The influence of the precursor and synthesis method on the CO2 capture capacity of carpet waste-based sorbents

Adsorption is one of the most promising technologies for reducing CO₂ emissions and at present several different types of sorbents are being investigated. The use of sorbents obtained from low-cost and abundant precursors (i.e. solid wastes) appears an attractive strategy to adopt because it will contribute to a reduction not only in operational costs but also in the amount of waste that is dumped and burned in landfills every year. Following on from previous studies by the authors, in this work several carbon-based adsorbents were developed from different carpet wastes (pre-consumer and post-consumer wastes) by chemical activation with KOH at various activation temperatures (600–900 °C) and KOH:char impregnation ratios (0.5:1 to 4:1). The prepared materials were characterised by chemical analysis and gas adsorption (N₂, −196 °C; CO₂, 0 °C), and tested for CO₂ adsorption at temperatures of 25 and 100 °C. It was found that both the type of precursor and the conditions of activation (i.e. impregnation ratios, and activation temperatures), had a huge influence on the microporosity of the resultant samples and their CO₂ capture capacities. The carbon-based adsorbent that presented the maximum CO₂ capture capacities at 25 and 100 °C (13.8 wt.% and 3.1 wt.%, respectively), was prepared from a pre-consumer carpet waste and was activated at 700 °C using a KOH:char impregnation ratio of 1:1. This sample showed the highest narrow microporosity volume (0.47 cm³ g⁻¹), thus confirming that only pores of less than 1 nm are effective for CO₂ adsorption at atmospheric pressure.     

Preparation of activated carbons from unburnt coal in bottom ash with KOH activation for liquid-phase adsorption

In this work, unburnt coal (UC) in bottom ash from coal-fired power plants was soaked in KOH solution and activated for 1 h at 780 °C. The yield of activated carbons varied from 47.8 to 54.8% when the KOH/UC weight ratio changed from 2 to 4. Pore properties of these activated carbons including the BET surface area, pore volume, pore size distribution, and pore diameter were characterized based on N₂ adsorption isotherms. It was shown that the isotherms for the adsorption of methylene blue, acid blue 74, and 4-chlorophenol from aqueous solutions on these activated carbons at 30 °C were well fitted by the Langmuir equation (correlation coefficient r² > 0.9968). The adsorption capacities of methylene blue, acid blue 74, and 4-chlorophenol were obtained to be 2.40–2.88, 0.57–1.29, and 2.34–5.62 mmol/g, respectively. Moreover, the adsorption kinetics could be suitably described by the Elovich equation.     

Kinetic studies on the adsorption of phenol, 4-chlorophenol,and 2,4-dichlorophenol from water using activated carbons

This study uses rate parameters in pseudo-first-order (PFO) and pseudo-second-order (PSO) equations (k₁ and k₂q_e, respectively) to judge the extent for approaching equilibrium in an adsorption process. Out of fifty-six systems collected from the literature, the adsorption processes with a k₂q_e value between 0.1 and 0.8 min^?1 account for as much as 70% of the total. These are classified as fast processes. This work compares the validity of PFO and PSO equations for the adsorption of phenol, 4-chlorophenol (4-CP), and 2,4-dichlorophenol (2,4-DCP) on activated carbons prepared from pistachio shells at different NaOH/char ratios. The activated carbons, recognized as microporous materials, had a surface area ranging from 939 to 1936 m²/g. Findings show that the adsorption of phenol, 4-CP, and 2,4-DCP on activated carbons had a k₂q_e value of 0.15–0.58 min^?1, reflecting the fast process. Evaluating the operating time by rate parameters revealed that k₂q_e was 1.6–1.8 times larger than k₁. These findings demonstrate the significance of using an appropriate kinetic equation for adsorption process design.     

