黄孢原毛平革菌对染料和印染废水的降解

白腐真菌黄孢原毛平革菌在合成木素过氧化物酶的限碳培养条件下，可以降解酶性、直接、活性、阳离子等多种类型的印染工业染料、在培养的d5木素过氧化物酶活力最高时，分别加入酸性染料卡布龙红和弱酸大红，质量浓度（ρ/mgL^-1)分别为25、50、100和12．5、25．50，48h后培养液基本脱色，较高浓度下菌膜上有残余染料吸附，5d后染料质量降解率分别是100％、88％、92％和58％、58％、65％、38％。以含有上述两种染料的印染废水置换培养液，并加入葡萄糖1g/L，黄孢原毛平革菌可以直接使废水脱色，菌丝可以重复培养脱色废水至少5批，每批废水的脱色率均大于90％，5批废水总的染料质量降解率约为80％，在重复培养脱色废水的过程中，测不到木素过氧化物酶的活力，说明废水中的染料分子是在细胞表面或进入胞内被降解的，若加入的葡萄糖浓度降低一半以上，菌丝脱色废水的效果将有所下降，图5表5参11     

固定化根霉脂肪酶的性质及在手性酯拆分中的应用

通过载体筛选及固定化过程优化，选用硅胶25℃吸附4h,1%戊二醛交联1h的方法对根霉（Rhizopus sp.Bc0-09m01)脂肪酶进行了固定化，对固定化酶的各种酶学性质进行的研究表明，酶的最适作用温度为40－45℃，是适作用pH为7．5，在4－30 ℃范围中性偏酸（pH4.0-9.0)环境中比较稳定，固定化酶的热稳定性及pH稳定性较游离酶有较大幅度的提高，将固定化酶用于拆分环氧丙醇丁酸酯，在转化率达到53％时得到的残留底物对映体过量值（ees)可达90％，固定化酶批式反应连续运行10批后酶活仍保持80％。     

Cu2+或表面活性剂AE对黄鳝肝损伤的超微结构观察

利用透射电镜研究了亚致死浓度的Cu^2 或表面活性剂AE(脂肪醇聚氧乙烯醚)对黄鳝肝细胞结构的损伤作用．观察发现，在ρ(Cu^2 )=4．5mg／L的污染环境中，黄鳝肝脏细胞核变形，染色质凝集，内质网囊泡化，细胞质中出现较多的溶酶体和过氧化物酶体；在ρ(AE)=4．0mg／L的表面活性剂污染下，黄鳝肝脏细胞核变形，内质网呈线状，溶酶体、过氧化物酶体体积大、数量多，部分细胞质解体，细胞中出现空腔甚至死亡．图版1参10     

固定化无花果曲霉对活性艳蓝KN-R的脱色

采用海藻酸钙法固定不同状态无花果曲霉，形成活菌固定化小球和死菌固定化小球。同时考察了不同因素如培养时间、温度、pH、染料浓度对活性艳蓝KN-R的脱色影响。试验结果表明：在33℃、pH为5．0、150r／min的振荡条件下，经66h它对活性艳蓝KN-R的脱色达到最佳效果。两种不同状态固定化小球的脱色率有较大的差别，其中活菌固定化小球的脱色率明显高于死菌固定化小球。其中活菌固定化小球经3次脱色后能重复使用，脱色率仍达79．8％。     

