湿法吸收测定大气中的五氧化二磷

用２％ＮａＯＨ溶液吸收大气中的Ｐ２Ｏ５，用钼锑抗试剂显色定量。对样品的稳定性、方法的显色条件、精密度、准确度以及检出限进行反复试验，结果令人满意。     

极性基湿润剂与矿岩类粉尘颗粒的作用机理

根据矿岩类粉尘微颗粒的表面性质和极性基湿润剂的特性，应用分子热力学和表面物理化学理论探讨了湿润型抑尘剂与矿岩类粉尘之间的相互作用机理。矿岩类粉尘吸附水的本质是由于它们之间的相互吸引作用，是分子之间的短程相互作用力和长程作用力共同作用的结果。当矿岩类粉尘与水相碰撞时，只有当吸引力大于排斥力时，水分子才能牯附于矿岩类粉尘，表面张力和体系自由能足够小时，水才能湿润矿岩类粉尘。分析了湿润剂对水和矿岩类粉尘的表面改性的原理，它增加水和矿岩类粉尘之间的相互作用力，减小了界面表面张力和体系自由能，使矿岩粉尘被水湿润能自由地进行。     

Injury risk functions for frontal oblique collisions

Objective: The objective of this article was the construction of injury risk functions (IRFs) for front row occupants in oblique frontal crashes and a comparison to IRF of nonoblique frontal crashes from the same data set.

Method: Crashes of modern vehicles from GIDAS (German In-Depth Accident Study) were used as the basis for the construction of a logistic injury risk model. Static deformation, measured via displaced voxels on the postcrash vehicles, was used to calculate the energy dissipated in the crash. This measure of accident severity was termed objective equivalent speed (oEES) because it does not depend on the accident reconstruction and thus eliminates reconstruction biases like impact direction and vehicle model year. Imputation from property damage cases was used to describe underrepresented low-severity crashes―a known shortcoming of GIDAS. Binary logistic regression was used to relate the stimuli (oEES) to the binary outcome variable (injured or not injured).

Results: IRFs for the oblique frontal impact and nonoblique frontal impact were computed for the Maximum Abbreviated Injury Scale (MAIS) 2+ and 3+ levels for adults (18–64 years). For a given stimulus, the probability of injury for a belted driver was higher in oblique crashes than in nonoblique frontal crashes. For the 25% injury risk at MAIS 2+ level, the corresponding stimulus for oblique crashes was 40 km/h but it was 64 km/h for nonoblique frontal crashes.

Conclusions: The risk of obtaining MAIS 2+ injuries is significantly higher in oblique crashes than in nonoblique crashes. In the real world, most MAIS 2+ injuries occur in an oEES range from 30 to 60 km/h.     

Non-UV based germicidal activity of metal-doped TiO2 coating on solid surfaces

A stain-based screening method was developed to screen different catalyst coatings for their germicidal activity. A Baclight dead/live bacteria viability kit （invitrogen, molecular probes） was used for staining the cell. The screening was carried out following a standard procedure. This included loading cell suspension to solid surface and maintaining contact for 30 min, then staining with a mixture containing dyes. The stained cells were observed using an epifluorescent microscope and photographed with a CCD camera under UV. Metal-doped TiO2 coatings on AI plates were prepared and tested for non-UV germicidal activity without using UV. It was tested using model microorganisms such as Bakers Yeast （Saccharomyces cerevisiae）, Bacillus subtilis, Pseudomonas putida, and Escherichia coli. On the basis of the germicidal activity of catalyst and the degree of damage caused to the cells, the stained cells may appear green （viable）, green with red or yellow nuclei and yellow （compromised） or red （nonviable）. According to their stained color, cells were counted to calculate the percentage of dead, live, and compromised cells. Compromised cells are cells that grow very slowly after reculturing indicating a degree of reversible cell damage. Screening the germicidal activity using this staining method is accurate and efficient, and requires less time than the culture-based method. A modification to the procedure for measuring germicidal activity of rough surfaces or fibrous coatings was developed. Both TiO2 and metal-doped TiO2 （Ag, Pt, Au, Cu） possess non-UV based germicidal activity. The germicidal activity of TiO2 was found to be related with its wetting property and can be improved by UV irradiation before testing. It is not greatly affected by contact time, indicating a fast acting germicidal activity.     

间歇浸取对废物水泥窑共处置产品中Cr和As释放的影响

研究间歇浸取条件下废物水泥窑共处置产品中重金属Cr、As的释放,对水泥产品在实际应用中的环境安全性评价有重要意义.通过模拟煅烧实验制取含Cr和As的水泥熟料,并制取混凝土样品,采用pH影响实验和扩散浸出实验,研究了混凝土中Cr和As的溶解特性及其间歇浸取对混凝土中Cr和As释放的影响.结果表明,浸取方式对浸取液pH有较...     

