A pulsed switching peroxi-coagulation process to control hydroxyl radical production and to enhance 2,4-Dichlorophenoxyacetic acid degradation

• A new pulsed switching peroxi-coagulation (PSPC) system was developed. • The EC_T for 2,4-D removal in the PSPC was lower than that in the EF. • The iron consumption for 2,4-D removal in the PSPC was lower than that in the PC. The aim of this study was to develop a new pulsed switching peroxi-coagulation system to control hydroxyl radical (?OH) production and to enhance 2,4-Dichlorophenoxyacetic acid (2,4-D) degradation. The system was constructed with a sacrifice iron anode, a Pt anode, and a gas diffusion cathode. Production of H₂O₂ and Fe²⁺ was controlled separately by time delayers with different pulsed switching frequencies. Under current densities of 5.0 mA/cm² (H₂O₂) and 0.5 mA/cm² (Fe²⁺), the ?OH production was optimized with the pulsed switching frequency of 1.0 s (H₂O₂):0.3 s (Fe²⁺) and the ratio of H₂O₂ to Fe²⁺ molar concentrations of 6.6. Under the optimal condition, 2,4-D with an initial concentration of 500 mg/L was completely removed in the system within 240 min. The energy consumption for the 2,4-D removal in the system was much lower than that in the electro-Fenton process (68±6 vs. 136±10 kWh/kg TOC). The iron consumption in the system was ~20 times as low as that in the peroxi-coagulation process (196±20 vs. 3940±400 mg/L) within 240 min. The system should be a promising peroxi-coagulation method for organic pollutants removal in wastewater.     

Toward better understanding vacuum ultraviolet–iodide induced photolysis via hydrogen peroxide formation,iodine species change,and difluoroacetic acid degradation

• UV/VUV/I^– induces substantial H₂O₂ and IO₃^– formation, but UV/I^– does not. • Increasing DO level in water enhances H₂O₂ and iodate productions. • Increasing pH decreases H₂O₂ and iodate formation and also photo-oxidation. • The redox potentials of UV/VUV/I^– and UV/VUV changes with pH changes. • The treatability of the UV/VUV/I^– process was stronger than UV/VUV at pH 11.0. Recently, a photochemical process induced by ultraviolet (UV), vacuum UV (VUV), and iodide (I^–) has gained attention for its robust potential for contaminant degradation. However, the mechanisms behind this process remain unclear because both oxidizing and reducing reactants are likely generated. To better understand this process, this study examined the evolutions of hydrogen peroxide (H₂O₂) and iodine species (i.e., iodide, iodate, and triiodide) during the UV/VUV/I^– process under varying pH and dissolved oxygen (DO) conditions. Results show that increasing DO in water enhanced H₂O₂ and iodate production, suggesting that high DO favors the formation of oxidizing species. In contrast, increasing pH (from 6.0 to 11.0) resulted in lower H₂O₂ and iodate formation, indicating that there was a decrease of oxidative capacity for the UV/VUV/I^– process. In addition, difluoroacetic acid (DFAA) was used as an exemplar contaminant to verify above observations. Although its degradation kinetics did not follow a constant trend as pH increases, the relative importance of mineralization appeared declining, suggesting that there was a redox transition from an oxidizing environment to a reducing environment as pH rises. The treatability of the UV/VUV/I^– process was stronger than UV/VUV under pH of 11.0, while UV/VUV process presented a better performance at pH lower than 11.0.     

Effect of current density on groundwater arsenite removal performance using air cathode electrocoagulation

• With the same charge, current density had little effect on As(III) removal in ACEC. • ACEC had the lowest energy consumption compared with EC/O₂ or EC/N₂. • There was a trade-off relationship between energy consumption and removal time. • The ·OH concentration in ACEC was 1.5 times of that in the EC/O₂ system. Naturally occurring arsenic enrichment in groundwater poses a huge threat to human health. Air cathode electrocoagulation (ACEC) has recently been proposed to enhance As(III) oxidation and lower energy consumption. In this study, ACEC, EC/O₂ and EC/N₂ were evaluated with different current densities from 1 to 8 mA/cm² to investigate the effect on As(III) removal in different redox environments. Current density had no appreciable effect on arsenic removal efficiency given the same charge in ACEC because the concentration ratio of Fe/H₂O₂ under different current densities remained stable. However, in EC/O₂ and EC/N₂, As(III) removal was inhibited at higher current densities (4–8 mA/cm²), likely because more Fe(II) competed with As(III) for the oxidant, leading to less effective oxidation of As(III). In all EC systems, the ·OH units generated per power consumption reached the highest value at the lowest current density. Compared with other EC systems, the ACEC system showed lower energy consumption at all current densities due to the low energy consumption of the electrode reaction and more free radical generation. A lower current density saved more energy at the expense of time, showing the trade-off relationship between energy consumption and removal time. The operation costs for As(III) removal under optimal conditions were calculated as 0.028 $/m³ for ACEC, 0.030 $/m³ for EC/O₂, and 0.085 $/m³ for EC/N₂     

