Effect of injection timing,injector opening pressure and nozzle geometry on the performance of a compression ignition engine operated on non-edible oil methyl esters from different sources

Increasing cost of fossil fuels, environmental threats from exhaust emissions and their depleting nature have generated intense international interest in developing renewable and alternative fuels for internal combustion engines. This study investigates the suitability of different non-edible-derived biodiesels such as cottonseed oil methyl ester (COME), honne oil methyl ester (HnOME) and honge oil methyl ester (HOME) to four-stroke, single-cylinder compression ignition (CI) engine. Engine tests were conducted to study the effect of fuel injection timing (IT), fuel injector opening pressure (IOP) and injector nozzle geometry on the performance, combustion and emission characteristics of COME, HnOME and HOME in the modified CI engine. IT was varied from 19° to 27° before top dead centre (bTDC) in steps of 4° bTDC; IOP was varied from 205 to 240 bar in steps of 10 bar. Nozzle injectors of three to five holes, each of 0.3 mm size, were selected for the study. It was concluded that a retarded IT of 19° bTDC increased IOP of 230 bar, and four-hole nozzle injector of 0.3 mm size resulted in overall better engine performance with increased brake thermal efficiency and reduced hydrocarbon and carbon monoxide smoke emissions for the fuels tested.     

Effects of injection timing,injector opening pressure and nozzle geometry on the performance of cottonseed oil methyl ester-fuelled diesel engine

Increasing petroleum prices, increasing threat to the environment from exhaust emissions and global warming have generated intense international interest in developing renewable and alternative non-petroleum fuels for engines. Evolving technology and a recurring energy crisis necessitates a continuous investigation into the search for sustainable and clean-burning renewable fuels. In this paper, cottonseed oil methyl ester (COME) was used in a four-stroke, single-cylinder variable compression ratio diesel engine. Tests were carried out to study the effects of fuel injection timing, fuel injector opening pressure (IOP) and injector nozzle geometry on the performance and combustion of COME biodiesel fuel used in a compression ignition engine with a single fuel mode. Fuel injection timing varied from 19° to 27° before top dead centre (bTDC) in incremental steps of 4° bTDC; fuel IOP varied from 210 to 240 bar in incremental steps of 10 bar. Fuel nozzle injectors with three, four and five holes, each of 0.3 mm size, were selected for the study. The results suggested that with retarded injection timing of 19° bTDC, increased IOP of 230 bar and a four-hole nozzle injector of 0.3 mm size resulted in overall better engine performance with an increased brake thermal efficiency and reduced HC, CO and smoke emission levels.     

Effect of hydrogen addition to CNG in a biodiesel-operated dual-fuel engine

Alternative fuels for diesel engine applications are gaining more prominence as they have numerous advantages compared to fossil fuels. They are renewable, biodegradable; provide food and energy security and foreign exchange savings. They address environmental concerns and socio-economic issues as well. Gaseous fuels such as compressed natural gas and hydrogenated compressed natural gas (HCNG) appear more attractive fuels for diesel engine applications operated in dual-fuel mode. Such dual fuel engines can replace considerable amount of liquid-injected pilot fuels by gaseous fuels besides being friendly to the environment. A small quantity of liquid fuel injected towards the end of the compression stroke initiates combustion of the inducted gas in the dual-fuel engines. The main advantage of dual-fuel engines is their lower nitrogen oxides (NO_x) and particulate emissions. Hence renewable fuels such as biodiesels and gaseous fuels can be used predominantly for transportation and power generation applications. Gaseous fuels are clean burning and are more economical as well. A suitable carburettor was designed to supply a stoichiometric mixture of air and HCNG to the modified diesel engine operated in dual-fuel mode. The biodiesel used in this study is derived from Honge oil called the Honge oil methyl ester (HOME). This paper presents the performance, combustion and exhaust emission characteristics of a single cylinder, four stroke, direct injection, stationary diesel engine operated on HOME and HCNG in dual-fuel mode. From the results it is observed that HOME–HCNG combination gave lower brake thermal efficiency (BTE) and improved emission levels when compared with diesel/HOME in single fuel operation. Lower smoke and particulate matter were obtained with dual-fuel operation. Comparative measures of BTE, peak pressure, pressure–crank angle variation, smoke opacity, hydrocarbon, carbon monoxide and NO_x emissions have been made and analysed.     

