Experimental measurement and modeling of the rate of absorption of carbon dioxide by aqueous ammonia

In this work, the rate of absorption of carbon dioxide by aqueous ammonia solvent has been studied by applying a newly built wetted wall column. The absorption rate in aqueous ammonia was measured at temperatures from 279 to 304 K for 1 to 10 wt% aqueous ammonia with loadings varying from 0 to 0.8 mol CO₂/mol NH₃. The absorption rate in 30 wt% aqueous mono-ethanolamine (MEA) was measured at 294 and 314 K with loadings varying from 0 to 0.4 as comparison.It was found that at 304 K, the rate of absorption of carbon dioxide by 10 wt% NH₃ solvent was comparable to the rates for 30 wt% MEA at 294 and 314 K (a typical absorption temperature for this process). The absorption rate using ammonia was however significantly lower at temperatures of 294 K and lower as applied in the Chilled Ammonia Process. However, at these low temperatures, the rate of absorption in ammonia has only a small temperature dependency.The rate of absorption decreases strongly with decreasing ammonia concentrations and increasing CO₂ loadings.The rate of absorption of carbon dioxide by aqueous ammonia solvent was modeled using the measurements of the unloaded solutions and the zwitter-ion mechanism. The model could successfully predict the experimental measurements of the absorption rate of CO₂ in loaded ammonia solutions.     

CO2 capture from hot stove gas in steel making process

The capture of CO₂ from a hot stove gas in steel making process containing 30 vol% CO₂ by chemical absorption in a rotating packed bed (RPB) was studied. The RPB had an inner diameter of 7.6 cm, an outer diameter of 16 cm, and a height of 2 cm. The aqueous solutions containing 30 wt% of single and mixed monoethanolamine (MEA), 2-(2-aminoethylamino)ethanol (AEEA), and piperazine (PZ) were used. The CO₂ capture efficiency was found to increase with increasing temperature in a range of 303–333 K. It was also found to be more dependent on gas and liquid flow rates but less dependent on rotating speed when the speed was higher than 700 rpm. The obtained results indicated that the mixed alkanolamine solutions containing PZ were more effective than the single alkanolamine solutions. This was attributed to the highest reaction rate of PZ with CO₂. A higher portion of PZ in the mixture was more favorable to CO₂ capture. The highest gas flow rates allowed to achieve a desired CO₂ capture efficiency and the correspondent height of transfer unit (HTU) were determined at different aqueous solution flow rates. Because all the 30 wt% single and mixed alkanolamine solutions could result in a HTU less than 5.0 cm at a liquid flow rate of 100 mL/min, chemical absorption in a RPB instead of a packed bed adsorber is therefore suggested to capture CO₂ from the flue gases in steel making processes.     

Techno-Economic Study of CO2 Capture from an Existing Cement Plant Using MEA Scrubbing

Carbon dioxide is the major greenhouse gas responsible for global warming. Man-made CO₂ emissions contribute approximately 63% of greenhouse gases and the cement industry is responsible for approximately 5% of CO₂ emissions emitting nearly 900 kg of CO₂ per 1000 kg of cement. CO₂ from a cement plant was captured and purified to 98% using the monoethanolamine (MEA) based absorption process. The capture cost was $51 per tonne of CO₂ captured, representing approximately 90% of total cost. Steam was the main operating cost representing 39% of the total capture cost. Switching from coal to natural gas reduces CO₂ emissions by about 18%. At normal load, about 36 MW of waste heat is available for recovery to satisfy the parasitic heat requirements of MEA process; however, it is very difficult to recover.     

Integration of CO2 capture unit using single- and blended-amines into supercritical coal-fired power plants: Implications for emission and energy management

This work provides the essential information and approaches for integration of carbon dioxide (CO₂) capture units into power plants, particularly the supercritical type, so that energy utilization and CO₂ emissions can be well managed in the subject power plants. An in-house model, developed at the University of Regina, Canada, was successfully used for simulating a 500 MW supercritical coal-fired power plant with a post-combustion CO₂ capture unit. The simulations enabled sensitivity and parametric study of the net efficiency of the power plant, the coal consumption rate, and the amounts of CO₂ captured and avoided. The parameters of interest include CO₂ capture efficiency, type of coal, flue gas delivery scheme, type of amine used in the capture unit, and steam pressure supplied to the capture unit for solvent regeneration. The results show that the advancement of MEA-based CO₂ capture units through uses of blended monoethanolamine–methyldiethanolamine (MEA–MDEA) and split flow configuration can potentially make the integration of power plant and CO₂ capture unit less energy intensive. Despite the increase in energy penalty, it may be worth capturing CO₂ at a higher efficiency to achieve greater CO₂ emissions avoided. The flue gas delivery scheme and the steam pressure drawn from the power plant to the CO₂ capture unit should be considered for process integration.     

