Influence of overlap between the laser beam tracks on surface quality in laser polishing of AISI H13 tool steel

Polishing by laser beam radiation is a novel manufacturing process to modify the initial surface topography in order to achieve a desired level of surface finish. The performance of laser polishing (LP) is determined by an optimum combination of several key process parameters. In this regard, the overlap between two successive laser beam tracks is one of the important LP process parameters, which has a significant effect over the final surface quality. In the current study, influence of overlap between the laser beam tracks on surface quality was experimentally investigated during the laser polishing of AISI H13 tool steel. Surface areas were polished by using four different overlap percentages (e.g. 80%, 90%, 95%, and 97.5%) while applying the same energy density. The improvement of surface quality was estimated through the analysis of line profiling surface roughness R_a, areal topography surface roughness S_a, and material ratio function. Also, individual components of the surface quality, e.g. waviness and roughness, and their evolution during LP were statistically analyzed using the power spectral density and the transfer functions. Finally, as an example of the best achieved LP result, flat surface area was polished using optimum set of the process parameters improving surface quality by 86.7% through the reduction of an areal topography surface roughness S_a from 1.35 μm to 0.18 μm.     

Analysis of machined surface quality in a single-pass of ball-end milling on Inconel 718

The ball-end milling process is widely used for generating three-dimensional sculptured surfaces with definite curvature. In such cases, variation of surface properties along the machined surface curvatures is not well understood. Therefore, this paper reports the effect of machining parameters on the quality of surface obtained in a single-pass of a ball-end milling cutter with varying chip cross-sectional area. This situation is analogous to generation of free form cavities, pockets, and round fillets on mould surfaces. The machined surfaces show formation of distinct bands as a function of instantaneous machining parameters along the periphery of cutting tool edge, chip compression and instantaneous shear angle. A distinct variation is also observed in the measured values of surface roughness and micro-hardness in these regions. The maximum surface roughness is observed near the tool tip region on the machined surface. The minimum surface roughness is obtained in the stable cutting zone and it increases towards the periphery of the cutter. Similar segmentation was observed on the deformed chips, which could be correlated with the width of bands on the machined surfaces. The sub-surface quality analysis in terms of micro-hardness helped define machining affected zone (MAZ). The parametric effects on the machining induced shear and residual stresses have also been evaluated.     

Incorporating stakeholder decision support needs into an integrated regional Earth system model

A new modeling effort exploring the opportunities, constraints, and interactions between mitigation and adaptation at regional scale is utilizing stakeholder engagement in an innovative approach to guide model development and demonstration, including uncertainty characterization, to effectively inform regional decision making. This project, the integrated Regional Earth System Model (iRESM), employs structured stakeholder interactions and literature reviews to identify the most relevant adaptation and mitigation alternatives and decision criteria for each regional application of the framework. The information is used to identify important model capabilities and to provide a focus for numerical experiments. This paper presents the stakeholder research results from the first iRESM pilot region. The pilot region includes the Great Lakes Basin in the Midwest portion of the United States as well as other contiguous states. This geographic area (14 states in total) permits cohesive modeling of hydrologic systems while also providing strong gradients in climate, demography, land cover/land use, and energy supply and demand. The results from the stakeholder research indicate that, for this region, iRESM should prioritize addressing adaptation alternatives in the water resources, urban infrastructure, and agriculture sectors, including water conservation, expanded water quality monitoring, altered reservoir releases, lowered water intakes, urban infrastructure upgrades, increased electric power reserves in urban areas, and land use management/crop selection changes. For mitigation in this region, the stakeholder research implies that iRESM should focus on policies affecting the penetration of renewable energy technologies, and the costs and effectiveness of energy efficiency, bioenergy production, wind energy, and carbon capture and sequestration.     