Performance studies of a low heat rejection engine operated on non-volatile vegetable oils with exhaust gas recirculation

During recent decades, considerable effort has been expended world-wide to reduce dependency on petroleum fuels for power generation and transportation through the search for suitable alternative fuels that are environmentally friendly. In this respect, vegetable oils are a promising alternative to diesel fuel. However, the high viscosity, poor volatility and cold flow characteristics of vegetable oils can cause some problems such as injector coking, severe engine deposits, filter gumming and piston ring sticking and thickening of lubrication from long-term use in diesel engines. These problems can be eliminated or minimised by transesterification of the vegetable oils to form monoesters. Although transesterification improves the fuel properties of vegetable oil, the viscosity and volatility of biodiesel are still worse than those of petroleum diesel fuel. The performance of a diesel engine with such biodiesel operation can be improved further with the concept of the low heat rejection (LHR) engine. In the LHR engine, combustion surfaces on the pistons, cylinder walls and valves can be coated with ceramic materials. The objective of this study was to apply the LHR engine concept for improving engine performance when either honge biodiesel, known as honge oil methyl ester (HOME), or neem biodiesel, known as neem oil methyl ester (NOME) oils was used as an alternative fuel. For this purpose, experiments were conducted on a single cylinder, four-stroke, direct injection, water-cooled compression ignition engine using diesel, HOME and NOME oils at different injection timings of 19, 23 and 27° before top dead centre (BTDC) with and without the induction of exhaust gas recirculation (EGR). The percentage of EGR was varied from 5 to 20% in steps of 5%. The results showed that specific fuel consumption and brake thermal efficiency were improved for both of the biodiesel fuels in the LHR engine. An EGR of 10% resulted in better performance with trade-off between oxides of nitrogen and hydrocarbons/carbon monoxide emissions and hence 10% EGR is taken as the best of the range from 5 to 20%. However, readings with other EGR ratios are not reported.     

Combustion and emission characteristics of a direct injection CI engine when operated on Marotti oil methyl ester and blends of Marotti oil methyl ester and diesel

This paper presents a feasibility study of Marotti oil biodiesel as an alternative to diesel fuel for a compression ignition engine. Marotti oil is inedible and available mainly in the state of Kerala. The oil is extracted from Marotti seeds. However, the high viscosity, poor volatility and cold flow characteristics of many vegetable oils in general, and Marotti oil in particular, can cause problems such as injector coking, severe engine deposits, filter gumming, piston ring sticking and thickening of lubrication from long-term use in diesel engines. These problems can be eliminated or minimised by transesterification of the vegetable oils to form monoesters. Although transesterification improves the fuel properties of vegetable oil, the viscosity and volatility of biodiesel are still worse than for petroleum diesel fuel. Subsequently, Marotti oil was converted into its methyl ester by the process of transesterification. The methyl ester was blended with diesel in various proportions to obtain different blends of Marotti oil with diesel. The performance, emission and combustion characteristics of Marotti methyl ester and its blends with diesel were studied and the results were compared with the base line data generated for diesel operation. Experiments were conducted using an injection timing of 23° before top dead centre (BTDC) and an injection pressure of 205 bar at various power outputs and at a constant rated speed of 1500 rpm. The engine manufacturer specifies an injection timing of 23° BTDC and injection pressure of 205 bar for the standard diesel fuel operation. The heat release rates, maximum rate of pressure rise, ignition delay and combustion duration for these fuel combinations were obtained.

From the results obtained, it was observed that the biodiesel produced from Marotti oil and its blends with diesel have slightly reduced brake thermal efficiency and increased smoke, hydrocarbon, carbon monoxide and reduced NO _x emissions compared with diesel-only operation. The investigation showed that the B20 biodiesel blend of Marotti oil with diesel produced better performance in terms of higher brake thermal efficiency, lower specific fuel consumption and comparatively lower emissions compared to the other blend ratios considered.     

