改性纤维球处理炼油废水的应用研究

通过用改性纤维球处理炼油废水的试验,对纤维球过滤技术的处理效果和反冲洗特性进行了详细的研究,试验结果表明,炼油废水经处理后,出水中油的含量小于4 mg/L、悬浮物含量小于6 mg/L,出水可达标排放,并且经过改性后的纤维球在含油废水处理中可以通过反冲洗再生并重复使用.     

UBAF与纤维球过滤结合工艺应用于污水回用的试验研究

利用升流式曝气生物滤池 (UBAF)与纤维球过滤相结合的工艺对城市污水进行深度处理 ,使其达到回用的要求。结果表明 :对于经过二级处理后的可生物降解性较差的城市污水 ,应用UBAF和纤维球过滤相结合的处理工艺能够取得很好的效果 ,处理后的污水完全可以达到污水排放的一级标准和城市生活杂用水的标准     

固相萃取-GC/MS法测定地表水中3-甲基吲哚

采用微球硅胶键合C_(18)固相萃取柱萃取水样中的3-甲基吲哚,并用气质联用法测定,方法在0 mg/L~10.0 mg/L范围内线性良好,方法检出限为0.2μg/L。空白水样3个质量浓度水平的加标回收率为89%~94%,7次测定结果的RSD为2.3%~6.9%。用该方法测定7个实际地表水样品,其中4个地表水样品检出3-甲基吲哚,地表水样的加标回收率为81.5%~97.0%。     

A metal-free composite photocatalyst of graphene quantum dots deposited on red phosphorus

A simple approach to enhance the photocatalytic activity of red phosphorus(P) was developed.A mechanical ball milling method was applied to reduce the size of red P and to deposit graphene quantum dots onto red P. The product was characterized by scanning electron microscopy, transmission electron microscopy, contact angle measurements, zeta-potential measurements, X-ray diffraction and UV–vis absorption spectroscopy. The product exhibited high visible-light-driven photocatalytic performance in the photodegradation of rhodamine B.     

An experimental investigation into micro ball end-milling of silicon

Silicon is a representative operational material for semiconductor and micro-electronics. In certain MEMS applications, it is required to fabricate three dimensional channels and complex pattern on silicon substrate. Such features are typically fabricated by photolithography and chemical etching. These processes have low productivity and have certain other limitations. Therefore, a viable switch-over from non-traditional fabrication processes to traditional machining is highly desired for improved productivity in high-mix low-volume production. However, machining of silicon by traditional process is extremely difficult due to its high brittleness. Even very small forces produced during machining can cause brittle fracture on silicon surface resulting in deteriorated surface quality. The fundamental principle in machining of a brittle material such as silicon is to achieve material removal through plastic deformation rather than crack propagation. This paper presents the experimental results of ductile-mode machining of silicon by micro ball end-milling. The workpiece surface was inclined to the rotational axes of the cutter to improve the surface finish. It was established experimentally that 15-μm deep, fracture-free slots can be machined on silicon wafer by micro ball end-milling if the feed rate is below a certain threshold. The influence of several machining parameters on the roughness of machined-surface was also investigated. Cubic boron nitride (CBN) is presented as much economical alternative tool-material to single-crystal diamond for machining silicon in ductile-mode.     

深水水下测试树球阀剪切连续油管性能分析

为研究不同工况、不同结构参数对于深水水下测试树球阀剪切连续油管性能的影响,采用有限元分析软件建立剪切分析模型,对不同工况下剪切过程进行数值模拟,并与试验对比验证分析模型的准确性;结果显示,有限元模型结果与试验结果相对偏差小于5%;油管剪切过程中会出现2个剪切力矩峰值,通过分析不同工况下2个峰值变化规律,发现油管承受拉力越大、球阀剪切速度越小、球阀外径越小剪切过程所需剪切力越小,剪切性能越好。研究结果表明:得到的剪切模型及不同工况下剪切力变化规律,可为水下测试树的设计选型及现场应用提供指导及参考意义。     

多孔球三相流化床冷态试验的研究

对多孔球为填料的三相流化床进行冷态试验研究,研究不同工况下气体空塔流速、填料静止高度、喷淋密度等因素对流化床阻力特性和脱硫效率的影响.试验表明,用多孔球替代空心球做填料,不仅可以消除空心球在流化过程中出现的问题,还可以适当提高脱硫效率.     

大半径浅圆弧的切削加工及误差分析

在机械加工中采用近似法加工空间曲面,常常使加工过程变得简单可行,而且解决了部分机床力不能及的矛盾.在此介绍了在普通铣床上用椭圆曲线网络加工大半径浅圆弧的加工原理、加工方法及其误差分析.     

High-energy milling to decontaminate soils polluted by polychlorobiphenyls and atrazine

Mechanical energy has been used so far for running chemical reactions and for preparing new materials in absence of solvents. Very recently, the technology has been applied to solve environmental problems. In this paper, we describe the application of high-energy milling (HEM) for the remediation of soils contaminated by chlorinated organic compounds such as polychlorobiphenyls (PCBs) and agrochemicals like atrazine. NaBH₄ and LiAlH₄ have been successfully used for the total dehydrohalogenation of both classes of compounds, leaving a residue lower than 2 ppmw of the starting compound in the treated soil. LiAlH₄ was found to be more active than NaBH₄.     

MB1870型球磨机噪声治理

球磨机运转时噪声很大,不仅生产操作时工人难以承受,而且对周围居民的生活环境造成严重污染.我们采用约束型粘弹阻尼结构减震,并结合吸声、隔声和消声技术进行综合治理,取得了良好的降噪效果.