CO2 capture from power plants: Part I. A parametric study of the technical performance based on monoethanolamine

Capture and storage of CO₂ from fossil fuel fired power plants is drawing increasing interest as a potential method for the control of greenhouse gas emissions. An optimization and technical parameter study for a CO₂ capture process from flue gas of a 600 MWe bituminous coal fired power plant, based on absorption/desorption process with MEA solutions, using ASPEN Plus with the RADFRAC subroutine, was performed. This optimization aimed to reduce the energy requirement for solvent regeneration, by investigating the effects of CO₂ removal percentage, MEA concentration, lean solvent loading, stripper operating pressure and lean solvent temperature.Major energy savings can be realized by optimizing the lean solvent loading, the amine solvent concentration as well as the stripper operating pressure. A minimum thermal energy requirement was found at a lean MEA loading of 0.3, using a 40 wt.% MEA solution and a stripper operating pressure of 210 kPa, resulting in a thermal energy requirement of 3.0 GJ/ton CO₂, which is 23% lower than the base case of 3.9 GJ/ton CO₂. Although the solvent process conditions might not be realisable for MEA due to constraints imposed by corrosion and solvent degradation, the results show that a parametric study will point towards possibilities for process optimisation.     

CO2 capture from power plants: Part II. A parametric study of the economical performance based on mono-ethanolamine

While the demand for reduction in CO₂ emission is increasing, the cost of the CO₂ capture processes remains a limiting factor for large-scale application. Reducing the cost of the capture system by improving the process and the solvent used must have a priority in order to apply this technology in the future. In this paper, a definition of the economic baseline for post-combustion CO₂ capture from 600 MW_e bituminous coal-fired power plant is described. The baseline capture process is based on 30% (by weight) aqueous solution of monoethanolamine (MEA). A process model has been developed previously using the Aspen Plus simulation programme where the baseline CO₂-removal has been chosen to be 90%. The results from the process modelling have provided the required input data to the economic modelling. Depending on the baseline technical and economical results, an economical parameter study for a CO₂ capture process based on absorption/desorption with MEA solutions was performed.Major capture cost reductions can be realized by optimizing the lean solvent loading, the amine solvent concentration, as well as the stripper operating pressure. A minimum CO₂ avoided cost of € 33 tonne⁻¹ CO₂ was found for a lean solvent loading of 0.3 mol CO₂/mol MEA, using a 40 wt.% MEA solution and a stripper operating pressure of 210 kPa. At these conditions 3.0 GJ/tonne CO₂ of thermal energy was used for the solvent regeneration. This translates to a € 22 MWh⁻¹ increase in the cost of electricity, compared to € 31.4 MWh⁻¹ for the power plant without capture.     

A statistical analysis of the carbon dioxide capture process

Post combustion carbon dioxide (CO₂) capture is one of the most commonly adopted technologies for reducing industrial CO₂ emissions, which is now an important goal given the widespread concern over global warming. Research on amine-based CO₂ capture has mainly focused on improving effectiveness and efficiency of the CO₂ capture process. Our research work focuses on studying the relationships among the significant parameters influencing CO₂ production because an enhanced understanding of the intricate relationships among the parameters involved in the process is critical for improving efficiency of the CO₂ capture process. This paper presents a statistical study that explores the relationships among parameters involved in the amine-based post combustion CO₂ capture process at the International Centre for CO₂ Capture (ITC) located in Regina, Saskatchewan of Canada. A multiple regression technique has been applied for analysis of data collected at the CO₂ capture pilot plant at ITC. The parameters have been carefully selected to avoid issues of multicollinearity, and four mathematical models among the key parameters identified have been developed. The models have been tested, and accuracy of the models is found to be satisfactory. The models developed in this study describe part of the CO₂ capture process and can help to predict performance of the CO₂ capture process at ITC under different conditions. Some results from a preliminary validation process will also be presented.     