Blends of karanja and jatropha biodiesels for diesel engine applications

Over a number of years, the work of exploring different biodiesels as an alternative to diesel fuel has been carried out worldwide. Not much focus on the use of combination of different biodiesels and their behaviour in diesel engines has been reported. This work is an attempt in this direction, which reports on the use of combination of biodiesels derived from jatropha and karanja oils. Jatropha oil methyl ester (JOME) and honge oil methyl ester (HOME) represent the respective biodiesels derived from these non-edible oils. Experiments were conducted on a four-stroke, single-cylinder diesel engine using these biodiesel combinations in order to check their feasibility as alternative fuels to diesel. Initially, experiments were conducted on each biodiesel and their blends with diesel and engine parameters were optimised in terms of injection pressure and injection timing. Advancing the injection timing improved the overall performance of the engine fuelled with JOME while retarding the injection timing favoured the HOME. Both biodiesels performed better with an injector opening pressure of 230 bar. Finally, experiments were conducted with the combination of both biodiesels with different blend ratios. It was observed that increasing the JOME content in the biodiesels blend improved the performance with reduced emissions of smoke, hydrocarbons and carbon monoxide emissions. However NO _x emission increased.     

Effect of mixing chamber venturi,injection timing,compression ratio and EGR on the performance of dual-fuel engine operated with HOME and CNG

Stringent environmental policies and the ever increasing demand for energy have triggered interest in novel combustion technologies that use alternative fuels as energy sources. Of these, pilot-ignited compressed natural gas (CNG) engines that employ small biodiesel pilot to ignite a premixed natural gas–air mixture have received considerable attention. This paper discusses the effect of mixing chamber venturi, injection timing, compression ratio and exhaust gas recirculation (EGR) on the performance of dual-fuel engine operated on biodiesel derived from honge oil and is called honge oil methyl ester (HOME) and CNG. The proposed study mainly focuses on the manifold induction of CNG along with HOME injection. However, CNG can also be injected using port or direct gas injector (Lakshmanan and Nagarajan 2010, Energy 35, pp. 3172–3178). The future study will involve these methods of CNG injection. From this study, it is concluded that an advanced injection timing and an increased compression ratio resulted in increased brake thermal efficiency and reduced smoke, hydrocarbons and carbon monoxide emissions. However, nitrogen oxides (NO _x ) emission increased significantly. The increased NO _x emission was effectively reduced with EGR method. A mixing chamber venturi of 3 mm size, injection timing of 27° before top dead centre (BTDC), compression ratio of 17.5 and 10% EGR were found to be optimum for the modified compression ignition engine that was operated on CNG–HOME dual-fuel mode.     

Effects of EGR,swirl augmentation techniques on combustion of biodiesel/ethanol and their blends in a diesel engine

The diminishing resources and continuously increasing cost of petroleum in association with their alarming pollution levels from diesel engines have caused an interest in finding alternative fuels to diesel which are renewable and sustainable. Emission control and engine efficiency are two most important parameters in current engine design. The impending introduction of emission standards such as Euro IV and Euro V is forcing the research towards developing new technologies for combating engine emissions. The classification of Euro IV and V norms is applicable to heavy-duty engines in Europe, where as Euro 5 is applicable to light-duty engines. This paper presents the effects of exhaust gas recirculation (EGR), swirl augmentation techniques and ethanol addition on the combustion of Honge oil methyl ester (HOME) and its blends with ethanol in a diesel engine. From the experimental work conducted, it is found that the combustion of HOME plus up to 15% ethanol blend in a diesel engine operated with optimised parameters of injection timing 23° Before Top Dead Centre and compression ratio 17.5 results in acceptable combustion emissions and improved brake thermal efficiency (BTE). The addition of ethanol increased BTE with reduced hydrocarbons (HCs), CO and smoke emissions. However, NO _x emissions increased dramatically. Use of appropriate EGR reduces NO _x to acceptable levels. The implementation of swirl augmentation techniques further resulted in increased BTE and considerable reduction in tail pipe emissions such as smoke, HCs, CO and NO _x . The effect of swirl by providing grooves on the piston was taken into consideration to find the overall biodiesel engine performance, which gives scope for further studies.     