Optimization of the O3/H2O2 process with response surface methodology for pretreatment of mother liquor of gas field wastewater

• Real ML-GFW with high salinity and high organics was degraded by O₃/H₂O₂ process. • Successful optimization of operation conditions was attained using RSM based on CCD. • Single-factor experiments in advance ensured optimal experimental conditions. • The satisfactory removal efficiency of TOC was achieved in spite of high salinity. • The initial pH plays the most significant role in the degradation of ML-GFW. The present study reports the use of the O₃/H₂O₂ process in the pretreatment of the mother liquor of gas field wastewater (ML-GFW), obtained from the multi-effect distillation treatment of the gas field wastewater. The range of optimal operation conditions was obtained by single-factor experiments. Response surface methodology (RSM) based on the central composite design (CCD) was used for the optimization procedure. A regression model with Total organic carbon (TOC) removal efficiency as the response value was established (R² = 0.9865). The three key factors were arranged according to their significance as: pH>H₂O₂ dosage>ozone flow rate. The model predicted that the best operation conditions could be obtained at a pH of 10.9, an ozone flow rate of 0.8 L/min, and H₂O₂ dosage of 6.2 mL. The dosing ratio of ozone was calculated to be 9.84 mg O₃/mg TOC. The maximum removal efficiency predicted was 75.9%, while the measured value was 72.3%. The relative deviation was found to be in an acceptable range. The ozone utilization and free radical quenching experiments showed that the addition of H₂O₂ promoted the decomposition of ozone to produce hydroxyl radicals (·OH). This also improved the ozone utilization efficiency. Gas chromatography-mass spectrometry (GC-MS) analysis showed that most of the organic matters in ML-GFW were degraded, while some residuals needed further treatment. This study provided the data and the necessary technical supports for further research on the treatment of ML-GFW.     

Zero-valent manganese nanoparticles coupled with different strong oxidants for thallium removal from wastewater

• Nano zero-valent manganese (nZVMn, Mn⁰) is synthesized via borohydrides reduction. • Mn⁰ combined with persulfate/hypochlorite is effective for Tl removal at pH 6-12. • Mn⁰ can activate persulfate to form hydroxyl and sulfate radicals. • Oxidation-induced precipitation and surface complexation contribute to Tl removal. • Combined Mn⁰-oxidants process is promising in the environmental field. Nano zero-valent manganese (nZVMn, Mn⁰) was prepared through a borohydride reduction method and coupled with different oxidants (persulfate (S₂O₈²⁻), hypochlorite (ClO⁻), or hydrogen peroxide (H₂O₂)) to remove thallium (Tl) from wastewater. The surface of Mn⁰ was readily oxidized to form a core-shell composite (MnO_x@Mn⁰), which consists of Mn⁰ as the inner core and MnO_x (MnO, Mn₂O₃, and Mn₃O₄) as the outer layer. When Mn⁰ was added alone, effective Tl(I) removal was achieved at high pH levels (>12). The Mn⁰-H₂O₂ system was only effective in Tl(I) removal at high pH (>12), while the Mn⁰-S₂O₈²⁻ or Mn⁰-ClO⁻ system had excellent Tl(I) removal (>96%) over a broad pH range (4–12). The Mn⁰-S₂O₈²⁻ oxidation system provided the best resistance to interference from an external organic matrix. The isotherm of Tl(I) removal through the Mn⁰-S₂O₈²⁻ system followed the Freundlich model. The Mn⁰ nanomaterials can activate persulfate to produce sulfate radicals and hydroxyl radicals. Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy suggested that oxidation-induced precipitation, surface adsorption, and electrostatic attraction are the main mechanisms for Tl(I) removal resulting from the combination of Mn⁰ and oxidants. Mn⁰ coupled with S₂O₈²⁻/ClO⁻ is a novel and effective technique for Tl(I) removal, and its application in other fields is worthy of further investigation.     