Numerical parametric study on CO2 capture by indirect thermal swing adsorption

Post-combustion CO₂ capture remains one of the most-challenging issue to lower CO₂ emissions of existing power plants or heavy industry installations because of strong economy and energy efficiency aspects. The major issue comes from CO₂ dilution (4% for NGCC and 14% for PC) and the high flow rates to be treated. Furthermore, CO₂ purity has to be higher than 95% with recovery at 90%, to match the transportation/injection requirements.The MEA absorption process remains the reference today but its energy consumption (about 3 MJ/kg_CO2) and the amine consumption are still challenging drawbacks.The interest of CO₂ capture by indirect TSA (Temperature Swing Adsorption) was demonstrated experimentally in a previous work. The aim of this paper is to present the results of a numerical parametric study. Two main parameters are explored: the desorption temperature (100–200 °C) and the purge flow rate (0.1–0.5 Ndm³ min⁻¹). Four performance indicators are evaluated: CO₂ purity, recovery, productivity and specific energy consumption.Results show that purity above 95% can be achieved. Keeping the 95% target, it is possible to achieve recovery at 81% with productivity at 57.7 g_CO2/kg_ads h and a specific energy consumption of 3.23 MJ/kg_CO2, which is less than for the reference MEA process.Comparison with other adsorption processes exhibits that this process has good potential especially since some improvements are still expected from further research.     

Dynamis CO2 quality recommendations

In the carbon capture and storage (CCS) chain, transport and storage set different requirements for the composition of the gas stream mainly containing carbon dioxide (CO₂). Currently, there is a lack of standards to define the required quality for CO₂ pipelines. This study investigates and recommends likely maximum allowable concentrations of impurities in the CO₂ for safe transportation in pipelines. The focus is on CO₂ streams from pre-combustion processes. Among the issues addressed are safety and toxicity limits, compression work, hydrate formation, corrosion and free water formation, including the cross-effect of H₂S and H₂O and of H₂O and CH₄.     

Techno-economic study of CO2 capture from natural gas based hydrogen plants

Canadian oil sands are considered to be the second largest oil reserves in the world. However, the upgrading of bitumen from oil sands to synthetic crude oil (SCO) requires nearly ten times more hydrogen (H₂) than conventional crude oils. The current H₂ demand for oil sands operations is met mostly by steam reforming of natural gas (SMR). The future expansion of oil sands operations is likely to quadruple the demand of H₂ for oil sand operations in the next decade.This paper presents modified process schemes that capture CO₂ at minimum energy penalty in modern SMR plants. The approach is to simulate a base case H₂ plant without CO₂ capture and then look for the best operating conditions that minimize the energy penalty associated with CO₂ capture while maximizing H₂ production. The two CO₂ capture schemes evaluated in this study include a membrane separation process and the monoethanolamine (MEA) absorption process. A low energy penalty is observed when there is lower CO₂ production and higher steam production. The process simulation results show that the H₂ plant with CO₂ capture has to be operated at lower steam to carbon ratio (S/C), higher inlet temperature of the SMR and lower inlet temperatures for the water gas-shift (WGS) converters to attain lowest energy penalty. Also it is observed that both CO₂ capture processes, the membrane process and the MEA absorption process, are comparable in terms of energy penalty and CO₂ avoided when both are operated at conditions where lowest energy penalty exists.     