Effect of bioethanol and thermal barrier coating on the performance of dual fuel engine operating on Honge oil methyl ester (HOME) and producer gas induction

Alternative fuels have numerous advantages compared to fossil fuels as they are renewable, biodegradable; provide energy security and foreign exchange saving besides addressing environmental concerns and socio-economic issues as well. Renewable fuels can be used predominantly as fuel for both transportation and power generation applications. Improved engine performance with reduced engine exhaust emissions is a major research objective in engine development. Today, the use of biomass derived producer gas is more relevant for addressing rural power generation and is a promising technique for controlling both nitric oxide (NO_x) and soot emission levels. In view of this, exhaustive experiments on the use of Honge oil methyl ester (HOME)–Producer gas in a dual fuel engine have been carried out with an intension of improving its fuel efficiency. This paper mainly presents results on a single cylinder four stroke direct injection diesel engine operated in dual fuel mode using HOME–Producer gas combination with and without bio-ethanol addition and thermal barrier coating (TBC). Further, the results were compared with diesel–producer gas mode of operation. Experimental investigation on dual fuel operation using HOME+5% bioethanol (BE5)–Producer gas operation with TBC showed 12.35% increased brake thermal efficiency with decreased hydrocarbon and carbon monoxide emissions and increased NO_x emission levels compared to HOME–Producer gas mode of operation.     

Performance,combustion and emission characteristics of a single-cylinder,four-stroke,direct injection diesel engine operated on a dual-fuel mode using Honge oil methyl ester and producer gas derived from biomass feedstock of different origin

Renewable and alternative fuels have numerous advantages compared with fossil fuels, as they are renewable and biodegradable, and provide food and energy security and foreign exchange savings besides addressing environmental concerns and socio-economic issues. In this context, present work was carried out to investigate the feasibility of alternative and renewable fuels derived from biomass feedstock of different origin for engine applications. The present study was also extended to study the effect of producer gas composition derived from different biomass feedstock on the performance, combustion and emission characteristics of a single-cylinder, four-stroke, direct injection stationary diesel engine operated on a dual-fuel mode using Honge oil methyl ester (HOME) and producer gas induction. The performance of the engine was evaluated with a constant injection timing of 27° before top dead centre, an injection pressure of 205 bar for the diesel–producer gas combination and 230 bar for the HOME–producer gas combination and a compression ratio of 17.5. The results showed that the performance of the dual-fuel engine varies with the composition of the producer gas and depends on the type of biomass feedstock used in the gasifier. Experimental investigations on the dual-fuel engine showed that brake thermal efficiency values for the engine operated using HOME–producer gas derived from babul, neem and honge woods were found to be 17.2, 14.3 and 11.56% respectively, compared to 23.8% for diesel–producer gas operation at 80% load. However, the results showed better engine performance with lower exhaust emission levels for the operation of HOME–producer gas derived from the ordinary or babul wood compared with the operation of that derived from the neem and Honge woods. In view of this, present study reveals that use of alternative and renewable fuels for dual fuel engine can be considered as an immediate solution for the development of rural areas and emergency use in the event of severe diesel fuel shortage.     

Studies on the use of low-volatile non-edible oils in a thermal barrier-coated diesel engine

Owing to the ever-increasing vehicle population, the consumption of diesel fuel in the transportation, agricultural and industrial sectors has increased at an alarming rate. This has led to rapid fossil fuel depletion, ozone depletion and environmental degradation, which have become a serious concern. Search for alternative renewable and clean energy fuel sources to mitigate the emissions of greenhouse gases is continuing, and attempts to find different techniques for efficient utilization of these fuels are also undertaken. Biodiesel being an oxygenated fuel obtained from vegetable oils has received greater attention over the years as a promising alternative to diesel fuel. However, vegetable oils exhibit high viscosity, poor volatility and poor cold-flow characteristics. These characteristics can cause the following problems in the engine when run for a longer duration: injector coking, severe engine deposits, filter gumming, piston ring sticking and thickening of lubrication. These problems can be eliminated or minimized by adopting suitable fuel processing techniques to obtain biodiesels from vegetable oils. The fuel processing techniques vary widely, which include transesterification, supercritical methanolysis, ultrasonic and continuous microwave-assisted transesterification methods. In the present study, the transesterification method is effectively used to obtain biodiesels from non-edible oils of honne and cotton seed. The biodiesels obtained from these oils were used in the unmodified diesel engine to check their feasibility as diesel engine alternatives. Different thermal barrier coatings (TBCs) were applied on the piston, cylinder head, and inlet and exhaust valve surfaces of the diesel engine in order to make it a fully adiabatic engine. The engine with such TBCs is called a low heat rejection engine. For the present study, the TBC of partially stabilized zirconia (PSZ) and aluminium oxide (Al₂O₃) were selected. Finally, the performance of the diesel engine fuelled with different biodiesels in both conventional and thermal barrier-coated modes was compared. The thermal barrier-coated engine with the PSZ version showed better performance with increased nitric oxide emissions when compared with the Al₂O₃ coating.     

