EXAMPLES OF LANDFILL-GENERATED PLUMES IN LOW-RELIEF AREAS,SOUTHEAST FLORIDA1

ABSTRACT: Areas of low topographic relief have low water-table gradients and make the direction of movement of contaminants from land fills in the ground water difficult to predict from regional gradients alone. The landfill, nearby free-flowing ditches or canals, variations in hydraulic conductivity, and the influence of nearby pumping wells can all affect the direction of flow. In low-gradient areas the concepts of “upgradient” and “downgradient” are less useful in planning the location of monitoring wells than in areas of higher relief. Low-relief areas also may be affected by the discharge of mineralized water from deeper aquifers, naturally or through irrigation, which can mask geochemical surveys intended to detect landfill leachate. Examples of effects of low topographic relief are noted in southeast Florida where water-table gradients are 7×10^?-⁴ to 5×10^?-⁴ feet per foot. Water-table mounding beneath the landfill and the drainage effects of nearby ditches and well have created multiple leachate plumes in Stuart where one plume migrated in a direction opposite to the apparent regional gradient. In Coral Springs analysis suggests a bifurcating plume migrating along two narrow zones. In Fort Pierce it was difficult to detect leachate because of mineralized irrigation water and fertilizer runoff from an adjacent citrus grove.     

RECIRCULATING WELLS: GROUND WATER REMEDIATION AND PROTECTION OF SURFACE WATER RESOURCES1

ABSTRACT: Several chlorinated solvent plumes threaten the sole‐source aquifer underlying the Massachusetts Military Reservation at the western end of Cape Cod. Sensitive surface water features including ponds, cranberry bogs, and coastal wetlands are hydraulically connected to the aquifer. For one of the plumes (CS‐10 the original remedy of 120 extraction and reinjection wells has the potential for significant disruption of surface water hydrology, through the localized drawdown and mounding of the water table. Recirculating wells with in‐well air stripping offer a cost‐effective alternative to conventional pump‐and‐treat technology that does not adversely affect the configuration of the water table. Pilot testing of a two well system, pumping 300 gpm, showed a capture radius of > 200 feet per well, in‐well trichloroethylene (TCE) removal efficiencies of 92 to 98 percent per recirculation cycle, an average of three recirculation cycles within the capture zone, and no measurable effect on water table elevations at any point within the recirculation/treatment zone. During 120 days of operation, the mean concentration of TCE in the treatment zone was reduced by 83 percent, from 1,111 μg/l to 184 μg/l. Full‐scale design projections indicate that 60 wells at an average spacing of 160 feet, having an aggregate recirculation 11 MGD, can contain the CS‐b plume without ground water extraction or adverse hydraulic effects on surface water resources. The estimated capital costs for such a system are about $7 million, and annual operations‐and‐maintenance costs should be about $1.4 million, 40 percent of those associated with a pump and treat system over a 20‐year period.     

OPTIMIZATION OF INTERMITTENT PUMPING SCHEDULES FOR AQUIFER REMEDIATION USING A GENETIC ALGORITHM1

ABSTRACT: Using a genetic algorithm (GA), optimal intermittent pumping schedules were established to simulate pump‐and‐treat remediation of a contaminated aquifer with known hydraulic limitations and a water miscible contaminant, located within the Duke Forest in Durham, North Carolina. The objectives of the optimization model were to minimize total costs, minimize health risks, and maximize the amount of contaminant removed from the aquifer. Stochastic ground water and contaminant transport models were required to provide estimates of contaminant concentrations at pumping wells. Optimization model simulations defined a tradeoff curve between the pumping cost and the amount of contaminant extracted from the aquifer. For this specific aquifer/miscible contaminant combination, the model simulations indicated that pump‐and‐treat remediation using intermittent pumping schedules for each pumping well produced significant reductions in predicted contaminant concentrations and associated health risks at a reasonable cost, after a remediation time of two years.     

Prediction of groundwater contamination with multivariate regression and probabilistic capture zones

Probabilistic capture zones are combined with a regression model and used as buffer zones around wells for Tobit regression analysis to predict contaminant concentration of groundwater in an agricultural region. A backward transport equation, which is a mathematical model based on the physical processes of solute transport, is used to delineate probabilistic capture zones. The probabilistic capture zone defines the area where contaminant discharge can have a direct influence, with pertinent probability, on the quality of groundwater pumped from a well. Tobit regression analysis is used to find the relationship between independent regression variables and a dependent variable, which is contaminant concentration in this study. The capture zone and the regression are combined into a model, and its applicability for prediction of nitrate concentration is tested in a small agricultural basin in Chuncheon, Korea, which is occupied mainly by vegetation fields, orchards, and small barns. Three cases of Model 1, Model 2, and Model 3 are compared in which buffer zones are circles, capture zones with probability over 0.1, and capture zones divided into sections with different probabilities, respectively. The resulting regression model describes nitrate concentration in terms of selected independent variables. When the concentrations are calculated with the model, the best fit with the observed concentrations was in Model 3. This result supports the applicability of the method proposed in this study to prediction of contaminant concentration of groundwater.     