Life cycle assessment of natural gas combined cycle power plant with post-combustion carbon capture,transport and storage

Hybrid life cycle assessment has been used to assess the environmental impacts of natural gas combined cycle (NGCC) electricity generation with carbon dioxide capture and storage (CCS). The CCS chain modeled in this study consists of carbon dioxide (CO₂) capture from flue gas using monoethanolamine (MEA), pipeline transport and storage in a saline aquifer.Results show that the sequestration of 90% CO₂ from the flue gas results in avoiding 70% of CO₂ emissions to the atmosphere per kWh and reduces global warming potential (GWP) by 64%. Calculation of other environmental impacts shows the trade-offs: an increase of 43% in acidification, 35% in eutrophication, and 120–170% in various toxicity impacts. Given the assumptions employed in this analysis, emissions of MEA and formaldehyde during capture process and generation of reclaimer wastes contributes to various toxicity potentials and cause many-fold increase in the on-site direct freshwater ecotoxicity and terrestrial ecotoxicity impacts. NO_x from fuel combustion is still the dominant contributor to most direct impacts, other than toxicity potentials and GWP. It is found that the direct emission of MEA contribute little to human toxicity (HT < 1%), however it makes 16% of terrestrial ecotoxicity impact. Hazardous reclaimer waste causes significant freshwater and marine ecotoxicity impacts. Most increases in impact are due to increased fuel requirements or increased investments and operating inputs.The reductions in GWP range from 58% to 68% for the worst-case to best-case CCS system. Acidification, eutrophication and toxicity potentials show an even large range of variation in the sensitivity analysis. Decreases in energy use and solvent degradation will significantly reduce the impact in all categories.     

Worst case scenario study to assess the environmental impact of amine emissions from a CO2 capture plant

Use of amines is one of the leading technologies for post-combustion carbon dioxide capture from gas and coal-fired power plants. This study assesses the potential environmental impact of emissions to air that result from use of monoethanol amine (MEA) as an absorption solvent for the capture of carbon dioxide (CO₂). Depending on operation conditions and installed reduction technology, emissions of MEA to the air due to solvent volatility losses are expected to be in the range of 0.01–0.8 kg/tonne CO₂ captured. Literature data for human and environmental toxicity, together with atmospheric dispersion model calculations, were used to derive maximum tolerable emissions of amines from CO₂ capture. To reflect operating conditions with typical and with elevated emissions, we defined a scenario MEA-LOW, with emissions of 40 t/year MEA and 5 t/year diethyl amine (DEYA), and a scenario MEA-HIGH, with emissions of 80 t/year MEA and 15 t/year DEYA. Maximum MEA deposition fluxes would exceed toxicity limits for aquatic organisms by about a factor of 3–7 depending on the scenario. Due to the formation of nitrosamines and nitramines, the estimated emissions of DEYA are close to or exceed safety limits for drinking water and aquatic ecosystems. The “worst case” scenario approach to determine maximum tolerable emissions of MEA and other amines is in particular useful when both expected environmental loads and the toxic effects are associated with high uncertainties.     

Post-combustion CO2-capture from coal-fired power plants: Preliminary evaluation of an integrated chemical absorption process with piperazine-promoted potassium carbonate

The simulation tool ASPEN Plus^® is used to model the full CO₂-capture process for chemical absorption of CO₂ by piperazine-promoted potassium carbonate (K₂CO₃/PZ) and the subsequent CO₂-compression train. Sensitivity analysis of lean loading, desorber pressure and CO₂-capture rate are performed for various solvent compositions to evaluate the optimal process parameters. EbsilonProfessional^® is used to model a 600 MW_el (gross) hard coal-fired power plant. Numerical equations for power losses due to steam extraction for solvent regeneration are derived from simulation runs. The results of the simulation campaigns are used to find the process parameters that show the lowest specific power loss. Subsequently, absorber and desorber columns are dimensioned to evaluate investment costs for these main components of the CO₂-capture process. Regeneration heat duty, net efficiency losses and column investment costs are then compared to the reference case of CO₂-capture by monoethanolamine (MEA).CO₂-capture by piperazine-promoted potassium carbonate with subsequent CO₂-compression to 110 bar shows energetic advantages over the reference process which uses MEA. Additionally, investment costs for the main components in the CO₂-capture process (absorber and desorber columns) are lower due to the enhanced reaction kinetics of the investigated K₂CO₃/PZ solvent which leads to smaller component sizes.     

