Removal of carotene-like colored compounds by liquid-liquid extraction during polycyclic aromatic hydrocarbons analysis of plant tissue

Plants contain a wide variety of chemicals, some of which may have similar chromatographic behavior to polycyclic aromatic hydrocarbons (PAHs). During solid phase extraction (SPE) with Si-gel for instance, the co-elution of carotene-like colored compounds with PAHs has been observed. In this paper, liquid–liquid extraction was applied for the separation and subsequent analysis of PAHs from plant extracts. PAHs containing 2–6 rings, which include naphthalene, phenanthrene, pyrene, benzo[a]pyrene and benzo[ghi]perylene, were used as representative target chemicals. Carotene-like compounds extracted from Komatsuna (Brassica campestris) shoot by acetone followed by Si-gel treatment were incorporated as undesired components in the model matrix. Results showed the feasibility of employing either acetonitrile or 2% (w/v) KOH–methanol as solvents for high PAHs recovery and low extraction of colored fraction. For acetonitrile, 86.9–93.5% of each PAH could be recovered after three extraction cycles (relative standard deviation, RSD < 1.6%) with only about 10% co-extraction of colored fraction. For 2% KOH–methanol, PAHs recoveries ranging from 79.3% to 83.1% after five cycles (RSD < 1.5%) were achieved while the percent extraction of colored fraction was also low at 10%. The relatively higher selectivity of the solvents for PAHs over the colored fraction as well as the solubility of the matrix solution in the solvent may have contributed to these results. On this basis, liquid–liquid extraction is very useful for the pre-treatment of plant extracts for PAHs analysis.     

Hydrostatic pressure-induced apoptosis on nauplii of Calanus sinicus

The effect of hydrostatic pressure on embryonic development of the calanoid copepod Calanus sinicus was studied. Differences of pressure effect among blastomere stages, 1-cell, 2-cell, 4-cell, 8-cell, 16-cell, blastula and limb-bud stage, were examined under two pressurizing conditions, abruptly (10 atm/min) and gradually (0.1 atm/min) increasing. Egg hatching success, deformity frequency and apoptotic cell degradation of hatched nauplii were examined. Egg hatching success rate was not significantly different between blastomere stages, and also between pressurizing conditions. Deformity frequencies of hatched nauplii were low in the early 1-cell and 2-cell stages, and high in the later blastula and limb-bud stages, in both abrupt and gradual pressurizing conditions. On the other hand, in regard to difference in pressurizing conditions, deformity frequency in gradual pressurizing was significantly higher than that in abrupt pressurizing rate. Gradual pressure increase seems to be more harmful to C. sinicus eggs than abrupt pressure change. Apoptosis induced in nauplii by hydrostatic pressure was detected for the first time in marine zooplankton. The embryos of C. sinicus are sensitive to pressure variations, that is, these embryos are supposed to sink to deeper waters, incurring greater risk of having deformities. In the field, C. sinicus ascend to the surface and spawn at night. By looking from this upward behavior, eggs are spawned at lower pressure and warmer temperature. Probably, the harmless low pressure and warm temperature lead eggs to hatch early and to recruit successfully.     

Influence of aeration modes on leachate characteristic of landfills that adopt the aerobic–anaerobic landfill method

As far as the optimal design, operation, and field application of the Aerobic–Anaerobic Landfill Method (AALM) are concerned, it is very important to understand how aeration modes (different combinations of aeration depth and air injection rate) affect the biodegradation of organic carbon and the transformation of nitrogen in landfill solid waste. Pilot-scale lysimeter experiments were carried out under different aeration modes to obtain detailed information regarding the influence of aeration modes on leachate characteristics. Results from these lysimeter experiments revealed that aeration at the bottom layer was the most effective for decomposition of organic carbon when compared with aeration at the surface or middle layers. Moreover, the air injection rate led to different nitrogen transformation patterns, unlike the lesser influence it has on organic carbon decomposition. Effective simultaneous nitrification and denitrification were observed for the aeration mode with a higher air injection rate (=1.0 L/min). On the other hand, the phenomenon of sequenced nitrification and denitrification could be observed when a low air injection rate (=0.5 L/min.) was employed. Finally, it is concluded that, for AALM, air injection with a higher air injection rate at the deepest layer near the leachate collection pipe tends to accelerate the stabilization of landfill waste as defined in terms of the enhancement of denitrification as well as organic carbon decomposition.     

