Utilization of waste product (tamarind seeds) for the removal of Cr(VI) from aqueous solutions: Equilibrium, kinetics, and regeneration studies

In the present study, an adsorbent was prepared from tamarind seeds and used after activation for the removal of Cr(VI) from aqueous solutions. The tamarind seeds were activated by treating them with concentrated sulfuric acid (98% w/w) at a temperature of 150 °C. The adsorption of Cr(VI) was found to be maximum at low values of initial pH in the range of 1–3. The adsorption process of Cr(VI) was tested with Langmuir, Freundlich, Redlich–Peterson, Koble–Corrigan, Tempkin, Dubinin–Radushkevich and Generalized isotherm models. Application of the Langmuir isotherm to the system yielded a maximum adsorption capacity of 29.7 mg/g at an equilibrium pH value ranging from 1.12 to 1.46. The adsorption process followed second-order kinetics and the corresponding rate constants obtained were 2.605 × 10⁻³, 0.818 × 10⁻³, 0.557 × 10⁻³ and 0.811 × 10⁻³ g/mg min⁻¹ for 50, 200, 300 and 400 mg/L of initial Cr(VI) concentration, respectively. The regenerated activated tamarind seeds showed more than 95% Cr(VI) removal of that obtained using the fresh activated tamarind seeds. A feasible solution is proposed for the disposal of the contaminants (acid and base solutions) containing high concentrations of Cr(VI) obtained during the regeneration (desorption) process.     

Comparison of biosorbents with inorganic sorbents for removing copper(II) from aqueous solutions

In comparison with several other reported inorganic sorbents, Camellia tree leaf and primary sludge obtained from a settling tank as a pretreatment to the activated sludge system in a Hong Kong sewage treatment plant were evaluated for removing Cu(II) from aqueous solutions. Experimental data were modeled by the Langmuir isotherm equation to estimate the maximum sorption capacity (q_max). Results show that, at pH 5.6, biosorbents, Camellia tree leaf and primary sludge in particular, exert higher sorption capacities (q_max > 40 mg g⁻¹) than inorganic sorbents, Na-montmorillonite (q_max = 33.3 mg g⁻¹), fly ash (q_max = 18.8 mg g⁻¹), and goethite powder (10.3 mg g⁻¹). Furthermore, a pseudo second-order kinetic model was found to properly describe the experimental data for both bio- and inorganic sorbents. Sorption of Cu(II) on the Camellia tree leaf and primary sludge were much faster than that on the inorganic sorbents. In addition, desorption tests revealed that the desorption capacities of the two biomaterials are higher than the other selected materials; and much more Cu(II) can be retrieved from the Cu(II)-loaded biosorbents. Finally, increasing solution pH was found to greatly increase q_max and accelerate sorption processes.     

Biosorption of Cu and Zn from aqueous solutions by dried marine green macroalga Chaetomorpha linum

The biosorption of the heavy metals Cu²⁺ and Zn²⁺ by dried marine green macroalga (Chaetomorpha linum) was investigated. The biosorption capacities of the dried alga for copper and zinc were studied at different solution pH values (2–6), different algal particle sizes (100–800 μm) and different initial metal solution concentrations (0.5–10 mM). An optimum pH value of 5 was found suitable for both metal ions biosorption for both metal ions. At the optimum particle size (100–315 μm), biosorbent dosage (20 g/l) and initial solution pH (pH 5), the dried alga produced maximum copper and zinc uptakes values (q_max) of 1.46 and 1.97 mmol/g respectively (according to the Langmuir model). The kinetic data obtained at different initial metal concentrations indicated that the biosorption rate was fast and most of the process was completed within 120 min. This study illustrated an alternative technique for the management of unwanted biological materials using processed algal material. C. linum is one of the fast-growing marine algae in the lake of Tunis and could be utilized as a biosorbent for the treatment of Cu²⁺ and Zn²⁺ contaminated wastewater streams.     

