Co-present Pb(II) accelerates the oxidation of organic contaminants by permanganate: Role of Pb(III)

• Simultaneous removal of organic contaminants and Pb(II) was achieved by Mn(VII). • Pb(II) enhanced Mn(VII) oxidation performance over a wide pH range. • Pb(II) did not alter the pH-rate profile for contaminants oxidation by Mn(VII). • Mn(VII) alone cannot oxidize Pb(II) effectively at pH below 5.0. • Pb(III) plays important roles on enhancing Mn(VII) decontamination process. The permanganate (Mn(VII)) oxidation has emerged as a promising technology for the remediation and treatment of the groundwater and surface water contaminated with the organic compounds. Nonetheless, only a few studies have been conducted to explore the role of the heavy metals (especially the redox-active ones) during the Mn(VII) oxidation process. In this study, taking Pb(II) as an example, its influence on the Mn(VII) decontamination performance has been extensively investigated. It was found that, with the presence of Pb(II), Mn(VII) could degrade diclofenac (DCF), 2,4-dichlorophenol, and aniline more effectively than without. For instance, over a wide pH range of 4.5–8.0, the dosing of 10 μmol/L Pb(II) accelerated the DCF removal rate from 0.006–0.25 min⁻¹ to 0.05–0.46 min⁻¹ with a promotion factor of 1.9–9.4. Although the UV-vis spectroscopic and high resolution transmission electron microscopy analyses suggested that Mn(VII) could react with Pb(II) to produce Mn(IV) and Pb(IV) at pH 6.0–8.0, further experiments revealed that Pb(II) did not exert its enhancing effect through promoting the generation of MnO₂, as the reactivity of MnO₂ was poor under the employed pH range. At pH below 5.0, it was interesting to find that, a negligible amount of MnO₂ was formed in the Mn(VII)/Pb(II) system in the absence of contaminants, while once MnO₂ was generated in the presence of contaminants, it could catalyze the Pb(II) oxidation to Pb(IV) by Mn(VII). Collectively, by highlighting the conversion process of Pb(II) to Pb(IV) by either Mn(VII) or MnO₂, the reactive Pb(III) intermediates were proposed to account for the Pb(II) enhancement effect.     

TiO2@palygorskite composite for the efficient remediation of oil spills via a dispersion-photodegradation synergy

• A novel and multi-functional clay-based oil spill remediation system was constructed. • TiO₂@PAL functions as a particulate dispersant to break oil slick into tiny droplets. • Effective dispersion leads to the direct contact of TiO₂ with oil pollutes directly. • TiO₂ loaded on PAL exhibits efficient photodegradation for oil pollutants. • TiO₂@PAL shows a typical dispersion-photocatalysis synergistic remediation. Removing spilled oil from the water surface is critically important given that oil spill accidents are a common occurrence. In this study, TiO₂@Palygorskite composite prepared by a simple coprecipitation method was used for oil spill remediation via a dispersion-photodegradation synergy. Diesel could be efficiently dispersed into small oil droplets by TiO₂@Palygorskite. These dispersed droplets had an average diameter of 20–30 mm and exhibited good time stability. The tight adsorption of TiO₂@Palygorskite on the surface of the droplets was observed in fluorescence and SEM images. As a particulate dispersant, the direct contact of TiO₂@Palygorskite with oil pollutants effectively enhanced the photodegradation efficiency of TiO₂ for oil. During the photodegradation process, •O₂⁻and •OH were detected by ESR and radical trapping experiments. The photodegradation efficiency of diesel by TiO₂@Palygorskite was enhanced by about 5 times compared with pure TiO₂ under simulated sunlight irradiation. The establishment of this new dispersion-photodegradation synergistic remediation system provides a new direction for the development of marine oil spill remediation.     