Opportunities to reduce greenhouse gas emissions from households in Nigeria

Efforts to mitigate climate threats should not exclude the household as the household is a major driver of greenhouse gas (GHG) emissions through its consumption patterns. This paper derives an emission index that could be used to estimate inventories of carbon dioxide (CO₂) emissions from kerosene combustion for lighting in Nigeria and also looks at the implications of solar pv lighting replacing kerosene lamp in Nigeria. Findings indicate that (1) average CO₂ emissions from kerosene combustion for lighting in Nigeria is about 0.06 kg per hour per lamp, which can be taken as the kerosene lamp CO₂ emission index for Nigeria. (2) about 3 × 10W_p solar pv will be required to replace a kerosene lamp, while about 0.124 tonnes of CO₂ will be avoided per lamp per year, operating at 6 h daily. At the national level, under the kerosene lamp replacement projection assumptions made, between 0.4 and 1.0 million tonnes of CO₂ will be avoided per year. The household investment required to owe a solar pv, including the capital cost of switching from kerosene lamp, is about US356, while the national capital investment outlay is between 1,138.265 and US356, while the national capital investment outlay is between 1,138.265 and US2,848 million. (3) Certified Emission Reduction (CER) units, assuming CO₂ is traded, will generate significant annual revenues on the order of 6.96 to almost US17.4 million per year, while earnings from unspent household kerosene fuel could amount to between 2,520 and US17.4 million per year, while earnings from unspent household kerosene fuel could amount to between 2,520 and US6,300 million over the life span of the solar pv. The micro-economic assessment carried out indicates the non-attractiveness of solar pv use at the household level, and (4) to promote solar pv use, both long and short term policy measures that aim at cost reduction were suggested. The paper concludes that, factoring the suggested measures into the climate, energy, and financial policy decision discourse in Nigeria could empower the households to play a significant role in achieving global CO₂ emission reduction, but at the local level.     

Prompting safety-belt use in the context of a belt-use law: the flash-for life revisited

PROBLEM: Safety-belt use reduces motor vehicle crash-related morbidity and mortality, yet an estimated 18% of drivers do not consistently buckle up (NHTSA, 2005). In 1985, Geller and colleagues developed an interpersonal Flash-for-Life prompt that increased belt use among 22% of 1,087 unbuckled drivers (Geller, Bruff, & Nimmer, 1985). METHOD: The Flash-for-Life intervention was re-introduced at a large university with high safety-belt use (i.e., 80%). College students stood at parking-lot entrance/exits and "flashed" signs with the message, "Please Buckle Up, I Care" to unbuckled drivers. RESULTS: Of 427 unbuckled drivers observed, 30% of these complied with the prompt. Male drivers were significantly more likely to comply with prompts delivered by females. DISCUSSION: Compliance was higher than in the 1985 study, indicating a high baseline rate of safety-belt use does not negate potential beneficial influence of a prompting intervention. This intervention is particularly effective with college-aged males, a sub-group of the driving population least likely to buckle-up. IMPACT ON INDUSTRY: A simple behavioral prompt could be used at most industrial complexes to increase safety-belt use among vehicle occupants who are not buckled-up.     

The theory of planned behavior as mediator of the effect of parental supervision: a study of intentions to violate driving rules in a representative sample of adolescents

INTRODUCTION: The study reported here was designed to test the ability of the theory of planned behavior to mediate the effect of parental supervision on adolescents' intentions to violate driving rules. METHOD: A representative sample of 1,654 adolescents completed questionnaires during individual and anonymous interviews carried out at their schools. RESULTS: Results showed that age, gender, prior risky driving-behavior, and parental supervision significantly predict intentions to violate driving rules. Attitude and the subjective norm partially mediate the effect of age, prior behavior, and parental supervision. Perceived behavioral control does not predict intention and is not predicted by other variables. IMPACT: The results suggest that social cognitive variables partially mediate the effect of parenting practices such as supervision.     