Fuel efficiency enhancement of modified diesel engine operated in dual fuel mode using renewable and sustainable fuels

ABSTRACT

Renewable and sustainable fuels for diesel engine applications provide energy protection, overseas exchange saving and address atmospheric and socio-economic concerns. This study presents the investigational work carried out on a single cylinder, four-stroke, direct injection diesel engine operated in dual fuel (DF) mode using renewable and sustainable fuels. In the first phase, a Y-shaped mixing chamber or venture was developed with varied angle facility for gas entry at 30°, 45° and 60°, respectively, to enable homogeneous air and gas mixing. Further effect of different gas and air mixture entry on the DF engine performance was studied. In the next phase of the work, hydrogen flow rate influence on the combustion and emission characteristics of a compression ignition (CI) engine operated in DF mode using diesel, neem oil methyl ester (NeOME) and producer gas has been investigated. During experimentation, hydrogen was mixed in different proportions varied from 3 to 12 l/min (lpm) in step of 3 lpm along with air-producer gas and the mixtures were directly inducted into engine cylinder during suction stroke. Experimental investigation showed that 45° Y-shaped mixing chamber resulted in improved performance with acceptable emission levels. Further, it is observed that investigation showed that at maximum operating conditions and hydrogen flow rate of 9 lpm, Diesel–producer gas and NeOME–producer gas combination showed increased thermal efficiency by 13.2% and 3.8%, respectively, compared to the DF operation without hydrogen addition. Further, it is noticed that hydrogen-enriched producer gas lowers the power derating by 5–10% and increases nitric oxide (NO_x) emissions. However, increased hydrogen addition beyond the 12 lpm leads to sever knocking.

Abbreviations: NeOME: Neem oil methyl ester; BTE: brake thermal efficiency; CI: compression ignition; ITE: indicated thermal efficiency; PG: producer gas; CA: crank angle; K: Kelvin; BP: brake power; IP: indicated power; H₂: hydrogen; HC: unburnt hydrocarbon; CO: carbon dioxide; CO₂: carbon dioxide; NO_x: nitric oxide; HRR: heat release rate; %: percentage; PPM: parts per million; CMFIS: conventional mechanical fuel injection system.     

Thermal barrier coated diesel engine running on biodiesel: a review

Thermal barrier coated diesel engine, also known as low heat rejection (LHR) engine have offered the promise of reducing heat rejection to the engine coolant and increase the combustion temperature which results in increase of thermal efficiency, decrease of fuel consumption and emission rate of the engine. Biodiesel derived from the vegetable oils are a promising alternative fuel for diesel fuel. The viscosity of vegetable oil after transestrification is still higher than that of diesel fuel. The various researchers have reported that the energy of the biodiesel could be released more efficiently with the concept of LHR engine. In the case of LHR engine running on different biodiesel blends, almost all experimental studies has predicted improved performance. This paper analyses and discussed the operating conditions under which the experimental studies are carried out and the factors which affect thermal efficiency and exhaust emissions in LHR engine.     

Combustion and emission characteristics of a direct injection,compression‐ignition engine when operated on Honge oil,HOME and blends of HOME and diesel

This paper reports the results of research conducted to study the fuel properties of Honge oil and blends of its ester and the subsequent testing of these oils in a four‐stroke, single cylinder, water‐cooled, direct injection, compression‐ignition (CI) engine. Experiments were conducted with injection timings of 19, 23 and 27° BTDC at various loads and at a constant rated speed of 1500?rev?min^?1. The performance and emission characteristics of Honge oil and Honge oil methyl ester (HOME) blended with diesel, to produce blends designated B20, B40 and B80, were studied. The heat release rates, maximum rate of pressure rise, ignition delay, and combustion duration for these fuel combinations were determined.     

