A field study of triclosan loss rates in river water (Cibolo Creek, TX)

Triclosan (TCS) is an anti-microbial agent used in down-the-drain consumer products. Following sewage treatment some of the triclosan will enter receiving waters. This study was designed to determine the die-away rate of triclosan released into a river as part of the sewage treatment plant effluent matrix. The study was conducted in Cibolo Creek, a moderate sized stream (discharge approximately 0.1 m(3)s(-1)) located in South Central Texas. Triclosan was analyzed from samples collected upstream of the sewage treatment plant, the sewage treatment plant effluent, and the river downstream from the effluent discharge. The first-order loss rate of parent triclosan from the water column was calculated from measured data (0.06 h(-1)) and this rate corresponded to a 76% reduction in triclosan over an 8 km river reach below the discharge. Mathematical modeling indicated that sorption and settling accounted for approximately 19% of total triclosan loss over 8 km. When removing sorption and settling, the remaining amount of triclosan had an estimated first-order loss rate of 0.25 h(-1). This loss rate was presumably due to other processes such as biodegradation and photolysis. These data show that loss of parent triclosan from the water column is rapid. Additional data are needed to fully document loss mechanisms.     

Alternative herbicides to manage Italian ryegrass (Lolium multiflorum lam) resistant to glyphosate at different phenological stages

During the growing season of 2002--2003, field and greenhouse experiments were conducted with the objective of evaluating the influence of Italian ryegrass phenological stages and management alternatives on the control of resistant biotypes to glyphosate. Three field experiments were conducted in Lagoa Vermelha, RS, Brazil and glyphosate was applied alone and in combinations with alternative herbicides. Two greenhouse experiments were also conducted at the Department of Crop Science, ESALQ/USP, Piracicaba, SP, Brazil. The Italian ryegrass resistant population was collected from Lagoa Vermelha, RS, Brazil. From the results it was possible to conclude that: (i) the more advanced the phenological stage of application, the more difficult the control of resistant Italian ryegrass by glyphosate, mainly by the rate of 960 g a.i. ha(-1); however, this rate applied at earlier phenological stage (five tillers), the control was higher than 90%; (ii) with the increment of glyphosate rate, it significant response was observed on the control at all stages of application; (iii) the mixture of glyphosate + clethodim (1440 + 72 g a.i. ha(-1)), paraquat + diuron (500 + 250 g a.i. ha(-1)), at all stages of application and clethodim (96 g a.i. ha(-1)) and paraquat + diuron (300 + 150 g a.i. ha(-1)) at the initial stages until pre-flowering were excellent alternatives for management of these populations; and (iv) the response of control was much faster for the mixture of glyphosate + clethodim, independently of growth stage.     

Space-time modeling for the Missouri Turkey Hunting Survey

The Missouri Turkey Hunting Survey (MTHS) is a postseason mail survey conducted by the Missouri Department of Conservation. The 1996 MTHS provides information concerning the number of turkeys harvested by hunters on each day and the total number of trips made to the counties by these hunters on each day of the hunting season. The success rates are then found from this information. Small sample sizes produce large standard errors for the estimates at the county level. We use a Bayesian hierarchical generalized linear model to estimate daily hunting success rates at the county level. The model includes an autoregressive process for the days of the hunting season and spatially correlated random geographic effects. The computations are performed using Gibbs sampling and adaptive rejection sampling techniques. Results show that there are significant spatial corelations between counties and correlations between days of the hunting season. The estimates are close to the frequency estimates at the state level and much more stable at the county level.     

