In this research, supercritical carbon dioxide extraction (SFE) showed better extraction effect when compared with Solid- liquid extraction (SLE), Soxhlet extraction (SE) and Ultrasonic extraction (UE), not only in the rate but also the time. The comparison among these three extraction modifiers, including acetone, ethanol and methanol demonstrated that ethanol was preferred to SFE due to its high extraction effect and low toxicology. In addition, parameter of SFE, influence of temperature and pressure were investigated, and the best extraction effect was achieved at the optima conditions, temperature of 40°C and the pressure of 35 MPa. Thus, SFE is a highly effective method for flavonols extraction, requiring minimum energy and producing non-toxic byproduct. SFE-GC system is applied for the evaluation on flavonols that plays a key role in plant resistance to heavy metal, with its content and synthetase gene expression significantly increasing in plant when threatened by heavy metal. Besides, results indicated that flavonols can improve plant resistance to oxidative stress by quenching the redundant ROS in matrix.
Heterogeneous photocatalysis has long been considered to be one of the most promising approaches to tackling the myriad environmental issues. However, there are still many challenges for designing efficient and cost-effective photocatalysts and photocatalytic degradation systems for application in practical environmental remediation. In this review, we first systematically introduced the fundamental principles on the photocatalytic pollutant degradation. Then, the important considerations in the design of photocatalytic degradation systems are carefully addressed, including charge carrier dynamics, catalytic selectivity, photocatalyst stability, pollutant adsorption and photodegradation kinetics. Especially, the underlying mechanisms are thoroughly reviewed, including investigation of oxygen reduction properties and identification of reactive oxygen species and key intermediates. This review in environmental photocatalysis may inspire exciting new directions and methods for designing, fabricating and evaluating photocatalytic degradation systems for better environmental remediation and possibly other relevant fields, such as photocatalytic disinfection, water oxidation, and selective organic transformations.
In this paper, we present a three-step methodological framework, including location identification, bias modification, and out-of-sample validation, so as to promote human mobility analysis with social media data. More specifically, we propose ways of identifying personal activity-specific places and commuting patterns in Beijing, China, based on Weibo (China’s Twitter) check-in records, as well as modifying sample bias of check-in data with population synthesis technique. An independent citywide travel logistic survey is used as the benchmark for validating the results. Obvious differences are discerned from Weibo users’ and survey respondents’ activity-mobility patterns, while there is a large variation of population representativeness between data from the two sources. After bias modification, the similarity coefficient between commuting distance distributions of Weibo data and survey observations increases substantially from 23% to 63%. Synthetic data proves to be a satisfactory cost-effective alternative source of mobility information. The proposed framework can inform many applications related to human mobility, ranging from transportation, through urban planning to transport emission modeling.
The development of cost-effective and highly efficient anode materials for extracellular electron uptake is important to improve the electricity generation of bioelectrochemical systems. An effective approach to mitigate harmful algal bloom (HAB) is mechanical harvesting of algal biomass, thus subsequent processing for the collected algal biomass is desired. In this study, a low-cost biochar derived from algal biomass via pyrolysis was utilized as an anode material for efficient electron uptake. Electrochemical properties of the algal biochar and graphite plate electrodes were characterized in a bioelectrochemical system (BES). Compared with graphite plate electrode, the algal biochar electrode could effectively utilize both indirect and direct electron transfer pathways for current production, and showed stronger electrochemical response and better adsorption of redox mediators. The maximum current density of algal biochar anode was about 4.1 times higher than graphite plate anode in BES. This work provides an application potential for collected HAB to develop a cost-effective anode material for efficient extracellular electron uptake in BES and to achieve waste resource utilization.