Enhanced triallyl isocyanurate (TAIC) degradation through application of an O3/UV process: Performance optimization and degradation pathways

• UV/O₃ process had higher TAIC mineralization rate than O₃ process. • Four possible degradation pathways were proposed during TAIC degradation. • pH impacted oxidation processes with pH of 9 achieving maximum efficiency. • CO₃^2– negatively impacted TAIC degradation while HCO₃^– not. • Cl^– can be radicals scavenger only at high concentration (over 500 mg/L Cl^–). Triallyl isocyanurate (TAIC, C₁₂H₁₅N₃O₃) has featured in wastewater treatment as a refractory organic compound due to the significant production capability and negative environmental impact. TAIC degradation was enhanced when an ozone(O₃)/ultraviolet(UV) process was applied compared with the application of an independent O₃ process. Although 99% of TAIC could be degraded in 5 min during both processes, the O₃/UV process had a 70%mineralization rate that was much higher than that of the independent O₃ process (9%) in 30 min. Four possible degradation pathways were proposed based on the organic compounds of intermediate products identified during TAIC degradation through the application of independent O₃ and O₃/UV processes. pH impacted both the direct and indirect oxidation processes. Acidic and alkaline conditions preferred direct and indirect reactions respectively, with a pH of 9 achieving maximum Total Organic Carbon (TOC) removal. Both CO₃^2– and HCO₃^– decreased TOC removal, however only CO₃^2– negatively impacted TAIC degradation. Effects of Cl^– as a radical scavenger became more marked only at high concentrations (over 500 mg/L Cl^–). Particulate and suspended matter could hinder the transmission of ultraviolet light and reduce the production of HO· accordingly.     

Persistent free radicals in humin under redox conditions and their impact in transforming polycyclic aromatic hydrocarbons

• Regulation of redox conditions promotes the generation of free radicals on HM. • HM-PFRs can be fractionated into active and inactive types depending on stability. • The newly produced PFRs readily release electrons to oxygen and generate ROS. • PFR-induced ROS mediate the transformation of organic contaminants adsorbed on HM. The role of humic substance-associated persistent free radicals (PFRs) in the fate of organic contaminants under various redox conditions remains unknown. This study examined the characterization of original metal-free peat humin (HM), and HM treated with varying concentrations of H₂O₂ and L-ascorbic acid (VC) (assigned as H₂O₂-HM and VC-HM). The concentration of PFRs in HM increased with the addition of VC/H₂O₂ at concentrations less than 0.08 M. The evolution of PFRs in HM under different environmental conditions (e.g., oxic/anoxic and humidity) was investigated. Two types of PFRs were detected in HM: a relatively stable radical existed in the original sample, and the other type, which was generated by redox treatments, was relatively unstable. The spin densities of VC/H₂O₂-HM readily returned to the original value under relatively high humidity and oxic conditions. During this process, the HM-associated “unstable” free radicals released an electron to O₂, inducing the formation of reactive oxygen species (ROS, i.e., ^•OH and ^•O₂⁻). The generated ROS promoted the degradation of polycyclic aromatic hydrocarbons based on the radical quenching measurements. The transformation rates followed the order naphthalene>phenanthrene>anthracene>benzo[a]pyrene. Our results provide valuable insight into the HM-induced transformation of organic contaminants under natural conditions.     

Experimental and computational assessment of 1,4-Dioxane degradation in a photo-Fenton reactive ceramic membrane filtration process