SO2 gas adsorption by modified kaolin clays: influence of previous heating and time acid treatments

Modified kaolin clays were used as adsorbents for SO(2) gas adsorptions. The clays were heated up to 900 °C previous to acid treatments with 0.5 N sulfuric acid solutions at boiling temperature during different times up to 1440 min. Equilibrium adsorption at 25 °C and 0.1 MPa was carried out by using a volumetric apparatus. The samples were characterized by chemical analysis, X-ray diffraction and infrared analysis. The heating of the clays followed by acid treatment improved the adsorption capacity of the kaolin clays. The presence of amorphous silica and hydroxyl in the final products improved SO(2) adsorption capacity. Better properties for SO(2) adsorption were found in kaolin rich in not well ordered kaolinite clay mineral.     

Preparation and characterization of activated carbon from a new raw lignocellulosic material: Flamboyant (Delonix regia) pods

Activated carbons were prepared from flamboyant pods by NaOH activation at three different NaOH:char ratios: 1:1 (AC-1), 2:1 (AC-2), and 3:1 (AC-3). The properties of these carbons, including BET surface area, pore volume, pore size distribution, and pore diameter, were characterized from N₂ adsorption isotherms. The activated carbons obtained were essentially microporous and had BET surface area ranging from 303 to 2463 m² g⁻¹.¹³C (CP/MAS and MAS) solid-state NMR shows that the lignocellulosic structures were completely transformed into a polycyclic material after activation process, thermogravimetry shows a high thermal resistance, Boehm titration and Fourier-transform infrared spectroscopy allowed characterizing the presence of functional groups on the surface of activated carbons. Scanning electron microscopy images showed a high pore development. The experimental results indicated the potential use of flamboyant pods as a precursor material in the preparation of activated carbon.     

Removal of the hazardous dye rhodamine B through photocatalytic and adsorption treatments

This paper reports on photocatalytic and adsorptive treatment of a hazardous xanthene dye, Rohdamine B, in wastewater. The photocatalytic degradation was carried out in the presence of the catalyst TiO(2) and the effects of pH, concentration of the dye, amount of TiO(2), temperature and electron acceptor H(2)O(2) on the degradation process were observed. It was found that photocatalytic degradation by TiO(2) is an effective, economical and faster mode of removing Rohdamine B from aqueous solutions. Attempts were also made to utilize activated carbon and rice husk as potential adsorbents to remove Rhodamine B from wastewater. The adsorption studies were carried out at 40, 50 and 60 degrees C, and the effects of pH, temperature, amount of adsorbents, concentration of adsorbate, etc., on the adsorption were measured. On the basis of adsorption data the Langmuir and Freundlich adsorption isotherm models were also confirmed. The adsorption isotherm constants thus obtained were employed to calculate thermodynamic parameters like Gibb's free energy, change in enthalpy and entropy. In order to observe the quality of wastewater COD measurements were also carried out before and after the treatments. A significant decrease in the COD values was observed, which clearly indicates that both photocatalytic and adsorption methods offer good potential to remove Rhodamine B from industrial effluents.     

Decomposition of NaBH4 with self-regeneration of carbon-supported CoCl2 catalyst

In this study, economically favorable CoCl₂ catalysts at four different amounts were supported on activated carbon (AC) for NaBH₄ dehydrogenation. Supported catalyst could achieve hydrogen release for 2,060 cycles, which is equivalent to 103 days of uninterrupted operation. Slow and continuous hydrogen release was observed in all experiments. Even 1 g of NaBH₄ can carry 1.2 L of hydrogen, and in hydrolysis process, it liberates 2.5 L of hydrogen that indicates the decomposition of water. EDX analysis and reverse burette measurements show that CoCl₂ could be homogeneously distributed on and permanently joined to the support surface. Kinetic investigation of the dehydrogenation reaction fits zero order kinetics, and activation energy was calculated to be 48 kJ/mol.     