Enhanced catalytic oxidation of 2,4-dichlorophenol via singlet oxygen dominated peroxymonosulfate activation on CoOOH@Bi2O3 composite

• Bi₂O₃ cannot directly activate PMS. • Bi₂O₃ loading increased the specific surface area and conductivity of CoOOH. • Larger specific surface area provided more active sites for PMS activation. • Faster electron transfer rate promoted the generation of reactive oxygen species. • ¹O₂ was identified as dominant ROS in the CoOOH@Bi₂O₃/PMS system. Cobalt oxyhydroxide (CoOOH) has been turned out to be a high-efficiency catalyst for peroxymonosulfate (PMS) activation. In this study, CoOOH was loaded on bismuth oxide (Bi₂O₃) using a facile chemical precipitation process to improve its catalytic activity and stability. The result showed that the catalytic performance on the 2,4-dichlorophenol (2,4-DCP) degradation was significantly enhanced with only 11 wt% Bi₂O₃ loading. The degradation rate in the CoOOH@Bi₂O₃/PMS system (0.2011 min⁻¹) was nearly 6.0 times higher than that in the CoOOH/PMS system (0.0337 min⁻¹). Furthermore, CoOOH@Bi₂O₃ displayed better stability with less Co ions leaching (16.4% lower than CoOOH) in the PMS system. These phenomena were attributed to the Bi₂O₃ loading which significantly increased the conductivity and specific surface area of the CoOOH@Bi₂O₃ composite. Faster electron transfer facilitated the redox reaction of Co (III) / Co (II) and thus was more favorable for reactive oxygen species (ROS) generation. Meanwhile, larger specific surface area furnished more active sites for PMS activation. More importantly, there were both non-radical (¹O₂) and radicals (SO₄⁻•, O₂⁻•, and OH•) in the CoOOH@Bi₂O₃/PMS system and ¹O₂ was the dominant one. In general, this study provided a simple and practical strategy to enhance the catalytic activity and stability of cobalt oxyhydroxide in the PMS system.     

Enhanced triallyl isocyanurate (TAIC) degradation through application of an O3/UV process: Performance optimization and degradation pathways

• UV/O₃ process had higher TAIC mineralization rate than O₃ process. • Four possible degradation pathways were proposed during TAIC degradation. • pH impacted oxidation processes with pH of 9 achieving maximum efficiency. • CO₃^2– negatively impacted TAIC degradation while HCO₃^– not. • Cl^– can be radicals scavenger only at high concentration (over 500 mg/L Cl^–). Triallyl isocyanurate (TAIC, C₁₂H₁₅N₃O₃) has featured in wastewater treatment as a refractory organic compound due to the significant production capability and negative environmental impact. TAIC degradation was enhanced when an ozone(O₃)/ultraviolet(UV) process was applied compared with the application of an independent O₃ process. Although 99% of TAIC could be degraded in 5 min during both processes, the O₃/UV process had a 70%mineralization rate that was much higher than that of the independent O₃ process (9%) in 30 min. Four possible degradation pathways were proposed based on the organic compounds of intermediate products identified during TAIC degradation through the application of independent O₃ and O₃/UV processes. pH impacted both the direct and indirect oxidation processes. Acidic and alkaline conditions preferred direct and indirect reactions respectively, with a pH of 9 achieving maximum Total Organic Carbon (TOC) removal. Both CO₃^2– and HCO₃^– decreased TOC removal, however only CO₃^2– negatively impacted TAIC degradation. Effects of Cl^– as a radical scavenger became more marked only at high concentrations (over 500 mg/L Cl^–). Particulate and suspended matter could hinder the transmission of ultraviolet light and reduce the production of HO· accordingly.     

Enhanced carbon tetrachloride degradation by hydroxylamine in ferrous ion activated calcium peroxide in the presence of formic acid

• Complete CT degradation was achieved by employing HA to CP/Fe(II)/FA process. • Quantitative detection of Fe(II) regeneration and HO• production was investigated. • Benzoic acid outcompeted FA for the reaction with HO•. • CO₂•⁻ was the dominant reductive radical for CT removal. • Effects of solution matrix on CT removal were conducted. Hydroxyl radicals (HO•) show low reactivity with perchlorinated hydrocarbons, such as carbon tetrachloride (CT), in conventional Fenton reactions, therefore, the generation of reductive radicals has attracted increasing attention. This study investigated the enhancement of CT degradation by the synergistic effects of hydroxylamine (HA) and formic acid (FA) (initial [CT] = 0.13 mmol/L) in a Fe(II) activated calcium peroxide (CP) Fenton process. CT degradation increased from 56.6% to 99.9% with the addition of 0.78 mmol/L HA to the CP/Fe(II)/FA/CT process in a molar ratio of 12/6/12/1. The results also showed that the presence of HA enhanced the regeneration of Fe(II) from Fe(III), and the production of HO• increased one-fold when employing benzoic acid as the HO• probe. Additionally, FA slightly improves the production of HO•. A study of the mechanism confirmed that the carbon dioxide radical (CO₂•⁻), a strong reductant generated by the reaction between FA and HO•, was the dominant radical responsible for CT degradation. Almost complete CT dechlorination was achieved in the process. The presence of humic acid and chloride ion slightly decreased CT removal, while high doses of bicarbonate and high pH inhibited CT degradation. This study helps us to better understand the synergistic roles of FA and HA for HO• and CO₂•⁻ generation and the removal of perchlorinated hydrocarbons in modified Fenton systems.     

