水处理无机混凝剂的研究进展

概略评述了国内外无机混凝剂的研究进展。无机混凝剂可分为铝盐类、铁盐类、铁铝复合类、活化硅酸等,聚合氯化铝（简称ＰＡＣ）是目前水处理中广泛应用的无机高分子混凝剂。无机复合类混凝剂是近来年发展十分迅速的水处理剂,聚硅酸铝盐类是其中的代表。文中对无机混凝剂今后的研究工作提出了建议,认为在无机混凝剂的研制开发中,要加强应用基础性研究,产品多样化、专门化,要降低生产成本,提高产品质量,进行优化研究。     

循环水旁滤中试研究

目前所使用的纤维束过滤器经多次检测出水浊度往往大于进水浊度,其主要原因是纤维束已受污染,并且很难冲洗干净。因此选用高效流砂过滤器进行循环水旁滤处理,实验表明在使用高效流砂过滤器时,投加聚合氯化铝(PAC)处理效果非常理想。在PAC投量为5～10 mg/L时,平均去除率达到83%,平均进水浊度7.05NTU,平均出水浊度为1.2NTU。完全能够满足旁滤的要求。     

聚合双酸铝铁在饮用水处理中的应用

阐述了新型高效水处理混凝剂—聚合双酸铝铁的研制机理及产品性能指标。汇集近几年来的实际应用数据,考察其在常温、高温、低温,高浊度、低浊度情况下与聚氯化铝PAC、硫酸铝AS的净水效果;通过搅拌试验对比对水中总铁、总锰的去除效果及残余铝含量。综合净水效果,聚合双酸铝铁明显优于聚氯化铝及硫酸铝。     

含腐殖酸的新型混凝剂强化混凝处理城市污水

研究了新型混凝剂BMT对城市污水进行强化混凝处理的效果，并与常用混凝剂聚合氯化铝（PAC）进行了比较。结果表明，在城市污水原水COD低于500mg／L和最佳工况下，经BMT处理后的出水能够达到《城镇污水处理厂污染物排放标准》（GB18918-2002）二级标准，并具备替代PAC的能力。     

聚合氯化铝与水解聚丙稀酰胺复合絮凝剂JX-3的制备及室内评价试验

在无机高分子絮凝剂聚合氯化铝(PAC)中引入有机高分子水解聚丙稀酰胺(PHP),制备出一种复合絮凝剂JX-3。PAC和PHP在其中可起到电性中和及絮凝桥架的的双重作用,使絮团紧密结合,提高絮凝效果,室内评价试验表明JX-3处理含轻油污水效果优于PAC和聚丙稀酰胺(PAM)。     

有机颜料废水的混凝预处理研究

利用絮凝剂阳离子聚丙烯酰胺(CPAM)和混凝剂聚合氯化铝(PAC)对有机颜料废水进行混凝处理,考察了单独使用CPAM、PAC及两者联合使用的处理效果,探讨了初始pH值、混凝剂投加量对处理效果的影响.结果表明,CPAM与PAC复配处理该废水时效果较好,水样pH值为7.0;CPAM与PAC的投药量分别为10mg/L和150mg/L时,浊度去除率可达97.56％.     

水泥工业生产废水治理及回用技术探讨

本文通过具体工程实例对水泥生产废水处理回用工程可行性、经济性等进行探讨,并提出切实可行的工艺流程,即：无机混凝剂（PAC）＋高分子助凝剂（PHM）的混凝沉淀处理工艺。     

废旧铝、铁片粉煤灰复合混凝剂的制备及在废水处理中的应用

我国粉煤灰和铝、铁片固体废物产量日益增多,危害越来越严重。在高温加热、搅拌条件下,用强酸浸渍粉煤灰和易拉罐碎片,使粉煤灰和废旧铝、铁片资源化,制得废旧铝、铁片粉煤灰复合混凝剂,并用所制得的废旧铝、铁片粉煤灰复合混凝剂处理屠宰废水。在一定条件下,经混凝试验处理后的屠宰废水pH值在7左右,COD去除率为92．0％,SS去除率为98．7％,浊度去除率为98．4％,色度去除率为96．6％。结果表明,粉煤灰和废旧铝、铁片资源化和在废水处理中的应用具有可行性。     

无机聚合硅铝混凝剂的合成及其在含油污水净化中的应用

本文以价廉、来源广的水玻璃及硫酸和硫酸铝（简称AS）为原料，制备无机聚合硅铝混凝剂（简称PSA)。对影响PSA产品稳定性的因素进行了讨论；考察了PSA在含油污水混凝脱油净化中的应用性能；并与聚氯化铝（简称PAC）及AS的性能进行了对比。结果表明，PSA是一种高效的含油污水脱油净化用混凝剂，可以使含油污水的处理费用大幅度下降。     