• 1,4-Dioxane was degraded via the photo-Fenton reactive membrane filtration. • Degradation efficiency and AQY were both enhanced in photocatalytic membrane. • There is a tradeoff between photocatalytic degradation and membrane permeation flux. • Degradation pathways of 1,4-Dioxane is revealed by DFT analysis. The present study evaluated a photo-Fenton reactive membrane that achieved enhanced 1,4-Dioxane removal performance. As a common organic solvent and stabilizer, 1,4-Dioxane is widely used in a variety of industrial products and poses negative environmental and health impacts. The membrane was prepared by covalently coating photocatalyst of goethite (α-FeOOH) on a ceramic porous membrane as we reported previously. The effects of UV irradiation, H₂O₂ and catalyst on the removal efficiency of 1,4-Dioxane in batch reactors were first evaluated for optimized reaction conditions, followed by a systematical investigation of 1,4-Dioxane removal in the photo-Fenton membrane filtration mode. Under optimized conditions, the 1,4-Dioxane removal rate reached up to 16% with combination of 2 mmol/L H₂O₂ and UV₃₆₅ irradiation (2000 µW/cm²) when the feed water was filtered by the photo-Fenton reactive membrane at a hydraulic retention time of 6 min. The removal efficiency and apparent quantum yield (AQY) were both enhanced in the filtration compared to the batch mode of the same photo-Fenton reaction. Moreover, the proposed degradation pathways were analyzed by density functional theory (DFT) calculations, which provided a new insight into the degradation mechanisms of 1,4-Dioxane in photo-Fenton reactions on the functionalized ceramic membrane.     

Degradation of refractory organics in concentrated leachate by the Fenton process: Central composite design for process optimization

• 90% total COD, 95.3% inert COD and 97.2% UV₂₅₄ were removed. • High R² values (over 95%) for all responses were obtained with CCD. • Operational cost was calculated to be 0.238 €/g COD_removed for total COD removal. • Fenton oxidation was highly-efficient method for inert COD removal. • BOD₅/COD ratio of leachate concentrate raised from 0.04 to 0.4. The primary aim of this study is inert COD removal from leachate nanofiltration concentrate because of its high concentration of resistant organic pollutants. Within this framework, this study focuses on the treatability of leachate nanofiltration concentrate through Fenton oxidation and optimization of process parameters to reach the maximum pollutant removal by using response surface methodology (RSM). Initial pH, Fe²⁺ concentration, H₂O₂/Fe²⁺ molar ratio and oxidation time are selected as the independent variables, whereas total COD, color, inert COD and UV₂₅₄ removal are selected as the responses. According to the ANOVA results, the R² values of all responses are found to be over 95%. Under the optimum conditions determined by the model (pH: 3.99, Fe²⁺: 150 mmol/L, H₂O₂/Fe²⁺: 3.27 and oxidation time: 84.8 min), the maximum COD removal efficiency is determined as 91.4% by the model. The color, inert COD and UV₂₅₄ removal efficiencies are determined to be 99.9%, 97.2% and 99.5%, respectively, by the model, whereas the total COD, color, inert COD and UV₂₅₄ removal efficiencies are found respectively to be 90%, 96.5%, 95.3% and 97.2%, experimentally under the optimum operating conditions. The Fenton process improves the biodegradability of the leachate NF concentrate, increasing the BOD₅/COD ratio from the value of 0.04 to the value of 0.4. The operational cost of the process is calculated to be 0.238 €/g COD_removed. The results indicate that the Fenton oxidation process is an efficient and economical technology in improvement of the biological degradability of leachate nanofiltration concentrate and in removal of resistant organic pollutants.     

Electro-catalytic activity of CeOx modified graphite felt for carbamazepine degradation via E-peroxone process

•CeO_x/GF-EP process had the better degradation efficiency than GF-EP process. •CeO_x/GF-EP process had the flexible application in the pH range from 5.0 to 9.0. •CeO_x could enhance surface hydrophilicity and reduce the charge-transfer resistance. •The interfacial electron transfer process was revealed. E-peroxone (EP) was one of the most attractive AOPs for removing refractory organic compounds from water, but the high energy consumption for in situ generating H₂O₂ and its low reaction efficiency for activating O₃ under acidic conditions made the obstacles for its practical application. In this study, cerium oxide was loaded on the surface of graphite felt (GF) by the hydrothermal method to construct the efficient electrode (CeO_x/GF) for mineralizing carbamazepine (CBZ) via EP process. CeO_x/GF was an efficient cathode, which led to 69.4% TOC removal in CeO_x/GF-EP process with current intensity of 10 mA in 60 min. Moreover, CeO_x/GF had the flexible application in the pH range from 5.0 to 9.0, TOC removal had no obvious decline with decrease of pH. Comparative characterizations showed that CeO_x could enhance surface hydrophilicity and reduce the charge-transfer resistance of GF. About 5.4 mg/L H₂O₂ generated in CeO_x/GF-EP process, which was 2.1 times as that in GF-EP process. The greater ozone utility was also found in CeO_x/GF-EP process. More O₃ was activated into hydroxyl radicals, which accounted for the mineralization of CBZ. An interfacial electron transfer process was revealed, which involved the function of oxygen vacancies and Ce³⁺/Ce⁴⁺ redox cycle. CeO_x/GF had the good recycling property in fifth times’ use.     