Unexpected difference in phenol sorption on PTMA- and BTMA-bentonite

The comparison of phenol sorption on phenyltrimethylammonium (PTMA)- and benzyltrimethylammonium (BTMA)-bentonite shows a clear difference as far as phenol sorption isotherms are concerned. For PTMA-bentonite the sorption isotherm is of a straight-line character which results from simple partitioning of phenol between the aqueous and organic phases sorbed on the bentonite surface. For BTMA-bentonite the isotherm has a convex shape, characteristic of physicochemical sorption.For the first time a three-parametric model, including the dissociation constant of phenol pK_a, distribution constant of phenol Kd_phen and phenolate anion Kd_phen⁻ between the aqueous phase and the bentonite phases is used for the evaluation of phenol sorption on organoclays with pH change. The model shows that the values of Kd_phen are higher than those of Kd_phen⁻ for all investigated initial phenol concentrations.The inspection of the FTIR spectrum of BTMA-bentonite loaded with phenol in the regions 1300–1600 and 1620–1680 cm⁻¹ shows the features of π–π electron interaction between the benzene rings of phenol and the BTMA cation together with the phenol–water hydrogen bond strengthened by this interaction.     

Monitoring of the microbial community composition in saline aquifers during CO2 storage by fluorescence in situ hybridisation

This study reveals the first analyses of the composition and activity of the microbial community of a saline CO₂ storage aquifer. Microbial monitoring during CO₂ injection has been reported. By using fluorescence in situ hybridisation (FISH), we have shown that the microbial community was strongly influenced by the CO₂ injection. Before CO₂ arrival, up to 6 × 10⁶ cells ml⁻¹ were detected by DAPI staining at a depth of 647 m below the surface. The microbial community was dominated by the domain Bacteria that represented approximately 60% to 90% of the total cell number, with Proteobacteria and Firmicutes as the most abundant phyla comprising up to 47% and 45% of the entire population, respectively. Both the total cell counts as well as the counts of the specific physiological groups revealed quantitative and qualitative changes after CO₂ arrival. Our study revealed temporal outcompetition of sulphate-reducing bacteria by methanogenic archaea. In addition, an enhanced activity of the microbial population after five months CO₂ storage indicated that the bacterial community was able to adapt to the extreme conditions of the deep biosphere and to the extreme changes of these atypical conditions.     

Equilibrium studies of copper ion adsorption onto palm kernel fibre

The equilibrium sorption of copper ions from aqueous solution using a new adsorbent, palm kernel fibre, has been studied. Palm kernel fibre is obtained in large amounts as a waste product of palm oil production. Batch equilibrium studies were carried out and system variables such as solution pH, sorbent dose, and sorption temperature were varied. The equilibrium sorption data was then analyzed using the Langmuir, Freundlich, Dubinin–Radushkevich (D–R) and Temkin isotherms. The fit of these isotherm models to the equilibrium sorption data was determined, using the linear coefficient of determination, r², and the non-linear Chi-square, χ² error analysis.The results revealed that sorption was pH dependent and increased with increasing solution pH above the pH_PZC of the palm kernel fibre with an optimum dose of 10 g/dm³. The equilibrium data were found to fit the Langmuir isotherm model best, with a monolayer capacity of 3.17 × 10^?4 mol/g at 339 K. The sorption equilibrium constant, K_a, increased with increasing temperature, indicating that bond strength between sorbate and sorbent increased with temperature and sorption was endothermic. This was confirmed by the increase in the values of the Temkin isotherm constant, B₁, with increasing temperature. The Dubinin–Radushkevich (D–R) isotherm parameter, free energy, E, was in the range of 15.7–16.7 kJ/mol suggesting that the sorption mechanism was ion exchange. Desorption studies showed that a high percentage of the copper was desorbed from the adsorbent using acid solutions (HCl, HNO₃ and CH₃COOH) and the desorption percentage increased with acid concentration. The thermodynamics of the copper ions/palm kernel fibre system indicate that the process is spontaneous and endothermic.     