CM-3絮凝剂的室内研制及在含油污水处理中的应用

介绍复合高分子絮凝剂CM─3的研制。CM─3是以无机高分子聚合铝（PAC）、有机高分子改性聚丙烯酰胺（APAM）为主，添加少量的硫酸根离子及破乳剂复配而成的。经室内实验研究确定了适合的PAM分子量、改性PAM的胺甲基化度、PAM与PAC的比例以及其他组分的添加量，并与PAC比较进行了室内及现场应用试验，结果表明CM─3投药量为20～30mg／L时，炼油厂含油污水处理后的水质符合GB8978─88的标准。     

Electrocoagulation of vegetable oil refinery wastewater using aluminum electrodes

Electrocoagulation with aluminum electrodes was used to treat the vegetable oil refinery wastewater (VORW) in a batch reactor. The effects of operating parameters such as pH, current density, PAC (poly aluminum chloride) dosage and Na(2)SO(4) dosage on the removal of organics and COD removal efficiency have been investigated. It has been shown that the removal efficiency of COD increased with the increasing applied current density and increasing PAC and Na(2)SO(4) dosage and the most effective removal capacity was achieved at the pH 7. The results indicate that electrocoagulation is very efficient and able to achieve 98.9% COD removal in 90 min at 35 mAcm(-2) with a specific electrical energy consumption of 42 kWh(kgCOD(removed))(-1). The effluent was very clear and its quality exceeded the direct discharge standard.     

Characterization and coagulation of a polyaluminum chloride (PAC) coagulant with high Al13 content

A polyaluminum chloride (PAC) coagulant was prepared from AlCl3 x 6H2O and Na2CO3. The Al13 species in PAC was separated and purified by the SO4(2-)/Ba2+ deposition-replacement method, and characterized by 27Al-NMR and XRD. From 27Al-NMR spectroscopy, it was found that PAC obtained after separation and purification contained more Al13 (PAC-Al13, for short) than original PAC before separation and purification. In XRD spectra, a strong Al13 signal appeared in the range of 2theta from 5 to 25 degrees. Jar tests were performed to test the coagulation efficiency of AlCl3, PAC and PAC-Al13 in treating synthetic or actual water samples. Compared with PAC and AlCl3, PAC-Al13 gives the best results for turbidity, humic acid and color removal, and achieves the highest charge-neutralizing ability. Under the study conditions, PAC-Al13 gave about 90% humic acid removal and almost 100% reactive blue dye removal when its dosages were 4.0 and 15 mg/L as Al, respectively. The Al13 species has a higher positive charge and is the most effective polymeric Al species in water and wastewater treatment.     

Flocculation performance of epichlorohydrin-dimethylamine polyamine in treating dyeing wastewater

Epichlorohydrin-dimethylamine polymers with different intrinsic viscosity (η) and cationicity (τ) were synthesized. The flocculation performance and mechanism of these polymers in the removal of the reactive and disperse dyes from synthetic wastewater was investigated in terms of flocculation dynamics and color removal efficiency. The polymer flocculation efficiency was compared with that of polyaluminum chloride (PAC) and a composite flocculant based on polyaluminum chloride-epichlorohydrin-dimethylamine polyamine. The results showed that epichlorohydrin-dimethylamine polymer was effective over a pH range of 2–10 for the reactive and disperse dye removal (Reactive Brilliant Red and Disperse Yellow dyes). Epichlorohydrin-dimethylamine polymer with the highest η and τ gave the best reactive dye removal efficiency, and its adsorption-bridging and electric neutralization ability played important roles in the flocculation process. The higher the η viscosity of the epichlorohydrin-dimethylamine polymer, the better the flocculation performance of epichlorohydrin-dimethylamine polyamine, and stronger adsorption-bridging ability was obtained for removing the disperse dye from dyeing wastewaters. Epichlorohydrin-dimethylamine polymer achieved better decolorization performance when used together with PAC.     

Color removal from dye-containing wastewater by magnesium chloride

Color removal by MgCl(2) when treating synthetic waste containing pure dyes was studied. The color removal efficiency of MgCl(2)/Ca(OH)(2) was compared with that of Al(2)(SO(4))(3), polyaluminum chloride (PAC) and FeSO(4)/Ca(OH)(2). The mechanism of color removal by MgCl(2) was also investigated. The experimental results show that the color removal efficiency of MgCl(2) is related to the type of dye and depends on the pH of the waste and the dosage of the coagulants used. Treatment of waste containing reactive dye or dispersed dye with MgCl(2) yielded an optimum color removal ratio when the pH of the solution was equal to or above 12.0. For both the reactive and dispersed dye waste, MgCl(2)/Ca(OH)(2) was shown to be superior to MgCl(2)/NaOH, Al(2)(SO(4))(3), PAC and FeSO(4)/Ca(OH)(2) for color removal. A magnesium hydroxide precipitate formed at pH values greater than 12.0, which provided a large adsorptive surface area and a positive electrostatic surface charge, enabling it to remove the dyes through charge neutralization and an adsorptive coagulating mechanism. So, the MgCl(2)/Ca(OH)(2) system is a viable alternative to some of the more conventional forms of chemical treatment, especially for treating actual textile waste with high natural pH.     