Enhanced catalytic oxidation of 2,4-dichlorophenol via singlet oxygen dominated peroxymonosulfate activation on CoOOH@Bi2O3 composite

• Bi₂O₃ cannot directly activate PMS. • Bi₂O₃ loading increased the specific surface area and conductivity of CoOOH. • Larger specific surface area provided more active sites for PMS activation. • Faster electron transfer rate promoted the generation of reactive oxygen species. • ¹O₂ was identified as dominant ROS in the CoOOH@Bi₂O₃/PMS system. Cobalt oxyhydroxide (CoOOH) has been turned out to be a high-efficiency catalyst for peroxymonosulfate (PMS) activation. In this study, CoOOH was loaded on bismuth oxide (Bi₂O₃) using a facile chemical precipitation process to improve its catalytic activity and stability. The result showed that the catalytic performance on the 2,4-dichlorophenol (2,4-DCP) degradation was significantly enhanced with only 11 wt% Bi₂O₃ loading. The degradation rate in the CoOOH@Bi₂O₃/PMS system (0.2011 min⁻¹) was nearly 6.0 times higher than that in the CoOOH/PMS system (0.0337 min⁻¹). Furthermore, CoOOH@Bi₂O₃ displayed better stability with less Co ions leaching (16.4% lower than CoOOH) in the PMS system. These phenomena were attributed to the Bi₂O₃ loading which significantly increased the conductivity and specific surface area of the CoOOH@Bi₂O₃ composite. Faster electron transfer facilitated the redox reaction of Co (III) / Co (II) and thus was more favorable for reactive oxygen species (ROS) generation. Meanwhile, larger specific surface area furnished more active sites for PMS activation. More importantly, there were both non-radical (¹O₂) and radicals (SO₄⁻•, O₂⁻•, and OH•) in the CoOOH@Bi₂O₃/PMS system and ¹O₂ was the dominant one. In general, this study provided a simple and practical strategy to enhance the catalytic activity and stability of cobalt oxyhydroxide in the PMS system.     

The treatment of black-odorous water using tower bipolar electro-flocculation including the removal of phosphorus,turbidity, sulfion,and oxygen enrichment

• An innovative bubble column tower BPE was designed to treat the black-odorous water. • PO₄³⁻, S²⁻ and turbidity were removed, and dissolved oxygen was enriched in the BPE. • An aluminum bipolar electrode gave the best oxygen enrichment and pollutant removal. • Changes of microorganisms confirmed the improvement in water quality achieved. The large amount of municipal wastewater discharged into urban rivers sometimes exceeds the rivers’ self-purification capacity leading to black-odorous polluted water. Electro-flocculation has emerged as a powerful remediation technology. Electro-flocculation in a bubble column tower with a bipolar electrode (BPE) was tested in an attempt to overcome the high resistance and weak gas-floatation observed with a monopolar electrode (MPE) in treating such water. The BPE reactor tested had a Ti/Ta₂O₅-IrO₂ anode and a graphite cathode with an iron or aluminum bipolar electrode suspended between them. It was tested for its ability to reduce turbidity, phosphate and sulphion and to increase the concentration of dissolved oxygen. The inclusion of the bipolar electrode was found to distinctly improved the system’s conductivity. The system’s electro-flocculation and electrical floatation removed turbidity, phosphate and sulphion completely, and the dissolved oxygen level improved from 0.29 to 6.28 mg/L. An aluminum bipolar electrode performed better than an iron one. Changes in the structure of the microbial community confirmed a significant improvement in water quality.     