Time allocation between work and recreation and the associated injury risks among young people

PROBLEM: The purpose of this study was to examine the relationship between overall risk of injury and time use patterns between work and active recreation among adolescents and young adults. METHODS: Using a representative sample of 9,795 Canadians aged 15-24 years, a multivariate logistic regression on the likelihood of any medically attended injury was conducted, including sociodemographic, individual, and time factors. RESULTS: Young people who engaged in a combination of high work and high activity hours were twice as likely to sustain a medically attended injury compared to those who worked low hours, but did not participate in any recreational activity. Those respondents who were not in school had a 43% increase in injury risk compared to full-time students. SUMMARY: Our findings suggest that injury risk was not a simple function of fatigue and cumulative exposure time. Our findings suggest the importance of considering time use and the associated injury risk tradeoffs. IMPACT ON INDUSTRY: Relevant to state and federal work safety policy makers, our findings suggest the importance of understanding where youth might otherwise spend their time if constraint were placed on their employment opportunities, and the associated injury risk tradeoffs must be taken into consideration.     

A juvenile lizard specimen with well-preserved skin impressions from the Upper Jurassic/Lower Cretaceous of Daohugou, Inner Mongolia, China

Lizards are now relatively well known from the Yixian Formation of northeastern China. In this study, we describe a juvenile lizard from a fossil horizon at Daohugou, Inner Mongolia. These beds predate the Yixian Formation, and are probably Late Jurassic or earliest Cretaceous in age. The new specimen thus documents the first lizard material from the Daohugou locality and is the earliest lizard skeleton from China. Comparisons with developmental stages of modern lizards suggest the Daohugou lizard is a hatchling. Although tiny, the specimen is notable in preserving exquisite skin impressions showing the variation in scalation across the body, the shape and position of the cloacal outlet, and details of the manus and pes. These are the earliest recorded lepidosaurian skin traces. In its general proportions and the possession of paired frontals, the small Daohugou lizard resembles both the Yixian taxon Yabeinosaurus tenuis and the questionable Jeholacerta formosa, but it differs from the latter in scalation and, based on other characters, may be distinct from both.     

Rollover injury: effects of near- and far-seating position, belt use, and number of quarter rolls

PURPOSE: Vehicle and occupant responses in rollovers are complex since many factors influence both. This study analyzes the following factors: 1) belt use, 2) seated position with respect to the lead side in the rollover, 3) another front occupant in the crash, and 4) number of quarter rolls. The aim was to improve our understanding of rollover injury mechanisms. METHOD: Rollover accidents were analyzed using 1992-2004 NASS-CDS data. The sample included adult drivers and right-front passengers. All occupants were evaluated and then a subset of non-ejected occupants was analyzed. Using roll direction and seating position, the sample was divided into near- and far-seated occupants. Injury and fatality risks were determined by seatbelt use, occupancy, rollover direction, and number of quarter rolls. Risk was defined as the number of injured (e.g., MAIS 3+) divided by the number of exposed occupants (MAIS 0-6). Significance in differences was determined. A matched-pair analysis was used to determine the risk of serious injury for near- and far-seated occupants who were either belted or unbelted in the same crash. RESULTS: For all occupants, serious injury risks were highest for far-seated, unbelted occupants at 18.1% +/- 4.8%, followed by near-seated unbelted occupants at 12.0% +/- 3.5%. However, the difference was not statistically significant. Belted near- and far-seated occupants had a similar injury risk of 4.3% +/- 1.2% and 4.0% +/- 1.2%, respectively. For non-ejected occupants, serious injury risk was 9.5% +/- 3.2% for far-seated unbelted occupants and 4.9% +/- 2.1% for near-seated unbelted occupants, not a statistically significant difference. Serious injury risk was similar for belted near- and far-seated non-ejected occupants, at 3.6% +/- 1.1%. Seatbelts were 64.2%-77.9% effective in preventing serious injury for all occupants and 62.1%-26.5% for far- and near-seated, non-ejected occupants, respectively. Based on the matched pairs, seatbelts were less effective for near-seated (5.0%) compared to far-seated (2.8%) occupant MAIS 3+F risks. This was similar for non-ejected occupants. An unbelted near-seated occupant increased the risk for a belted far-seated occupant by 2.2 times, whereas an unbelted far-seated occupant increased the risk for a belted near-seated occupant by 10.2 times. For all occupants, the risk of serious injury increased with the number of quarter rolls, irrespective of seated position. For near-seated occupants, seatbelt effectiveness was higher in < or =1 roll than 1+ roll, at 72.3% compared to 28.3%. For far-seated occupants, seatbelt effectiveness was similar in < or =1 and 1+ roll samples at 78.3% and 76.8%, respectively. Near-seated occupants had the lowest serious injury risk when they were the sole occupant in the vehicle. This was also true for non-ejected occupants. However, far-seated occupants had a lower injury risk when another occupant was involved in the crash. CONCLUSIONS: The effect of carrying another occupant appears to reduce the risk of serious injury to far-seated occupants. However, near-seated occupants are better off being the sole occupant in the vehicle. Seatbelt effectiveness was lowest at 28.3% for non-ejected, near-seated occupants in 1+ rolls. This finding deserves further evaluation in an effort to improve seatbelt effectiveness in rollovers. For belted drivers alone in a rollover, fatality risks are 2.24 times higher for the far- versus near-seated position. Analysis of rollovers by quarter turns indicates that occupants are both far-side and near-side in rollovers. The extent to which this confounds the relationship between roll direction, seating position, and injury risk is unknown.     