Size and shape effects of MnFe2O4 nanoparticles as catalysts for reductive degradation of dye pollutants

• Size and shape-dependent MnFe₂O₄ NPs were prepared via a facile method. • Ligand-exchange chemistry was used to prepare the hydrophilic MnFe₂O₄ NPs. • The catalytic properties of MnFe₂O₄ NPs toward dye degradation were fully studied. • The catalytic activities of MnFe₂O₄ NPs followed Michaelis–Menten behavior. • All the MnFe₂O₄ NPs exhibit selective degradation to different dyes. The magnetic nanoparticles that are easy to recycle have tremendous potential as a suitable catalyst for environmental toxic dye pollutant degradation. Rationally engineering shapes and tailoring the size of nanocatalysts are regarded as an effective manner for enhancing performances. Herein, we successfully synthesized three kinds of MnFe₂O₄ NPs with distinctive sizes and shapes as catalysts for reductive degradation of methylene blue, rhodamine 6G, rhodamine B, and methylene orange. It was found that the catalytic activities were dependent on the size and shape of the MnFe₂O₄ NPs and highly related to the surface-to-volume ratio and atom arrangements. Besides, all these nanocatalysts exhibit selectivity to different organic dyes, which is beneficial for their practical application in dye pollutant treatment. Furthermore, the MnFe₂O₄ NPs could be readily recovered by a magnet and reused more than ten times without appreciable loss of activity. The size and shape effects of MnFe₂O₄ nanoparticles demonstrated in this work not only accelerate further understanding the nature of nanocatalysts but also contribute to the precise design of nanoparticles catalyst for pollutant degradation.     

Toward better understanding vacuum ultraviolet–iodide induced photolysis via hydrogen peroxide formation,iodine species change,and difluoroacetic acid degradation

• UV/VUV/I^– induces substantial H₂O₂ and IO₃^– formation, but UV/I^– does not. • Increasing DO level in water enhances H₂O₂ and iodate productions. • Increasing pH decreases H₂O₂ and iodate formation and also photo-oxidation. • The redox potentials of UV/VUV/I^– and UV/VUV changes with pH changes. • The treatability of the UV/VUV/I^– process was stronger than UV/VUV at pH 11.0. Recently, a photochemical process induced by ultraviolet (UV), vacuum UV (VUV), and iodide (I^–) has gained attention for its robust potential for contaminant degradation. However, the mechanisms behind this process remain unclear because both oxidizing and reducing reactants are likely generated. To better understand this process, this study examined the evolutions of hydrogen peroxide (H₂O₂) and iodine species (i.e., iodide, iodate, and triiodide) during the UV/VUV/I^– process under varying pH and dissolved oxygen (DO) conditions. Results show that increasing DO in water enhanced H₂O₂ and iodate production, suggesting that high DO favors the formation of oxidizing species. In contrast, increasing pH (from 6.0 to 11.0) resulted in lower H₂O₂ and iodate formation, indicating that there was a decrease of oxidative capacity for the UV/VUV/I^– process. In addition, difluoroacetic acid (DFAA) was used as an exemplar contaminant to verify above observations. Although its degradation kinetics did not follow a constant trend as pH increases, the relative importance of mineralization appeared declining, suggesting that there was a redox transition from an oxidizing environment to a reducing environment as pH rises. The treatability of the UV/VUV/I^– process was stronger than UV/VUV under pH of 11.0, while UV/VUV process presented a better performance at pH lower than 11.0.     