One-step ball milling-prepared nano Fe2O3 and nitrogen-doped graphene with high oxygen reduction activity and its application in microbial fuel cells

• Nano Fe₂O₃ and N-doped graphene was prepared via a one-step ball milling method. • The maximum power density of Fe-N-G in MFC was 390% of that of pristine graphite. • Active sites like nano Fe₂O₃, pyridinic N and Fe-N groups were formed in Fe-N-G. • The improvement of Fe-N-G was due to full exposure of active sites on graphene. Developing high activity, low-cost and long durability catalysts for oxygen reduction reaction is of great significance for the practical application of microbial fuel cells. The full exposure of active sites in catalysts can enhance catalytic activity dramatically. Here, novel Fe-N-doped graphene is successfully synthesized via a one-step in situ ball milling method. Pristine graphite, ball milling graphene, N-doped graphene and Fe-N-doped graphene are applied in air cathodes, and enhanced performance is observed in microbial fuel cells with graphene-based catalysts. Particularly, Fe-N-doped graphene achieves the highest oxygen reduction reaction activity, with a maximum power density of 1380±20 mW/m² in microbial fuel cells and a current density of 23.8 A/m² at –0.16 V in electrochemical tests, which are comparable to commercial Pt and 390% and 640% of those of pristine graphite. An investigation of the material characteristics reveals that the superior performance of Fe-N-doped graphene results from the full exposure of Fe₂O₃ nanoparticles, pyrrolic N, pyridinic N and excellent Fe-N-G active sites on the graphene matrix. This work not only suggests the strategy of maximally exposing active sites to optimize the potential of catalysts but also provides promising catalysts for the use of microbial fuel cells in sustainable energy generation.     

Hydroxyl radical intensified Cu2O NPs/H2O2 process in ceramic membrane reactor for degradation on DMAc wastewater from polymeric membrane manufacturer

• Cu₂O NPs/H₂O₂ Fenton process was intensified by membrane dispersion. • DMAc removal was enhanced to 98% for initial DMAc of 14000 mg/L. • Analyzed time-resolved degradation pathway of DMAc under ·OH attack. High-concentration industrial wastewater containing N,N-dimethylacetamide (DMAc) from polymeric membrane manufacturer was degraded in Cu₂O NPs/H₂O₂ Fenton process. In the membrane-assisted Fenton process DMAc removal rate was up to 98% with 120 min which was increased by 23% over the batch reactor. It was found that ·OH quench time was extended by 20 min and the maximum ·OH productivity was notably 88.7% higher at 40 min. The degradation reaction rate constant was enhanced by 2.2 times with membrane dispersion (k = 0.0349 min⁻¹). DMAc initial concentration (C₀) and H₂O₂ flux (J_p) had major influence on mass transfer and kinetics, meanwhile, membrane pore size (r_p) and length (L_m) also affected the reaction rate. The intensified radical yield, fast mass transfer and nanoparticles high activity all contributed to improve pollutant degradation efficiency. Time-resolved DMAc degradation pathway was analyzed as hydroxylation, demethylation and oxidation leading to the final products of CO₂, H₂O and NO₃⁻ (rather than NH₃ from biodegradation). Continuous process was operated in the dual-membrane configuration with in situ reaction and separation. After five cycling tests, DMAc removal was all above 95% for the initial [DMAc]₀ = 14,000 mg/L in wastewater and stability of the catalyst and the membrane maintained well.     

One-pot hydrothermal fabrication of BiVO4/Fe3O4/rGO composite photocatalyst for the simulated solar light-driven degradation of Rhodamine B

• BiVO₄/Fe₃O₄/rGO has excellent photocatalytic activity under solar light radiation. • It can be easily separated and collected from water in an external magnetic field. • BiVO₄/Fe₃O₄/0.5% rGO exhibited the highest RhB removal efficiency of over 99%. • Hole (h⁺) and superoxide radical (O₂^•−) dominate RhB photo-decomposition process. • The reusability of this composite was confirmed by five successive recycling runs. Fabrication of easily recyclable photocatalyst with excellent photocatalytic activity for degradation of organic pollutants in wastewater is highly desirable for practical application. In this study, a novel ternary magnetic photocatalyst BiVO₄/Fe₃O₄/reduced graphene oxide (BiVO₄/Fe₃O₄/rGO) was synthesized via a facile hydrothermal strategy. The BiVO₄/Fe₃O₄ with 0.5 wt% of rGO (BiVO₄/Fe₃O₄/0.5% rGO) exhibited superior activity, degrading greater than 99% Rhodamine B (RhB) after 120 min solar light radiation. The surface morphology and chemical composition of BiVO₄/Fe₃O₄/rGO were studied by scanning electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, UV–visible diffuse reflectance spectroscopy, Fourier transform infrared spectroscopy, and Raman spectroscopy. The free radicals scavenging experiments demonstrated that hole (h⁺) and superoxide radical (O₂^•−) were the dominant species for RhB degradation over BiVO₄/Fe₃O₄/rGO under solar light. The reusability of this composite catalyst was also investigated after five successive runs under an external magnetic field. The BiVO₄/Fe₃O₄/rGO composite was easily separated, and the recycled catalyst retained high photocatalytic activity. This study demonstrates that catalyst BiVO₄/Fe₃O₄/rGO possessed high dye removal efficiency in water treatment with excellent recyclability from water after use. The current study provides a possibility for more practical and sustainable photocatalytic process.     

