A geostatistical and probabilistic spectral image processing methodology for monitoring potential CO2 leakages on the surface

Remote sensing has demonstrated success in various environmental applications over the past three decades. This is largely attributed to its ability for good areal coverage and continued development in sensor technologies. Carbon dioxide Capture and Storage (CCS) is an emerging climate change mitigation technology where monitoring is vital for its sustainability. This research investigates the use of spectral remote sensing imagery in detecting potential CO₂ occurrences at the surface, should a leakage occur from subsurface reservoirs where CO₂ is stored. Currently, there are no known leakages of CO₂ at industrial storage sites, therefore, this research was carried out at the Latera natural analogue site in Italy, in order to develop the methodology described. This paper describes the use of a popular probabilistic information fusion theory, referred to as the Dempster–Shafer theory of evidence, to analyse outlier pixels (anomalies). Outlier pixels are first determined using a new geostatistical image filtering methodology based on Intrinsic Random Function (IRF), Independent Component Analysis (ICA), and the industry standard parametric Reed–Xiaoli (RX) anomaly detection. Information fusion of detected outlier pixels and indirect surface effects of CO₂ leakage over time, such as stressed vegetation or mineral alterations, assigns a confidence measure per outlier pixel in order to identify potential leakage points. After visual validation using direct field measurements, it was demonstrated that the proposed methodology is able to detect majority of the seepage points at Latera, and holds promise as a new unsupervised CO₂ monitoring methodology.     

Lessons learned from natural and industrial analogues for storage of carbon dioxide

The deployment of CCS (carbon capture and storage) at industrial scale implies the development of effective monitoring tools. Noble gases are tracers usually proposed to track CO₂. This methodology, combined with the geochemistry of carbon isotopes, has been tested on available analogues.At first, gases from natural analogues were sampled in the Colorado Plateau and in the French carbogaseous provinces, in both well-confined and leaking-sites. Second, we performed a 2-years tracing experience on an underground natural gas storage, sampling gas each month during injection and withdrawal periods.In natural analogues, the geochemical fingerprints are dependent on the containment criterion and on the geological context, giving tools to detect a leakage of deep-CO₂ toward surface. This study also provides information on the origin of CO₂, as well as residence time of fluids within the crust and clues on the physico-chemical processes occurring during the geological story.The study on the industrial analogue demonstrates the feasibility of using noble gases as tracers of CO₂. Withdrawn gases follow geochemical trends coherent with mixing processes between injected gas end-members. Physico-chemical processes revealed by the tracing occur at transient state.These two complementary studies proved the interest of geochemical monitoring to survey the CO₂ behaviour, and gave information on its use.     

Chromatographic partitioning of impurities (H2S) contained in a CO2 stream injected into a deep saline aquifer: Part 2. Effects of flow conditions

Laboratory experiments reported in a companion paper were carried out to examine the chromatographic partitioning of impurities contained in a stream of CO₂ injected into a deep saline aquifer. The solubility of the impurity gas in the CO₂ stream compared to that of CO₂, the in situ conditions of pressure, temperature and water salinity, and the concentration of the impurity gas affect the partitioning of the two gases. For CO₂ streams containing H₂S, numerical simulations reported here have successfully replicated the laboratory results including the breakthrough of CO₂ ahead of H₂S. Sensitivity analysis performed with the numerical model has shown that flow conditions, controlled by such parameters as medium permeability, pressure gradient, dispersion, gas mobility and flow direction, affect the breakthrough time and separation of the two gases, leading to delayed or earlier breakthrough, and increasing or decreasing the time lag between the breakthrough of the two gases. Vertical bottom-up flow leads to earlier breakthrough, while top-down flow leads to delayed breakthrough. These results are important in establishing monitoring strategies at CO₂ storage sites and in evaluating the risks associated with the possible leakage of injected CO₂ that contains impurities.     