Life improvement programme of producer gas–biodiesel operated dual fuel engines

Biomass fuels have attracted an increase in interest due to the alarming rise in global greenhouse gases and the rapid rise of petroleum prices. Energy security on a sustainable basis can come only with the responsible use of home-sourced resources and not from imported fossil fuels such as coal or crude petroleum products. Partial combustion of biomass in the downdraft gasifier generates producer gas that can be used as the sole fuel or as a supplementary fuel for internal combustion engines. A dual fuel mode of operation, in which producer gas is used as a supplementary inducted fuel along with injected pilot fuels of Honge or Jatropha biodiesels, can be a promising alternative to diesel only usage. Two different carburettors were designed and fabricated to facilitate gas entry at 45° and 90° to the engine cylinder. The engine was experimentally optimised using Honge or Jatropha biodiesels–producer gas combinations with respect to maximum pilot fuel savings in the dual fuel mode operation, optimum air and gas mixing with different tested carburettors. The performance, combustion and emission characteristics of these dual fuel combinations were compared at different load conditions. The results showed that biodiesels of Honge or Jatropha oils–Producer gas combinations with carburettor of 90° gas entry resulted in better performance.     

Experimental investigation of diesel engine using EGR and fuelled with Karanja oil methyl ester

Karanja oil methyl ester (KOME), a biodiesel prepared from Karanja oil, a potential source of non-edible oil in India and a prospective alternative to the diesel fuel, shows comparable performance and considerable reduction in emissions except NO_x. Exhaust gas recirculation (EGR) is a popular method of reducing the NO_x emission. The aim of this experimental work was to study the potential of the cooled EGR in a direct injection compression ignition engine operating with the KOME and its blend. The study was conducted with the different EGR rates. Performance and emission parameters were compared by using diesel, KOME and its blend employing EGR and with the same fuels without EGR. The study also differentiates the effect of EGR on KOME and its blend with the neat diesel. The effect of EGR was found to be slightly higher for KOME biodiesel and its blend than for neat diesel. Increased NO_x emission using KOME biodiesel was also found to be reduced by using EGR.     

Fuel efficiency improvement of a dual-fuel engine fuelled with Honge oil methyl ester (HOME)–bioethanol and producer gas

Renewable and alternative fuels have numerous advantages compared with fossil fuels as they are renewable and biodegradable and provide food and energy security and foreign exchange savings besides addressing environmental concerns and socio-economic issues (Yaliwal et al. 2013. International Journal of Sustainable Engineering, doi:10.1080/19397038.2013.801530. Zhu et al. 2011a, Applied Thermal Engineering 31 (14–15): 2271–2278; Zhu et al. 2011b, Fuel 90: 1743-1750; Banapurmath, Tewari, and Hosmath 2008, Renewable Energy 33: 2007-2018; Banapurmath 2009, “Performance, Combustion and Emission Characteristics of a Single Cylinder Direct Injection CI Engine Operated on Dual Fuel Mode Using Honge Oil and Producer Gas.” PhD thesis, 1–195; Banapurmath et al. 2011, Waste and Biomass Valorization 2: 1–11). In this context, the main objective of the present work is to study methods of biofuel production such as Honge oil methyl ester (HOME) using a conventional transesterification process and bioethanol from the Calliandra calothyrsus shrub using a new pretreatment method known as hydrothermal explosion. Further, experimental investigations were carried out on a single-cylinder, four-stroke, direct-injection stationary diesel engine operating in a dual-fuel mode using HOME, bioethanol and producer gas combinations to determine its performance, combustion and emission characteristics. The performance of the dual-fuel engine was analyzed at optimized engine conditions. HOME-Bioethanol (BE) blends such as HOME+ 5% bioethanol (BE5), HOME+ 10% bioethanol (BE10) and HOME+ 15% bioethanol (BE15) were prepared by adding bioethanol to HOME (on volume basis) in different proportions ranging from 5 to 15% with an increment of 5%. In this present work, the effect of different BE blends on the performance of producer gas fuelled dual fuel engine was studied. Experimental investigation on dual fuel engine using BE5-Producer gas operation resulted in up to 4–9% increased brake thermal efficiency with decreased hydrocarbon (HC), carbon monoxide (CO) and marginally increased nitric oxide (NOx) emission levels compared to HOME-Producer gas, BE10-producer gas and BE15-producer gas mode of operation. However, it was observed that, the overall performance of BE-producer gas operation was found to be lower compared to diesel-producer gas operation.     