一株槭射脉革菌MY51的分离鉴定及对染料的脱色能力

通过对兔眼蓝莓叶片组织中分离得到的内生真菌MY51进行鉴定和产木质素降解酶活性检测,探讨该菌株对染料的脱色能力.通过形态学和分子生物学分类法对菌株MY51进行鉴定;对菌株MY51所产3种木质素降解酶酶活曲线进行测定;利用菌株MY51对固体条件下8种染料进行脱色能力的检测,筛选出较易脱色的染料后,以脱色效果较好的染料模拟污水染料,研究菌株MY51在静态条件下对不同浓度固体染料的脱色能力.结果表明,菌株MY51为白腐真菌——槭射脉革菌(Phlebia acerina),该菌株可以产木质素过氧化物酶、漆酶和锰过氧化物酶等木质素降解酶;且木质素过氧化物酶和锰过氧化物酶活性均在培养第8天达到最大值,分别为11.05、1.21 U/L;漆酶活性在第10天达到最大值18.52U/L;菌株MY51对不同的染料均有脱色效果,对活性红和活性黑的脱色效果最显著;但染料浓度较高时会对菌株MY51的脱色产生一定抑制作用,脱色15 d后,MY51对质量浓度为10、50、100、250和500 mg/L活性红脱色率分别为98.2%、94.5%、87.8%、88.3%和85.6%;对质量浓度为10、50、100、250和500mg/L的活性黑脱色率分别为98%、93%、83.3%、74.5%和65.5%.本研究表明菌株MY51对活性染料具有较好脱色能力,在染料废水处理领域具有一定的应用前景.(图10参31)     

芽孢杆菌发酵产碱性果胶酶温度控制策略

采用自行筛选获得一株产碱性果胶酶芽孢杆菌WSH03-09,在小型发酵罐中研究了不同温度对碱性果胶酶分批发酵的影响,结果表明,在恒定39℃条件下,可获得最高酶活5．39u／mL,各温度条件下的菌体干重相差不多,最终均能达11．5g／L左右;在发酵前期,控制温度41℃时最有利于菌体的生长,而在产物合成期,控制37℃有利于获得较高的产物合成比速,在此基础上,提出分阶段温度控制策略,采用此温度控制策略进行碱性果胶酶的发酵,碱性果胶酶酶活达5．99u／mL,比采用单一温度下的最大值提高了11％,其它各项指标也有较大提高．图6表1参6     

谷氨酰胺转胺酶(MTG)分批发酵中温度对S.mobaraense生长及产酶影响的模型化

研究了2.5L小罐培养过程中控制温度为25℃～35℃时对细胞生长和MTG合成的影响.结果表明当控制相对较低的温度时，细胞生长的延滞期较长，当控制温度较高时，细胞生长的延滞期较短，达到最大DCW和最高MTG酶活的时间均较短；通过研究各种不同模型对细胞生长的影响得到最适合描述S.mobaraense生长与温度之间的关系方程为Schoolfield方程；通过对最大DCW和最大MTG酶活进行数学模拟，发现方程X(U)=-a     

固定化多酚氧化酶对水中苯酚和氯酚的去除

以壳聚糖/蒙脱土插层复合物为载体,吸附法制备固定化多酚氧化酶,并以此催化氧化去除水中的苯酚、4-氯苯酚和2,4-二氯苯酚.考察了固定化多酚氧化酶的制备条件,对酚类化合物的催化氧化条件、动力学特性以及固定化酶的重复使用性能.结果表明,固定化多酚氧化酶的最佳制备条件为p H 5.0,酶与载体质量比20 mg·g-1,固定化6 h,所得固定化酶的载酶量为12.12 mg·g-1,每克单位载体酶活为12.76×103U·g-1.固定化多酚氧化酶对酚类化合物的最佳去除条件为:苯酚溶液p H 7.0,温度30℃;4-氯苯酚溶液p H 5.0,温度20℃;2,4-二氯苯酚溶液p H 5.0,温度30℃.在最佳反应条件下,酶与底物质量比为20 mg·mg-1时,固定化多酚氧化酶对苯酚、4-氯苯酚和2,4-二氯苯酚溶液去除率分别为63.6%、85.8%和87.8%.苯酚、4-氯苯酚和2,4-二氯苯酚的米氏常数Km值依次减小,最大反应速率Vmax依次增大,表明固定化酶对2,4-二氯苯酚的亲和力最强,催化速度最快.固定化酶循环使用6次(24 h)后对苯酚、4-氯苯酚和2,4-二氯苯酚的去除率分别为15.7%、24.2%和27.8%.     