Coda-wave interferometry analysis of time-lapse VSP data for monitoring geological carbon sequestration

Injection and movement/saturation of carbon dioxide (CO₂) in a geological formation will cause changes in seismic velocities. We investigate the capability of coda-wave interferometry technique for estimating CO₂-induced seismic velocity changes using time-lapse synthetic vertical seismic profiling (VSP) data and the field VSP datasets acquired for monitoring injected CO₂ in a brine aquifer in Texas, USA. Synthetic VSP data are calculated using a finite-difference elastic-wave equation scheme and a layered model based on the elastic Marmousi model. A possible leakage scenario is simulated by introducing seismic velocity changes in a layer above the CO₂ injection layer. We find that the leakage can be detected by the detection of a difference in seismograms recorded after the injection compared to those recorded before the injection at an earlier time in the seismogram than would be expected if there was no leakage. The absolute values of estimated mean velocity changes, from both synthetic and field VSP data, increase significantly for receiver positions approaching the top of a CO₂ reservoir. Our results from field data suggest that the velocity changes caused by CO₂ injection could be more than 10% and are consistent with results from a crosswell tomogram study. This study demonstrates that time-lapse VSP with coda-wave interferometry analysis can reliably and effectively monitor geological carbon sequestration.     

Seismic detection of CO2 leakage along monitoring wellbores

A pilot carbon dioxide (CO₂) sequestration experiment was carried out in the Michigan Basin in which ～10,000 tonnes of supercritical CO₂ was injected into the Bass Island Dolomite (BILD) at 1050 m depth. A passive seismic monitoring (PSM) network was operated before, during and after the ～17-day injection period. The seismic monitoring network consisted of two arrays of eight, three-component sensors, deployed in two monitoring wells at only a few hundred meters from the injection point. 225 microseismic events were detected by the arrays. Of these, only one event was clearly an injection-induced microearthquake. It occurred during injection, approximately 100 m above the BILD formation. No events, down to the magnitude ?3 detection limit, occurred within the BILD formation during the injection. The observed seismic waveforms associated with the other 224 events were quite unusual in that they appear to contain dominantly compressional (P) but no (or extremely weak) shear (S) waves, indicating that they are not associated with shear slip on faults. The microseismic events were unusual in two other ways. First, almost all of the events occurred prior to the start of injection into the BILD formation. Second, hypocenters of the 94 locatable events cluster around the wells where the sensor arrays were deployed, not the injection well. While the temporal evolution of these events shows no correlation with the BILD injection, they do correlate with CO₂ injection for enhanced oil recovery (EOR) into the 1670 m deep Coral Reef formation that had been going on for ～2.5 years prior to the pilot injection experiment into the BILD formation. We conclude that the unusual microseismic events reflect degassing processes associated with leakage up and around the monitoring wells from the EOR-related CO₂ injection into the Coral Reef formation, ～700 m below the depth of the monitoring arrays. This conclusion is also supported by the observation that as soon as injection into the Coral Reef formation resumed at the conclusion of the BILD demonstration experiment, seismic events (essentially identical to the events associated with the Coral Reef injection prior to the BILD experiment) again started to occur close to a monitoring arrays. Taken together, these observations point to vertical migration around the casings of the monitoring wellbores. Detection of these unusual microseismic events was somewhat fortuitous in that the arrays were deployed at the depth where the CO₂ undergoes a strong volume increase during transition from a supercritical state to a gas. Given the large number of pre-existing wellbores that exist in depleted oil and gas reservoirs that might be considered for CO₂ sequestration projects, passive seismic monitoring systems could be deployed at appropriate depths to systematically detect and monitor leakage along them.     