A new THOR shoulder design: a comparison with volunteers, the Hybrid III, and THOR NT

OBJECTIVE: Since the shoulders are rarely seriously injured in frontal or oblique collisions, they have been given low priority in the development of frontal impact crash test dummies. The shoulder complex geometry and its kinematics are of vital importance for the overall dummy kinematics. The shoulder complex also influences the risk of the safety belt slipping off the shoulder in oblique forward collisions. The first aim of this study was to develop a new 50th percentile male THOR shoulder design, while the second was to compare the new shoulder, mounted on a THOR NT dummy, with volunteer, THOR NT, and Hybrid III range of motion and stiffness data. The third aim was to test the repeatability of the new shoulder during dynamic testing and to see how the design behaves with respect to belt slippage in a 45 degrees far-side collision. METHODS: The new 50th percentile THOR shoulder design was developed with the aid of a shell model of the seated University of Michigan Transportation Research Institute (UMTRI) 50th percentile male with coordinates for joints and bony landmarks (Schneider et al., 1983). The new shoulder design has human-like bony landmarks for the acromion and coracoid processes. The clavicle curvature and length are also made similar to that of a male human, as is the range of motion in the anterior-posterior, superior-inferior, and medial-lateral directions. The new shoulder design was manufactured and tested under the same conditions that T?rnvall et al. (2005b) used to compare the shoulder range of motion for the volunteers, Hybrid III, and THOR Alpha. The new design was also tested in two dynamic test configurations: the first was a 0 degrees full-frontal test and the second was a 45 degrees far-side test. The dummy tests were conducted with an R-16 seat with a three-point belt, the Delta V was 27.0+/-0.5 km/h and the maximum peak acceleration was approximately 14.6+/-0.5 g for each test. RESULTS: A new shoulder design with geometry close to that of humans was developed to be retrofitted to the THOR NT dummy. The results showed that the range of motion for the new shoulder complex during static loading was larger by at least a factor of three, for the maximum load (200 N/arm), than that of either the Hybrid III or the THOR NT; this means it was more similar to the volunteers' range of motion. It was observed that the THOR NT with the new shoulder did not slide out of the shoulder belt during a far-side collision. The performance of the new shoulder was reasonably repeatable and stable during both the static tests and the sled tests. CONCLUSION: A new shoulder for the THOR NT has been designed and developed, and data from static range of motion tests and sled tests indicate that the new shoulder complex has the potential to function in a more human-like manner on the THOR dummy.