高原地区溶解氧浓度对A2／O工艺运行效果研究

针对我国低温地区的城市污水，开展了A2／O工工艺中试研究，考察溶解氧浓度对A2／O工工艺运行效果的影响。结果表明：采用A2／O工工艺并延长好氧池HRT，在系统水温为10℃-14℃的情况下可获得良好的污水处理效果。A2／O工工艺中好氧池末端的溶解氧浓度宜控制在2．8mg／L左右，此时的系统平均出水COD、氨氮、总氮和总磷浓度分别为40mg／L、3．8mg／L、13．0mg／L和0．7mg／L，平均COD、氨氮、总氮和总磷去除率分别为92．4％、83．8％、72．7％和87．1％。     

硫酸盐生物还原的限制性生态因子的影响研究

利用厌氧颗粒污泥对烟气中SO2吸收生成的硫酸盐或亚硫酸盐废水进行处理，考察起始SO4^2-质量浓度、初始COD／SO4^2-、初始pH、接种污泥质量、亚铁离子等限制性生态因子对硫酸盐还原的影响。结果表明：在起始SO4^2-质量浓度800mg／L，初始COD／SO4^2-为3．0，pH值为7．0，接种污泥质量为31．10gVSS／L，添加亚铁离子的条件下，进行半连续试验，硫酸根去除率可迭70％。表明在COD／SO4^2-较低的条件下，各生态因子综合作用下，硫酸盐还原可得较好效果。     

异烟酸-吡唑啉酮光度法测定地表水中氰化物的质量控制指标研究

通过对大量监测数据进行统计分析,获得异烟酸-吡唑啉酮光度法（HJ484—2009）测定水中氰化物质量控制评定指标。研究表明：样品浓度在0．05～0．3mg／L范围内时,建议控制室内相对标准偏差≤3％,室间相对标准偏差≤10％;样品浓度小于等于0．05mg／L时,建议控制相对偏差≤10％;样品浓度大于0．05mg／L时,...     

生物促生剂修复受污水体净化效能研究

对生物促生剂（Bio-energizer，BE）净化受污水体的效果进行了试验研究。结果表明：生物促生剂在低浓度时（小于1 ml／m^3），水体修复效果不明显；当浓度在3ml／m^3以上时，可以有效的加快水体中N、P类营养物的降解，可使NH4^＋ -N和TN分别由3．6—4．4mg／L和4．4—4．9mg／L降低至0．13-0．18 mg／L和0．39—1．06 mg／L，PO4^3- -P和TP分别由0．03-0．04mg／L和0．11—0．12mg／L降低至0．004-0．008mg／L和0．025-0．04mg／L。COD在试验过程中有上升的趋势。     

溶解氧对垃圾渗滤液强化预处理的影响研究

研究了二段式接触氧化工艺处理城市生活垃圾填埋渗滤液的强化预处理单元溶解氧变化对单元运行效果的影响。监测了0．2mg／L，0．4mg／L，0．6mg／L，0．8mg／L，1．0mg／L五个DO水平下，COD、NH3-N在0～30h内降解状况，降解曲线在较低的DO条件下，高效段较短，而DO越高，高效段越长。同时，对不同DO水平下C／N随时间的变化也进行了检测，为达到不同的C／N水平提供了工况选择上的参考。分析了降解曲线的特征及其工程应用的价值，提出了常规条件下该单元较优的溶解氧工况水平。     

厌氧氨氧化反应器的启动及运行

采用污泥混合接种的方法 ,成功地启动了实验室规模的厌氧氨氧化反应器 ,启动后含氨模拟废水运行的进水氨浓度和进水亚硝基氮浓度均为 2 0mmol/L ,氨氮、亚硝基氮和总氮的容积负荷率为 10 6 9mmol/L .d、12 2 6mmol/L .d和 394 5 5mg/L .d ,氨氮、亚硝基氮和总氮的去除率保持在 90 %、99%和 95 %以上。对运行条件研究表明 ,厌氧氨氧化反应的最适pH为 7～ 7 5 ,最适温度约在30± 1℃。厌氧氨氧化随亚硝酸盐浓度的升高而下降 ,氨的厌氧转化随COD浓度的增加也呈抑制型曲线 ,当COD浓度为 80 0±5 0mg/L时 ,厌氧氨氧化速率达到最大。     