Chromatographic partitioning of impurities contained in a CO2 stream injected into a deep saline aquifer: Part 1. Effects of gas composition and in situ conditions

A series of laboratory experiments were carried out to examine the chromatographic partitioning of impurities contained in a stream of CO₂ injected into a deep saline aquifer. The experiments were carried out under static (no flow) and dynamic conditions, mainly with H₂S as the impurity in the CO₂ stream, for 2%, 5% and 30% concentrations, and for in situ conditions of high pressure, temperature and water salinity, and also for pure water at a lower pressure and temperature. In addition, experiments were conducted using CH₄, N₂ and SO₂ at 5% concentration as the ‘Impurity’ in the CO₂ stream. The experiments show that gases in an impure stream of CO₂ being injected into a deep saline aquifer will chromatographically partition at the leading edge of the gas advancing through the water-saturated porous medium as a result of differential solubility in aquifer water. The solubility of the impurity gas in the CO₂ stream compared to that of CO₂ is the most dominant factor in regard to the breakthrough time and initial gas concentrations in the effluent. The in situ conditions of pressure, temperature and water salinity also affect the chromatographic partitioning of CO₂ and impurities contained in the injection stream through their general effect on the solubility of all gases. The concentration of the impurity gas in the feed gas stream has a secondary effect on the breakthrough and time lag decreasing with increasing concentration of the impurity gas. These experimental findings are significant for understanding the fate of the injected CO₂ and associated impurities contained in an injection stream, in devising monitoring procedures and protocols, and in developing emergency response plans in case of leakage of CO₂ and associated impurities.     

CO2 Capture with Membrane Contactors

This paper summarizes the development work for membrane gas/liquid contactors used for natural gas sweetening (CO₂ and H₂S removal), dehydration and CO₂ removal from exhaust gas. Membrane gas/liquid contactors operate with liquid on one side of a membrane and gas on the other. Unlike gas separation membranes, where differential pressure across the membrane provides the driving force for separation, here the pressure is essentially the same on both sides of the membrane. Absorption into the liquid provides the driving force. The increased specific area of the membrane gas/liquid contactor allows for a 65-75% reduction in weight and size compared to conventional towers. The latest work has been a gas dehydration field test at a Duke Energy Field Services compressor station in Colorado. The project was performed in co-operation with Gas Technology Institute (GTI).     

Role and impact of CO2–rock interactions during CO2 storage in sedimentary rocks

Before implementing CO₂ storage on a large scale its viability regarding injectivity, containment and long-term safety for both humans and environment is crucial. Assessing CO₂–rock interactions is an important part of that as these potentially affect physical properties through highly coupled processes. Increased understanding of the physical impact of injected CO₂ during recent years including buoyancy driven two-phase flow and convective mixing elucidated potential CO₂ pathways and indicated where and when CO₂–rock interactions are potentially occurring. Several areas of interactions can be defined: (1) interactions during the injection phase and in the near well environment, (2) long-term reservoir and cap rock interactions, (3) CO₂–rock interactions along leakage pathways (well, cap rock and fault), (4) CO₂–rock interactions causing potable aquifer contamination as a consequence of leakage, (5) water–rock interactions caused by aquifer contamination through the CO₂ induced displacement of brines and finally engineered CO₂–rock interactions (6). The driving processes of CO₂–rock interactions are discussed as well as their potential impact in terms of changing physical parameters. This includes dissolution of CO₂ in brines, acid induced reactions, reactions due to brine concentration, clay desiccation, pure CO₂–rock interactions and reactions induced by other gases than CO₂. Based on each interaction environment the main aspects that are possibly affecting the safety and/or feasibility of the CO₂ storage scheme are reviewed and identified. Then the methodologies for assessing CO₂–rock interactions are discussed. High priority research topics include the impact of other gaseous compounds in the CO₂ stream on rock and cement materials, the reactivity of dry CO₂ in the absence of water, how CO₂ induced precipitation reactions affect the pore space evolution and thus the physical properties and the need for the development of coupled flow, geochemical and geomechanical models.     