UV-LED/P25-based photocatalysis for effective degradation of isothiazolone biocide

• UV-LED with shorter wavelength was beneficial for photocatalytic degradation. • SRNOM dramatically inhibit the degradation. • ·OH acts as the active radical in photocatalytic degradation. • Degradation mainly undergoes oxidation, hydrolysis and chain growth reactions. In this work, LED-based photocatalysis using mixed rutile and anatase phase TiO₂ (P25) as the photocatalyst could effectively remove 5-chloro-2-methyl-4-isothiazolin-3-one (CMIT) and methylisothiazolone (MIT) simultaneously, with removal efficiencies above 80% within 20 min. The photocatalytic degradation of both CMIT and MIT could be modeled using a pseudo-first-order rate equation. The photocatalytic degradation rates of CMIT and MIT under LED280 illumination were higher than under LED310 or LED360 illumination. At concentrations below 100 mg/L, the degradation rate of CMIT and MIT under LED illumination significantly increased with increasing catalyst dosage. Additionally, the effects of the chloride ion concentration, alkalinity and dissolved organic matter on the photocatalytic degradation reaction were also investigated. The ·OH free radicals were determined to play the primary role in the photocatalytic degradation reaction, with a degradation contribution of >95%. The photocatalytic degradation of CMIT and MIT mainly occurred via oxidation, hydrolysis, and chain growth reactions. Finally, the possible photocatalytic degradation pathways of CMIT and MIT over LED/P25 are proposed.     

Enhanced enzymatic removal of anthracene by the mangrove soil-derived fungus, Aspergillus sydowii BPOI

• A. sydowii strain bpo1 exhibited 99.8% anthracene degradation efficiency. • Four unique metabolic products were obtained after anthracene degradation. • Ligninolytic enzymes induction played vital roles in the removal of anthracene. • Laccase played a crucial role in comparison with other enzymes induced. The present study investigated the efficiency of Aspergillus sydowii strain bpo1 (GenBank Accession Number: MK373021) in the removal of anthracene (100 mg/L). Optimal degradation efficiency (98.7%) was observed at neutral pH, temperature (30℃), biomass weight (2 g) and salinity (0.2% w/v) within 72 h. The enzyme analyses revealed 131%, 107%, and 89% induction in laccase, lignin peroxidase, and manganese peroxidase respectively during anthracene degradation. Furthermore, the degradation efficiency (99.8%) and enzyme induction were significantly enhanced with the addition of 100 mg/L of citric acid and glucose to the culture. At varying anthracene concentrations (100–500 mg/L), the degradation rate constants (k₁) peaked with increasing concentration of anthracene while the half-life (t_1/2) decreases with increase in anthracene concentration. Goodness of fit (R² = 0.976 and 0.982) was observed when the experimental data were subjected to Langmuir and Temkin models respectively which affirmed the monolayer and heterogeneous nature exhibited by A. sydwoii cells during degradation. Four distinct metabolites; anthracene-1,8,9 (2H,8aH,9aH)-trione, 2,4a-dihydronaphthalene-1,5-dione, 1,3,3a,7a-tetrahydro-2-benzofuran-4,7-dione and 2-hydroxybenzoic acid was obtained through Gas Chromatography-Mass spectrometry (GC-MS). A. sydowii exhibited promising potentials in the removal of PAHs.     

Effect of current density on groundwater arsenite removal performance using air cathode electrocoagulation

• With the same charge, current density had little effect on As(III) removal in ACEC. • ACEC had the lowest energy consumption compared with EC/O₂ or EC/N₂. • There was a trade-off relationship between energy consumption and removal time. • The ·OH concentration in ACEC was 1.5 times of that in the EC/O₂ system. Naturally occurring arsenic enrichment in groundwater poses a huge threat to human health. Air cathode electrocoagulation (ACEC) has recently been proposed to enhance As(III) oxidation and lower energy consumption. In this study, ACEC, EC/O₂ and EC/N₂ were evaluated with different current densities from 1 to 8 mA/cm² to investigate the effect on As(III) removal in different redox environments. Current density had no appreciable effect on arsenic removal efficiency given the same charge in ACEC because the concentration ratio of Fe/H₂O₂ under different current densities remained stable. However, in EC/O₂ and EC/N₂, As(III) removal was inhibited at higher current densities (4–8 mA/cm²), likely because more Fe(II) competed with As(III) for the oxidant, leading to less effective oxidation of As(III). In all EC systems, the ·OH units generated per power consumption reached the highest value at the lowest current density. Compared with other EC systems, the ACEC system showed lower energy consumption at all current densities due to the low energy consumption of the electrode reaction and more free radical generation. A lower current density saved more energy at the expense of time, showing the trade-off relationship between energy consumption and removal time. The operation costs for As(III) removal under optimal conditions were calculated as 0.028 $/m³ for ACEC, 0.030 $/m³ for EC/O₂, and 0.085 $/m³ for EC/N₂     