辣根过氧化物酶在体外条件下对青蒿素生物合成的影响

通过细胞提取液，在体外条件下研究了辣根过氧化物酶对青蒿素生物合成的影响．细胞提取液以磷酸与Tris两种缓冲液制备．结果表明，辣根过氧化物酶在以磷酸缓冲液制备的细胞提取液中，很大地促进了青蒿素的生物合成，青蒿素的含量提高约1倍左右，而外加青蒿酸对青蒿素的生物合成并无显著的影响．以Tris缓冲液制备细胞提取液，外加过氧化物酶并不能促进青蒿素的生物合成．图4参12     

产富马酸酶菌种筛选及固定化细胞生产L-苹果酸转化条件研究

从土样中筛选得到２０支可将富马酸转化为Ｌ－苹果酸垢细菌菌株。经摇瓶复筛，得到一株富马酸酶活力较高的ＺＧ－４菌株。以改性ＰＶＡ为载体，制备得到固定化细胞。其较佳转化条件为：１经ｍｏｌ／Ｌ Ｎａ２Ｆｕ为底物，ｐＨ７．０，４０转化。固定化细胞经胆酸ρ＝４ｇ／Ｌ或ＴＰＣρ＝０．６ｇ／Ｌ预处理后，可有效抑制琥铂酸副产物的生成。添加没食子单宁ρ＝１ｇＬ，可使富马酸酶比活力达１．９５ｍｍｏｌ ｇ＾－ｈ＾－。固定     

汽爆麦草固态发酵木质素酶

木质素是地球上主要的可再生芳香族化合物 ,是地球上仅次于纤维素的第二丰富可再生天然资源 ,然而 ,对它的利用研究却很少 ,是天然高分子中未开发的领城[1] .80年代初发现了木质素过氧化物酶 (ＬｉＰ) [2 ,3] 和锰过氧化物酶 (ＭｎＰ) [4 ] 以后 ,木质素酶和木质素生物降解研究取得了一定进展 .但木质素微生物转化降解研究中仍存在许多问题 .( 1)由于木质素酶解是一种非专一性的、以自由基为基础的链反应过程[5] .因此 ,木质素酶在化学工业、煤化学和环境保护方面具有很大的开发前景 .而现在木质素酶的生产大多用合成培养基 ,必需添加昂贵的…     

Performance of completely autotrophic nitrogen removal over nitrite process under different aeration modes and dissolved oxygen

In this study, three sequential batch biofilm reactors (SBBRs) were operated for 155 days to evaluate the performance of completely autotrophic nitrogen removal over nitrite (CANON) process under different aeration modes and dissolved oxygen (DO). Synthetic wastewater with 160-mg NH4 ⁺-N/L was fed into the reactors. In the continuously-aerated reactor, the efficiency of the ammonium nitrogen conversion and total nitrogen (TN) removal reached 80% and 70%, respectively, with DO between 0.8–1.0 mg/L. Whereas in the intermittently-aerated reactor, at the aeration/non-aeration ratio of 1.0, ammonium was always under the detection limit and 86% of TN was removed with DO between 2.0–2.5 mg/L during the aeration time. Results show that CANON could be achieved in both continuous and intermittent aeration pattern. However, to achieve the same nitrogen removal efficiency, the DO needed in the intermittently-aerated sequential batch biofilm reactor (SBBR) during the aeration period was higher than that in the continuously-aerated SBBR. In addition, the DO in the CANON system should be adjusted to the aeration mode, and low DO was not a prerequisite to CANON process.     