Capture of carbon dioxide from flue or fuel gas mixtures by clathrate crystallization in a silica gel column

A column of silica gel was employed to contact water with flue gas (CO₂/N₂) mixture to assess if CO₂ can be separated by hydrate crystallization. Three different silica gels were used. One with a pore size of 30 nm (particle size 40–75 μm) and two with a pore size of 100 nm and particle sizes of 40–75 and 75–200 μm respectively. The observed trends indicate that larger pores and particle size increase the gas consumption, CO₂ recovery, separation factor and water conversion to hydrate. Thus, the gel (gel #3) with the larger particle size and larger pore size was chosen to carry out experiments with concentrated CO₂ mixtures and for experiments in the presence of tetrahydrofuran (THF), which itself is a hydrate forming substance. Addition of THF reduces the operating pressure in the crystallizer but it also reduces the gas uptake. Gel #3 was also used in experiments with a fuel gas (CO₂/H₂) mixture in order to recover CO₂ and H₂. It was found that the gel column performs as well as a stirred reactor in separating the gas components from both flue gas and fuel gas mixtures. However, the crystallization rate and hydrate yield are considerably enhanced in the former. Finally the need for stirring is eliminated with the gel column which is enormously beneficial economically.     

CO2 storage and enhanced coalbed methane recovery: Reservoir characterization and fluid flow simulations of the Big George coal,Powder River Basin,Wyoming, USA

Coalbeds are an attractive geological environment for storage of carbon dioxide (CO₂) because CO₂ is retained in the coal as an adsorbed phase and the cost of injection can be offset by enhanced coalbed methane (ECBM) production. This paper presents the findings of a CO₂ storage feasibility study on coalbeds in the Wyodak-Anderson coal zone of the Powder River Basin, Wyoming, USA, using reservoir characterization and fluid flow simulations. A 3D numerical model of the Big George coal was constructed using geostatistical techniques, with values of cleat and matrix permeability and porosity constrained through history-matching of production data from coalbed methane (CBM) wells in the field area.Following history-matching, several ECBM and CO₂ storage scenarios were investigated: shrinkage and swelling of the coal was either allowed or disallowed, a horizontal hydraulic fracture was either placed at the injection well or removed from the model, the number of model layers was varied between 1 and 24, and the permeability and porosity fields were constructed to be either homogeneous or heterogeneous in accordance with geostatistical models of regional variability. All simulations assumed that the injected gas was 100% CO₂ and that the coalbed was overlain by an impermeable caprock. Depending on the scenario, the simulations predicted that after 13 years of CO₂ injection, the cumulative methane production would be enhanced by a factor of 1.5–5. Including coal matrix shrinkage and swelling in the model predicted swelling near the injection well, which resulted in a slight reduction (10%) in injection rate. However, including a horizontal hydraulic fracture in the model at the base of the injection well helped mitigate the negative effect of swelling on injection rate. It was also found that six model layers were needed to have sufficient resolution in the vertical direction to account for the buoyancy effects between the gas and resident water, and that capturing the heterogeneous nature of the coal permeability and porosity fields predicted lower estimates of the storage capacity of the Wyodak-Anderson coal zone.After noting that gravity and buoyancy were the major driving forces behind gas flow within the Big George coal, several leakage scenarios were also investigated, in an effort to better understand the interplay between diffusion and flow properties on the transport and storage of CO₂. The modeling predicted that the upward migration of gas due to the buoyancy effect was faster than the diffusion of CO₂ and therefore the gas rapidly rose to the top of the coalbed and migrated into overlying strata when an impermeable caprock was not included in the model.     

CO2 transportation for carbon capture and storage: Sublimation of carbon dioxide from a dry ice bank

Climate change is being caused by greenhouse gases such as carbon dioxide (CO₂). Carbon capture and storage (CCS) is of interest to the scientific community as one way of achieving significant global reductions of atmospheric CO₂ emissions in the medium term. CO₂ would be captured from large stationary sources such as power plants and transported via pipelines under high pressure conditions to underground storage. If a downward leakage from a surface transportation system module occurs, the CO₂ would undergo a large temperature reduction and form a bank of “dry ice” on the ground surface; the sublimation of the gas from this bank represents an area source term for subsequent atmospheric dispersion, with an emission rate dependent on the energy balance at the bank surface. Gaseous CO₂ is denser than air and tends to remain close to the surface; it is an asphyxiant, a cerebral vasodilator and at high concentrations causes rapid circulatory insufficiency leading to coma and death. Hence a subliming bank of dry ice represents safety hazard. A model is presented for evaluating the energy balance and sublimation rate at the surface of a solid frozen CO₂ bank under different environmental conditions. The results suggest that subliming gas behaves as a proper dense gas (i.e. it remains close to the ground surface) only for low ambient wind speeds.     