A Method for Designing Detection Monitoring Networks in Layered Aquifers with Non-uniform Flow

An integer programming method was devised to locate detection monitoring wells in layered aquifers. The method is applicable to aquifers with non-uniform groundwater flow, and it does not require that a compliance boundary be linear or perpendicular to the direction(s) of groundwater flow. In each layer, monitoring sites are defined along curvilinear transects that parallel equipotential lines. The model can be formulated to allocate wells to the transect with the highest detection efficiency, or to establish multiple lines of defense against contaminant migrating to a compliance boundary. Detection efficiencies of alternative monitoring transects are calculated from parameters obtained via numerical modeling of contaminant transport. These parameters include the narrowest plume that could traverse a monitoring transect, and the zone width of potential contaminant migration at the transect. Problem formulations are compact, and computational requirements are low relative to alternative approaches for designing detection monitoring networks in aquifers. An application to a glacial outwash aquifer demonstrates the utility of the method.     

VELOCITY CONTROL AS A TOOL FOR OPTIMAL PLUME CONTAINMENT IN THE EQUUS BEDS AQUIFER,KANSAS1

ABSTRACT: A ground-water-management model was developed to investigate the best management options for the containment of an oil-field-brine plume in the Equus Beds aquifer in south-central Kansas. The main purpose of the management model was to find the optimal locations and minimum rates of pumpage of a set of plume-interception wells, to successfully reverse the velocity vectors at observation wells located along the plume front, and also to satisfy freshwater demands from supply wells. The effects of the calculated minimum withdrawals from the interception wells on the migration of contaminants throughout the ground-water system were evaluated utilizing a solute-transport model. This latter analysis was carried out to ensure the containment of the plume. Whereas application of the management model to the study area achieves the management objectives, the implementation of the results is believed to be impractical and expensive. This is because a considerable amount of water must be pumped out to reverse the velocity vectors in the vicinity of the plume. In general, the proposed technique of pollutant containment may be effective when applied to aquifers having low hydraulic gradients and/or to aquifers with hazardous plumes whose containment is not subject to economic constraints.     

MODELING CONCENTRATION VARIATIONS IN HIGH-CAPACITY WELLS: IMPLICATIONS FOR GROUNDWATER SAMPLING1

ABSTRACT: High-capacity wells are used as a convenient and economical means of sampling groundwater quality. Although the inherent limitations of using these wells are generally recognized, little has been done to investigate how these wells actually sample groundwater. A semi-analytical particle tracking model is used to illustrate the influence of variable vertical contaminant distributions and aquifer heterogeneity on the composition of water samples from these wells during short pumping periods. The hypothetical pumping well used in the simulations is located in an unconfined, alluvial aquifer with a shallow water table and concentration gradients of nitrate-nitrogen contamination. This is a typical setting for many irrigated areas in the United States. The main conclusions are: (1) high-capacity wells underestimate the average amount of contamination within an aquifer; (2) shapes of concentration-time curves for high-capacity wells appear to be governed by the distribution of the contaminant and travel times to the well; (3) variables such as well construction, pumping rate, and hydrogeologic properties contribute to the magnitude of the concentration-time curves at individual high-capacity wells; and (4) a sampling strategy using concentration-time curves based on the behavioral characteristics of the well rather than individual samples will provide a much better framework for interpreting spatial contaminant distributions.     

GROUND WATER HYDRAULICS CONSIDERATIONS REGARDING LANDFILLS1

ABSTRACT: Landfill siting and design guidelines or regulations differ from state to state. Most include hydrogeological criteria, referring to hydraulic conductivities, aquifers, ground water flow patterns, contaminant travel times, and distance between landfill and sensitive targets for contaminants, etc. However, almost all of the existing hydrogeological guidelines are incomplete, inconsistent, or both. The aquitard between landfill and regional aquifer frequently offers less resistance to leachate migration than compliance with regulations may suggest. Residence times of leachate, that makes it through the landfill liner, is often overestimated. Monitoring wells in the regional aquifer are unreliable detectors of local leaks in a landfill. If a landfill does leak, costly aquifer restoration is called for. For traditional landfill designs, ground water monitoring considerations suggest the siting over homogeneous sand and gravel aquifers, rather than over complex till environments. An alternative landfill design criterion is suggested, which is based on a negative hydraulic gradient underneath the landfill. This design guarantees ground water protection, simplifies landfill monitoring, and generally enhances the landfill economy.     