The performance of nitrate-reducing Fe(II) oxidation processes under variable initial Fe/N ratios: The fate of nitrogen and iron species

•Bacterially-mediated coupled N and Fe processes examined in incubation experiments. •NO₃⁻ reduction was considerably inhibited as initial Fe/N ratio increased. •The maximum production of N₂ occurred at an initial Fe/N molar ratio of 6. •Fe minerals produced at Fe/N ratios of 1–2 were mainly easily reducible oxides. The Fe/N ratio is an important control on nitrate-reducing Fe(II) oxidation processes that occur both in the aquatic environment and in wastewater treatment systems. The response of nitrate reduction, Fe oxidation, and mineral production to different initial Fe/N molar ratios in the presence of Paracoccus denitrificans was investigated in 132 h incubation experiments. A decrease in the nitrate reduction rate at 12 h occurred as the Fe/N ratio increased. Accumulated nitrite concentration at Fe/N ratios of 2–10 peaked at 12–84 h, and then decreased continuously to less than 0.1 mmol/L at the end of incubation. N₂O emission was promoted by high Fe/N ratios. Maximum production of N₂ occurred at a Fe/N ratio of 6, in parallel with the highest mole proportion of N₂ resulting from the reduction of nitrate (81.2%). XRD analysis and sequential extraction demonstrated that the main Fe minerals obtained from Fe(II) oxidation were easily reducible oxides such as ferrihydrite (at Fe/N ratios of 1–2), and easily reducible oxides and reducible oxides (at Fe/N ratios of 3–10). The results suggest that Fe/N ratio potentially plays a critical role in regulating N₂, N₂O emissions and Fe mineral formation in nitrate-reducing Fe(II) oxidation processes.     

Experimental and computational assessment of 1,4-Dioxane degradation in a photo-Fenton reactive ceramic membrane filtration process

• 1,4-Dioxane was degraded via the photo-Fenton reactive membrane filtration. • Degradation efficiency and AQY were both enhanced in photocatalytic membrane. • There is a tradeoff between photocatalytic degradation and membrane permeation flux. • Degradation pathways of 1,4-Dioxane is revealed by DFT analysis. The present study evaluated a photo-Fenton reactive membrane that achieved enhanced 1,4-Dioxane removal performance. As a common organic solvent and stabilizer, 1,4-Dioxane is widely used in a variety of industrial products and poses negative environmental and health impacts. The membrane was prepared by covalently coating photocatalyst of goethite (α-FeOOH) on a ceramic porous membrane as we reported previously. The effects of UV irradiation, H₂O₂ and catalyst on the removal efficiency of 1,4-Dioxane in batch reactors were first evaluated for optimized reaction conditions, followed by a systematical investigation of 1,4-Dioxane removal in the photo-Fenton membrane filtration mode. Under optimized conditions, the 1,4-Dioxane removal rate reached up to 16% with combination of 2 mmol/L H₂O₂ and UV₃₆₅ irradiation (2000 µW/cm²) when the feed water was filtered by the photo-Fenton reactive membrane at a hydraulic retention time of 6 min. The removal efficiency and apparent quantum yield (AQY) were both enhanced in the filtration compared to the batch mode of the same photo-Fenton reaction. Moreover, the proposed degradation pathways were analyzed by density functional theory (DFT) calculations, which provided a new insight into the degradation mechanisms of 1,4-Dioxane in photo-Fenton reactions on the functionalized ceramic membrane.     

Mechanism of dichloromethane disproportionation over mesoporous TiO2 under low temperature

• Mechanism of DCM disproportionation over mesoporous TiO₂ was studied. • DCM was completely eliminated at 350℃ under 1 vol.% humidity. • Anatase (001) was the key for disproportionation. • A competitive oxidation route co-existed with disproportionation. • Disproportionation was favored at low temperature. Mesoporous TiO₂ was synthesized via nonhydrolytic template-mediated sol-gel route. Catalytic degradation performance upon dichloromethane over as-prepared mesoporous TiO₂, pure anatase and rutile were investigated respectively. Disproportionation took place over as-made mesoporous TiO₂ and pure anatase under the presence of water. The mechanism of disproportionation was studied by in situ FTIR. The interaction between chloromethoxy species and bridge coordinated methylenes was the key step of disproportionation. Formate species and methoxy groups would be formed and further turned into carbon monoxide and methyl chloride. Anatase (001) played an important role for disproportionation in that water could be dissociated into surface hydroxyl groups on such structure. As a result, the consumed hydroxyl groups would be replenished. In addition, there was another competitive oxidation route governed by free hydroxyl radicals. In this route, chloromethoxy groups would be oxidized into formate species by hydroxyl radicals transfering from the surface of TiO₂. The latter route would be more favorable at higher temperature.     