Determination of Cd,Cr, Cu,Pb and Zn from various water samples with use of FAAS techniques after the solid phase extraction on rice bran

A facile and novel method has been developed for the determination of cadmium, chromium, copper, lead, and zinc from various water samples using FAAS. In the present investigation, a syringe was loaded with sorbent (rice bran) for the separation and enrichment of cadmium, chromium, copper, lead, and zinc, prior to their analysis by flame atomic absorption spectrometry which was described to substitute the batch and column techniques. The syringe was loaded with 2.0 g of sorbent in order to retain the analyte elements. Six milliliter of sample solution (pH 8.0 ± 0.2) was drawn into the syringe in 15 s and discharged over a period of 15 s. Then, 2.0 M HCl eluent was drawn into the syringe and ejected back to desorb the analyte elements. At the optimum conditions, the percentage recoveries of Cd, Cr, Cu, Pb, and Zn was in the range of 95.5–99.4% with SD of 0.10%. The elements could be concentrated by drawing and discharging several portions of sample successively. The detailed study of various interferences made the confirmation of the method highly selective. The risk of contamination is less than that with the column technique. The method was successfully applied for the determination of Cd, Cr, Cu, Pb, and Zn in spiked and natural water samples. The results obtained are in good agreement with the reported methods at the 95% confidence level.     

Factors Affecting Resistivity in Electrostatic Precipitation

The following material is taken from a new book, “The Art of Electrostatic Precipitation,” authored by Mr. Katz and based on his 30 years of field experience with the subject. The book provides practical information on maintaining and upgrading precipitators; chapter titles include fundamentals, operation and maintenance, trouble solving, corrosion factors, methods to improve performance, test evaluation techniques, gas distribution and conditioning, case histories, and optimum designs.     

Quantifying methane emission from fugitive sources by combining tracer release and downwind measurements – A sensitivity analysis based on multiple field surveys

Using a dual species methane/acetylene instrument based on cavity ring down spectroscopy (CRDS), the dynamic plume tracer dispersion method for quantifying the emission rate of methane was successfully tested in four measurement campaigns: (1) controlled methane and trace gas release with different trace gas configurations, (2) landfill with unknown emission source locations, (3) landfill with closely located emission sources, and (4) comparing with an Fourier transform infrared spectroscopy (FTIR) instrument using multiple trace gasses for source separation. The new real-time, high precision instrument can measure methane plumes more than 1.2 km away from small sources (about 5 kg h^?1) in urban areas with a measurement frequency allowing plume crossing at normal driving speed. The method can be used for quantification of total methane emissions from diffuse area sources down to 1 kg per hour and can be used to quantify individual sources with the right choice of wind direction and road distance. The placement of the trace gas is important for obtaining correct quantification and uncertainty of up to 36% can be incurred when the trace gas is not co-located with the methane source. Measurements made at greater distances are less sensitive to errors in trace gas placement and model calculations showed an uncertainty of less than 5% in both urban and open-country for placing the trace gas 100 m from the source, when measurements were done more than 3 km away. Using the ratio of the integrated plume concentrations of tracer gas and methane gives the most reliable results for measurements at various distances to the source, compared to the ratio of the highest concentration in the plume, the direct concentration ratio and using a Gaussian plume model. Under suitable weather and road conditions, the CRDS system can quantify the emission from different sources located close to each other using only one kind of trace gas due to the high time resolution, while the FTIR system can measure multiple trace gasses but with a lower time resolution.     

Description and evaluation of a model of deposition velocities for routine estimates of air pollutant dry deposition over North America.: Part I: model development

This paper describes the development of a detailed dry deposition model for routine computation of dry deposition velocities of SO₂, O₃, HNO₃ and fine particle SO₄²⁻ across much of North America. Four different dry deposition/surface exchange sub-models have been combined with the current Canadian weather forecast model (Global Environmental Multiscale model) with a 3 h time resolution and a horizontal spatial resolution of 35 km. The present model uses the US Geological Survey North American Land Cover Characteristics data to obtain fourteen different land use and five seasonal categories. The four sub-models used are a multi-layer model for gaseous species over taller canopy land-use types, a big-leaf model for gaseous species over lower canopies (including bare soil and water) and for HNO₃ under all surface types and, two different models for SO₄²⁻, one for tall canopies and the other for short canopies. All necessary parameters for each sub-model, chemical species, land-use and seasonal categories have been selected from available data libraries or from the values reported in the literature. The purpose for developing this model (referred to as the Routine Deposition Model (RDM)), when coupled with air concentration data, is to provide estimates of seasonal dry deposition, which can be combined with wet deposition to produce total deposition estimates. Model theory is discussed in this paper and model sensitivity tests and results will be presented in a companion paper.