Batch sorption dynamics and equilibrium for the removal of lead ions from aqueous phase using activated carbon developed from coffee residue activated with zinc chloride

Lignocellulosic materials are good precursors for the production of activated carbon. In this work, coffee residue has been used as raw material in the preparation of powder activated carbon by the method of chemical activation with zinc chloride for the sorption of Pb(II) from dilute aqueous solutions.The influence of impregnation ratio (ZnCl₂/coffee residue) on the physical and chemical properties of the prepared carbons was studied in order to optimize this parameter. The optimum experimental condition for preparing predominantly microporous activated carbons with high pore surface area (890 m²/g) and micropore volume (0.772 cm³/g) is an impregnation ratio of 100%. The developed activated carbon shows substantial capability to sorb lead(II) ions from aqueous solutions and for relative impregnation ratios of 75 and 100%, the maximum uptake is practically the same. Thus, 75% represents the optimal impregnation ratio.Batch experiments were conducted to study the effects of the main parameters such as contact time, initial concentration of Pb(II), solution pH, ionic strength and temperature. The maximum uptake of lead(II) at 25 °C was about 63 mg/g of adsorbent at pH 5.8, initial Pb(II) concentration of 10 mg/L, agitation speed of 200 rpm and ionic strength of 0.005 M. The kinetic data were fitted to the models of pseudo-first order and pseudo-second order, and follow closely the pseudo-second order model. Equilibrium sorption isotherms of Pb(II) were analyzed by the Langmuir, Freundlich and Temkin isotherm models. The Freundlich model gives a better fit than the others.Results from this study suggest that activated carbon produced from coffee residue is an effective adsorbent for the removal of lead from aqueous solutions and that ZnCl₂ is a suitable activating agent for the preparation of high-porosity carbons.     

Cellulose-based anion exchanger with tertiary amine functionality for the extraction of arsenic(V) from aqueous media

A novel cellulose-based anion exchanger (Cell-AE) with tertiary amine functionality was synthesized by graft polymerization reaction of cellulose and glycidyl methacrylate using N,N′-methylene-bis-acrylamide as a crosslinker and benzoyl peroxide as an initiator, followed by dimethylamine (amination) and acid (HCl) treatment. The chemical modification was confirmed by infrared spectroscopy and CHN analysis. The anion exchanger was used in batch processes to study AS(V) adsorption in solutions. The operating variables studied were pH, contact time, initial As(V) concentration, sorbent mass, and ionic strength. The process was affected by solution pH with an optimum adsorption occurring at pH 6.0. Adsorption equilibrium was achieved within 1 h. Increasing ionic strength of solution negatively affected the arsenic uptake. The adsorption process performed more than 99.0% of As(V) removal from an initial concentration of 25.0 mg/L. The process of adsorption followed pseudo-second-order kinetics. The adsorption equilibrium isotherm data were analyzed using the Langmuir, Freundlich, Redlich–Peterson and Langmuir–Freundlich equations. The Langmuir–Freundlich isotherm described the adsorption data over the concentration range 25–400 mg/L. The adsorption mechanism appears to be a ligand-exchange process. A simulated groundwater sample was treated with Cell-AE to demonstrate its efficiency in removing As(V). The adsorbed As(V) ions were desorbed effectively by a 0.1 M NaOH solution.     

Model prediction on the rise of pCO2 in uniform flows by leakage of CO2 purposefully stored under the seabed

A numerical study was conducted to predict pCO₂ change in the ocean on a continental shelf by the leakage of CO₂, which is originally stored in the aquifer under the seabed, in the case that a large fault connects the CO₂ reservoir and the seabed by an earthquake or other diastrophism. The leakage rate was set to be 6.025 × 10⁻⁴ kg/m²/sec from 2 m × 100 m fault band, which corresponds to 3800 t-CO₂/year, referring to the monitored seepage rate from an existing EOR field. The target space in this study was limited to the ocean above the seabed, the depth of which was 200 or 500 m. The computational domain was idealistically rectangular with the seabed fault-band perpendicular to the uniform flow. The CO₂ takes a form of bubbles or droplets, depending on the depth of water, and their behaviour and dissolution were numerically simulated during their rise in seawater flow. The advection–diffusion of dissolved CO₂ was also simulated. As a result, it was suggested that the leaked CO₂ droplets/bubbles all dissolve in the seawater before spouting up to the atmosphere, and that the increase in pCO₂ in the seawater was smaller than 500 μ atm.     