Characterization of electrode fouling during electrochemical oxidation of phenolic pollutant

• Electrode fouling is characterized by non-destructive characterization. • Electrode fouling is highly dependent on electrochemical process. • Active chlorine can prevent the formation of polymeric fouling film. Electrode fouling is a problem that commonly occurs during electro-oxidation water purification. This study focused on identifying the fouling behavior of Pt electrode associated with the formation of polymeric layer during electro-oxidation of phenol. The in situ electrochemical measurements and non-destructive observation of the electrode morphology were reported. The results demonstrated that the electrode fouling was highly dependent on thermodynamic process of electrode that was controlled by anode potential. At anode potential lower than 1.0 V vs SHE, the direct electro-oxidation caused the electrode fouling by the formation of polymeric film. The fouling layer decreased the electrochemically active surface area from 8.38 cm² to 1.57 cm², indicated by the formation of polymeric film with thickness of 2.3 mm, increase in mass growing at a rate of 3.26 μg/cm²/min. The degree to which the anode was fouled was independent of anion in the electrolyte. In comparison, at anode potential higher than 2.7 V vs SHE, the anions (e.g., chloride) could exert a major influence to the behavior of electrode fouling. The presence of chloride was shown to mitigate the fouling of electrode significantly through preventing the formation of polymeric film by active chlorine (e.g., Cl• and Cl₂) produced from anodic oxidation of chloride. Since chloride is the most abundant anionic species existing in both natural and engineered water system, this study not only offers a deep insight into the mechanism of electrode fouling, but also suggests strategies for anti-fouling in the presence of chloride in electro-oxidation process.     

Simultaneous removal of NOx and chlorobenzene on V2O5/TiO2 granular catalyst: Kinetic study and performance prediction

• A V₂O₅/TiO₂ granular catalyst for simultaneous removal of NO and chlorobenzene. • Catalyst synthesized by vanadyl acetylacetonate showed good activity and stability. • The kinetic model was established and the synergetic activity was predicted. • Both chlorobenzene oxidation and SCR of NO follow pseudo-first-order kinetics. • The work is of much value to design of multi-pollutants emission control system. The synergetic abatement of multi-pollutants is one of the development trends of flue gas pollution control technology, which is still in the initial stage and facing many challenges. We developed a V₂O₅/TiO₂ granular catalyst and established the kinetic model for the simultaneous removal of NO and chlorobenzene (i.e., an important precursor of dioxins). The granular catalyst synthesized using vanadyl acetylacetonate precursor showed good synergistic catalytic performance and stability. Although the SCR reaction of NO and the oxidation reaction of chlorobenzene mutually inhibited, the reaction order of each reaction was not considerably affected, and the pseudo-first-order reaction kinetics was still followed. The performance prediction of this work is of much value to the understanding and reasonable design of a catalytic system for multi-pollutants (i.e., NO and dioxins) emission control.     