Comparison and application of different component municipal solid wastes based carbon on adsorption of carbon dioxide

The prepared different components municipal solid wastes based carbons were used to investigate the adsorption of CO₂. The optimum conditions for CO₂ adsorption were investigated firstly. And then, the CO₂ adsorption performance of different components based carbon adsorbents were compared with each other under the optimum parameters. The results illustrated that the triple components (pinewood, acrylic textile, and tire) based carbon exhibited the best adsorption performance, which is 1.522 mmol/g and its physical prosperity was also conducted to interpret the adsorption mechanism. Besides, to further approach to the actual gas, the influence of additional O₂ and SO₂ on CO₂ adsorption properties of ternary-component-based carbon was investigated. The results illustrate that O₂ concentration exerts little effect on adsorption capacity. SO₂ plays the dominated role in the competitive adsorption effect.     

Adsorption of carbon dioxide using impregnated activated carbon promoted by Zinc

The effect of impregnation of activated carbon with Cr₂O and Fe₂O₃ and promotion by Zn²⁺ on its adsorptive properties of carbon dioxide was studied using a volumetric adsorption apparatus at ambient temperature and low pressures. Slurry and solution impregnation methods were used to compare CO₂ capture capacity of the impregnated activated carbon promoted by Zinc. The obtained adsorption isotherms showed that amount of CO₂ adsorbed on the samples impregnated by Cr₂O was increased about 20% in compare to raw activated carbon. The results also showed that Fe₂O₃ was not an effective impregnating species for activated carbon modification. Moreover slurry impregnation method showed higher CO₂ adsorption capacity in comparison with solution impregnation method. Samples prepared by co-impregnation of two metal species showed more adsorption capacity than samples impregnated by just one metal species individually. Washing the impregnated samples by metal oxide resulted in 15% increase in CO₂ adsorption capacities of activated carbons which can be attributed to the metal oxides removal covering the adsorption surface. Decreasing impregnation temperature from 95 to 25 °C in solution method showed a significant increase in CO₂ adsorption capacity. Sips equation was found a suitable model fitting to the adsorption data in the range studied.     

Emission of CO2, CH4 and N2O from freshwater marsh in northeast of China

The wetlands play an important role in carbon storage, especially at high latitudes, at which they store nearly one-third of global soil carbons. However, few studies have investigated the emissions of CO(2), CH(4) and N(2)O in the long-term, especially effects of freeze-thaw cycles on these gases emissions in freshwater marsh ecosystems. In this paper, we collected greenhouse gas emission data from a freshwater marsh area in China for 4 years, evaluated their release variables and speculated on their potential atmospheric impact. For this paper, we report on the CO(2), CH(4) and N(2)O emission rates recorded from June 2002 to November 2005 in the Sanjiang Plain of northeast China. We measured their interannual variations and fluctuations, as well as factors affecting their emissions, and estimated their regulation and freeze-thaw cycle impacts. Our results revealed obvious CO(2) and CH(4) emission fluctuations during the winter months, and during the freeze-thaw cycle, and a strong interannual variation during the growing season. Overall, we documented a close relationship between the CO(2) and CH(4) emissions, implicating some regulatory commonality. We determined that the marsh was a N(2)O sink during the winter, but a significant source of N(2)O during the freeze-thaw cycle as the temperature increased, especially in early summer. During the thaw-freeze period, the N(2)O levels were positively correlated with the water depth. Additionally, water depth greatly governed the interannual variation of the N(2)O emissions from the marshes during the thaw-freeze period.     

Removal of polycyclic aromatic hydrocarbons from aqueous solution on soybean stalk-based carbon