Preparation of nZVI embedded modified mesoporous carbon for catalytic persulfate to degradation of reactive black 5

• The MCNZVI is prepared as an interesting material for PS activation. • Graphitized carbon shells facilitate electron transfer from Fe⁰. • The MCNZVI exhibits excellent performance to degrade RB5 by ¹O₂. • The MCNZVI has high stability and reusability in the oxidation system. High-efficiency and cost-effective catalysts with available strategies for persulfate (PS) activation are critical for the complete mineralization of organic contaminants in the environmental remediation and protection fields. A nanoscale zero-valent iron-embedded modified mesoporous carbon (MCNZVI) with a core-shell structure is synthesized using the hydrothermal synthesis method and high-temperature pyrolysis. The results showed that nZVI could be impregnated within mesoporous carbon frameworks with a comparatively high graphitization degree, rich nitrogen doping content, and a large surface area and pore volume. This material was used as a persulfate activator for the oxidation removal of Reactive Black 5 (RB5). The effects of the material dosage, PS concentration, pH, and some inorganic anions (i.e., Cl⁻, SO₄²⁻) on RB5 degradation were then investigated. The highest degradation efficiency (97.3%) of RB5 was achieved via PS (20 mmol/L) activation by the MCNZVI (0.5 g/L). The pseudo-first-order kinetics (k = 2.11 × 10⁻² min⁻¹) in the MCNZVI/PS (0.5 g/L, 20 mmol/L) was greater than 100 times than that in the MCNZVI and PS. The reactive oxygen species (ROS), including ¹O₂, SO₄^·−, HO^·, and ·O₂⁻, were generated by PS activation with the MCNZVI. Singlet oxygen was demonstrated to be the primary ROS responsible for the RB5 degradation. The MCNZVI could be reused and regenerated for recycling. This work provides new insights into PS activation to remove organic contamination.     

Precise regulation of acid pretreatment for red mud SCR catalyst: Targeting on optimizing the acidity and reducibility

• The optimum SCR activity was realized by tuning the acid pretreatment. • Optimized catalysts showed NO_x conversion above 90%. • The NH₃ and NO adsorption capacity of Al-O₃-Fe is stronger than Fe-O₃-Fe. • The formation of almandine consumes Fe³⁺ and Al³⁺ and weakens their interaction. Red mud (RM), as an alkaline waste, was recently proved to be a promising substitute for the SCR catalyst. Dealkalization could improve the acidity and reducibility of red mud, which were critical for SCR reaction. However, the dealkalization effect depended on the reaction between acid solution and red mud. In this study, we realized the directional control of the chemical state of active sites through tuning the acid pretreatment (dealkalization) process. The pretreatment endpoint was controlled at pH values of 3–5 with diluted nitric acid. When the pH values of red mud were 3 and 5 (CRM-3 and CRM-5), activated catalysts showed NO_x conversion above 90% at 275°C–475°C. The high initial reaction rate, Ce³⁺/(Ce³⁺ + Ce⁴⁺) ratio, and surface acidity accounted for the excellent SCR performance of CRM-5 catalyst. Meanwhile, more Fe³⁺ on the CRM-3 surface improved the NH₃ adsorption. There was a strong interaction between Al and Fe in both CRM-5 and CRM-3 catalysts. DFT results showed that the adsorption capacity of the Al-O₃-Fe for NH₃ and NO is stronger than that of Fe-O₃-Fe, which enhanced the NO_x conversion of the catalyst. However, the almandine was formed in CRM-4, consumed part of Fe³⁺ and Al³⁺, and the interaction between Al and Fe was weakened. Also, deposited almandine on the catalyst surface covered the active sites, thus leading to lower NH₃-SCR activity.     