Size and shape effects of MnFe2O4 nanoparticles as catalysts for reductive degradation of dye pollutants

• Size and shape-dependent MnFe₂O₄ NPs were prepared via a facile method. • Ligand-exchange chemistry was used to prepare the hydrophilic MnFe₂O₄ NPs. • The catalytic properties of MnFe₂O₄ NPs toward dye degradation were fully studied. • The catalytic activities of MnFe₂O₄ NPs followed Michaelis–Menten behavior. • All the MnFe₂O₄ NPs exhibit selective degradation to different dyes. The magnetic nanoparticles that are easy to recycle have tremendous potential as a suitable catalyst for environmental toxic dye pollutant degradation. Rationally engineering shapes and tailoring the size of nanocatalysts are regarded as an effective manner for enhancing performances. Herein, we successfully synthesized three kinds of MnFe₂O₄ NPs with distinctive sizes and shapes as catalysts for reductive degradation of methylene blue, rhodamine 6G, rhodamine B, and methylene orange. It was found that the catalytic activities were dependent on the size and shape of the MnFe₂O₄ NPs and highly related to the surface-to-volume ratio and atom arrangements. Besides, all these nanocatalysts exhibit selectivity to different organic dyes, which is beneficial for their practical application in dye pollutant treatment. Furthermore, the MnFe₂O₄ NPs could be readily recovered by a magnet and reused more than ten times without appreciable loss of activity. The size and shape effects of MnFe₂O₄ nanoparticles demonstrated in this work not only accelerate further understanding the nature of nanocatalysts but also contribute to the precise design of nanoparticles catalyst for pollutant degradation.     

A novel approach to preparing ultra-lightweight ceramsite with a large amount of fly ash

•Ultra-lightweight ceramsite is prepared with 80% fly ash. •SiO₂, Al₂O₃, and flux contents significantly influence the performance of ceramsite. •The expansion of ceramsite is caused by the formation of a dense glaze and gas. •The bulk density of ultra-lightweight ceramsite is only 340 kg/m³. The disposal of fly ash has become a serious problem in China due to its rapid increase in volume in recent years. The most common method of fly ash disposal is solidification-stabilization-landfill, and the most common reuse is low-value-added building materials. A novel processing method for preparing ultra-lightweight ceramsite with fly ash was developed. The results show that the optimal parameters for preparation of ultra-lightweight ceramsite are as follows: mass ratio of fly ash:kaolin:diatomite= 80:15:5, preheating temperature of 800°C, preheating time of 5 min, sintering temperature of 1220°C, and sintering time of 10 min. The expansion agent is perlite, at 10 wt.% addition. Finally, a ceramsite with bulk density of 340 kg/m³, particle density of 0.68 g/cm³, and cylinder compressive strength of 1.02 MPa was obtained. Because of its low density and high porosity, ultra-lightweight ceramsite has excellent thermal insulation performance, and its strength is generally low, so it is usually used in the production of thermal insulation concrete and its products. The formation of a liquid-phase component on the surface, and generation of a gas phase inside ceramsite during the sintering process, make it possible to control the production of the suitable liquid phase and gas in this system, resulting in an optimization of the expansion behavior and microstructure of ceramsite. These characteristics show the feasibility of industrial applications of fly ash for the production of ultra-lightweight ceramsite, which could not only produce economic benefits, but also conserve land resources and protect the environment.     

Enhancement of the electrocatalytic oxidation of antibiotic wastewater over the conductive black carbon-PbO2 electrode prepared using novel green approach

• A novel conductive carbon black modified lead dioxide electrode is synthesized. • The modified PbO₂ electrode exhibits enhanced electrochemical performances. • BBD method could predict optimal experiment conditions accurately and reliably. • The modified electrode possesses outstanding reusability and safety. The secondary pollution caused by modification of an electrode due to doping of harmful materials has long been a big concern. In this study, an environmentally friendly material, conductive carbon black, was adopted for modification of lead dioxide electrode (PbO₂). It was observed that the as-prepared conductive carbon black modified electrode (C-PbO₂) exhibited an enhanced electrocatalytical performance and more stable structure than a pristine PbO₂ electrode, and the removal efficiency of metronidazole (MNZ) and COD by a 1.0% C-PbO₂ electrode at optimal conditions was increased by 24.66% and 7.01%, respectively. Results revealed that the electrochemical degradation of MNZ wastewater followed pseudo-first-order kinetics. This intimates that the presence of conductive carbon black could improve the current efficiency, promote the generation of hydroxyl radicals, and accelerate the removal of MNZ through oxidation. In addition, MNZ degradation pathways through a C-PbO₂ electrode were proposed based on the identified intermediates. To promote the electrode to treat antibiotic wastewater, optimal experimental conditions were predicted through the Box-Behnken design (BBD) method. The results of this study suggest that a C-PbO₂ electrode may represent a promising functional material to pretreat antibiotic wastewaters.