Mercury measurement and control in a CO2-enriched flue gas

Oxycombustion is being considered as a promising solution to carbon capture and sequestration. Standard sampling and measurement methods may or may not be valid under oxycombustion conditions because the flue gas differs significantly from that of conventional air-blown coal combustion.Bench-scale tests were conducted to evaluate the measurement validity of continuous mercury monitors (CMMs), with and without a flue gas preconditioning unit, in a simulated oxycombustion flue gas with varied CO₂ concentrations. Tests also included mercury capture with activated carbon in typical oxyfuel combustion flue gas. Research data indicated that highly concentrated CO₂ streams affect the accuracy of the mass flow rate and the subsequent gaseous mercury measurement, although this is specific to the type of CMM. Concentrated CO₂ streams also induced solid precipitation in the wet-chemistry conversion unit and resulted in a biased measurement of the gas-phase mercury. Flue gas dilution appeared to provide accurate measurement of total gas-phase mercury and be applicable to mercury measurement in highly concentrated CO₂ streams, although mercury speciation appeared to be problematic and will require additional modification and validation. Mercury capture with activated carbon under CO₂-enriched conditions showed similar performance to typical high-acid coal combustion flue gas.     

Kinetics of sulfur dioxide- and oxygen-induced degradation of aqueous monoethanolamine solution during CO2 absorption from power plant flue gas streams

Studies of the kinetics of sulfur dioxide (SO₂)- and oxygen (O₂)-induced degradation of aqueous monoethanolamine (MEA) during the absorption of carbon dioxide (CO₂) from flue gases derived from coal- or natural gas-fired power plants were conducted as a function of temperature and the liquid phase concentrations of MEA, O₂, SO₂ and CO₂. The kinetic data were based on the initial rate which shows the propensity for amine degradation and obtained under a range of conditions typical of the CO₂ absorption process (3–7 kmol/m³ MEA, 6% O₂, 0–196 ppm SO₂, 0–0.55 CO₂ loading, and 328–393 K temperature). The results showed that an increase in temperature and the concentrations of MEA, O₂ and SO₂ resulted in a higher MEA degradation rate. An increase in CO₂ concentration gave the opposite effect. A semi-empirical model based on the initial rate, ?r_MEA = {6.74 × 10⁹ e^?(29,403/RT)[MEA]^0.02([O]^2.91 + [SO₂]^3.52)}/{1 + 1.18[CO₂]^0.18} was developed to fit the experimental data. With the higher order of reaction, SO₂ has a higher propensity to cause MEA to degrade than O₂. Unlike previous models, this model shows an improvement in that any of the parameters (i.e. O₂, SO₂, and CO₂) can be removed without affecting the usability of the model.     

Ionic liquids for post-combustion CO2 absorption

The present work is a study to evaluate ionic liquids as a potential solvent for post-combustion CO₂ capture. In order to enhance the absorption performance of a CO₂ capture unit, different ionic liquids have been designed and tested. The main goal was to get a comparison between a reference liquid and selected ionic liquids. As the reference, a solution of 30 w% monoethanolamine (MEA) and water was used. A large range of different pure and diluted ionic liquids was tested with a special screening process to gain general information about the CO₂ absorption performance. Based on these results, a 60 w% ionic liquid solution in water was selected and the vapour–liquid equilibrium was measured experimentally between 40 °C and 110 °C. From these curves the enthalpy of absorption for capturing CO₂ into the ionic liquid was determined. With these important parameters one is able to calculate the total energy demand for stripping of CO₂ from the loaded solvent for comparison of the ionic liquid based solvent with the reference MEA solvent. The energy demand of this 60 w% ionic liquid is slightly lower than that of the reference solution, resulting in possible energy savings between 12 and 16%.     

Carbon dioxide capture with concentrated,aqueous piperazine

Concentrated, aqueous piperazine (PZ) has been investigated as a novel amine solvent for carbon dioxide (CO₂) absorption. The CO₂ absorption rate of aqueous PZ is more than double that of 7 m MEA and the amine volatility at 40 °C ranges from 11 to 21 ppm. Thermal degradation is negligible in concentrated, aqueous PZ up to a temperature of 150 °C, a significant advantage over MEA systems. Oxidation of concentrated, aqueous PZ is appreciable in the presence of copper (4 mM), but negligible in the presence of chromium (0.6 mM), nickel (0.25 mM), iron (0.25 mM), and vanadium (0.1 mM). Initial system modeling suggests that 8 m PZ will use 10–20% less energy than 7 m MEA. The fast mass transfer and low degradation rates suggest that concentrated, aqueous PZ has the potential to be a preferred solvent for CO₂ capture.     