CONTROL OF NATURAL BRINE SPRINGS IN BRAZOS RIVER BASIN PART II: BRINE DISPOSAL1

ABSTRACT: Water quality in the Brazos River of Texas is seriously degraded by natural salt pollution. Two thousand tons/day of total dissolved solids emanate from brine springs and seeps in the Upper Brazos River drainage. Approximately 45 percent of the total salt load comes from a relatively small flow in the Dove Creek area. The companion paper demonstrates that a system of wells pumping brine at a constant rate of about 2 cfs from the near surface aquifer should eliminate the brine springs in this area. In this paper, injection into deep brine aquifers is shown to be a feasible brine disposal alternative. Four brine aquifers were determined from the literature to be possible injection zones. Accurate net aquifer thickness maps were generated in a 23 by 14 mile area centered on the Dove Creek area for three of the aquifers from an interpretation of 41 well logs. Constant injection for a project life of 100 years was simulated using the SWIFT/486 software. Modeling suggests that one well would be sufficient to inject the entire disposal volume into either the Strawn or Ellenburger Formation.     

AN EMPIRICALLY‐BASED SEQUENTIAL GROUND WATER MONITORING NETWORK DESIGN PROCEDURE1

ABSTRACT: A procedure using a simple, empirically‐based model that makes efficient use of available information has been developed for designing a ground water monitoring well network. A moving plume is described by siting wells in a sequential manner, relying upon two‐dimensional concentration data obtained from previously installed wells to determine the locations of future wells. Data sets from two well known, densely monitored natural gradient tracer studies were used to test the procedure. Plumes defined by all information in the original networks were compared to those defined by reduced networks designed by the new procedure. The new procedure tracked the plumes using only a portion of that information. The new procedure could have reduced the number of wells in the original tests by about 50 percent without appreciable loss of plume information as measured by plume location and extent and by tracer mass.     

Discharge of oilfield-produced water in nueces bay,texas: A case study

During oil and gas production, water is often extracted from geological formations along with the hydrocarbons. These "produced waters" have been discharged to Nueces Bay since the turn of the century. These effluents were found to be highly toxic, and sediments in the vicinity of the discharges were also toxic. We developed a map of wells and produced-water discharge sites in the vicinity of Nueces Bay and identified numerous unplugged wells suitable for conversion to produced water disposal wells. An economic analysis of conversion to subterranean injection of produced water indicates that most of the wells currently in production could pay out the cost of conversion to injection in one to three years. The use of one injection well for two or more water-producing wells could yield greater savings. Wells that could not support the cost of injection are small producers, and their loss would not constitute a major loss of jobs or dollars to the area. This study could serve as a useful model for evaluating the economic feasibility of conversion to injection in other areas of Texas and Louisiana.     

Land management impacts on dairy-derived dissolved organic carbon in ground water

Dairy operations have the potential to elevate dissolved organic carbon (DOC) levels in ground water, where it may interact with organic and inorganic contaminants, fuel denitrification, and may present problems for drinking water treatment. Total and percent bioavailable DOC and total and carbon-specific trihalomethane (THM) formation potential (TTHMFP and STHMFP, respectively) were determined for shallow ground water samples from beneath a dairy farm in the San Joaquin Valley, California. Sixteen wells influenced by specific land management areas were sampled over 3 yr. Measured DOC concentrations were significantly elevated over the background as measured at an upgradient monitoring well, ranging from 13 to 55 mg L(-1) in wells downgradient from wastewater ponds, 8 to 30 mg L(-1) in corral wells, 5 to 12 mg L(-1) in tile drains, and 4 to 15 mg L(-1) in wells associated with manured fields. These DOC concentrations were at the upper range or greatly exceeded concentrations in most surface water bodies used as drinking water sources in California. DOC concentrations in individual wells varied by up to a factor of two over the duration of this study, indicating a dynamic system of sources and degradation. DOC bioavailability over 21 d ranged from 3 to 10%, comparable to surface water systems and demonstrating the potential for dairy-derived DOC to influence dissolved oxygen concentrations (nearly all wells were hypoxic to anoxic) and denitrification. TTHMFP measurements across all management units ranged from 141 to 1731 microg L(-1), well in excess of the maximum contaminant level of 80 microg L(-1) established by the Environmental Protection Agency. STHMFP measurements demonstrated over twofold variation ( approximately 4 to approximately 8 mmol total THM/mol DOC) across the management areas, indicating the dependence of reactivity on DOC composition. The results indicate that land management strongly controls the quantity and quality of DOC to reach shallow ground water and hence should be considered when managing ground water resources and in any efforts to mitigate contamination of ground water with carbon-based contaminants, such as pesticides and pharmaceuticals.     

