Investigation to meet China II emission legislation for marine diesel engine with diesel methanol compound combustion technology

In order to reduce the pollutant emission and alleviate the pressure of petroleum resources shortage and greenhouse gas emission at the same time, the use of clean and renewable alternative fuel for marine engines is a promising option. In this study, a marine diesel engine, which was modified to run in diesel methanol compound combustion (DMCC) mode, was investigated. After the diesel injection parameters were calibrated, and combined with a sample after-treatment device DOC (diesel oxidation catalyst), the engine could meet the requirements of China II legislation. The overall MSP (methanol substitute percent) reached 54.1%. The value of each pollutant emission was much lower than that in China II emission legislation, and there was almost no methanol and formaldehyde emissions. When methanol was injected into the inlet manifold, the intake air temperature decreased a lot, as well as the exhaust gas temperature, which were beneficial to increase engine thermal efficiency and improve engine room environment. Compared with the engine running in pure diesel mode, when the engine ran in diesel/methanol dual fuel mode, the combustion phase was advanced, and the combustion duration became shorter. Therefore, the engine thermal efficiency increased, and fuel consumption decreased significantly.     

Photodegradation of Hexafluoropropylene Oxide Trimer Acid under UV Irradiation

As a novel alternative to traditional perfluoroalkyl substances (PFASs), including perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS), hexafluoroproplyene oxide trimer acid (HFPO-TA) has been detected worldwide in surface water. Moreover, recent researches have demonstrated that HFPO-TA has stronger bioaccumulation potential and higher hepatotoxicity than PFOA. To treat these contaminants e.g. PFOA and PFOS, some photochemical techniques by adding exogenous substances had been reported. However, there is still no report for the behavior of HFPO-TA itself under direct UV irradiation. The current study investigated the photo-transformation of HFPO-TA under UV irradiation in aqueous solution. After 72 hr photoreaction, 75% degradation ratio and 25% defluorination ratio were achieved under ambient condition. Reducing active species, i.e., hydrated electrons and active hydrogen atoms, generated from water splitting played dominant roles in degradation of HFPO-TA, which was confirmed by different effects of reaction atmospheres and quenching experiments. A possible degradation pathway was proposed based on the products identification and theoretical calculations. In general, HFPO-TA would be transformed into shorter-chain PFASs, including hexafluoropropylene oxide dimer acid (HFPO-DA), perfluoropropionic acid (PFA) and trifluoroacetate (TFA). This research provides basic information for HFPO-TA photodegradation process and is essential to develop novel remediation techniques for HFPO-TA and other alternatives with similar structures.     

基于TMVOC的地下水位波动带苯系物迁移转化模拟

为探究水位波动情况下苯系物的迁移转化规律,提高石油污染场地地下水污染治理精度,以西北某傍河石化场地为研究对象,基于TMVOC模型对特征污染物苯系物开展泄漏模拟,通过情景模拟比较水位波动对苯系物迁移转化的影响,并从污染分布、相间转化等方面,解析地下水位稳定和波动状态下苯系物迁移转化过程差异.结果表明:①TMVOC模型较好地模拟了水位波动状态下苯系物迁移转化过程.②相较于水位稳定状态下,水位波动作用下苯系物污染深度增加0.5 m,污染面积增加25%,总质量增加12 kg.③水位稳定和波动状态下苯系物"气-液-NAPL（Non-Aqueous Phase Liquids）相"占比分别为0.17%、2.03%、97.8%和0.04%、3.69%、96.27%.④NAPL相苯系物饱和度分布与苯系物质量分布呈正相关,水位波动造成NAPL相初始饱和度降低,且初始水位面以下NAPL相饱和度升高.⑤对于苯而言,水位波动状态下非饱和带中苯在液相中的质量是水位稳定状态下的1.11倍,饱和带为10.15倍.研究显示,水位波动显著地影响了苯系物的迁移转化过程,促进了苯系物的溶解,并使更多的苯系物残留在地下介质中.      