Effect of exogenous 2,4-epibrassinolide on grain filling and yield formation of Tartary buckwheat北大核心CSCD

为明确外源2,4-表油菜素内酯影响苦荞生长、粒重与产量形成的生理机制,以苦荞品种晋荞2号为试验材料,研究不同浓度的外源2,4-表油菜素内酯处理(0、0.1、0.5、1.0和2.0 mg/L)对苦荞籽粒的灌浆特性、淀粉合成酶、根系形态及活力、叶片抗氧化酶活性及光合特性、农艺性状及产量的影响.结果表明:0.5 mg/L处理时苦荞籽粒的灌浆起始势(R0)、最大灌浆速率(Gmax)和平均灌浆速率(Gmean)最大,而达最大灌浆速率的时间(Tmax.G)最小;随2,4-表油菜素内酯施用量的增加,苦荞籽粒的腺苷二磷酸葡萄糖焦磷酸化酶(AGPase)和可溶性淀粉合成酶(SSS)活性、根系总长度等根系形态指标和根系活力、叶片抗氧化酶活性及光合特性指标、株高、主茎直径、单株粒重和千粒重均呈先增加后降低的趋势,且都在0.5 mg/L处理时达最大.外源2,4-表油菜素内酯的施用能在一定程度上促进苦荞产量的增加,其中0.1、0.5和1.0 mg/L处理与对照相比分别提高产量1.10、1.31和1.06倍,2.0 mg/L处理则降低0.96倍.本研究表明适宜的外源2,4-表油菜素内酯处理(0.5 mg/L)能促进苦荞籽粒灌浆,提高粒重和最终的产量.(图1表8参32)     

A gradient diver for measurement of respiration in individual organisms from the micro- and meiofauna

A gradient diver method suitable for gasometric studies on aquatic organisms of 1.0 g–1.0 mg wet weight is described. The microgasometer consists of an open glass capillary (diver) which encloses the biological object and an air bubble. It floats in an aqueous density gradient with constant pressure above the gradient. In response to changes in the volume of the air bubble, caused by consumption or release of gas by the biological object, the diver migrates either downwards or upwards in the gradient. On the basis of the rate of migration the rate of gas exchanges is calculated. The method is adaptable to a wide range of laboratory conditions and should also be of use in field laboratories.     

干旱区不同种植年限苜蓿人工草地土壤CO2排放的主要影响因素

采用静态箱-气象色谱法对干旱区不同种植年限苜蓿人工草地土壤系统、土壤-植被系统的CO2排放通量进行了测定,并对土壤 CO2排放通量的主要影响因素,包括土壤碳氮质量分数、土壤温度、气温、土壤水分体积分数、生物量进行了测定分析,从而得到了苜蓿生长季内CO2排放通量规律及影响土壤CO2排放的主要因素。结果表明：观测期内各个年限土壤-植被系统与土壤系统的CO2排放趋势基本一致,总体表现为4a〉5a〉8a〉3a〉1a,表现出“夏季高秋季低”的季节变化规律,具有明显的季节变化动态,各样地CO2通量在7月中旬达到最高排放通量;土壤CO2排放通量与0~20 cm土层内土壤有机碳质量分数、活性有机碳质量分数、土壤C：N及土壤全N质量分数都具有正相关关系,并且都达到了显著水平;土壤CO2排放通量与5 cm土壤温度和大气温度都有正相关关系,并且显著水平很高（P＜0.001）;土壤CO2排放通量与0~10 cm土壤水分体积分数之间没有显著的相关性（P〉0.05）;土壤CO2排放通量与地上部分生物量的大小有直接的正相关关系,并且CO2排放通量与地上生物量具有相同的变化趋势。     

Studies on in vitro degradability of mixed crude enzyme extracts produced from Pleurotus spp