Submerged arc plasma system combined with ozone oxidation for the treatment of wastewater containing non-degradable organic compounds

• Submerged arc plasma was introduced in terms of wastewater treatment. • Ozone oxidation was coupled with submerged arc plasma system. • Ozone was converted into O and O₂ by submerged arc plasma. • Decomposition rate was accelerated by submerged arc plasma. • Introduction of ozone led to significant increase in mineralization. Submerged arc plasma technology was assessed for the removal of phenols from wastewater. The OH radicals generated from the boundary between the plasma and waste solution were considered as a significant factor on the degradation reaction. In this study, the effects of highly energetic electrons released from the submerged arc plasma were mainly studied. The highly energetic electrons directly broke the strong chemical bond and locally increased the reaction temperatures in solution. The effects of the submerged-arc plasma on the decomposition of phenol are discussed in terms of the input energy and initial concentration. The single use of submerged arc plasma easily decomposed the phenol but did not increase the mineralization efficiency. Therefore, the submerged arc plasma, coupled with the ozone injection, was investigated. The submerged arc plasma combined with ozone injection had a synergic effect, which led to significant improvements in mineralization with only a small increase in input energy. The decomposition mechanism of phenol by the submerged arc plasma with the ozone was analyzed.     

One-step ball milling-prepared nano Fe2O3 and nitrogen-doped graphene with high oxygen reduction activity and its application in microbial fuel cells

• Nano Fe₂O₃ and N-doped graphene was prepared via a one-step ball milling method. • The maximum power density of Fe-N-G in MFC was 390% of that of pristine graphite. • Active sites like nano Fe₂O₃, pyridinic N and Fe-N groups were formed in Fe-N-G. • The improvement of Fe-N-G was due to full exposure of active sites on graphene. Developing high activity, low-cost and long durability catalysts for oxygen reduction reaction is of great significance for the practical application of microbial fuel cells. The full exposure of active sites in catalysts can enhance catalytic activity dramatically. Here, novel Fe-N-doped graphene is successfully synthesized via a one-step in situ ball milling method. Pristine graphite, ball milling graphene, N-doped graphene and Fe-N-doped graphene are applied in air cathodes, and enhanced performance is observed in microbial fuel cells with graphene-based catalysts. Particularly, Fe-N-doped graphene achieves the highest oxygen reduction reaction activity, with a maximum power density of 1380±20 mW/m² in microbial fuel cells and a current density of 23.8 A/m² at –0.16 V in electrochemical tests, which are comparable to commercial Pt and 390% and 640% of those of pristine graphite. An investigation of the material characteristics reveals that the superior performance of Fe-N-doped graphene results from the full exposure of Fe₂O₃ nanoparticles, pyrrolic N, pyridinic N and excellent Fe-N-G active sites on the graphene matrix. This work not only suggests the strategy of maximally exposing active sites to optimize the potential of catalysts but also provides promising catalysts for the use of microbial fuel cells in sustainable energy generation.     

Integration of microbial reductive dehalogenation with persulfate activation and oxidation (Bio-RD-PAO) for complete attenuation of organohalides

•Bio-RD-PAO can effectively and extensively remove organohalides. •Bio-RD alone effectively dehalogenate the highly-halogenated organohalides. •PAO alone is efficient in degrading the lowly-halogenated organohalides. •The impacts of PAO on organohalide-respiring microbial communities remain elusive. •Bio-RD-PAO provides a promising solution for remediation of organohalide pollution. Due to the toxicity of bioaccumulative organohalides to human beings and ecosystems, a variety of biotic and abiotic remediation methods have been developed to remove organohalides from contaminated environments. Bioremediation employing organohalide-respiring bacteria (OHRB)-mediated microbial reductive dehalogenation (Bio-RD) represents a cost-effective and environmentally friendly approach to attenuate highly-halogenated organohalides, specifically organohalides in soil, sediment and other anoxic environments. Nonetheless, many factors severely restrict the implications of OHRB-based bioremediation, including incomplete dehalogenation, low abundance of OHRB and consequent low dechlorination activity. Recently, the development of in situ chemical oxidation (ISCO) based on sulfate radicals (SO₄^·−) via the persulfate activation and oxidation (PAO) process has attracted tremendous research interest for the remediation of lowly-halogenated organohalides due to its following advantages, e.g., complete attenuation, high reactivity and no selectivity to organohalides. Therefore, integration of OHRB-mediated Bio-RD and subsequent PAO (Bio-RD-PAO) may provide a promising solution to the remediation of organohalides. In this review, we first provide an overview of current progress in Bio-RD and PAO and compare their limitations and advantages. We then critically discuss the integration of Bio-RD and PAO (Bio-RD-PAO) for complete attenuation of organohalides and its prospects for future remediation applications. Overall, Bio-RD-PAO opens up opportunities for complete attenuation and consequent effective in situ remediation of persistent organohalide pollution.     