城市生活垃圾综合处理前分选系统设计

本文以江油市城市生活垃圾处理厂为工程实例,介绍了垃圾前分选系统中的垃圾储料车间、行车与抓斗、垃圾上料机构、双层振动筛以及人工分选平台的工艺设计参数及设计依据,并在此基础上提出了该系统的改进建议.     

A SIMPLE HYDRAULIC SIMULATOR1

ABSTRACT: A simple simulator was constructed, calibrated, programmed and used in management studies of a hydraulic system containing two pumping stations in series, connected by canals and reservoirs. The features of the model, its calibration and use are described, and comparisons between measured and computed hydraulic behavior are presented.     

节水灌溉与控释肥施用对太湖地区稻田土壤氮素渗漏流失的影响

在太湖流域采用田间小区试验研究了干湿交替节水灌溉与控释肥(控释BB肥与树脂包膜尿素)施用对稻田30 cm深土壤渗漏水总氮(TN)、铵态氮(NH+4-N)、硝态氮(NO-3-N)和亚硝态氮(NO-2-N)浓度的动态变化及氮素淋失的影响.结果表明:各处理渗漏水TN、NH+4-N和NO-2-N浓度均在施肥后10 d内达到高峰,然后逐渐下降.渗漏水氮素以NH+4-N(0.22~15.15 mg·L-1)为主,平均占TN 70.1%,NO-3-N(0.10~0.95 mg·L-1)占TN比例较低,平均为13.0%,NO-2-N(0~0.24 mg·L-1)平均仅占TN 1.3%.与淹灌相比,节灌对稻田渗漏水氮素浓度及各氮素占总氮的比例影响不大,但降低了14.2%的渗漏水量和9.4%的TN淋失量.施氮显著提高了渗漏水氮素浓度以及NH+4-N和NO-2-N占TN的比例.控释BB肥和树脂包膜尿素较常规尿素处理水稻全生育期渗漏水TN平均浓度分别降低10.2%和43.3%,TN淋失量分别降低26.1%和39.5%.综上,干湿交替节灌结合树脂包膜尿素施用有利于降低氮素渗漏损失,促进农田面源污染减排.     

添加剂对炭黑颗粒润湿和沉降性能的影响

为提高湿式除尘装置对炭黑颗粒物的去除效率，通过向吸收液中添加复配表面活性剂以提高吸收液对炭黑的润湿性，投加絮凝剂使进入吸收液的炭黑颗粒发生凝聚和沉降，从而使吸收液得以循环利用。其中表面活性剂的复配以非离子表面活性剂月桂醇聚氧乙烯（9）醚（AEO-9）为主，与十二烷基苯磺酸钠（SDBS）、十六烷基三甲基溴化胺（CTAB）和壬酚基聚氧乙烯醚（TX-10）分别复配，筛选出复配效果最好的一组复配液；然后投加絮凝剂，探讨絮凝剂的加入对吸收液中炭黑颗粒物絮凝沉降的影响。结果表明，在AEO-9浓度为0．05mmol／L，TX-10浓度为0．09mmol／L时，吸收液的表面张力最小，为36．75mN／m；投加无机絮凝剂聚合氯化铝（PAC）浓度为100mg／L时，经15min沉降，炭黑的沉降率可达88．1％，上清液中悬浮颗粒的平均粒径为6．36μm。     

Prediction of minimum ignition energy of aerosols using flame kernel modeling combined with flame front propagation theory

Flammable aerosols have created many fire and explosion hazards in the process industry, but the flammability of aerosols has not been fully understood. The minimum ignition energy has been widely used as an indicator for flammability of combustible mixtures, but the amount of experimental data on the minimum ignition energy of aerosols is very limited. In this work, the minimum ignition energy of tetralin aerosols is predicted using an integrated model. The model applies the flame front propagation theory in aerosol systems to the growth of the flame kernel, which was created during the spark discharge in the ignition process. The aerosol minimum ignition energy was defined as the minimum level of energy in the initial flame kernel to maintain the kernel temperature above the minimum ignition temperature of 1073 K specific for tetralin aerosols during the kernel growth. The minimum ignition energy obtained in the model is influenced by the fuel-air equivalence ratio and the size of the aerosol droplets. For tetralin aerosols of 40 μm diameter, E_min decreases significantly from 0.32 mJ to 4.3 × 10 e⁻³ mJ when the equivalence ratio rises from 0.57 to 1.0. For tetralin aerosols of 0.57 equivalence ratio, E_min increases from as 0.09 mJ to 0.32 mJ when the droplet diameter rises from 10 μm to 60 μm. The trends are in agreement with previous experimental observations. The method used in current work has the potential to prediction of the minimum ignition energy of aerosol.