铁铜双金属有机骨架MIL-101(Fe,Cu)活化双氧水降解染料性能

针对非均相芬顿传质效率低和Fe（Ⅲ）Fe（Ⅱ）转化慢导致活性低等问题,采用溶剂热法制备铁铜双金属有机骨架材料[MIL-101（Fe,Cu）],并研究了材料界面性质、催化降解染料（亚甲基蓝）性能以及活化催化机制.结果表明,MIL-101（Fe,Cu）晶体结构完整且呈三维八面体形状;比表面积和平均孔径分别为667.2 m² ·g^-1和1.9 nm,可充分暴露反应活性位点.MIL-101（Fe,Cu）在广谱pH范围可活化H₂ O₂高效降解亚甲基蓝.当pH=5、反应20 min,MIL-101（Fe,Cu）/H₂ O₂对20 mg ·L^-1亚甲基蓝的去除率为100%,较MIL-101（Fe）/H₂O₂和单独H₂ O₂分别提高43.1%和88.9%.自由基猝灭实验与反应前后铁和铜价态变化结果表明,羟基自由基（·OH）是MIL-101（Fe,Cu）/H₂ O₂催化降解亚甲基蓝的主要活性物种;Cu（Ⅱ）掺杂引入新的活性位点,且Cu（Ⅱ）/Cu（Ⅰ）循环和Fe（Ⅲ）/Fe（Ⅱ）循环可协同产生·OH,进而提高催化效率.MIL-101（Fe,Cu）作为新型非均相类芬顿催化剂,无需复杂pH调节即可获得良好催化效果,在工业废水处理上具有较好地应用前景.     

漓江流域δD和δ18O对蒸发的指示作用

以漓江流域为例查明不同水体之间氢氧稳定同位素组成特征,并探讨氢氧稳定同位素对漓江流域的蒸发过程指示作用.结果表明：流域内不同水体之间,氢氧稳定同位素表现出不同的组成特征,地表水和地下水,在丰水期δD值和δ¹⁸O值要比枯水期更容易富集,地下水的δD值和δ¹⁸O值分布范围较地表水小;随着水温的升高,δ¹⁸O的变化趋势比d-excess明显.从漓江上游到下游高程逐渐下降,河水线的斜率和截距也在逐渐减小,其中漓江下游河水线的斜率和截距要低于当地大气降水线,表明下游受到蒸发作用较强烈;地下河水线、地表河水线在一定程度上偏离当地大气降水线,但偏离程度较小,表明三者之间有很好的水力联系.受温度和湿度的共同影响,漓江干流丰水期河水的蒸发量占最初水体总量的0.7%~9.1%,枯水期河水的蒸发量占最初水体总量的2.6%~9.7%,丰水期的蒸发比例低于枯水期,从上游到下游蒸发比例在逐渐上升.研究区蒸发量估算值为959.40mm,与多年实测值少43.11mm,相对误差4.70%.氢氧稳定同位素对研究区降水、地表水、地下水之间的转换规律具有重要的实际意义,在今后的漓江流域水文研究中有着更加广阔的空间.     

焚烧飞灰重金属含量及浸出长期变化规律研究

通过对24个飞灰样品的重金属全量消解和高精度X射线荧光光谱法（HDXRF）快速检测结果进行线性回归分析,发现HDXRF法可较准确测定飞灰中Cu、Pb、Zn、Ni和Cd含量（线性回归决定系数R²³0.90）.采用HDXRF法对某焚烧厂飞灰重金属含量6个月快速检测及浸出毒性测定数据统计分析发现：飞灰重金属月均含量较稳定（变异系数CV<0.14）但日均含量波动较大（CV>2.54）;飞灰中Pb、Cu和Zn含量呈正相关（相关系数r>0.78）;金属浸出浓度受浸出液终点pH值影响显著,超标频率依次为Pb（68.9%）、Cd（66.1%）、Ni（24.0%）、Cu（14.2%）和Zn（1.6%）.短期飞灰金属含量和浸出毒性数据受焚烧工况,烟气处理工况和垃圾组分等多种因素共同影响,不具有代表性.为评估垃圾分类源头削减重金属效果,建议采用快速检测方法对焚烧飞灰重金属含量进行长期监测.     