A laboratory scale up-flow anaerobic sludge bed (UASB) bioreactor fed with synthetic wastewater was operated with simultaneous methanogenesis and denitrification (SMD) granules for 235 days with a gradient decrease of C/N. Molecular cloning, qRT-PCR and T-RFLP were applied to study the methanogenic community structures in SMD granules and their changes in response to changing influent C/N. The results indicate that when C/N was 20:1, the methane production rate was fastest, and Methanosaetaceae and Methanobacteriaceae were the primary methanogens within the Archaea. The richness and evenness of methanogenic bacteria was best with the highest T-RFLP diversity index of 1.627 in the six granular sludge samples. When C/N was reduced from 20:1 to 5:1, the methanogenic activity of SMD granules decreased gradually, and the relative quantities of methanogens decreased from 36.5% to 10.9%. The abundance of Methanosaetaceae in Archaea increased from 64.5% to 84.2%, while that of Methanobacteriaceae decreased from 18.6% to 11.8%, and the richness and evenness of methanogens decreased along with the T-RFLP diversity index to 1.155, suggesting that the community structure reflected the succession to an unstable condition represented by high nitrate concentrations.
Bioelectrochemical systems (BES) have been extensively studied for resource recovery from wastewater. By taking advantage of interactions between microorganisms and electrodes, BES can accomplish wastewater treatment while simultaneously recovering various resources including nutrients, energy and water (“NEW”). Despite much progress in laboratory studies, BES have not been advanced to practical applications. This paper aims to provide some subjective opinions and a concise discussion of several key challenges in BES-based resource recovery and help identify the potential application niches that may guide further technological development. In addition to further increasing recovery efficiency, it is also important to have more focus on the applications of the recovered resources such as how to use the harvested electricity and gaseous energy and how to separate the recovered nutrients in an energy-efficient way. A change in mindset for energy performance of BES is necessary to understand overall energy production and consumption. Scaling up BES can go through laboratory scale, transitional scale, and then pilot scale. Using functions as driving forces for BES research and development will better guide the investment of efforts.
Investigation of demulsification of polybutadiene latex (PBL) wastewater by polyaluminum chloride (PAC) indicated that there was an appropriate dosage range for latex removal. The demulsification mechanism of PAC was adsorption-charge neutralization and its appropriate dosage range was controlled by zeta potential. When the zeta potential of the mixture was between -15 and 15 mV after adding PAC, the demulsification effect was good. Decreasing the latex concentration in chemical oxygen demand (COD) from 8.0 g/L to 0.2 g/L made the appropriate PAC dosage range narrower and caused the maximum latex removal efficiency to decrease from 95% to 37%. Therefore, more accurate PAC dosage control is required. Moreover, adding 50 mg/L sulfate broadened the appropriate PAC dosage range, resulting in an increase in maximum latex removal efficiency from 37% to 91% for wastewater of 0.2 g COD/L. The addition of sulfate will favor more flexible PAC dosage control in demulsification of PBL wastewater.
Methane production from low-strength wastewater (LSWW) is generally difficult because of the low metabolism rate of methanogens. Here, an up-flow biofilm reactor equipped with conductive granular graphite (GG) as fillers was developed to enhance direct interspecies electron transfer (DIET) between syntrophic electroactive bacteria and methanogens to stimulate methanogenesis process. Compared to quartz sand fillers, using conductive fillers significantly enhanced methane production and accelerated the start-up stage of biofilm reactor. At HRT of 6 h, the average methane production rate and methane yield of reactor with GG were 0.106 m3/(m3·d) and 74.5 L/kg COD, which increased by 34.3 times and 22.4 times respectively compared with the reactor with common quartz sand fillers. The microbial community analysis revealed that methanogens structure was significantly altered and the archaea that are involved in DIET (such as Methanobacterium) were enriched in GG filler. The beneficial effects of conductive fillers on methane production implied a practical strategy for efficient methane recovery from LSWW.