Soybean [ (L.) Merr.] stalk-based carbons were prepared by phosphoric acid activation at different carbonization temperatures. Characteristics of the prepared carbon, including specific surface area, iodine number, and amount of methylene blue sorption, were determined. Experiments on phenanthrene, naphthalene, and acenaphthene, as representatives of polycyclic aromatic hydrocarbons (PAHs), removal from aqueous solution by the prepared carbon were conducted at different levels of carbon addition. The results indicated that the specific surface area, iodine number, and amount of methylene blue sorption increased with an increase of carbonization temperature. The maximum values were observed at 700°C and were 287.63 m g, 508.99 mg g, and 90.14 mg g, respectively. The removal efficiencies of phenanthrene, naphthalene, and acenaphthene tended to increase with increasing carbon amounts and carbonization temperature. The optimal removal performance was obtained under the experimental conditions of carbon concentrations of 0.04 g 32 mL and carbonization temperature of 700°C, and the removal efficiencies of phenanthrene, naphthalene, and acenaphthene were 99.89, 100, and 95.64%, respectively. The performance of the prepared carbon was superior to that of commercial activated carbon. Additionally, for the same carbon concentrations, the removal efficiency of PAHs on prepared carbons followed the order: phenanthrene > naphthalene > acenaphthene. Results obtained from this work provide some insight into the reuse of an agricultural residue, and also provide a new application for the treatment of PAHs in contaminated water utilizing activated carbon prepared from agricultural residues.     

Adsorption of cadmium on carbonaceous adsorbents developed from used tire rubber

Carbonaceous adsorbents (CAs) are developed from used tire rubber (UTR) and tested as adsorbents of Cd(2+) in aqueous solution. In the preparation of the CAs, UTR was treated thermally at 400-900 °C for 2 h in N(2) and at 850 °C for 2 h in steam. Concentrated NaOH, HCl, H(2)SO(4), HNO(3) and H(2)O(2) solutions were also used. UTR and H900 (i.e. UTR pyrolyzed at 900 °C) were treated with O(3) at 25 °C for 1 h and with air at 250 °C for 1 and 24 h. CAs were characterized texturally by N(2) adsorption at -196 °C, mercury porosimetry, and density measurements. The surface groups were analyzed by FT-IR spectroscopy. Using the batch method, the adsorption process of Cd(2+) was studied mainly from the kinetic standpoint at various pH values of the adsorptive solution. Significant porosity developments are achieved only when UTR is heat-treated, in particular in steam. However, the variety and concentration of surface groups are low in CAs. This is so even for CAs prepared using oxidizing agents as strong as O(3) and H(2)O(2), which has been associated with a lack of available or accessible surface active sites for oxidation in UTR and H900, respectively. Thermal and thermal-chemical treatments are usually more effective than chemical treatments to increase the adsorption of Cd(2+) in aqueous solution. The adsorption process of Cd(2+) is first fast and then much slower. Adsorption-time data fit better to a pseudo-second order kinetic equation than to a pseudo-first order kinetic equation. The extent to which the adsorption process occurs is strongly dependent on the pH of the Cd(2+) solution, being larger at pH 4.6 or 7.0 according to the adsorbent.     

Adsorption of pharmaceuticals to microporous activated carbon treated with potassium hydroxide, carbon dioxide, and steam

Adsorption of sulfapyridine, tetracycline, and tylosin to a commercial microporous activated carbon (AC) and its potassium hydroxide (KOH)-, CO-, and steam-treated counterparts (prepared by heating at 850°C) was studied to explore efficient adsorbents for the removal of selected pharmaceuticals from water. Phenol and nitrobenzene were included as additional adsorbates, and nonporous graphite was included as a model adsorbent. The activation treatments markedly increased the specific surface area and enlarged the pore sizes of the mesopores of AC (with the strongest effects shown on the KOH-treated AC). Adsorption of large-size tetracycline and tylosin was greatly enhanced, especially for the KOH-treated AC (more than one order of magnitude), probably due to the alleviated size-exclusion effect. However, the treatments had little effect on adsorption of low-size phenol and nitrobenzene due to the predominance of micropore-filling effect in adsorption and the nearly unaffected content of small micropores causative to such effect. These hypothesized mechanisms on pore-size dependent adsorption were further tested by comparing surface area-normalized adsorption data and adsorbent pore size distributions with and without the presence of adsorbed antibiotics. The findings indicate that efficient adsorption of bulky pharmaceuticals to AC can be achieved by enlarging the adsorbent pore size through suitable activation treatments.     