黄浦江上游原水强化处理选炭试验研究

以黄浦江上游水源为原水,通过煤质炭、竹质炭、椰壳炭等炭种筛选小试和中试试验,研究了黄浦江上游原水中有机污染物强化去除的最佳炭种及其最佳投加量。结果表明黄浦江上游原水中投加PAC能够改善处理后水质,提高原水中有机物的去除效果;并且随着PAC投加量的增加,原水中有机物去除效果增强;综合性价比、碳源等因素确定竹质炭较为经济合理;当竹质炭投加量为10～15mg/L时,处理后出水CODMn可达到3mg/L或以下。     

Effects of alum and aluminum chloride on phosphorus runoff from swine manure

Phosphorus (P) runoff from fields fertilized with swine (Sus scrofa domesticus) manure may contribute to eutrophication. The objective of this study was to evaluate the effect of aluminum sulfate (alum) and aluminum chloride applications to swine manure on P runoff from small plots cropped to tall fescue (Festuca arundinacea Shreb.). There were six treatments in this study: (i) unfertilized control plots, (ii) untreated manure, (iii) manure with alum at 215 mg Al L(-1), (iv) manure with aluminum chloride at 215 mg Al L(-1), (v) manure with alum at 430 mg Al L(-1), and (vi) manure with aluminum chloride at 430 mg Al L(-1). Manure application rates were equivalent to approximately 125 kg N ha(-1). Alum and aluminum chloride additions lowered soluble reactive phosphorus (SRP) levels from about 130 mg P L(-1) to approximately 30 mg P L(-1) at low rates. At high rates, SRP levels in swine manure were around 1 mg P L(-1). Soluble reactive P concentrations in runoff were 5.50, 3.66, 3.00, 0.87, 0.87, and 0.55 mg P L(-1), for normal manure, low alum, low aluminum chloride, high alum, high aluminum chloride, and unfertilized control plots, respectively. Hence, high alum and aluminum chloride reduced SRP concentrations in runoff by 84% and were not statistically different from SRP concentrations in runoff from unfertilized control plots. These data indicate that treating swine manure with alum or aluminum chloride could result in significant reductions in nonpoint-source P runoff.     

Response surface optimization of acid red 119 dye from simulated wastewater using Al based waterworks sludge and polyaluminium chloride as coagulant

In this research, the performance of Polyaluminium Chloride (PAC) and Polyaluminium Chloride sludge (PACS) as coagulants for acid red 119 (AR119) dye removal from aqueous solutions were compared. The sample of PACS was collected from "Baba Sheikh Ali" water treatment plant (Isfahan, Iran) where PAC is used as a coagulant in the coagulation/flocculation process. A response surface methodology was applied to evaluate the simple and combined effects of the operating variables including initial pH, coagulant dosage and initial dye concentration and to optimize the operating conditions of the treatment process. Results reveal that the optimal conditions for dye removal were initial pH 3.42, coagulant dosage of 4.55 g dried PACS/L and initial dye concentration of 140 mg/L for PACS, while the optimal initial pH, coagulant dosage and initial dye concentration for PAC were 3.8, 57 mg/L and 140 mg/L, respectively. Under these optimal values of process parameters, the dye removal efficiency of 94.1% and 95.25% was observed for PACS and PAC, respectively. Although lower amount of PAC in comparison with PACS was needed for specific dye removal, the reuse of PACS as a low-cost material can offer some advantages such as high efficiency for AR119 dye removal and economic savings on overall water and wastewater treatment plant operation costs.     

炼厂隔油后污水的有机构成及混凝处理

采用GC/MS技术分析了炼厂隔油后污水的有机组成,并研究了不同混凝剂处理污水的效果,以及对有机构成的影响。结果表明,隔油后污水中的有机物质主要是C6–C8,其中酚类物质的含量最高;PAM和PAC混凝处理隔油后污水,可使污水中的有机物质总浓度及各物质的相对比例均发生变化,PAM降低烃类物质的效果好于PAC,而后者降低酚类物质的效果好于前者;在PAC处理污水时,同时投加少量活性炭可有效改变PAC脱除COD的性能。