Nitrous oxide (N2O), a potent greenhouse gas, is emitted during nitrogen removal in wastewater treatment, significantly contributing to greenhouse effect. Nitrogen removal generally involves nitrification and denitrification catalyzed by specific enzymes. N2O production and consumption vary considerably in response to specific enzyme-catalyzed nitrogen imbalances, but the mechanisms are not yet completely understood. Studying the regulation of related enzymes’ activity is essential to minimize N2O emissions during wastewater treatment. This paper aims to review the poorly understood related enzymes that most commonly involved in producing and consuming N2O in terms of their nature, structure and catalytic mechanisms. The pathways of N2O emission during wastewater treatment are briefly introduced. The key environmental factors influencing N2O emission through regulatory enzymes are summarized and the enzyme-based mechanisms are revealed. Several enzymebased techniques for mitigating N2O emissions directly or indirectly are proposed. Finally, areas for further research on N2O release during wastewater treatment are discussed.
Nitrogen (N) and phosphorus (P) released from the sediment to the surface water is a major source of water quality impairment. Therefore, inhibiting sediment nutrient release seems necessary. In this study, red soil (RS) was employed to control the nutrients released from a black-odorous river sediment under flow conditions. The N and P that were released were effectively controlled by RS capping. Continuous-flow incubations showed that the reduction efficiencies of total N (TN), ammonium (NH4+-N), total P (TP) and soluble reactive P (SRP) of the overlying water by RS capping were 77%, 63%, 77% and 92%, respectively, and nitrification and denitrification occurred concurrently in the RS system. An increase in the water velocity coincided with a decrease in the nutrient release rate as a result of intensive water aeration.
Polycyclic aromatic hydrocarbons (PAHs) often occur in oil-contaminated soil, coke wastewater and domestic sludge; however, associated PAH degraders in these environments are not clear. Here we evaluated phenanthrene degradation potential in the mixed samples of above environments, and obtained a methanogenic community with different microbial profile compared to those from sediments. Phenanthrene was efficiently degraded (1.26 mg/L/d) and nonstoichiometric amount of methane was produced simultaneously. 16S rRNA gene sequencing demonstrated that bacterial populations were mainly associated with Comamonadaceae Nocardiaceae and Thermodesulfobiaceae, and that methanogenic archaea groups were dominated by Methanobacterium and Methanothermobacter. Substances such as hexane, hexadecane, benzene and glucose showed the most positive effects on phenanthrene degradation. Substrate utilization tests indicated that this culture could not utilize other PAHs. These analyses could offer us some suggestions on the putative phenanthrene-degrading microbes in such environments, and might help us develop strategies for the removal of PAHs from contaminated soil and sludge.
This work presents an overall introduction to the Station for Observing Regional Processes of the Earth System–SORPES in Nanjing, East China, and gives an overview about main scientific findings in studies of air pollution-weather/climate interactions obtained since 2011. The main results summarized in this paper include overall characteristics of trace gases and aerosols, chemical transformation mechanisms for secondary pollutants like O3, HONO and secondary inorganic aerosols, and the air pollution–weather/climate interactions and feedbacks in mixed air pollution plumes from sources like fossil fuel combustion, biomass burning and dust storms. The future outlook of the development plan on instrumentation, networking and data-sharing for the SORPES station is also discussed.
Under the Stockholm Convention on Persistent Organic Pollutants (POPs), China is required not only to reduce polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/PCDF) but also unintentionally produced polychlorinated biphenyls (PCB), hexachlorobenzene (HCB) and pentachlorobenzene (PeCBz). A baseline of the sources in China that generate these unintentional POPs is needed for both research and regulation purposes. In this paper, we have compiled production data of potential sources in China and assessed them in five-year intervals from 2000 to 2015. Most of these activities experienced changes from rapid growth to slow growth. Measured data for PCB, HCB and PeCBz in samples collected from potential sources in China were reviewed. Most information was associated to thermal processes with high potential of emission, including waste incineration and ferrous and non-ferrous metal production. In addition, high levels of PCB, HCB and PeCBz were found as impurities in a few chlorinated products or as by-products in solvent production, which suggested organochlorine industry might be important sources. Finally, based on the studies reviewed, recommendations for future actions in research and policy as well as a few regulatory issues in China are discussed.