Removal of phenol from aqueous solution by adsorption onto OTMAC-modified attapulgite

The potential of octodecyl trimethyl ammonium chloride (OTMAC)-modified attapulgite (AT) for phenol adsorption from aqueous solutions was studied. The comparison of natural AT and modified AT showed that it is possible to utilize the sonication-modified OTMAC-AT in the treatment of phenol-contaminated wastewaters. Batch sorption studies were carried out to evaluate the effect of contact time, shaking frequency, temperature and the amount of AT. The results showed that in a lab-scale reactor, at room temperature, with an amount of the modified AT added (2.5 g), and a shaking frequency of 140 rev/min, the adsorption rate of phenol could be 60.4% for a duration of 60 min. The sorption kinetics were described by a pseudo-second-order model, and the values of k and q(e) were 1.367 mg/ig min and 0.7901 ig/mg, respectively. The analysis of equilibrium data showed that the Freundlich isotherms were found to be applicable for the adsorption equilibrium data. K and 1/n were estimated to be 14.53 and 0.8438, respectively.     

Extra-framework cation release from heulandite-type rich tuffs on exchange with NH(4)(+)

The outgoing cations of Greek heulandite-rich tuff samples (heulandite type-III, 91wt.%, mica 4wt.%, feldspar 5wt. %, CEC 2.22meq/g) were analysed upon exchange with ammonium acetate using atomic absorption spectrometry (AAS). The kinetic curves of each cation were investigated over a total time of contact of 720h with sampling at frequent intervals. The materials were examined by powder X-ray diffraction, SEM-EDS, and AAS. The sorption ability was measured using the ammonium acetate saturation method. It was found that Ca(2+) presents an unexpected extra-framework release and a surprisingly high degree of exchange (90%). The exchange of Mg (57%) is also worthy of note whereas the behavior of K(+) showed an expected rapid initial release. The behavior of Na(+) must be similar. However, its lower concentration in the zeolitic material minimizes its overall significance somewhat. On the other hand, Ca(2+) and Mg(2+) release is kinetically much slower, compared to that of alkali metal ions, and this phenomenon indicates that different exchange energies are needed till final equilibrium.     

Retention of gases by hexadecyltrimethylammonium-montmorillonite clays

Intercalated montmorillonite clays with different amounts of organic hexadecyltrimethylammonium (HDTMA) cations were studied to analyse their CO, CH(4), and SO(2) gas retentions. Equilibrium adsorption was measured by using a standard volumetric apparatus at 25 degrees C and 0.1 MPa. The solids were characterised by X-ray diffraction. The levels of adsorption of SO(2) by organo-montmorillonites (0.3595-1.6403 mmol/g) were higher than those of CO (up to 0.0202 mmol/g) and CH(4) (up to 0.0273 mmol/g) gases. HDTMA montmorillonites may be effective adsorbents for removing SO(2) and for its potential separation in the presence of CO and/or CH(4) molecules, which can be present in contaminated air.     

Adsorption and transport of arsenic(V) in experimental subsurface systems

The adsorption and transport of As(V) in a heterogeneous, iron oxide-containing soil was investigated in batch and column laboratory experiments. The As(V) adsorbed rapidly to the soil over the first 48 h, but continued to adsorb slowly over the next several weeks, clearly indicating the potential for rate-limited transport. The equilibrium As(V) adsorption isotherm was markedly nonlinear, further indicating the potential for nonideal transport. A model developed for the adsorption of As(V) to hydrous ferric oxide (HFO) was able to predict the pH-dependent adsorption of As(V) to the soil in batch experiments within 0.116 to 0.726 root mean square error (RMSE). Arsenic(V) was significantly retarded in column transport experiments. The column transport experiments were modeled using the one-dimensional advection-dispersion equation, considering both linear and nonlinear adsorption equilibrium. Although the nonlinear local equilibrium model (NLLE, RMSE = 0.273) predicted the data better than the linear local equilibrium model (LLE, RMSE = 0.317), As(V) breakthrough occurred more rapidly than predicted by either model due to adsorption nonequilibrium. However, due to the presence of an irreversible or slowly desorbing fraction, the peak aqueous As(V) concentration (0.624 mg L(-1)) and the total amount of As(V) recovered (44%) was lower than predicted based on the two equilibrium models (NLLE and LLE). For the conditions used in this study [1 mg L(-1) As(V), pH 4.5 and 9,0-0.25 mM PO4, 0.53-1.6 cm min(-1) pore water velocity], the effect on As(V) mobility and recovery increased in the order pH < pore water velocity < PO4.     