Continuous operation of the potassium-based dry sorbent CO2 capture process with two fluidized-bed reactors

The dry sorbent CO₂ capture process is an advanced concept to efficiently remove CO₂ from flue gas with two fluidized-bed reactors. This paper summarizes the results of performance of the two fluidized-bed reactors in the continuous solid circulation mode to investigate the feasibility of using potassium carbonate-based solid sorbent (Sorb KX35). The parameters such as gas velocity, solid circulation, carbonation temperature, and water vapor content were investigated during several continuous operations of two fluidized-bed reactors. The CO₂ removal increased as gas velocity was decreased and as solid circulation rate was increased. The CO₂ removal ranged from 26% to 73% was rather sensitive to the water vapor content among other parameters. A 20 h continuous operation conducted in a bench scale fast fluidized-bed reactor system indicated that the spray-dried potassium-based sorbent, Sorb KX35 having superior attrition resistance and high bulk density, had a promising CO₂ removal capacity of 50–73% at steady state and was able to regenerate and reuse. The results from this work are good enough to prove the concept of the dry sorbent CO₂ capture process to be one of viable methods for capturing CO₂ from dilute flue gas of fossil fuel-fired power plants.     

ELEVATED ATMOSPHERIC CO2 INCREASES WATER AVAILABILITY IN A WATER-LIMITED GRASSLAND ECOSYSTEM1

ABSTRACT: Californian annual grassland on sandstone (moderately fertile) and serpentine (very infertile) soils at the Jasper Ridge Biological Preserve, Stanford, California, were exposed to ambient or elevated (ambient + 36 Pa CO₂) atmospheric CO₂ in open-top chambers since December 1991. We measured ecosystem evapotranspiration with open gas-exchange systems, and soil moisture with time-domain reflectometry (TDR) over 0–15 cm (serpentine) and 0–30 cm (sandstone) depths, at times of peak above ground physiological activity. Evapotranspiration decreased by 12 to 63 percent under elevated CO₂ in three consecutive years in the sandstone ecosystem (p = 0.053, p = 0.162, p = 0.082 in 1992, 1993, and 1994, respectively). In correspondence with decreased evapotranspiration, late-season soil moisture reserves in the sandstone were extended temporally by 10 ± 3 days in 1993 and by 28 ± 11 days in 1994. The effect of elevated CO₂ on soil moisture was greater in the drier spring of 1994 (419 mm annual rainfall) than in 1993 (905 mm annual rainfall). In the serpentine ecosystem, evapotranspiration and soil moisture reserves were not clearly affected by elevated CO₂. Soil water may be conserved in drought-affected ecosystems exposed to elevated CO₂, but the amount of conservation appears to depend on the relative importance of transpiration and soil evaporation in controlling water flux.     

Evaluating geological sequestration of CO2 in bituminous coals: The southern Sydney Basin,Australia as a natural analogue

Carbon dioxide contents of coals in the Sydney Basin vary both aerially and stratigraphically. In places, the coal seam gas is almost pure CO₂ that was introduced from deep magmatic sources via faults and replaced pre-existing CH₄. In some respects this process is analogous to sequestration of anthropogenic CO₂. Laboratory studies indicate that CO₂:CH₄ storage capacity ratios for Sydney Basin coals are up to ∼2 and gas diffusivity is greater for CO₂ by a factor of up to 1.5.Present-day distribution of CO₂ in the coals is controlled by geological structure, depth and a combination of hydrostatic and capillary pressures. Under present-day P–T conditions, most of the CO₂ occurs in solution at depths greater than about 650 m; at shallower depths, larger volumes of CO₂ occur in gaseous form and as adsorbed molecules in the coal due to rapidly decreasing CO₂ solubility. The CO₂ has apparently migrated up to structural highs and is concentrated in anticlines and in up-dip sections of monoclines and sealing faults. CO₂ sequestered in coal measure sequences similar to those of the Sydney Basin may behave in a similar way and, in the long term, equilibrate according to the prevailing P–T conditions.In situ CO₂ contents of Sydney Basin coals range up to 20 m³/t. Comparisons of adsorption isotherm data measured on ground coal particles with in situ gas contents of Sydney Basin coals indicate that the volumes of CO₂ stored do not exceed ∼60% of the total CO₂ storage capacity. Therefore, the maximum CO₂ saturation that may be achieved during sequestration in analogous coals is likely to be considerably lower than the theoretical values indicated by adsorption isotherms.     