Atmospheric mercury emissions from waste combustions measured by continuous monitoring devices

Atmospheric mercury emissions have attracted great attention owing to adverse impact of mercury on human health and the ecosystem. Although waste combustion is one of major anthropogenic sources, estimated emission might have large uncertainty due to great heterogeneity of wastes. This study investigated atmospheric emissions of speciated mercury from the combustions of municipal solid wastes (MSW), sewage treatment sludge (STS), STS with waste plastics, industrial waste mixtures (IWM), waste plastics from construction demolition, and woody wastes using continuous monitoring devices. Reactive gaseous mercury was the major form at the inlet side of air pollution control devices in all combustion cases. Its concentration was 2.0–70.6 times larger than elemental mercury concentration. In particular, MSW, STS, and IWM combustions emitted higher concentration of reactive gaseous mercury. Concentrations of both gaseous mercury species varied greatly for all waste combustions excluding woody waste. Variation coefficients of measured data were nearly equal to or more than 1.0. Emission factors of gaseous elemental mercury, reactive gaseous mercury, and total mercury were calculated using continuous monitoring data. Total mercury emission factors are 0.30 g-Hg/Mg for MSW combustion, 0.21 g-Hg/Mg for STS combustion, 0.077 g-Hg/Mg for STS with waste plastics, 0.724 g-Hg/Mg for industrial waste mixtures, 0.028 g-Hg/Mg for waste plastic combustion, and 0.0026 g-Hg/Mg for woody waste combustion. All emission factors evaluated in this study were comparable or lower than other reported data. Emission inventory using old emission factors likely causes an overestimation.

Implications Although waste combustion is one of major anthropogenic sources of atmospheric mercury emission, estimated emission might have large uncertainty due to great heterogeneity of wastes. This study investigated speciated mercury emissions from the combustions of municipal solid wastes, sewage treatment sludge with/without waste plastics, industrial waste mixtures, waste plastics from construction demolition, and woody wastes using continuous monitoring devices. Reactive gaseous mercury was the major form in all combustion cases and its concentration in the gas had large fluctuation. All emission factors evaluated in this study were comparable or lower than other reported data. Emission inventory using old emission factors likely causes an overestimation.     

Expression of foreign genes in primary cultured cells of the blue shrimp Penaeus stylirostris

 The ability to introduce and express foreign genes can greatly facilitate in vitro studies of the molecular biology of an organism. We report here the first use of modified retroviral vectors to achieve foreign gene expression in primary cultured cells from the Oka organ and ovary of the blue shrimp Penaeus stylirostris (Litopenaeus) stylirostris (Holthuis 1980). Of the heterologous promoters tested, the Moloney murine leukemia virus and Rous sarcoma virus promoters mediated the highest levels of reporter gene expression. Firefly luciferase and Escherichia coliβ-galactosidase were successfully used as reporter genes in cultured cells from both Oka organ and ovary. These in vitro systems can be exploited for the study of shrimp cellular biology and regulation of gene expression. Received: 16 January 2000 / Accepted: 21 June 2000     

Three-Dimensional Modeling of an Urban Park and Trees by Combined Airborne and Portable On-Ground Scanning LIDAR Remote Sensing

In this study, we confirmed the utility of airborne and portable on-ground scanning light detection and ranging (LIDARs) for three-dimensional visualization of an urban park and quantification of biophysical variables of trees in the park. The digital canopy height model (DCHM) and digital terrain model generated from airborne scanning LIDAR data provided precise images of the ground surface and individual tree canopies. The heights of 166 coniferous and broadleaf trees of 11 species in the park were estimated from the DCHM images with slight underestimation (mean error = −0.14 m, RMSE = 0.30 m). Portable on-ground scanning LIDAR provided images of individual trees with detailed features. Tree height and trunk diameter were estimated to be within 0.31 m and 1 cm, respectively, from the on-ground LIDAR images. We combined airborne and on-ground LIDAR images to overcome blind regions and created a complete three-dimensional model of three standing trees. The model allowed not only visual assessment from all viewpoints but also quantitative estimation of canopy volume, trunk volume, and canopy cross-sectional area.     