Application of a chemically modified green macro alga as a biosorbent for phenol removal

Phenol and substituted phenols are toxic organic pollutants present in tannery waste streams. Environmental legislation defines the maximum discharge limit to be 5–50 ppm of total phenols in sewers. Thus the efforts to develop new efficient methods to remove phenolic compounds from wastewater are of primary concern. The present work aims at the use of a modified green macro alga (Caulerpa scalpelliformis) as a biosorbent for the removal of phenolic compounds from the post-tanning sectional stream. The effects of initial phenol concentration, contact time, temperature and initial pH of the solution on the biosorption potential of macro algal biomass have been investigated. Biosorption of phenol by modified green macro algae is best described by the Langmuir adsorption isotherm model. Biosorption kinetics of phenol onto modified green macro algal biomass were best described by a pseudo second order model. The maximum uptake capacity was found to be 20 mg of phenol per gram of green macro algae. A Boyd plot confirmed the external mass transfer as the slowest step involved in the biosorption process. The average effective diffusion coefficient was found to be 1.44 × 10⁻⁹ cm²/s. Thermodynamic studies confirmed the biosorption process to be exothermic.     

Assessment of the Microbiological Quality of Clarias gariepinus Exposed to an Industrial Effluent in Nigeria

The microbiological impact of a detergent and soap industries effluent on Clarias gariepinus was assessed under laboratory conditions. The heterotrophic bacterial count obtained from fish surfaces ranged from 1.2 × 10²−2.0 × 10²cfu/ml amongst the control, while values of 4.8× 10⁶−8.6 × 10⁶ cfu/ml were obtained for the experimental fish exposed to the industrial effluent (0.025 ppm). The fungal count for the controls ranged from 1.2× 10²−1.2 × 10³ cfu/ml; while a range of 1.0 × 10⁶−2.0 × 10⁶ was obtained for the fish exposed to the industrial effluent. While twelve bacterial species were isolated from the fish exposed to the industrial effluent, only two were isolated from the parts of the control fish used in the study. The bacterial species are those in the genera Staphylococcus, Proteus, Streptococcus, Micrococcus, Bacillus, Pseudomonas, Serratia, Enterobacter, and Escherichia. The fungal isolates include Saccharomyces, Aspergillus, Rhodosporium, Candida, Alternaria, and Fusarium. The resistance of the bacterial isolates to the commonly used antibiotics showed that 100% were resistant to Augmentin, Amoxycillin and Cloxacillin, 85.71% to Tetracycline, 80.95% to Cotrimoxazole, 71.43% to Erythromycin, 33.33% to Chloramphenicol, and 28.57% to Gentamicin. Among the eight antibiotics tested, five patterns of multiple drug resistance were obtained, with the number of the antibiotics ranging from 4–8. The public health implications of these observations are discussed.     

Response to environmental flows in the Lower Tarim River, Xinjiang, China: an ecological interpretation of water-table dynamics

Increased water-dependent development and utilization have led to significant environmental and hydrological degradation of the Tarim River in western China and its dependent ecosystems. Between the 1950s and 1970s, 350 km of the lower reaches were drained and between 1960 and 1980 the water-table fell from between −2 and −3 m to between −8 and −10 m. Subsequently, riparian ecosystems were seriously degraded. In 2000, the Chinese government launched a program to restore the lower reaches of the river. Four environmental flows of 1034×10⁶ m³ were released from 2000 to 2002. This paper interprets and discusses the ecological significance of changes following the releases and identifies the relationship between water-table dynamics and vegetation responses. Short-term objectives for river restoration are proposed with possible monitoring parameters suggested.     