城市污水处理厂剩余污泥中温厌氧消化处理研究

应用污水处理厂剩余污泥开展污泥中温厌氧消化实验，对一系列影响污泥厌氧消化反应的因素进行了考察。实验结果表明：由于污泥C／N值较低，单独消化非常困难，有机物分解率比较低，分解速度慢，气体发生量少。在35℃时，污泥投配率为7．5％～10％，基质的去除率可达到35．54％。37．62％，去除单位基质的产甲烷量为O．265～O.274m^3／kgCOD。     

SBR中好氧颗粒污泥的培养

采用竖式SBR作为反应器，利用城市污水处理厂剩余污泥作为接种污泥，通过不间断运行培养出好氧颗粒污泥。实验结果表明，采用非限量曝气模式好氧颗粒污泥降解模拟污水的效果较好，其COD去除率可达98％以上。曝气量对好氧颗粒污泥的形成和稳定具有重要影响，当气速为26．5m／h时，好氧颗粒污泥的性状和处理有机废水效果最佳。同时好氧颗粒污泥对pH值的变化不明显，当pH为5—8范围内，其COD去除率都可达到85％以上。但是未经驯化的好氧颗粒污泥对对硝基苯酚和对氯苯酚两种芳香类有机物较敏感，而对硝基苯酚对其毒性更大。当对硝基苯酚和。对氯苯酚浓度为10mg／L时，其COD去除率仅为42．5％和52％。     

酒精废水消化液预处理试验研究

高浓度酒精糟液经厌氧生物处理后排出的消化液COD浓度为4500—6000mg/L，SS浓度高这1500—2．600mg,／L，且由于微小沼气泡附着在厌氧污泥上，沉降性能很差，难以与消化液相分离，对后续处理十分不剁。本研兜采用预曝气．化学混凝沉淀组合工艺，对该消化液进行去除高浓度SS的顸处理试验，研究探讨了曝气时间、混凝剂种类和投加量对SS和COD去除效果的影响。试验结果表明，预曝气．化学混凝沉淀组合工艺对消化液SS的去除效果十分显著。当预曝气时间为6．0h，FeCl3投加量为100mg/L时，消化液的SS去除率75．4％，COD去除率24．3％，可为后续的好氧生物处理提供较为有利的水质和负荷条件。     

两种四环素类抗生素厌氧生物毒性试验研究

在35℃中温厌氧条件下，采用间歇试验法，通过测定甲烷累积产量，研究脱水土霉素和强力霉素两种四环素类物质的厌氧生物降解性，利用相对活性来判断两类物质对产甲烷菌的抑制程度。试验结果表明：脱水土霉素浓度低于200mg／L时产生轻度抑制，高于200mg/L产生中度抑制；强力霉素低于200mg／L时产生中度抑制，高于200mg／L时对产甲烷菌产生重度抑制，厌氧污泥活性很难恢复。     

SBR法处理啤酒废水DO对丝状菌污泥膨胀的影响

溶解氧(DO)浓度是影响丝状菌污泥膨胀最重要的因素之一。选用具有代表性的啤酒废水为处理对象,研究了SBR工艺中DO浓度对丝状菌污泥膨胀的影响。结果表明:高DO浓度(4～6.5mg/L)不会导致丝状菌污泥膨胀;低DO浓度能引起丝状菌污泥膨胀,当DO浓度降低至0.4mg/L时,SVI升高到210mL/g,会导致污泥膨胀发生。低DO浓度下污泥膨胀发生后,在较高的DO浓度条件下运行一定的周期数后,污泥膨胀能得到有效控制,使污泥沉降性能恢复到正常水平。     