Pyrosequencing Analysis of Norovirus Genogroup II Distribution in Sewage and Oysters: First Detection of GII.17 Kawasaki 2014 in Oysters

Norovirus GII.3, GII.4, and GII.17 were detected using pyrosequencing in sewage and oysters in January and February 2015, in Japan. The strains in sewage and oyster samples were genetically identical or similar, predominant strains belonging to GII.17 Kawasaki 2014 lineage. This is the first report of GII.17 Kawasaki 2014 in oysters.     

Trend analysis of machinery safety for globalization: From the Japanese point of view

In Japan, the work of translation to JIS faced many obstacles. Support groups in Western countries have submitted comments on technical problems. The movement to standard harmonization in safety has rapidly developed in international standardization. The movement for global standardization is developing throughout all the economic areas of the EU. The aim of the Machine Directive that comes into effect in stages is to provide an international formula for a type of qualification in machine safety. EN292 is a nucleus for related standards, which are like a group of planets in a universe. It is a European standard as well as a guideline for implementation, showing practical safety requirements for machines. Horizontal standards, such as EN954 and IEC61508, apply in actual practice.     

Hydrothermal treatment of MSWI bottom ash forming acid-resistant material

To recycle municipal solid waste incinerator (MSWI) bottom ash, synthesis of hydrothermal minerals from bottom ash was performed to stabilize heavy metals. MSWI bottom ash was mixed with SiO(2), Al(OH)(3), and Mg(OH)(2) so its chemical composition was similar to that of hydrothermal clay minerals. These solid specimens were mixed with water at a liquid/solid ratio of 5. The reaction temperature was 200 degrees C, and reactions were performed for 24-240h. Generation of kaolinite/smectite mixed-layer clay mineral was found in the samples after the reaction of the mixture of bottom ash, SiO(2), and Mg(OH)(2). Calcium silicate hydrate minerals such as tobermorite and xonotlite were also generated. X-ray powder diffraction suggested the presence of amorphous materials. Leaching tests at various pHs revealed that the concentration of heavy metals in the leachates from MSWI bottom ash hydrothermally treated with SiO(2) and Mg(OH)(2) was lower than that in leachates from non-treated bottom ash, especially under acid conditions. Hydrothermal treatment with modification of chemical composition may have potential for the recycling of MSWI bottom ash.     

Ozone and/or Water Stresses Could have Influenced the Betula ermanii Cham. Forest Decline Observed at Oku-Nikko, Japan

A serious forest decline of Betula ermanii Cham. has been observed at Mt. Mae-Shirane, Oku-Nikko, Japan, where high ozone (O₃) concentration and severe water deficiency have been measured. In order to consider the possibility whether O₃ and/or water stresses could have been the causes of the forest decline of B. ermanii, plant growth experiments were conducted in environment-controlled growth cabinets. Two-year-old seedlings of B. ermanii were exposed to either charcoal-filtered air (O₃ concentration <5 ppb) or 50 ppb O₃ (daily average, ranging between 20–100 ppb) for 123 days at 20.0/12.5 ± 1.0°C (day/night) and 70/80 ± 7% relative humidity (day/night). Simultaneously, seedlings were treated with three watering regime: 1.0 < pF < 1.8 (no water stress), 1.8 < pF < 2.5 (mild water stress) or 2.5 < pF < 3.0 (severe water stress). O₃ exposure significantly reduced the dry weights of leaf, root and the whole plant, while water stress significantly reduced the dry weights of each organ and the whole plant. Significant reductions of net photosynthesis, transpiration and stomatal conductance were also observed under O₃ and/or water deficiency treatments, while contents of RuBP carboxylase/oxygenase (Rubisco), chlorophyll _a+b and some essential nutrient elements (N, P, K, Mg and Ca) were not markedly changed. It was suggested that the decrease in net photosynthetic rate induced mainly by stomatal closure was the major cause of the growth reduction under O₃ and/or water stresses. No significant interactions between O₃ and water stresses were observed in terms of the depression of dry matter production, which suggested that simultaneous stress treatments of O₃ exposure and water deficiency could affect the tree growth of B. ermanii additively.