for nickel, iron, and platinum; the DNA interaction of platinum (cis-platin) is known to depend on hydrolysis. For nickel, issues of potential (V) were found important in both passivation and carcinogenicity. Comparably, the passivity behavior of cobalt and copper was found atypical, and their carcinogenicity yet unclear. Molybdenum, contained in passivated metallic implants, may relate to implant-associated carcinogenesis. Occupational carcinogenic effects were indicated for chromium, nickel, iron, and cobalt as caused by both reactive and passivated metal species. Exposure to acids and chronic respiratory irritation/infection/inflammation in workers were important cofactors in metal carcinogenesis. For wood and leather workers exposed to dust, the assumed presence in dust of metal particles abraded from alloys (sawing or cutting blades) may be a carcinogenic exposure hazard.     

城市生活垃圾有机组分厌氧发酵产氢和甲烷

为了提高能源回收效率,采用大米、土豆、生菜、瘦肉、花生油和榕树叶作为实验原料,模拟有机垃圾中普遍存在的淀粉、膳食纤维、蛋白质、脂肪和木质纤维类成分,进行厌氧发酵产氢以及对其剩余物厌氧发酵产甲烷.结果表明.在厌氧发酵产氢阶段,整个过程没有甲烷生成,大米、土豆、生菜、瘦肉、花生油和榕树叶的氢气产率分别为125、103、35、0、5和0 mL g-1(VS),能源回收效率分别为7.9%、6.8%、1.9%、0、0.1%和0.大米、土豆和生菜的氢气浓度分别为34%～59%、41%～56%和37%～70%,整个产氢阶段没有甲烷生成.在厌氧发酵产甲烷阶段,上述原料的甲烷产率分别为232、237、148、278、866和50 mL g-1(VS),生物气中甲烷含量分别为42%～70%、57%～71%、73%～77%、59%～73%、68%～80%和54%～74%.厌氧发酵联产氢气和甲烷整个过程上述原料的能源回收效率分别为56.3%、58.4%、28.8%、39.2%、81.2%和8.8%,总COD去除率分别为72.30%、81.70%、32.63%、47.59%、97.46%和11.29%.图4表5参35     

蚯蚓-稻壳炭联合堆肥对工业污泥中重金属的影响研究

蚯蚓堆肥相关研究多集中在生活污泥方面,对工业污泥的探索较少。该研究以马鞍山某钢铁污水处理站污泥为例,添加不同比例稻壳炭(2%、4%、8%),设置污泥单独堆肥、稻壳炭与污泥堆肥以及蚯蚓-稻壳炭联合污泥堆肥试验,探索蚯蚓与稻壳炭联合堆肥对工业污泥中重金属形态和生物有效性的影响。研究表明,(1)相比污泥单独堆肥,稻壳炭联合污泥堆肥能增加污泥pH、EC、TP和降低TOC、TN,而蚯蚓联合稻壳炭堆肥污泥可增加TN,并进一步增加污泥EC、TP,显著降低污泥的pH、TOC。(2)稻壳炭堆肥中重金属Zn、Cu、Pb、Cd含量因浓缩效应而上升;而蚯蚓联合稻壳炭堆肥,重金属含量显著下降,添加4%稻壳炭时,重金属Zn、Cu、Pb、Cd质量分数达到最小值,分别为856.64、137.10、158.92、15.48mg·kg-1。(3)重金属形态分析表明,随着稻壳炭比例增加,稻壳炭堆肥中重金属Zn、Cu、Pb、Cd的交换态和碳酸盐结合态转化为残渣态及铁锰氧化态的比例增大,添加8%稻壳炭时DTPA提取的有效态重金属质量分数最低,分别为705.72、47.95、50.43、4.47 mg·kg-1;蚯蚓-稻壳炭联合堆肥会使得污泥中重金属交换态、碳酸盐结合态、铁锰结合态和有机结合态均向残渣态转化,添加4%稻壳炭与蚯蚓的协同转化能力最大,Zn、Cu、Pb、Cd有效态重金属质量分数分别为629.84、38.63、36.76、1.63mg·kg-1,说明稻壳炭添加入蚯蚓堆肥可进一步降低工业污泥中重金属有效性,使重金属钝化。本研究可为稻壳炭联合蚯蚓堆肥处理工业污泥提供参考和科学依据。     

Methane and carbon dioxide dynamics in wetland mesocosms: effects of hydrology and soils.

Methane and carbon dioxide fluxes in created and restored wetlands, and the influence of hydrology and soils on these fluxes, have not been extensively documented. Minimizing methane fluxes while maximizing productivity is a relevant goal for wetland restoration and creation projects. In this study we used replicated wetland mesocosms to investigate relationships between contrasting hydrologic and soil conditions, and methane and carbon dioxide fluxes in emergent marsh systems. Hydrologic treatments consisted of an intermittent flooding regime vs. continuously inundated conditions, and soil treatments utilized hydric vs. non-hydric soils. Diurnal patterns of methane flux were examined to shed light on the relationship between emergent macrophytes and methane emissions for comparison with vegetation-methane relationships reported from natural wetlands. Microbially available organic carbon content was significantly greater in hydric soils than nonhydric soils, despite similar organic matter contents in the contrasting soil types. Mesocosms with hydric soils exhibited the greatest rates of methane flux regardless of hydrology, but intermittent inundation of hydric soils produced significantly lower methane fluxes than continuous inundatation of hydric soils. Methane fluxes were not affected significantly by hydrologic regime in mesocosms containing non-hydric soils. There were no diurnal differences in methane flux, and carbon dioxide and methane fluxes were not significantly correlated. The highest rates of CO2 uptake occurred in the continuously inundated treatment with non-hydric soils, and there were no significant differences in nighttime respiration rates between the treatments. Implications for hydrologic design of created and restored wetlands are discussed.