环境浓度下邻苯二甲酸二乙酯对秀丽隐杆线虫的生态毒理效应

DEP (diethyl phthalate,邻苯二甲酸二乙酯)是一种在环境中普遍存在的具有潜在神经和生殖毒性的增塑剂,其会干扰环境生物的发育水平、运动行为及生化水平.以秀丽隐杆线虫的体长、体宽、头部摆动频率及生化指标作为测试终点,评估环境中DEP对秀丽隐杆线虫的生态毒理效应.在不同环境浓度(0、0.000 2、0.002、0.02、0.2、2 mg/L)的DEP溶液中,对秀丽隐杆线虫进行不同时间(24 h、72 h和10 d)的暴露试验.结果表明:①在不同浓度DEP溶液中暴露24 h后,秀丽隐杆线虫的发育水平均未受到显著影响(P>0.05).②在不同浓度DEP溶液中暴露72 h后,秀丽隐杆线虫的发育水平受到干扰.与对照组相比,在DEP浓度最高(2 mg/L)时,秀丽隐杆线虫体长下降了3.21%(P < 0.05);在DEP浓度为0.000 2 mg/L时,秀丽隐杆线虫的体宽呈上升趋势,且头部摆动频率明显加快了5.52%(P < 0.01),秀丽隐杆线虫的发育水平受到显著抑制.③在不同浓度DEP溶液中暴露10 d后,与对照组相比,秀丽隐杆线虫的体长、体宽和头摆频率均出现下降;在DEP浓度为2 mg/L时,秀丽隐杆线虫体内活性氧自由基、脂褐素和细胞凋亡水平累积均增长显著,出现氧化应激损伤.研究显示,不同环境浓度的DEP溶液会对秀丽隐杆线虫产生一定的毒性影响,且不同暴露时间和暴露浓度产生的毒性影响也存在一定差异.      

一株高效嗜碱反硝化菌的分离鉴定及其脱氮特性研究

为了应对日趋严苛的废水TN排放标准要求,试验采用溴百里酚蓝（BTB）培养基,从某煤化工废水处理厂反硝化缺氧池活性污泥中,经多次分离、纯化获得了一株高效兼性厌氧反硝化菌株HK13.通过形态观察及16S rRNA基因序列分析,菌株HK13被鉴定为施氏假单胞菌属（Pseudomonas stutzeri）.在此基础上,利用含硝酸盐模拟废水,探讨了碳源类型、C/N（碳氮比）、初始pH、溶解氧（以不同摇床转速表征不同浓度的溶解氧）和培养温度对菌株HK13反硝化脱氮能力的影响,确定了该菌株的最优生长条件和最大脱氮效率.结果表明:①菌株HK13最适反硝化脱氮条件为以柠檬酸钠碳源,C/N 8,培养温度35℃,初始pH 8~10,摇床转速100 r/min.②初始ρ（NO₃--N）为106.67 mg/L下,反应12 h后菌株HK13对TN的去除率可达92.62%;反应9~12 h时,该菌株的脱氮速率最高,可达20.03 mg/（L·h）,其16 h的脱氮率在98%以上,且无亚硝酸盐积累.③菌株HK13适宜生长的温度和pH范围广泛,分别为20~40℃和7~10.研究显示,菌株HK13具有快速高效的脱氮能力及嗜碱特性,拓宽了生物脱氮工艺对环境条件的适用范围,在废水脱氮领域具有广泛的应用前景.      

三维电极电Fenton法对苯酚废水处理效果实验研究

采用三维电极电Fenton法对制陶工艺含酚废水进行处理,选择pH、时间、电压、FeSO₄·7H₂O投放量、通气量、电解质投放量以及电极间距为单因素,设置不同水平,研究苯酚和COD的去除效果,同时探讨了该方法的电化学能耗。结果表明:在pH为3,电压为15 V,FeSO₄·7H₂O投放量为1.8 g/L,通气量为9 L/min,Na₂SO₄粉末投加量为1.0 g/L,电极间距取10 cm,反应120 min的条件下,废水中苯酚及COD去除率可分别达到94.13%和86.67%,处理效果明显,且能耗较二维电极大大减少,可为该方法在含酚废水处理领域的应用提供参考。     