Sorption isotherm studies of Cd(II) ions using living cells of the marine microalga Tetraselmis suecica (Kylin) Butch

The present work reports the use of living cells of the marine microalga Tetraselmis suecica for the biosorption of cadmium ions. For a better understanding of the biosorption characteristics, three fractions of removed cadmium (total, bioadsorbed and intracellular) were measured in the cells after 24 and 72 h of exposure to different initial cadmium concentrations (0.6–45 mg L^?1). Both the Langmuir and Freundlich models were suitable for describing the sorption of cadmium ions by this microalga. The maximum sorption capacity was estimated to be 40.22 mg Cd g^?1 after 72 h using the Langmuir sorption model. In the lower cadmium concentrations, metal removed intracellularly was higher than that removed on the microalgal cell surface. Therefore, the intracellular fraction contributed more to the total removed cadmium than the fraction bioadsorbed to the cellular surface. The results showed that the cadmium removal capacity using living biomass could be much more effective than with non-living biomass due to the intracellular bioaccumulation. According to the microorganism selected and its tolerance to the toxic effect of the metal, the cadmium content in the intracellular fraction can become very significant, just like it happened with Tetraselmis.     

Zeolite formation from coal fly ash and heavy metal ion removal characteristics of thus-obtained Zeolite X in multi-metal systems

Zeolitic materials have been prepared from coal fly ash as well as from a SiO₂–Al₂O₃ system upon NaOH fusion treatment, followed by subsequent hydrothermal processing at various NaOH concentrations and reaction times. During the preparation process, the starting material initially decomposed to an amorphous form, and the nucleation process of the zeolite began. The carbon content of the starting material influenced the formation of the zeolite by providing an active surface for nucleation. Zeolite A (Na-A) was transformed into zeolite X (Na-X) with increasing NaOH concentration and reaction time. The adsorption isotherms of the obtained Na-X based on the characteristics required to remove heavy ions such as Ni²⁺, Cu²⁺, Cd²⁺ and Pb²⁺ were examined in multi-metal systems. Thus obtained experimental data suggests that the Langmuir and Freundlich models are more accurate compared to the Dubinin–Kaganer–Radushkevich (DKR) model. However, the sorption energy obtained from the DKR model was helpful in elucidating the mechanism of the sorption process. Further, in going from a single- to multi-metal system, the degree of fitting for the Freundlich model compared with the Langmuir model was favored due to its basic assumption of a heterogeneity factor. The Extended-Langmuir model may be used in multi-metal systems, but gives a lower value for equilibrium sorption compared with the Langmuir model.     

Growth and macronutrient removal of water hyacinth in a small secondary sewage treatment plant