Honge oil methyl ester and producer gas-fuelled dual-fuel engine operated with varying compression ratios

Alternative and renewable fuels have numerous advantages compared with fossil fuels as they are renewable and biodegradable, besides providing food and energy security and foreign exchange savings and addressing environmental and socio-economic issues. Therefore, these renewable fuels can be used predominantly in compression ignition (CI) engines for transportation purposes and power generation applications. Today, the use of biomass-derived producer gas is more relevant for addressing rural power generation and is also a promising technique for controlling both NO_x and soot emission levels. Although a producer gas–biodiesel-operated dual-fuel diesel engine exhibits lower performance, they are independent from the use of fossil fuels. The lower performance of the engine could be due to the slow-burning and lower calorific value of producer gas. For this purpose, exhaustive experiments on the use of Honge oil methyl ester (HOME)–producer gas in a dual-fuel CI engine were carried out for the improvement of its fuel efficiency. This paper presents the effect of the compression ratio (CR) on the performance, combustion and exhaust emission characteristics of a single-cylinder, four-stroke, direct injection stationary diesel engine operated using HOME and producer gas in a dual-fuel mode. The results indicated that the HOME–producer gas combination exhibited lower brake thermal efficiency (BTE) with comparable emission levels with the diesel–producer gas combination at different CRs. Comparative measures of BTE, peak pressure, pressure–crank angle variation, heat release rate, smoke opacity, and hydrocarbon (HC), carbon monoxide (CO) and nitric oxide (NO_x) emission levels are presented and analysed.     

Production of renewable and sustainable fuel from Calliandra calothyrsus and its utilisation in compression ignition engines

Alternative fuels have several advantages compared to fossil fuels as they are renewable, biodegradable, provide energy security, foreign exchange saving as well as help in addressing environmental concerns and socio-economic issues. Therefore, renewable fuels can be used predominantly as a fuel for transportation and for applications in power generation. Shaft power application is a key factor for economic growth and prosperity and depends crucially on the long-term availability of energy from sources that are affordable, accessible and environmentally friendly. In this context, the main objective of the present study was to implement the production of bioethanol from Calliandra calothyrsus, a potential lignocellulosic raw material for the cellulose-to-bioethanol conversion process that can be used as an alternative resource to starch- or sugar-containing feedstock. This study addresses a new pretreatment method known as hydrothermal explosion using C. calothyrsus for ethanol production. The present study also involves experimental investigations on a single-cylinder, four-stroke, direct-injection diesel engine operated with Honge oil methyl ester (biodiesel) and ethanol and its comparison with a neat diesel fuel mode of operation. The results revealed that optimal parameters for bioethanol production from C. calothyrsus were 2% acid concentration (HCl), 100°C temperature and 80 min retention time. For a diesel engine operated with a HOME–bioethanol blend, the experimental results showed a 3–4% decrease in brake thermal efficiency with a 8–10% increase in hydrocarbon and carbon monoxide emission levels and a 15–18% decrease in nitric oxide emission levels when compared with a neat diesel fuel mode of operation.     

Combustion performance and emission characteristics on HCCI engine of waste plastic pyrolysis oil biodiesel blends with external PFI and vaporiser

ABSTRACT

Analysis of plastic oil obtained from waste plastic through pyrolysis process, as an alternative to biodiesel is presented in this paper. The HCCI engine is considered for experimental validation of combustion performance and emission characteristics. To accumulate pyrolysis oil as fuel, the design modifications were made in external mixture formation on the existing computerised 4-stroke, single cylinder, water cooled, direct injection kirloskar diesel engine connected with eddy current dynamometer to satisfy HCCI conditions. HCCI engine can be worked on wide assortment of fuels beginning from diesel to different blends (WPPO 5%,10%,15% and 20% by volume) of biodiesel .The designed additional device connected to the engine is utilised for fuel vaporisation and mixture arrangement. In the experimental study, the combustion results were initiate to be of 39.69 % higher Rate of Heat Release (RoHR) for biodiesel HCCI as compared with diesel HCCI. Higher brake thermal efficiency (BTE) was found 37 % without exhaust gas recirculation (EGR) at WPPO 20 % biodiesel blend. And also found 50 % and 65 % reduction in NOx emission and 18 % and 28 % reduction in smoke opacity are obtained for biodiesel vapour induction without EGR and biodiesel vapour induction with 15 % EGR as compared with diesel fuel. The CO (0.34 %), and UHC (2.15 %) emissions are increases with 15 % EGR, but the emissions are within the standard limits specified by the emissions standards.