Fe-BEA catalysts are active for the NH3-SCR of NO. For industrial application, a binder should be added to the Fe-BEA catalysts to make them tightly adhere to the monoliths. The addition of alumina and zirconia as binders to the Fe-BEA led to a different effect on NO conversion. The catalytic activity of the mixed samples was evaluated by the temperature programmed procedure in a flow-reactor system, and the mechanism was analyzed via SEM, BET, XRD and XPS. It was found that larger iron particles were formed by the migration of parent iron particles in the Fe-BEA catalyst with alumina. This led to the increase of Fe3+ magnitude and iron cluster, enhancing the abilities of NO oxidation and storage. Accordingly, the SCR activity increased slightly in low temperature but decreased sharply in high temperature. For the Fe-BEA with zirconia sample, NO oxidation and storage abilities decreased due to the less iron clusters. The increase of Fe3+ magnitude resulted in higher catalytic oxidation ability, which gave rise to little change in the SCR activity compared with the Fe-BEA.
A membrane-aerated biofilm reactor was employed to investigate the nitrogen removal of one typical municipal reverse osmosis(RO) concentrate with a high total nitrogen (TN) concentration and a low C/ N ratio. The effects of operational conditions, including the aeration pressure, the hydraulic retention time and the C/N ratio, on the systematic performance were evaluated. The nitrogen removal mechanism was evaluated by monitoring the effluent concentrations of nitrogen contents. Furthermore, the microbial tolerance with elevated salinity was identified. The results indicated that the optimal TN removal efficiency of 79.2% was achieved of the aeration pressure of 0.02 MPa, hydraulic retention time of 24 h, and the C/N ratio of 5.8, respectively. It is essential to supplement the carbon source for the targeted RO concentrate to promote the denitrification process. The inhibitory effect of salinity on denitrifying bacteria and nitrite oxidizing bacteria was significant, revealing the limited TN removal capacity of the conditions in this work. The TN removal efficiency remained more than 70% with the addition of salt (NaCl) amount below 20 g/L. This work preliminarily demonstrated the MABR feasibility for the nitrogen removal of municipal RO concentrate with low C/N ratio and provided technical guidance for further scale-up application.
Ibuprofen (IBU) is widely used in the world as anti-inflammatory drug, which posed health risk to the environment. A bacterium capable of degrading IBU was isolated from activated sludge in a sewage treatment plant. According to its morphological, physiologic, and biochemical characteristics, as well as 16S rRNA sequence analysis, the strain was identified as Serratia marcescens BL1 (BL1). Degradation of IBU required the presence of primary substrate. After a five-day cultivation with yeast powder at 30°C and pH 7, the highest degradation (93.47%±2.37%) was achieved. The process of BL1 degrading IBU followed first-order reaction kinetics. The BL1 strain was applied to a small biological aerated filter (BAF) device to form a biofilm with activated sludge. IBU removal by the BAF was consistent with the results of static tests. The removal of IBU was 32.01% to 44.04% higher than for a BAF without BL1. The indigenous bacterial community was able to effectively remove CODMn (permanganate index) and ammonia nitrogen in the presence of BL1.
The issue of E-waste disposal is concerning all the stakeholders, from policymakers to the end users which have accelerated the research and development on environmentally sound disposal of E-waste. The recovery of metals (gold, tantalum, copper, iron etc.) from E-waste has become an important focus. The mechanical recycling, thermo-chemical processes like pyrolysis, pyro-, hydro- and biometallurgical processes can play important roles in the Metal Recovery from E-waste (MREW) technology. For the industrial application of the MREW technology, it is important to analyze the sustainability. In this paper, two case studies have been presented on E-waste recycling industries in India and China. Based on the literature data, an attempt has been made to assess qualitatively the overall sustainability of MREW technology considering the three pillars, i.e., environmental, economic and social. Two conceptual frameworks with (Option-2) and without (Option-1) pyrolysis for integrated MREW units have been developed and the generalized energy and environmental impact analysis has been made using the principles of LCA. The impacts of two options have been compared. Option 2 has been found to be more efficient and sustainable. It has been realized that climate change, fossil fuel depletion, water depletion, eutrophication, acidification, fresh and marine water ecotoxicity are possible impact categories. The recommendations based on the generalized assessment are in good agreement with the findings of previous researchers on individual steps of MREW unit. The findings of this paper are expected to be beneficial to researchers and stakeholders for research directions and decision making on MREW.