Studies have been made of the growth characteristics of water hyacinth, Eichhornia crassipes (Mart.) Solms, and its ability to remove N, P and K, in a secondary settling pond of a small secondary sewage treatment plant serving both the academic and residential blocks of the Swire Marine Laboratory, University of Hong Kong. The treatment plant consists of, in series, a primary settling tank, a trickling filter compartment and a secondary settling pond from which part of the treated wastewater is recycled to the primary settling tank while the remaining effluent (1 to 2 m³ daily) mixes with and hence is diluted by the outflowing seawater from the aquarium system of the Swire Marine Laboratory before discharge to the sea. Samples of wastewater have been taken regularly from the primary sedimentation pond, the outflow of the trickling filter, the secondary settling pond and the effluent of the treatment plant (before mixing with aquarium outflow) since January, 1992. Physical, chemical and biological characteristics of the samples have been determined and are typical of secondary effluents, with a mean pH of about 7.5, total solids 1200 mg L⁻¹, suspended solids 45 mg L⁻¹, conductivity 2000 μS cm⁻¹, salinity 1 ppt, dissolved oxygen 2 mg L⁻¹, BOD₅ 45 mg L⁻¹, Kjeldahl-N 30 mg L⁻¹, NH₄,-N 25 mg L⁻¹, NO₃-N 4 mg L⁻¹, total P 10 mg L⁻¹, K 35 mg L⁻¹ and total coliforms of less than 10⁵ colonies 100 ml⁻¹.Water hyacinth plants have been stocked in the secondary settling pond as an integral part of the treatment plant so as to improve the quality of, as well as to retrieving and recycling nutrient elements from, the wastewater. The plants are periodically harvested to maintain an active growing crop. The growth rate, standing crop biomass, tissue nutrient composition, nutrient storage and accumulation rate of two growth cycles, one from February 25 to March 18 (mean temperature 17.6°C) and the other from 22 April to 12 May (24.8°C) are reported. The water hyacinth assumed a relatively high standing crop biomass of 10 kg m⁻² (5 to 6 t DM ha⁻¹), and growth rates of 48 and 225 g m⁻² day⁻¹, respectively, for the first and second growth period. Nutrient storage capacities were relatively high, at about 20, 7.5 and 16.5 g m⁻² for N, P and K, respectively. The nutrient composition was very high, reaching 5.42% for N, 1.97 for P, and 4.57 for K. Both the stem and lamina accumulated high levels of N, while the petiole had the highest level of P and K. Apart from nutrient removal, the water hyacinth also helped to decrease the suspended solids, BOD₅ value and total coliforms of the wastewater.It is concluded that water hyacinth improves the quality of wastewater in such small-scale sewage treatment plants and it is recommended that frequent harvests of water hyacinth would increase the treatment efficiency, especially during the active growing season with high temperatures coupled with intense solar radiation.     

Growth and fecundity of earthworms: <Emphasis Type="Italic">Perionyx excavatus</Emphasis> and <Emphasis Type="Italic">Perionyx sansibaricus</Emphasis> in cattle waste solids

Epigeic earthworms (Oligochaeta) have been appeared as key organisms to convert organic waste resources into value-added products, i.e., vermicompost and worm biomass. The assessment of reproduction potential of composting earthworm may be beneficial for large-scale earthworm production. Although, the waste minimizing potential of Perionyx excavatus and Perionyx sansibaricus is well proved, but little information is available about their fecundity rate. In this study, the efforts have been made to explore the growth and reproduction biology of P. excavatus and P. sansibaricus, using cattle waste solid as culture substrate, under laboratory conditions. Earthworms were weighed weekly and number of cocoons produced per week assessed. Biomass productions, fecundity, maturation, natality all were significantly different between P. excavatus and P. sansibaricus. The highest mean individual biomass was 767.7 ± 18.4 mg and 612.6 ± 20.6 mg, respectively in P. sansibaricus and P. excavatus. However, the highest cocoon numbers occurred in P. excavatus (492.3 ± 13.6), significantly higher than P. sansibaricus (269.6 ± 17.1). Fecundity was slightly different in both species: 1.38 ± 0.77 cocoons adult worm⁻¹ week⁻¹ (P. excavatus) and 1.58 ± 0.74 cocoons adult worm⁻¹ week⁻¹ (P. sansibaricus). The hatchling success rate (%) was highest in P. excavatus. Overall natality (juveniles adult⁻¹ week⁻¹) was highest in P. sansibaricus (1.52) than P. excavatus (1.26), which suggests that P. sansibaricus may be a better candidate for rapid propagation of earthworms in cattle waste solid.     

Platinum (IV) recovery from chloride solution by functionalized acrylic copolymers

Two acrylic adsorbents with different morphological structures and bearing amidoethylenamine and thiol groups were obtained and used for platinum sorption from chloride solution by the batch method. Physico-chemical parameters that influence adsorption such as initial Pt(IV) concentration, stirring time, pH, and adsorbent amount were investigated. The thermodynamic parameters of Pt(IV) sorption on the synthesized adsorbent were also evaluated based on Langmuir and Freundlich isotherms. Thermodynamic parameters estimated from Langmuir constants indicated that the adsorption is spontaneous, exothermic and there is a disordered state at the molecular level. The models used to analyze the sorption rate led to the conclusion that the most important step in the sorption of Pt(IV) could be both particle diffusion and chemical reaction of [PtCl₆]⁻ with amine functional groups. Thus, both the ion exchange and complex formation mechanisms can occur via nitrogen atoms in the recovery of Pt(IV) on the studied adsorbent.     