井场含油固体废物综合治理及应用研究

在井下作业中,原油、废水与地表土壤及铺垫井场地面的废钢渣等相混合,形成了特殊的作业井场含油固体废物。为此,采用了两种处理方法对该类含油固体废物进行综合治理研究。一是向受油污染的土壤中直接投放营养物,促进土壤里的细菌和微生物繁殖;二是将受油污染的土壤集中堆积在处理场进行统一处理。试验结果表明:第一种处理工艺要求较高,目前还难以推广应用。选用含油固体废物替代部分粉煤灰来烧制红砖,这种处理方法符合国家倡导的发展绿色环保型建筑材料的方向,为建材行业提供了优质的助燃材料。该技术比其他处理技术成本低,因此具有推广和应用价值。     

STREAM DEPLETION BY WELLS IN THE SOUTH PLATTE BASIN-COLORADO1

The agricultural production from the Lower South Platte Basin in Colorado represents a significant portion of the state economy. Until the early 1950's the production had developed almost exclusively by use of river water. Drought conditions combined with improved well technology resulted in an inordinate amount of well development in the valley during the period 1952-56. These wells were used for supplemental supply in many cases, but the application of sprinkler irrigation brought many acres of here-to-fore dry land into irrigated production. As a result of the vast amounts of groundwater withdrawal by the newly developed wells, senior surface appropriators found a decreasing amount of water available for use in the streams. The legislature, observing the doctrine of prior appropriation, ruled that all surface and ground water in a tributary would be treated and administered as one resource. This, of course, spelled doom for the well-oriented segment of the economy. Analysis of a segment of the river on an inflow-outflow basis was made with careful determination of all inflow-outflow in the study reach to include correlations required to determine ungaged side-channel in-flow and unmetered irrigation wells. Results indicate that wells have intercepted normal return flows to the river resulting in a decreased amount of surface water during the irrigation season. Stream depletion appears to equal the expected consumptive use of well water which ranged between 40% to 50% of the groundwater extraction.     

OPTIMAL MANAGEMENT OF RELIEF WELLS NEAR WATERTON RESERVOIR1

ABSTRACT: This study considers the design and analysis of nonpumped well systems to provide pressure relief in the Cochrane aquifer, which is hydraulically connected to the Waterton Reservoir, Analyses of the relief well management problem are performed with a management model formulated by the combined simulation-optimization approach. The model determines active relief well sites and their optimal discharge schedules. The existing relief wells are inadequate to provide the desirable pressure relief. The locations and design capacities of two new relief well systems are determined by the management model. The relationships between reservoir level and well discharge are estimated for these two well systems.     

EXPANSION OF SALT-WATER ZONE DUE TO WELL DISCHARGE1

ABSTRACT: In coastal confined aquifers, the extent of the salt-water wedge due to natural ground-water flow can be determined by available methods. If water is pumped by a discharge well, the quality of the water depends upon the rate and duration of pumping as well as the location of the well. A study has been made to find the extent of the progress of salt-water intrusion due to the operation of one discharge well taking into account various conditions of aquifer properties, pump capacities, natural flows, time effects, and well locations. Dimension-less solutions for specific conditions have been obtained by means of a simple computer program. Range of most common conditions is discussed. One of the main findings of this study was that salt water may be pumped out of a well even if it is located in an initially totally fresh-water zone beyond the natural salt/fresh-water interface.     

