Cloud point extraction–atomic absorption spectrometry for pre-concentration and determination of cadmium in cigarette samples

A new complexing agent, 2-((2-((1H-benzo[d]imidazole-2yl)methoxy)phenoxy)methyl)-1H-benzo[d]imidazole (BIMPI), was used in cloud point extraction and applied for selective pre-concentration of trace amounts of cadmium in cigarette samples. Cadmium was complexed with BIMPI in a buffer solution (pH?=?10) using Triton X-114 as surfactant and quantitatively extracted into a small volume of the surfactant-rich phase after centrifugation. Under optimized conditions (pH?=?10.0, 0.8?×?10^?4?mol?L^?1 BIMPI and 0.08 % (w/v) Triton X-114), calibration graph was linear in the range of 34.0–1,670.0 μg?L^?1. The proposed method was applied to the determination of Cd in various cigarette (tobacco) samples which gave satisfactory results.     

Effect of the water–oil ratio on brine/surfactant/alcohol/oil systems optimized for soil remediation

The optimum middle-phase microemulsion used for remediation of oily contaminated soils is often obtained by mixing a certain amount of a surfactant/alcohol mixture with oil and adjusting the salinity concentrations at a constant water–oil ratio. Upon introduction to the subsurface, however, the system may not be in the optimum state throughout the remediation process owing to the change in the water–oil ratio. This research has attempted to investigate the effect of the water–oil ratio on the phase behavior of systems containing brine, anionic surfactant, alcohols, and different oils. By systematically changing the water–oil ratio, while keeping the others variables constant, the systems exhibited different phase behavior. The results revealed that the effect of the water–oil ratio on system behavior was significant, and analogous to that of salinity. Increasing the water–oil ratio led the system change from winsor I → winsor III → winsor II. The greater the water–oil ratio the lower the salinity required to produce the middle-phase microemulsion, but the narrower the salinity range of the three-phase region. An empirical correlation has been developed in order to predict the changes in phase behavior with the changes in water–oil ratio. This provides a useful tool for designing optimum formulations suitable for soil remediation. Received: October 5, 1999 / Accepted: March 27, 2000     

Health risk assessment of mercury and arsenic associated with consumption of fish from the Persian Gulf

Concentrations of mercury and arsenic in fish from the Persian Gulf were determined by graphite furnace atomic absorption spectrometry. Concentrations of the metals in muscle samples were 0.049–0.402 μg g^?1 for mercury and 0.168–0.479 μg g^?1 for arsenic, with means of 0.133 and 0.312 μg g^?1, respectively. The maximum daily consumption rate (grams per day) and meal consumption limit (meals per month) was calculated to estimate health risks associated with fish consumption. According to the results, the maximum allowable consumption rate varies between 8–56 and 15–96 g/day base on mercury and arsenic content, respectively. The results of this study indicate that the concentration of mercury and arsenic is well below the maximum permissible levels for mercury (0.5 μg g^?1) and arsenic (6 μg g^?1) according to international standards.     

The effect of size and sex on PCB and PAH concentrations in crab Portunus pelagicus

Polychlorinated biphenyl and polycyclic aromatic hydrocarbon concentrations in the hepatopancreas of blue swimming crab (Portunus pelagicus) from the north Persian Gulf were measured. In addition, the relationships between crab size (carapace width) and polychlorinated biphenyl (PCB) and polycyclic aromatic hydrocarbon (PAH) levels in hepatopancreas were investigated by linear regression analysis. Among the PCBs, congeners 110 and 153 were the most frequent and abundant. The results showed that, except in a few cases, significant relationships between PCB and PAH levels and crab size were positive. Comparison between male and female indicated that the average PCB16, 44, 153, and acenaphthylene, acenaphthene, and anthracene concentrations in hepatopancreas of male crab were found to be significantly higher than those found in the female crab.     

Optimized processing power and trainability of neural network in numerical modeling of Al Matrix nano composites

In this research, an experimental study of reinforcing alumina nano-particles into the aluminum alloy matrix was implemented to verify the accuracy of modeling results obtained by feed forward neural networks. Artificial neural network combined with numerical technique were used to predict the various parameters of mechanical properties such as hardness, tensile and compressive yield stress, UTS and elongation percentage. Much experimentation were taken to discover a suitable number of hidden neurons, avoid detraction from the trainability and enable feed forward neural networks to solve more complex problems. The predictions were found to be consistent with experimental measurements.     

Rapid photodegradation and detection of zolpidem over β-SnWO4 and α-SnWO4 nanoparticles: optimization and mechanism

Environmental Science and Pollution Research - We reported the tin (II) tungstate nanoparticles as the photocatalyst and sensor modifier that were synthesized via chemical precipitation reaction...     

Propagation and extinction of dust flames in narrow channels

This article has investigated the propagation and extinction of aluminum dust cloud flame in a narrow channel. The burned and burning dust particles act as heat sources and the channel walls act as heat sinks. In this method, discrete heat source has been used to analyze dust combustion in a narrow channel. Using the superposition of sources and sinks, the preheat zone temperature is predicted as an indicator of flame propagation or extinction. Dust concentration and channel width are two major parameters which affect the quenching distance and flame propagating speed. Wall temperature affects the heat loss; and by preheating the walls, quenching distance is reduced and flame propagation speed is increased.     

Benzene removal by nano magnetic particles under continuous condition from aqueous solutions

Benzene removal evaluated using Fe304 nano continuous condition. A 44 initial benzene concentration, from aqueous solutions was magnetic particles （NM） in factorial design including NM dose, contact time and pH was investigated in 16 experiments （Taguchi OA design）. The results indicated that all factors were significant and the optimum condition was： pH 8, NM dose of 2000 mg.L-1, benzene concentrations of 100 mg.L-1 and contact time of 14min. The maximum benzene uptake and distribution ratio in the optimum situation were 49.4mg.g-1 and 38.4L.g-1, respectively. The nano particles were shown to capture 98.7% of the benzene in optimum batch condition and 94.5% in continuous condition. The isotherm data proved that the Bmnauer-Emmett-Teller model fit more closely and produced an isotherm constant （b） less than one, indicating favorable adsorption. Regeneration studies verified that the benzene adsorbed by the NM could be easily desorbed by temperature, and thereby, NM can be employed repeatedly in water and wastewater management.     

Bioaerosols in the waterpipe cafés: genera,levels, and factors influencing their concentrations

Environmental Science and Pollution Research - This study was conducted in order to assess the exposure to bacterial and fungal bioaerosols in the air of waterpipe cafés (AWPCs), in the hose...