无污泥化生物技术在真丝染色综合废水处理中的研究及应用

本文主要对真丝染色综合废水Ａ／Ｏ处理中所产生的污泥进行无污泥化生物处理的研究,并把技术运用在日处理９００ｔ／ｄ的综合废水生化处理装置上,设施经四年连续运行表明：出水ｐＨ＝７． ３６,ＳＳ＝４８ｍｇ／１,ＣＯＤｃｒ＝９５ｍｇ／１,ＢＯＤ５＝３８ｍｇ／１,ＮＨ３－Ｎ＝１８ ．８ｍｇ／１,出水水质指标全部达到国家规定的排放标准,该技术不仅解决了污泥的难治理问题,而且利用生物技术彻底解决了污泥的二次污染问题,还节约了可观的运行费用和投资费用,并提高了Ａ／Ｏ的处理效果。     

大连石化污水处理场二期活性污泥培养驯化的实践

A/O生化池首次启动时的生物培养至关重要。大连石化公司污水处理场二期工程采用生物接种、微生物的培养和驯化,得出:开始接种后,A、B两个系列A/O池的污泥浓度呈连续上升的趋势,污泥浓度增加到2000～3000mg/L,可以进入培养驯化阶段;控制好A/O池的pH值、碱度、无机盐、氮源、泥龄、污泥指数等运行参数,可以较好地调整控制微生物的生物氧化方向,尽快达到驯化目的。     

Respirometry-based evaluation of the fate and possible effects of antifreeze on activated sludge

This paper focuses on environmental concerns regarding used antifreeze. It shows the results of laboratory respirometric tests conducted to evaluate the potential impact of antifreeze on activated sludge. In this first step of the study, only the components of virgin antifreeze were addressed, i.e. ethylene glycol, and antifoaming and corrosion inhibitory substances. The plateau resulting from oxygen uptake rate measurements of mixed liquor taken at the end of an aeration tank is used as a reference to evaluate the response of biomass to pulse injection of increasing dosages of new antifreeze, compared to that of formaldehyde, a known toxic compound. While 200 mg/L of formaldehyde steadily decreased the biomass activity (7 mg O2/Lh), there were no toxicity effects for doses up to 5000 mg/L of ethylene glycol from new antifreeze coolant (23 mg O2/Lh, compared to the initial 15 mg O2/Lh for the mixed liquor). It is estimated that ethylene glycol concentration in municipal wastewaters should be several order of magnitude lower then the 1000 mg/L shown to be tolerated by the biomass in this work, but at the present stage, the research does not provide enough information to recommend a definitive management scheme for antifreeze discharge. Many other management issues for used antifreeze must be addressed in future studies before any decision on tolerating sewer discharge in Mexico, as a transitory management option that will conciliate the actual practices with legality, can be made.     

污泥土地利用中重金属铜污染地下水的潜在风险研究

本研究旨在通过土柱淋溶实验来研究堆肥污泥土地利用后重金属铜的溶出性,以及对地下水的影响。结果表明:与去离子水相比,模拟酸雨(pH=4.5)会使土壤中Cu的淋溶强度增加,并更能促使其向下迁移。经长期淋溶后发现,淋出液中铜的浓度呈现有起伏的递减趋势,最高峰浓度达到0.0702mg/L,远低于地下水Ⅲ类标准(1.0mg/L),污泥土地利用后Cu对地下水的污染风险较小。     

Aerobic treatment of palm oil mill effluent

In this study treatment of palm oil mill effluent (POME) was investigated using aerobic oxidation based on an activated sludge process. The effects of sludge volume index, scum index and mixed liquor suspended solids during the acclimatizing phase and biomass build-up phase were investigated in order to ascertain the reactor stability. The efficiency of the activated sludge process was evaluated by treating anaerobically digested and diluted raw POME obtained from Golden Hope Plantations, Malaysia. The treatment of POME was carried out at a fixed biomass concentration of 3900+/-200mg/L, whereas the corresponding sludge volume index was found to be around 105+/-5mL/g. The initial studies on the efficiency of the activated sludge reactor were carried out using diluted raw POME for varying the hydraulic retention time, viz: 18, 24, 30 and 36h and influent COD concentration, viz: 1000, 2000, 3000, 4000 and 5000mg/L, respectively. The results showed that at the end of 36h of hydraulic retention time for the above said influent COD, the COD removal efficiencies were found to be 83%, 72%, 64%, 54% and 42% whereas at 24h hydraulic retention time they were 57%, 45%, 38%, 30% and 27%, respectively. The effectiveness of aerobic oxidation was also compared between anaerobically digested and diluted raw POME having corresponding CODs of 3908 and 3925mg/L, for varying hydraulic retention time, viz: 18, 24, 30, 36, 42, 48, 54 and 60h. The dissolved oxygen concentration and pH in the activated sludge reactor were found to be 1.8-2.2mg/L and 7-8.5, respectively. The scum index was found to rise from 0.5% to 1.9% during the acclimatizing phase and biomass build-up phase.     