A preliminary investigation was conducted to assess lignocellulolytic efficiency of crude extracts from three white-rot fungi, Pleurotus florida PF05 (PF), Pleurotus sajor-caju PS07 (PS) and Pleurotus eryngii PE08 (PE). The activities of CMC-ase, xylanase, beta-glucosidase, beta-xylosidase, laccase and Mn peroxidase in extracts were evaluated. PF produced its highest CMC-ase (317 UL(-1)'), beta-glucosidase (62 UL(-1)), beta-xylosidase (37 UL(-1)) and laccase (347 UL(-1)) activities while, PS produced highest xylanase (269 UL-(1)) and Mn peroxidase (69 UL(-1)) activities. In addition, crude extracts extracted were employed for their in vitro degradability assessment; and were evaluated with mono and mixed extracts separately to corn cob substrate. The losses in cell wall components and dry matter during 5 and 10 days incubations were analyzed after treatments of extracts. Maximum 8.2, 4.4 and 2.8% loss were found respectivelyin hemicellulose (HC), cellulose (C) and lignin (L) with mono extract of PF within 10 days. The influence of mono extract of each strain (PF PS and PE) and their mixed extracts (PF+PS, PF+PE, PS+PE and PF+PS+PE) on degradation of cell wall constituents were remarkably differed. The mixed extract treatment proved maximum 13.6% HC loss by PF+PS+PE extract, 9.2% loss in C by PF+PS extract and 5.2% loss of L by the PF+PS+PE extract treatment. The highest dry matter loss (8.2%) was recorded with PF+PS+PE mixed extract combination.     

Influence of glucose feeding on the ligninolytic enzyme production of the white-rot fungus Phanerochaete chrysosporium

The present work studied the influence of glucose feeding on the ligninolytic enzyme production of Phanerochaete chrysosporium in a nitrogen-limited (C/N ratio is 56/8.8 mmol/L) medium. Several sets of shaking flask experiments were conducted. The results showed that 2 g/L glucose feeding on the first day of the culture (24 h after the inoculation) simulated both fungal biomass growth and enzyme production. The manganese peroxidase (MnP) activity was 2.5 times greater than that produced in cultures without glucose feeding. Furthermore, the glucose feeding mode in fed-batch culture was also investigated. Compared to cultures with glucose feeding every 48 h, cultures with glucose feeding of 1.5 g/L (final concentration) every 24 h produced more enzymes. The peak and total yield of MnP activity were 2.7 and 3 times greater compared to the contrast culture, respectively, and the enzyme was kept stable for 4 days with an activity of over 200 U/L.     

Sorption of Cu and Zn by bone charcoal

Bone charcoal is being developed as a treatment for decontaminating polluted water. In particular, its potential to adsorb metal species from contaminated water supplies is being examined. In this study, bone charcoal was used in batch and column experiments designed to investigate the sorption of two cationic metals Cu and Zn. The data from batch experiments fitted the Langmuir isotherm and so theoretical maximum binding capacities could be obtained. These values were compared with experimental values derived from the column experiments. The mechanisms involved in the immobilisation were also investigated.     

Effects of Arbuscular mycorrhizal fungi isolated from white clovers (Trifolium repens L) on soil bacteria and fungi

White clover potted experiments were performed to investigate the effects of seven indigenous arbuscular mycorrhizal fungi (AMF) communities isolated from different test plots subjected to long-term fertilisation on soil enzyme activities, number of soil bacteria and fungi. The results showed that the inoculation of arbuscular mycorrhizal fungi communities increased the mycorrhizal infection rate of the plants and promoted the growth of plants. The Mnp treatment was most effective. The shoot biomass, root biomass, potassium and nitrogen uptake of the white clover in Mnp treatment group were increased by 61.54%, 84.00%, 62.50% and 46.71% respectively, compared with those in non-inoculation treatment. The inoculation of AMF communities had little effect on the number of bacteria in the soil, but significantly increased the number of soil fungi. Mnk treatment group had the highest number of fungi in the soil, which was 9.91 times that of the non-inoculation treatment group. The catalase and dehydrogenase activities were both significantly improved in Mnp treatment by 28.12% and 205.38% respectively, compared with those of the control treatment (-M). The urease, invertase and cellulase activities reached the highest levels in the Mck treatment; they were increased by 142.79%, 41.17% and 77.62% respectively, compared with those of the control treatment. Pearson correlation analysis showed that the soil enzyme activity was not correlated with the mycorrhizal infection rate, but correlated with the spore number of the AMF community. The impact of AMF community on soil quality is important for us to understand the function of the ecosystems. Relevant study provides important guidance for maintaining the balance of the soil-plant system and the development of sustainable agriculture.