黄土高原人工刺槐林土壤团聚体中不同活性有机碳从南到北的变化特征

不同粒径团聚体中的不同活性有机碳对人工林土壤质量改善及碳库动态平衡有重要的作用.本研究在黄土高原地区,从南向北沿着降雨和温度降低梯度选择淳化、安塞、绥德和神木共4个地区,比较研究了人工刺槐林土壤团聚体不同的活性有机碳含量变化及其影响因素.通过湿筛法将土壤团聚体分级为粉黏粒（<0.053 mm）、微团聚体（0.25~0.053 mm）和大团聚体（>0.25 mm）,用Leffory法测定3种粒径土壤团聚体低、中、高活性有机碳含量.结果表明：①4个样区大团聚体（>0.25 mm）含量由南至北呈先降低后增加趋势,微团聚体（0.25~0.053 mm）含量逐渐增加,粉黏粒（<0.053 mm）含量则先增后减.②4个样区中土壤团聚体3种活性有机碳含量大小顺序为低活性 > 中活性 > 高活性,其中,粉黏粒（<0.053 mm）低活性有机碳含量为1.02~1.52 g·kg^-1,中活性有机碳含量为0.53~0.91 g·kg^-1,高活性有机碳含量为0.28~0.43 g·kg^-1;而微团聚体（0.25~0.053 mm）低活性有机碳含量为1.02~2.02 g·kg^-1,中活性有机碳含量为0.46~1.20 g·kg^-1,高活性有机碳含量为0.31~0.85 g·kg^-1;大团聚体（>0.25 mm）低活性有机碳含量为1.08~3.07 g·kg^-1,中活性有机碳含量为0.70~1.96 g·kg^-1,高活性有机碳含量为0.48~1.24 g·kg^-1.③黄土高原人工刺槐林3种粒径团聚体的低、中、高活性有机碳含量主要与年均气温（MAT）、年均降雨量（MAP）、土壤SOC、TN和含水率显著相关（p<0.05）,且在同一活性下,活性有机碳含量与MAT、MAP、土壤TN、SOC、含水率的相关性随着土壤团聚体粒径的增大而越显著.研究结果对理解黄土高原土壤团聚体活性有机碳含量在空间尺度上的变化特征和影响因素具有重要意义.     

基于Stacking的地面PM2.5浓度估算

为了解决地面PM_2.5监测网络在空间和时间覆盖受限的问题,提出了基于宽时空覆盖的卫星气溶胶光学厚度AOD,利用Stacking方法建立地面PM_2.5浓度估算模型,将AOD、PM_2.5和各气象参数以及与PM_2.5排放有关的数据进行训练,使用改进网格搜索对模型超参数进行优化,通过对多重共线性分析,建立基于Stacking的最优PM_2.5浓度估算模型。选取2016-01-01-2016-12-31的数据作为实验对象,结果表明:相比于随机森林、GBRT和XGBoost 3种模型,使用岭回归作为元学习器的Stacking模型性能更优,可见Stacking适用于大范围地理区域的大气污染监测。     

雨水管道沉积物中典型无机氮的干期粒径分布

以南京江北新区分流制雨水管道沉积物为研究对象,考察不同粒径沉积物中铵态氮（NH₃-N）和硝态氮（NO₃^--N）干期分布特征,分析其随干期长度的变化关系,并探讨沉积物理化性质及微生物菌群结构对NH₃-N和NO₃^--N干期分布的影响.结果表明：粒径≤0.075mm的沉积物中NH₃-N占比最高（交通区30.8%,商业区36.7%）;交通区粒径≤0.075mm的沉积物中NO₃^--N占比最高（33.0%）,而商业区粒径0.075~0.15mm沉积物中NO₃^--N占比最高（34.4%）;干期长度与交通区0.075~0.15mm粒径段的沉积物中NO₃^--N含量及商业区粒径≥0.3mm的沉积物中NH₃-N含量之间的相关性均最显著;雨水管道沉积物中NH₃-N和NO₃^--N的干期分布与O-H和N-H等官能团、表面极性和亲水性、微观形貌等有一定关联;交通区雨水管道沉积物中Gemmobacter等反硝化优势菌种（相对丰度总和为20.15%）对NO₃^--N干期分布影响更显著.     