北京市典型汽修企业VOCs排放特征与臭氧影响分析

对北京地区27家汽修企业进行调研,选取2家典型汽修企业进行气袋采样-GC-MS-FID采集及分析,定量分析其VOCs的排放特征,并计算其臭氧生成潜势（OFP）。结果表明:使用不同漆料的汽修企业排放特征不同,水性漆企业非甲烷总烃的排放浓度为0.62~36.49 mg/m3,油性漆企业的排放浓度为0~100.39 mg/m3;水性漆排放的VOCs以烷烃为主,占比高达57.16%,丙烷（39.65%）和甲苯（11.41%）是首要污染物;卤代烃（55.51%）是油性漆企业的主要VOCs排放物种,主要组分为1,2-二氯丙烷和1,2-二氯乙烷;水性漆企业的OFP值为144.78 mg/m3,油性漆企业的OFP值为664.43 mg/m3,大气反应活性最大的物种多为芳香烃,芳香烃对OFP的贡献率分别为52.18%和88.44%。     

Concentrations and chemical compositions of PM10 during hazy and non-hazy days in Beijing

In order to study the concentrations of major components,characteristics and comparison in hazy and non-hazy days of PM_(10) in Beijing,aerosol samples were collected at urban site in Beijing from December 29,2014 to January 22,2015.Heavy metals like Zn,Pb,Mn,Cu,As,V,Cr and Cd were deeply studied considering their toxic effects on human being;nine water-soluble inorganic ions(SO_4~(2-),NO_3~-,NH_4~+,Na~+,K~+,Cl~-,Ca~(2+) and Mg~(2+)) and carbon fractions(OC and EC) were also analyzed.The concentrations of heavy metals were 1.03–1.98 times higher in hazy days than those in non-hazy days,mainly due to biomass burning and coal burning.The trends in total heavy metals concentrations were basically consistent with the trends in PM concentrations except for two obvious periods(12.29–12.30;1.14–1.15);but when air masses accumulated locally or around Beijing,trends in PM concentrations and heavy metals were opposite.The proportion for NO_3~-/SO_4~(2-) indicated that mobile sources such as automobiles were important reasons for haze in Beijing.Correlation between OC and EC during non-hazy days was strong(R~2= 0.95) but it was low(R~2= 0.67) during hazy days,and large variations for OC/EC values occurred in hazy days.The calculated mass concentration of SOC is 2.58 μg/m~3,which only accounted for 10.1% of the OC concentration.When air masses from the far north-west,they decreased PM concentration in Beijing and they were relatively clean;however,those from the near east,south-east and south of the mainland increased PM concentration and they were dirty.     

有机垃圾厌氧消化泡沫产生机理及控制方法

为了分析厌氧消化泡沫的产生机理和控制方法有助于解决有机垃圾厌氧消化起泡问题,本文调研了近年来报道的厌氧消化系统起泡现象,并从底物特性、反应器构造及运行条件和消化过程相关特性3方面分析了不同底物、工艺和环境条件下厌氧消化反应器的起泡机理;讨论了丝状菌指数、表面张力、粘度、有机负荷、起泡趋势和泡沫稳定性等参数作为起泡风险评价指标的合理性;介绍和比较了4类消泡方法（物理法、机械法、生物法和化学法）的消泡原理及优缺点.目前,除污泥厌氧消化系统外,其他有机垃圾厌氧消化系统起泡的主要因素尚不明确,而这也限制了泡沫控制方法的开发.后期探索关键起泡微生物或研究生物表面活性物质与起泡的相关性,将有助于从新的角度揭示起泡机理,并开发出针对性更强的泡沫控制方法.     

CeO2形貌结构对催化湿式空气氧化苯酚性能的影响

采用水热法、沉淀法和溶胶凝胶法制备了3种不同形貌的CeO₂催化材料,并将其用于湿式空气氧化苯酚水溶液过程中,探讨了CeO₂形貌结构对催化湿式氧化苯酚水溶液性能的影响.采用扫描电子显微镜（SEM）、透射电子显微镜（TEM）、X射线衍射（XRD）、程序升温还原（TPR）等手段对CeO₂催化材料进行了表征.结果表明,水热法制备的CeO₂催化材料表现出较好催化性能,主要原因是水热法合成的CeO₂呈现交错的纳米棒状结构,主要暴露（220）晶面,且沿着（220）晶向生长.在反应温度为200℃、空气压力为2MPa、苯酚初始浓度500mg/L的条件下,最终（240min）COD的去除率为95.5%.