Biosorption of heavy metals by activated sludge and their desorption characteristics

The biosorption of different metals (Cu2+, Cd2+, Zn2+, Ni2+ and Pb2+) was investigated using activated sludge. The optimum pH was 4 for Cd, Cu and Pb sorption and 5 for Ni and Zn. Biomass metal uptake clearly competed with protons present in the aqueous medium, making pH an important variable in the process. Protons consumed by biomass in control tests versus protons exchange in biosorption tests confirmed a maximum exchange between metal cations and protons at pH 2. The study of the influence of biomass concentration revealed that the amount of protons released from biomass increased with biomass concentration. This would confirm the hypothesis of ion exchange between both types of ions. The application of the Langmuir and Freundlich models showed a better fitting of experimental data to the first model. The maximum sorption uptake of the studied metals by the activated sludge showed the following decreasing order: Pb>Cu>CdZn>Ni. Desorption experiments showed that HCl was a good eluent for the five metals tested, particularly at low pH values (1 and 2). At pH 3 or 4 the desorption yield was significantly lower. However, its use did not allow the reuse of biomass in subsequent loading and unloading cycles. EDTA was also a good desorption agent, achieving the total recovery for the five metals tested at a concentration of 1mM, with the advantage that biomass could be reused for three sorption-desorption cycles.     

Effect of selected and non-selected urban waste compost on the initial growth of corn

Brazil produces approximately 242,000 t of waste per day, 76% of it being dumped outdoors and only 0.9% recycled, including composting, which is an alternative still little known in Brazil. In search of a better destination for residues produced by domestic activities, composting stands as a feasible alternative. Organic compost from waste may be used for various purposes, among which are soil recovery, commercial production, pastures, lawns and reforestry and agriculture. However, the quality of the compost determines the growth and the development of plants. The effect of compost made from urban waste on corn plant (Zea mays L.) growth was investigated. Two types of compost were used: the selected compost (SC), produced from organic waste selectively collected; and the non-selected compost (NSC), taken from a 15-year-old cell from the Canabrava land-fill, located in Salvador, Bahia, Brazil (altitude 51 m, 12°22′–13°08′S, 38°08′–38°47′W). Corn was seeded in polyethylene pots, with soil-compost mixing substrate in the proportion of 0, 15, 30, 45 and 60 t ha⁻¹ equivalent doses. Chemical analyses of the compost and growth properties of the plant like chlorophyll content; height and stem diameter; aerial and radicular dry biomasses, were used to evaluate compost quality. Plants cultivated with SC presented a superior gain, being of 52.5% in stem diameter, 71.1 and 81.2% in root and stem biomasses, respectively. Chlorophyl content alterations were observed in plants from treatments using 30 t compost ha⁻¹ dose onwards. Conventional and multivariate statistical methods were used to evaluate these results. The beneficial action of organic compost in plant growth was confirmed with this research.     

Fly ash for the treatment of Zn(II) rich effluents

Summary The ability of fly ash to remove Zn(II) from water by adsorption has been tested at different concentrations, temperatures and pH of the solution. It was found that low adsorbate concentration, small particle size of adsorbent and higher temperature favoured the removal of Zn(II) from aqueous solution. The Langmuir isotherm was used to represent the equilibrium data at different temperatures. The apparent heat of adsorption has been found to be 17.325 Kcal mol^–1, which indicates the process to be endothermic. The uptake of Zn(II) is diffusion controlled and the mass transfer coefficient is 3.56 × 10^–5 cm s ^–1.The maximum removal was noted at pH 7.5. Dr V.N. Singh is Professor and Head of the Department of Applied Chemistry, Dr A.K. and Prof. D.P. Singh are members of the Department of Mining Engineering; all are situated in the Institute of Technology at Banaras Hindu University.