Investigations of ash fouling with cattle wastes as reburn fuel in a small-scale boiler burner under transient conditions

Fouling behavior under reburn conditions was investigated with cattle wastes (termed as feedlot biomass [FB]) and coal as reburn fuels under a transient condition and short-time operation. A small-scale (30 kW or 100,000 Btu/hr) boiler burner research facility was used for the reburn experiments. The fuels considered for these experiments were natural gas (NG) for the ashless case, pure coal, pure FB, and blends of coal and FB. Two parameters that were used to characterize the ash "fouling" were (1) the overall heat-transfer coefficient (OHTC) when burning NG and solid fuels as reburn fuels, and (2) the combustible loss through ash deposited on the surfaces of heat exchanger tubes and the bottom ash in the ash port. A new methodology is presented for determining ash-fouling behavior under transient conditions. Results on the OHTCs for solid reburn fuels are compared with the OHTCs for NG. It was found that the growth of the layer of ash depositions over longer periods typically lowers OHTC, and the increased concentration of ash in gas phase promotes radiation in high-temperature zones during initial periods while decreasing the heat transfer in low-temperature zones. The ash analyses indicated that the bottom ash in the ash port contained a smaller percentage of combustibles with a higher FB percentage in the fuels, indicating better performance compared with coal because small particles in FB burn faster and the FB has higher volatile matter on a dry ash-free basis promoting more burn out.     

Catalyst deterioration over the lifetime of small utility engines

In this paper, the deterioration of catalysts in small, four-stroke, spark-ignition engines is described. The laboratory testing performed followed a proven test method that mimics the lifetime of a small air-cooled utility engine operating under normal field conditions. The engines used were single-cylinder, 6.5-hp, side-valve engines. These engines have a nominal 125-hr lifetime. The effectiveness of the catalysts was determined by testing exhaust emissions before and after the catalyst to determine the catalyst's efficiency. This was done several times during the lifetime of the engines to determine the deterioration in the performance of the catalysts at lowering pollutant emissions. Additional testing was performed on the catalysts to determine wear patterns, contamination, and recoverable activity. The results indicate that considerable catalyst deterioration is occurring over the lifetime of the engine. The results reveal that soot buildup, poisons, and active surface loss appear to be the contributing factors to the deterioration. These results were determined after analyzing the exhaust emissions data, scanning electron microscope results analysis, and the impact of regeneration attempts. An ANOVA statistical analysis was performed, and it was determined that the emissions are also impacted, to some degree, by time and the engine itself.     

The case for variable density: a new perspective on activated sludge settling.

A new, simple method for directly measuring activated sludge density was developed and applied, and the effects of biomass density on activated sludge settling in full-scale systems were evaluated. The driving force of sedimentation is the physical weight of the biological solids, but the role of biomass density in sedimentation has been largely ignored. Biomass density varied amongst treatment systems and this variability was correlated with settleability. Floc densities were approximately normally distributed within individual samples. Nonsoluble phosphorus content was a major contributor to density, and plants with enhanced biological phosphorus removal (EBPR) configurations generally had higher densities and better settleability than non-EBPR plants with similar filament contents. These results suggest that future work may benefit from consideration of density as a factor affecting activated sludge settling.     

Healthcare waste management: current practices in selected healthcare facilities, Botswana

Healthcare waste management continues to present an array of challenges for developing countries, and Botswana is no exception. The possible impact of healthcare waste on public health and the environment has received a lot of attention such that Waste Management dedicated a special issue to the management of healthcare waste (Healthcare Wastes Management, 2005. Waste Management 25(6) 567-665). As the demand for more healthcare facilities increases, there is also an increase on waste generation from these facilities. This situation requires an organised system of healthcare waste management to curb public health risks as well as occupational hazards among healthcare workers as a result of poor waste management. This paper reviews current waste management practices at the healthcare facility level and proposes possible options for improvement in Botswana.     

A comparison of different lysis buffers to assess allele dropout from single cells for preimplantation genetic diagnosis

Single cell polymerase chain reaction (PCR) for preimplantation genetic diagnosis (PGD) requires high efficiency and accuracy. Allele dropout (ADO), the random amplification failure of one of the two parental alleles, remains the most significant problem in PCR-based PGD testing since it can result in serious misdiagnosis for compound heterozygous or autosomal dominant conditions. A number of different strategies (including the use of lysis buffers to break down the cell and make the DNA accessible) have been employed to combat ADO with varying degrees of success, yet there is still no consensus among PGD centres over which lysis buffer should be used (ESHRE PGD Consortium, 1999 ). To address this issue, PCR amplification of three genes (CFTR, LAMA3 and PKP1) at different chromosomal loci was investigated. Single lymphocytes from individuals heterozygous for mutations within each of the three genes were collected and lysed in either alkaline lysis buffer (ALB) or proteinase K/SDS lysis buffer (PK). PCR amplification efficiencies were comparable between alkaline lysis and proteinase K lysis for PCR products spanning each of the three mutated loci (ΔF508 in CFTR 90% vs 88%; R650X in LAMA3 82% vs 78%; and Y71X in PKP1 91% vs 87%). While there was no appreciable difference between ADO rates between the two lysis buffers for the LAMA3 PCR product (25% vs 26%), there were significant differences in ADO rates between ALB and PK for the CFTR PCR product (0% vs 23%) and the PKP1 PCR product (8% vs 56%). Based on these results, we are currently using ALB in preference to PK/SDS buffer for the lysis of cells in clinical PGD. Copyright © 2001 John Wiley & Sons, Ltd.     

Identification of Mn-oxide minerals in some soils from Devon,UK, and their varying capacity to adsorb Co and Cu

A number of Mn-oxide minerals in soils from a farm in North Devon have been tentatively identified using a combination of advanced analytical techniques: scanning electron microscopy (SEM), scanning electron microprobe (SEMP), X-ray diffraction (XRD) and bulk chemical analysis by wet digestion followed by inductively-coupled plasma spectrometry (ICP). The minerals lithiophorite and hollandite are thought to occur throughout the study area although there is considerable geographical variation in the proportions of minerals present. Bimessite, vernadite, romanechite, todorokite and cryptomelane may also be present, although in smaller amounts. The use of SEMP, together with a simple sorption experiment, has allowed a study of the extent of uptake of Co and Cu by different Mn-oxide minerals. Lithiophorite appears to take up Co and Cu more effectively than hollandite within a pH range of 4–6.