Effect of different carbon sources on purification performance and change of microbial community structure in a novel A2N-MBR process were investigated. The results showed that when fed with acetate, propionate or acetate and propionate mixed (1:1) as carbon sources, the effluent COD, NH4+-N, TN and TP were lower than 30, 5, 15 and 0.5 mg?L–1, respectively. However, taken glucose as carbon source, the TP concentration of effluent reached 2.6 mg?L–1. Process analysis found that the amount of anaerobic phosphorus release would be the key factor to determine the above effectiveness. The acetate was beneficial to the growth of Candidatus Accumulibacter associated with biological phosphorus removal, which was the main cause of high efficiency phosphorus removal in this system. In addition, it could eliminate the Candidatus Competibacter associated with glycogen-accumulating organisms and guarantee high efficiency phosphorus uptake of phosphorus accumulating organisms in the system with acetate as carbon source.
For biological nitrogen (N) removal from wastewater, a sufficient organic carbon source is requested for denitrification. However, the organic carbon/nitrogen ratio in municipal wastewater is becoming lower in recent years, which increases the demand for the addition of external organic carbon, e.g. methanol, in wastewater treatment. The volatile fatty acids (VFAs) produced by acidogenic fermentation of sewage sludge can be an attractive alternative for methanol. Chemically enhanced primary sedimentation (CEPS) is an effective process that applies chemical coagulants to enhance the removal of organic pollutants and phosphorus from wastewater by sedimentation. In terms of the chemical and biological characteristics, the CEPS sludge is considerably different from the conventional primary and secondary sludge. In the present study, FeCl3 and PACl (polyaluminum chloride) were used as the coagulants for CEPS treatment of raw sewage. The derived CEPS sludge (Fe-sludge and Al-sludge) was then processed with mesophilic acidogenic fermentation to hydrolyse the solid organics and produce VFAs for organic carbon recovery, and the sludge acidogenesis efficiency was compared with that of the conventional primary sludge and secondary sludge. The results showed that the Fe-sludge exhibited the highest hydrolysis and acidogenesis efficiency, while the Al-sludge and secondary sludge had lower hydrolysis efficiency than that of primary sludge. Utilizing the Fe-sludge fermentation liquid as the carbon source for denitrification, more than 99% of nitrate removal was achieved in the main-stream wastewater treatment without any external carbon addition, instead of 35% obtained from the conventional process of primary sedimentation followed by the oxic/anoxic (O/A) treatment.
Since the concept of the osmotic microbial fuel cell (OsMFC) was introduced in 2011, it has attracted growing interests for its potential applications in wastewater treatment and energy recovery. However, forward osmosis (FO) membrane fouling resulting in a severe water flux decline remains a main obstacle. Until now, the fouling mechanisms of FO membrane especially the development of biofouling layer in the OsMFC are not yet clear. Here, the fouling behavior of FO membrane in OsMFCs was systematically investigated. The results indicated that a thick fouling layer including biofouling and inorganic fouling was existed on the FO membrane surface. Compared to the inorganic fouling, the biofouling played a more important role in the development of the fouling layer. Further analyses by the confocal laser scanning microscopy (CLSM) implied that the growth of biofouling layer on the FO membrane surface in the OsMFC could be divided into three stages. Initially, microorganisms associated with ß-D-glucopyranose polysaccharides were deposited on the FO membrane surface. After that, the microorganisms grew into a biofilm caused a quick decrease of water flux. Subsequently, some of microorganisms were dead due to lack of nutrient source, in the meantime, polysaccharide and proteins in the biofouling layer were decomposed as nutrient source, thus leading to a slow development of the biofouling layer. Moreover, the microorganisms played a significant role in the formation and development of the biofouling layer, and further studies are needed to mitigate the deposition of microorganisms on FO membrane surfaces in OsMFCs.