CO2 transportation for carbon capture and storage: Sublimation of carbon dioxide from a dry ice bank

Climate change is being caused by greenhouse gases such as carbon dioxide (CO₂). Carbon capture and storage (CCS) is of interest to the scientific community as one way of achieving significant global reductions of atmospheric CO₂ emissions in the medium term. CO₂ would be captured from large stationary sources such as power plants and transported via pipelines under high pressure conditions to underground storage. If a downward leakage from a surface transportation system module occurs, the CO₂ would undergo a large temperature reduction and form a bank of “dry ice” on the ground surface; the sublimation of the gas from this bank represents an area source term for subsequent atmospheric dispersion, with an emission rate dependent on the energy balance at the bank surface. Gaseous CO₂ is denser than air and tends to remain close to the surface; it is an asphyxiant, a cerebral vasodilator and at high concentrations causes rapid circulatory insufficiency leading to coma and death. Hence a subliming bank of dry ice represents safety hazard. A model is presented for evaluating the energy balance and sublimation rate at the surface of a solid frozen CO₂ bank under different environmental conditions. The results suggest that subliming gas behaves as a proper dense gas (i.e. it remains close to the ground surface) only for low ambient wind speeds.     

Hollow fiber membrane separation process in the presence of gaseous and particle impurities for post-combustion CO2 capture

The membrane separation process for CO₂ capture can be interfered by the gaseous components and the fine particles in flue gas, especially in desulfurized flue gas. In this work, the pint-sized Polyimide(PI) hollow fiber membrane contactors were self-packed to investigate the membrane CO₂ separation from flue gas containing fine particles and gaseous contaminants (SO₂,SO₃,H₂O). First, the effects of SO₂, SO₃, water vapor, and gypsum particles on the CO₂ capture were studied independently and synergistically. The results showed that the effect of SO₂ on the membrane separation properties is indistinctive; however, the membrane performance was damaged seriously with the addition of SO₃. The high humidity promoted the CO₂ separation initially before inhibiting the PI membrane performance. Moreover, the decrease of the CO₂/N₂ selectivity and the permeation rate were accelerated with the coexistence of SO₂. The membrane performance showed an obvious deterioration in the presence of gypsum particles, with a 21% decrease in the CO₂/N₂ selectivity and 51% decrease in the permeation rate. Furthermore, the gypsum particles exerted dramatic damage. Under the WFGD conditions, the combined effects of SO₂, water vapor, and the gypsum particles influenced the stability of the membrane significantly. This tendency is mainly attributed to the deposition of fine particles and aerosol on the membrane surface, which occupied the effective area and enhanced the mass transfer resistance. This study of impurities’ influence could play an important role in further industrial application of membrane CO₂ capture.     

Parametric investigation of the calcium looping process for CO2 capture in a 10 kWth dual fluidized bed

Calcium looping (CaL) is a promising post-combustion CO₂ capture technology which is carried out in a dual fluidized bed (DFB) system with continuous looping of CaO, the CO₂ carrier, between two beds. The system consists of a carbonator, where flue gas CO₂ is adsorbed by CaO and a regenerator, where captured CO₂ is released. The CO₂-rich regenerator flue gas can be sequestered after gas processing and compression. A parametric study was conducted on the 10 kW_th DFB facility at the University of Stuttgart, which consists of a bubbling fluidized bed carbonator and a riser regenerator. The effect of the following parameters on CO₂ capture efficiency was investigated: carbonator space time, carbonator temperature and calcium looping ratio. The active space time in the carbonator, which is a function of the space time and the calcium looping ratio, was found to strongly correlate with the CO₂ capture efficiency. BET and BJH techniques provided surface area and pore volume distribution data, respectively, for collected sorbent samples. The rate of sorbent attrition was found to be 2 wt.%/h which is below the expected sorbent make-up rate required to maintain sufficient sorbent activity. Steady-state CO₂ capture efficiencies greater than 90% were achieved for different combinations of operational parameters. Moreover, the experimental results obtained were briefly compared with results derived from reactor modeling studies. Finally, the implications of the experimental results with respect to commercialization of the CaL process have been assessed.