Sorption and biodegradability of sludge bacterial extracellular polymers in soil and their influence on soil copper behavior

Bacterial extracellular polymers (BEP) affect the translocation and fate of organic and inorganic pollutants in terrestrial and aquatic ecosystems. In this study, BEP from activated sludge was compared with sludge dissolved organic matter (DOM) in terms of behavior and effects on the mobilization and bioavailability of Cu in a well-aged Cu-contaminated orchard sandy loam. Addition of sludge BEP (10-200 mg dissolved organic carbon [DOC] L(-1)) to the soil resulted in 1.6- to 12.8-fold-higher soil soluble Cu concentration over the control and 1.3- to 2.2-fold over sludge DOM of the same concentration. Consequently, the Cu uptake by the ryegrass (Lolium perenne L., cv. Target) grown in the soil was increased by 31% due to interval watering of 100 mg DOC L(-1) of sludge BEP solution in a 35-d period. The influence of sludge BEP on mobilizing soil Cu could be maintained as long as 60 d or more, depending on BEP biodegradation status. The findings that sludge BEP promoted Cu mobilization and bioavailability could be attributed to less adsorption of BEP by soil, slow degradation, and higher affinity with Cu. For example, after 3 wk of aerobic incubation, the soluble Cu present in the sludge DOM-treated soil was reduced to about the level of the control, while the concentration of soluble Cu in BEP-treated soil was 6.2 times higher than that in the control. Therefore, sludge BEP could act as a facilitated-transport carrier of Cu. The environmental risk of Cu should receive much attention if BEP is incorporated into soils.     

生物氧化法处理高浓度含氨、含氰废水

通过对用普通活性污泥法法处理高浓度含氨、含氰废水的可行性分析,总结了装置改进后,在工艺流程;微生物的培养及驯化;运行参数的选择等方面的运行情况。提出适宜的浓度范围是: NH3—N<500 mg/l;COD<800 mg/L;氰化物<10 mg/L;镍<10 mg/L。结论为:① 用生物氧化法处理高浓度含氨、含氰废水,不仅可行,而且处理效果比较好;② 该装置的水质适应性比较好,对低浓度的毒性物质有降解作用,如氰化物、镍等;③ 此工艺产生的污泥量比较少。     

高效降解环己酮红球菌JDM-3-12的分离及其系统发育分析

从岳阳巴陵石化公司环己酮生产车间总出水口的污泥中筛选到一株环己酮降解菌株,菌号为JDM-3-12;该菌能以环己酮为唯一碳源且能忍受5000 mg/L的环己酮,当环己酮的质量浓度为2000 mg/L时,在温度为30℃,转速为150 r/m in,pH=7的条件下,72小时内该菌株对环己酮的降解率达到97.91%。通过形态观察、生理生化特征检测和基于16S rRNA基因序列的系统发育分析,初步鉴定其为赤红球菌(Rhodococcus ruber)中的一个菌株,该菌最适生长温度为35℃,最适生长pH 7。     

MBBR工艺在生活污水处理装置完善项目中的应用

文章应用MBBR(流动床生物膜反应器)工艺对某石化公司生活污水处理装置进行改造,并研究影响该工艺高效脱氮的主要因素,即pH值、DO含量和污泥回流比。结果表明:实际运行中,pH值控制在7.5、DO在1～4mg/L、污泥回流比R≤3,能取得较好的脱氮效果,将氨氮降至3mg/L以下,同时,将污泥浓度维持在5～8g/L,还可在短时间内实现CODCr高去除率。实践证明,MBBR工艺在生活污水完善项目中的应用,能够有效降低污水中污染物含量,为后续深度处理系统的稳定运行提供可靠保障。