Quality of Water from Hand Dug Wells in Onitsha Metropolitan Areas of Nigeria

Summary Wide Range of human and anthropogenic activities impinges on the urban environment in most cities in Nigeria, to degrade the quality of water resources. Some of these activities (daily discharge of solid and liquid waste, industrial effluent, and physo-chemical weathering processes) are discharged directly on sources of water supply to the populace of Onitsha. Based on this problem, this paper examines the quality of water from hand-dug wells in Onitsha. 15 wells water samples were collected during the month of January, July, and August with the aid of sterilized containers. And sent to the laboratory for analyses, results showed that wells that are located close to dumpsites are more polluted in terms of turbidity, TSS, CaCo₂ conductivity salinity acidity, Pb, Fe and bacteriological quality of the well water. Also most of the hand-dug well water qualities are unsafe for human consumption, because they are generally above the WHO maximum acceptable threshold. Since this source of water form one of the major source of water to the inhabitants, there is need for purification proper disposal of waste, public education of the health implication of waste/impure water and other management measures.     

Modeling the Potential Impact of Seasonal and Inactive Multi‐Aquifer Wells on Contaminant Movement to Public Water‐Supply Wells1

Johnson, R.L., B.R. Clark, M.K. Landon, L.J. Kauffman, and S.M. Eberts, 2011. Modeling the Potential Impact of Seasonal and Inactive Multi‐Aquifer Wells on Contaminant Movement to Public Water‐Supply Wells. Journal of the American Water Resources Association (JAWRA) 47(3):588‐596. DOI: 10.1111/j.1752‐1688.2011.00526.x Abstract: Wells screened across multiple aquifers can provide pathways for the movement of surprisingly large volumes of groundwater to confined aquifers used for public water supply (PWS). Using a simple numerical model, we examine the impact of several pumping scenarios on leakage from an unconfined aquifer to a confined aquifer and conclude that a single inactive multi‐aquifer well can contribute nearly 10% of total PWS well flow over a wide range of pumping rates. This leakage can occur even when the multi‐aquifer well is more than a kilometer from the PWS well. The contribution from multi‐aquifer wells may be greater under conditions where seasonal pumping (e.g., irrigation) creates large, widespread downward hydraulic gradients between aquifers. Under those conditions, water can continue to leak down a multi‐aquifer well from an unconfined aquifer to a confined aquifer even when those multi‐aquifer wells are actively pumped. An important implication is that, if an unconfined aquifer is contaminated, multi‐aquifer wells can increase the vulnerability of a confined‐aquifer PWS well.     

CASING AND LEAK DEPTHS,AND SOLUTE TRAVEL TIMES TO WELLS1

ABSTRACT: A mathematical solution based on porous media flow is developed for solute travel time to a well as affected by a leak around the upper part of the casing. Consider a well of radius 0.2 meters (m) penetrating, fully, a semiconfined aquifer of thickness 6 m with impermeable casing length of 4.5 m, and screened casing length 1.5 m. Around the upper 1.5 m of the impermeable casing length, there is a highly permeable region (a leak). The radius of influence of the well is 10 m. The porous flow medium has a hydraulic conductivity of 10 m/day and a porosity of 0.25. Between the water table and the water level in the well, there is a steady state pumped down head difference of 0.3 m. Solute travel time from a point at the bottom of the leak to the well is 2.33 days. If the leak is sealed (grouted), the travel time is 6.24 days. Examples of six different geometries are given. Laboratory studies verify the theory. The computations should be useful in the design and protection of water wells from solutes, such as from agriculture, industry, strip mines, or sanitary landfills.     

Removal of radium from groundwater using a modified bauxite refinery residue

Radium (Ra) removal by an unconventional sorbent, a modified bauxite refinery residue (MBRR), is investigated for a groundwater extracted in Missouri, USA. The MBRR treatment causes substantial reductions of both gross α and combined Ra activities from 0.955 ± 0.005 and 0.66 ± 0.005 Bq L to below detection limits (0.037 Bq L or 1 pCi L). Column breakthrough occurs at 0.555 Bq L for gross α and 0.185 Bq L for combined Ra (15 and 5 pCi L; USEPA's maximum contaminant levels) after 54 and 40 d run time, respectively. At 84 d the MBRR media continues to remove 24.3% of raw water gross α and 39.7% of the combined Ra. The treatment effluent has an initial pH of 10.9, outside the USEPA guides (6.5-8.5); this may be readily mitigated by posttreatment acid injection, or by raw water blending. The MBRR simultaneously removes other potentially hazardous trace elements (e.g., Cu, Zn, and Fe) to extremely low concentrations. In addition, toxicity characteristic leaching procedure testing of spent MBRR suggests that metals are bound tightly, such that it is nonhazardous, permitting cost-effective disposal to landfill without special confinement or storage. Consequently, MBRR may be utilized as an alternative adsorbent for treating Ra-contaminated groundwater.