A study on oxidative degradation of polyacrylamide in wastewater with UV/FENTON/C4H4O62−

The degradation of polyacrylamide (PAM) in simulate wastewater was studied in UV/Fenton/C₄H₄O₆^2? system. The factors such as molecular ratio of H₂O₂/Fe²⁺/C₄H₄O₆^2?, pH, and the dosage of Fenton reagent that could affect the PAM degradation in the UV/Fenton/C₄H₄O₆^2? system were investigated. The experimental results showed that adding C₄H₄O₆^2? to UV/Fenton system could form photosensitive ferrous complexes, which led to higher degradation efficiency of PAM. The degradation rate of PAM could be up to 95.2% under the following conditions: the concentration of H₂O₂, Fe²⁺, and C₄H₄O₆^2? were 22.5, 2.25, and 2.25 mmol/L, respectively (i.e., molecular ratio of H₂O₂/Fe²⁺/C₄H₄O₆^2? was 10:1:1), the pH value was 3.0.     

Influence of biochar on nitrogen fractions in a coastal plain soil

Interest in the use of biochar from pyrolysis of biomass to sequester C and improve soil productivity has increased; however, variability in physical and chemical characteristics raises concerns about effects on soil processes. Of particular concern is the effect of biochar on soil N dynamics. The effect of biochar on N dynamics was evaluated in a Norfolk loamy sand with and without NHNO. High-temperature (HT) (≥500°C) and low-temperature (LT) (≤400°C) biochars from peanut hull ( L.), pecan shell ( Wangenh. K. Koch), poultry litter (), and switchgrass ( L.) and a fast pyrolysis hardwood biochar (450-600°C) were evaluated. Changes in inorganic, mineralizable, resistant, and recalcitrant N fractions were determined after a 127-d incubation that included four leaching events. After 127 d, little evidence of increased inorganic N retention was found for any biochar treatments. The mineralizable N fraction did not increase, indicating that biochar addition did not stimulate microbial biomass. Decreases in the resistant N fraction were associated with the high pH and high ash biochars. Unidentified losses of N were observed with HT pecan shell, HT peanut hull, and HT and LT poultry litter biochars that had high pH and ash contents. Volatilization of N as NH in the presence of these biochars was confirmed in a separate short-term laboratory experiment. The observed responses to different biochars illustrate the need to characterize biochar quality and match it to soil type and land use.     

Removal of basic dye (Astrazon Blue FGRL) using macroalga Caulerpa lentillifera

The macroalga Caulerpa lentillifera was found to have adsorption capacity for a basic dye, Astrazon Blue FGRL. For the whole range of concentrations employed in this work (20-1280 mgl(-1)), the adsorption reached equilibrium within the first hour. The kinetic data corresponded well with the pseudo second-order kinetic model where the rate constants decreased as initial dye concentrations increased. At low dye concentrations (20-80 mgl(-1)), an increase in the adsorbent dosage resulted in a higher removal percentage of the dye, but a lower amount of dye adsorbed per unit mass (q). The adsorption isotherm followed both the Langmuir and Freundlich models within the temperature range employed in this work (18-70 degrees C). The highest maximum adsorption capacity (q(m)) was obtained at 50 degrees C. The enthalpy of adsorption was estimated at 14.87 kJmol(-1) suggesting a chemical adsorption mechanism.