Acceleration of floc-water separation and floc reduction with magnetic nanoparticles during demulsification of complex waste cutting emulsions

Waste cutting emulsions are difficult to treat efficiently owing to their complex composition and stable emulsified structure. As an important treatment method for emulsions, chemical demulsification is faced with challenges such as low flocs–water separation rates and high sludge production. Hence, in this study, Fe₃O₄ magnetic nanoparticles (MNPs) were used to enhance chemical demulsification performance for treating waste cutting emulsions under a magnetic field. The addition of MNPs significantly decreased the time required to attain sludge–water separation and sludge compression equilibrium, from 210 to 20 min. In addition, the volume percentage of sludge produced at the equilibrium state was reduced from 45% to 10%. This excellent flocculation–separation performance was stable over a pH range of 3–11. The magnetization of the flocculants and oil droplets to form a flocculant–MNP–oil droplet composite, and the magnetic transfer of the composite were two key processes that enhanced the separation of cutting emulsions. Specifically, the interactions among MNPs, flocculants, and oil droplets were important in the magnetization process, which was controlled by the structures and properties of the three components. Under the magnetic field, the magnetized flocculant–MNP–oil droplet composites were considerably accelerated and separated from water, and the sludge was simultaneously compressed. Thus, this study expands the applicability of magnetic separation techniques in the treatment of complex waste cutting emulsions.     

Investigation to meet China II emission legislation for marine diesel engine with diesel methanol compound combustion technology

In order to reduce the pollutant emission and alleviate the pressure of petroleum resources shortage and greenhouse gas emission at the same time, the use of clean and renewable alternative fuel for marine engines is a promising option. In this study, a marine diesel engine, which was modified to run in diesel methanol compound combustion (DMCC) mode, was investigated. After the diesel injection parameters were calibrated, and combined with a sample after-treatment device DOC (diesel oxidation catalyst), the engine could meet the requirements of China II legislation. The overall MSP (methanol substitute percent) reached 54.1%. The value of each pollutant emission was much lower than that in China II emission legislation, and there was almost no methanol and formaldehyde emissions. When methanol was injected into the inlet manifold, the intake air temperature decreased a lot, as well as the exhaust gas temperature, which were beneficial to increase engine thermal efficiency and improve engine room environment. Compared with the engine running in pure diesel mode, when the engine ran in diesel/methanol dual fuel mode, the combustion phase was advanced, and the combustion duration became shorter. Therefore, the engine thermal efficiency increased, and fuel consumption decreased significantly.     

不同制备温度下污泥生物炭对Cr(Ⅵ)的吸附特性

以城市剩余污泥为原料,于300,400,500,600 ℃温度条件下制备生物炭,通过单因素静态吸附实验探讨制备温度对生物炭吸附Cr（Ⅵ）的影响。结果表明:在500 ℃以内随着温度上升制备的生物炭对Cr（Ⅵ）的吸附量增加,制备温度高于500 ℃后变化不明显;扫描电镜（SEM）、比表面积（BET）、傅里叶红外光谱（FTIR）表征结果显示,热解温度对生物炭表面形貌和官能团组成有显著影响;等温模型及动力学拟合结果表明,生物炭吸附Cr（Ⅵ）为单分子层吸附、物理-化学复合吸附。热解温度对污泥制备生物炭吸附Cr（Ⅵ）的性能有显著影响,最佳制备温度为500 ℃,在此条件制备的生物炭对Cr（Ⅵ）的理论吸附量可达7.93 mg/g。