CO2 removal using membrane gas absorption

The objective of this study is to investigate the potential process for the removal of carbon dioxide (CO₂) from flue gas using fundamental membrane contactor, which is a membrane gas absorption (MGA) system. The experiments consisted of microporous polyvinylidenefluoride (PVDF) flat sheet membrane with 0.1 μm (as module I) and 0.45 μm (as module II) pore size. 2-Amino-2-methyl-1-propanol (AMP) solution was employed as the liquid absorbent. The effect of AMP concentration was studied with variation in the range 1–5 M. In addition, the experiments were carried out with 10%, 20%, 30% and 40% gas ratio of CO₂ to N₂ and pure CO₂ as well. Through contact angle measurement, membranes for module I and module II were obtained with CA values of around 130.25° and 127.77°, respectively. The mass transfer coefficients for module II are lower than those of module I for 1–5 M of AMP. Furthermore, the increase in CO₂ concentration in the feed gas stream enhanced the CO₂ flux as the driving force of the system was increased in sequence from 1 M to 5 M of AMP. However, after the particular percentage (40%) of CO₂ inlet concentration, the CO₂ fluxes seem saturated. The combination of AMP as liquid absorbent and PVDF microporous membrane in MGA system has shown the potential to remove the CO₂ from flue gas. In addition, the higher AMP concentration gave higher mass transfer coefficient at low liquid flow rates.     

A solution against well cement degradation under CO2 geological storage environment

Capturing and storing carbon dioxide (CO₂) underground for thousands of years is one way to reduce atmospheric greenhouse gases, often associated with global warming. Leakage through wells is one of the major issues when storing CO₂ in depleted oil or gas reservoirs. CO₂-injection candidates may be new wells, or old wells that are active, closed or abandoned. In all cases, it is critical to ensure that the long-term integrity of the storage wells is not compromised. The loss of well integrity may often be explained by the geochemical alteration of hydrated cement that is used to isolate the annulus across the producing/injection intervals in CO₂-related wells. However, even before any chemical degradation, changes in downhole conditions due to supercritical CO₂ injections can also be responsible for cement debonding from the casing and/or from the formation, leading to rapid CO₂ leakage. A new cement with better CO₂ resistance is compared with conventional cement using experimental procedure and methodology simulating the interaction of set cement with injected, supercritical CO₂ under downhole conditions. Geochemical experimental data and a mechanical modeling approach are presented. The use of adding expanding property to this new cement to avoid microannulus development during the CO₂ injection is discussed.     

Integration of CO2 capture unit using single- and blended-amines into supercritical coal-fired power plants: Implications for emission and energy management

This work provides the essential information and approaches for integration of carbon dioxide (CO₂) capture units into power plants, particularly the supercritical type, so that energy utilization and CO₂ emissions can be well managed in the subject power plants. An in-house model, developed at the University of Regina, Canada, was successfully used for simulating a 500 MW supercritical coal-fired power plant with a post-combustion CO₂ capture unit. The simulations enabled sensitivity and parametric study of the net efficiency of the power plant, the coal consumption rate, and the amounts of CO₂ captured and avoided. The parameters of interest include CO₂ capture efficiency, type of coal, flue gas delivery scheme, type of amine used in the capture unit, and steam pressure supplied to the capture unit for solvent regeneration. The results show that the advancement of MEA-based CO₂ capture units through uses of blended monoethanolamine–methyldiethanolamine (MEA–MDEA) and split flow configuration can potentially make the integration of power plant and CO₂ capture unit less energy intensive. Despite the increase in energy penalty, it may be worth capturing CO₂ at a higher efficiency to achieve greater CO₂ emissions avoided. The flue gas delivery scheme and the steam pressure drawn from the power plant to the CO₂ capture unit should be considered for process integration.     