Sorption mechanisms of diphenylarsinic acid on natural magnetite and siderite: Evidence from sorption kinetics,sequential extraction and extended X-ray absorption fine-structure spectroscopy analysis

• DPAA sorption followed pseudo-secondary and intra-particle diffusion models. • Chemical bonding and intra-particle diffusion were dominant rate-limiting steps. • DPAA simultaneously formed inner- and outer-sphere complexes on siderite. • DPAA predominantly formed occluded inner-sphere complexes on magnetite. • Bidentate binuclear bond was identified for DPAA on siderite and magnetite. Diphenylarsinic acid (DPAA) is both the prime starting material and major metabolite of chemical weapons (CWs). Because of its toxicity and the widespread distribution of abandoned CWs in burial site, DPAA sorption by natural Fe minerals is of considerable interest. Here we report the first study on DPAA sorption by natural magnetite and siderite using macroscopic sorption kinetics, sequential extraction procedure (SEP) and microscopic extended X-ray absorption fine-structure spectroscopy (EXAFS). Our results show that the sorption pseudo-equilibrated in 60 minutes and that close to 50% and 20%–30% removal can be achieved for magnetite and siderite, respectively, at the initial DPAA concentrations of 4–100 mg/L. DPAA sorption followed pseudo-secondary and intra-particle diffusion kinetics models, and the whole process was mainly governed by intra-particle diffusion and chemical bonding. SEP and EXAFS results revealed that DPAA mainly formed inner-sphere complexes on magnetite (>80%), while on siderite it simultaneously resulted in outer-sphere and inner-sphere complexes. EXAFS analysis further confirmed the formation of inner-sphere bidentate binuclear corner-sharing complexes (²C) for DPAA. Comparison of these results with previous studies suggests that phenyl groups are likely to impact the sorption capacity and structure of DPAA by increasing steric hindrance or affecting the way the central arsenic (As) atom maintains charge balance. These results improve our knowledge of DPAA interactions with Fe minerals, which will help to develop remediation technology and predict the fate of DPAA in soil-water environments.     

Comparison of different valent iron on anaerobic sludge digestion: Focusing on oxidation reduction potential,dissolved organic nitrogen and microbial community

• ORP value from −278.71 to −379.80 mV showed indiscernible effects on methane yield. • Fe(II) and Fe(III) promoted more degradation of proteins and amino acids than Fe⁰. • The highest enrichment of Geobacter was noted in samples added with Fe⁰. • Cysteine was accumulated during iron enhanced anaerobic sludge digestion. • Both iron content and valence were important for methane production. This study compared effects of three different valent iron (Fe⁰, Fe(II) and Fe(III)) on enhanced anaerobic sludge digestion, focusing on the changes of oxidation reduction potential (ORP), dissolved organic nitrogen (DON), and microbial community. Under the same iron dose in range of 0−160 mg/L after an incubation period of 30 days (d), the maximum methane production rate of sludge samples dosed with respective Fe⁰, Fe(II) and Fe(III) at the same concentration showed indiscernible differences at each iron dose, regardless of the different iron valence. Moreover, their behavior in changes of ORP, DON and microbial community was different: (1) the addition of Fe⁰ made the ORP of sludge more negative, and the addition of Fe(II) and Fe(III) made the ORP of sludge less negative. However, whether being more or less negative, the changes of ORP may show unobservable effects on methane yield when it ranged from −278.71 to −379.80 mV; (2) the degradation of dissolved organic nitrogen, particularly proteins, was less efficient in sludge samples dosed with Fe⁰ compared with those dosed with Fe(II) and Fe(III) after an incubation period of 30 d. At the same dose of 160 mg/L iron, more cysteine was noted in sludge samples dosed with Fe(II) (30.74 mg/L) and Fe(III) (27.92 mg/L) compared with that dosed with Fe⁰ (21.75 mg/L); (3) Fe⁰ particularly promoted the enrichment of Geobacter, and it was 6 times higher than those in sludge samples dosed with Fe(II) and Fe(III) at the same dose of 160 mg/L iron.