Assessment of the different parameters affecting the CO2 purity from coal fired oxyfuel process

The oxyfuel process is one of the most promising options to capture CO₂ from coal fired power plants. The combustion takes place in an atmosphere of almost pure oxygen, delivered from an air separation unit (ASU), and recirculated flue gas. This provides a flue gas containing 80–90 vol% CO₂ on a dry basis. Impurities are caused by the purity of the oxygen from the ASU, the combustion process and air ingress. Via liquefaction a CO₂ stream with purity in the range from 85 to 99.5 vol% can be separated and stored geologically. Impurities like O₂, NO_X, SO_X, and CO may negatively influence the transport infrastructure or the geological storage site by causing geochemical reactions. Therefore the maximum acceptable concentrations of the impurities in the separated CO₂ stream must be defined regarding the requirements from transportation and storage. The main objective of the research project COORAL therefore is to define the required CO₂ purity for capture and storage.     

Influence of Landfill Gas on the Microdistribution of Grass Establishment Through Natural Colonization

Many revegetated landfills have poor cover including bare areas where plants do not grow. This study, on the Bisasar Road Landfill site in South Africa, assessed grass species preferences to microhabitat conditions in a mosaic of patches of well-established grassed areas and bare, nonvegetated areas. Factors, including soil CO₂, CH₄, O₂, nutrients, and other general soil conditions, were measured in relation to species distribution and grass biomass in the field. Cynodon dactylon was the dominant grass in the established grass areas but was less abundant in the areas bordering the bare areas where Paspalum paspalodes and Sporobolus africanus were common. A number of soil factors measured were significantly correlated with grass biomass and these included Mg, Ca, Zn, Mn, K, temperature, moisture, and CO₂. However, a laboratory bioassay using the growth of C. dactylon with soils removed from the landfill indicated that there were no differences in the soils from the bare areas and those that supported high plant biomass. Thus, no nutrient deficiency or chemical toxicity was inherent in the soil in the laboratory. The results of the field investigation and bioassay indicated that soil CO₂ as a result of landfill gas infiltration into the root zone was probably the main factor causing bare areas on the landfill where no grass species could colonize and grow and that C. dactylon was more sensitive to elevated soil CO₂ than other grass species such as P. paspalodes and S. africanus.     

Application of crosswell seismic tomography using difference analysis with data normalization to monitor CO2 flooding in an aquifer

A pilot-scale experiment for carbon dioxide (CO₂) sequestration was undertaken at the Nagaoka test field in Japan. Time-lapse crosswell seismic tomography was conducted to detect and monitor the movement of CO₂ injected into an aquifer. We applied difference analysis with data normalization (DADN) to the time-lapse data to eliminate false images that were apparent in a conventionally processed difference section. Conventional difference analysis calculates travel-time delays after inversion, whereas the DADN method calculates them from raw travel-time records before inversion. Thus, fewer errors are generated with the DADN method compared to a conventional inversion analysis. We applied the DADN method to time-lapse tomography data recorded before and after the injection of CO₂ and computed the velocity variation in a subsurface section, which clearly showed the distribution of CO₂ flooding within a high permeability zone in the aquifer and showed no CO₂ leakage into the caprock. Our results also show the maximum velocity decrease as a result of CO₂ injection was about 9%, which is close to the results obtained in laboratory experiments. Finally, numerical simulations were inverted to test the effectiveness of the conventional and DADN methods in dealing with noise. These tests showed that the DADN method effectively reduces unique coherent noise for particular receiver and source combinations. We concluded that the DADN method provides useful data for monitoring the flow of CO₂ sequestered in underground aquifers.