氨基改性生物炭负载纳米零价铁去除水中Cr(VI)

以聚乙烯亚胺（PEI）为功能单体,玉米秸秆生物炭为载体,制备了氨基改性生物炭负载型纳米零价铁（nZVI@PEI-HBC）,并利用扫描电镜（SEM）、红外光谱（FTIR）和X射线光电子能谱（XPS）等手段对材料进行了表征,分析了溶液pH、温度、材料投加量等因素对其去除Cr（VI）的影响及其去除机理.结果表明：在投加量为0.5 g·L^-1,温度为20℃,pH值为5,Cr（VI）初始浓度为20 mg·L^-1条件下,各材料对Cr（VI）的去除率大小为nZVI@PEI-HBC > nZVI > PEI-HBC > HBC.SEM显示nZVI颗粒较均匀地分散在生物炭表面,FTIR分析表明PEI改性后材料表面增加了氨基等重金属配位基团,这可能是nZVI@PEI-HBC去除Cr（VI）效果更好的原因.影响因素研究表明,材料具有较好稳定性,老化28 d后其Cr（VI）去除性能变化不大;酸性环境、升温、增大材料投加量均有利于nZVI@PEI-HBC对Cr（VI）的去除.机理研究发现,水中溶解氧加速了nZVI的腐蚀和Fe（II）的释放,促进Cr（VI）还原为Cr（III）,然后通过共沉淀作用和氨基等基团的吸附作用被去除.     

焚烧飞灰重金属含量及浸出长期变化规律研究

通过对24个飞灰样品的重金属全量消解和高精度X射线荧光光谱法（HDXRF）快速检测结果进行线性回归分析,发现HDXRF法可较准确测定飞灰中Cu、Pb、Zn、Ni和Cd含量（线性回归决定系数R²³0.90）.采用HDXRF法对某焚烧厂飞灰重金属含量6个月快速检测及浸出毒性测定数据统计分析发现：飞灰重金属月均含量较稳定（变异系数CV<0.14）但日均含量波动较大（CV>2.54）;飞灰中Pb、Cu和Zn含量呈正相关（相关系数r>0.78）;金属浸出浓度受浸出液终点pH值影响显著,超标频率依次为Pb（68.9%）、Cd（66.1%）、Ni（24.0%）、Cu（14.2%）和Zn（1.6%）.短期飞灰金属含量和浸出毒性数据受焚烧工况,烟气处理工况和垃圾组分等多种因素共同影响,不具有代表性.为评估垃圾分类源头削减重金属效果,建议采用快速检测方法对焚烧飞灰重金属含量进行长期监测.     

基于Stacking的地面PM2.5浓度估算

为了解决地面PM_2.5监测网络在空间和时间覆盖受限的问题,提出了基于宽时空覆盖的卫星气溶胶光学厚度AOD,利用Stacking方法建立地面PM_2.5浓度估算模型,将AOD、PM_2.5和各气象参数以及与PM_2.5排放有关的数据进行训练,使用改进网格搜索对模型超参数进行优化,通过对多重共线性分析,建立基于Stacking的最优PM_2.5浓度估算模型。选取2016-01-01-2016-12-31的数据作为实验对象,结果表明:相比于随机森林、GBRT和XGBoost 3种模型,使用岭回归作为元学习器的Stacking模型性能更优,可见Stacking适用于大范围地理区域的大气污染监测。     

雨水管道沉积物中典型无机氮的干期粒径分布

以南京江北新区分流制雨水管道沉积物为研究对象,考察不同粒径沉积物中铵态氮（NH₃-N）和硝态氮（NO₃^--N）干期分布特征,分析其随干期长度的变化关系,并探讨沉积物理化性质及微生物菌群结构对NH₃-N和NO₃^--N干期分布的影响.结果表明：粒径≤0.075mm的沉积物中NH₃-N占比最高（交通区30.8%,商业区36.7%）;交通区粒径≤0.075mm的沉积物中NO₃^--N占比最高（33.0%）,而商业区粒径0.075~0.15mm沉积物中NO₃^--N占比最高（34.4%）;干期长度与交通区0.075~0.15mm粒径段的沉积物中NO₃^--N含量及商业区粒径≥0.3mm的沉积物中NH₃-N含量之间的相关性均最显著;雨水管道沉积物中NH₃-N和NO₃^--N的干期分布与O-H和N-H等官能团、表面极性和亲水性、微观形貌等有一定关联;交通区雨水管道沉积物中Gemmobacter等反硝化优势菌种（相对丰度总和为20.15%）对NO₃^--N干期分布影响更显著.     

土壤环境中微塑料的污染现状及其影响研究进展

微塑料作为一种持久性污染物,对土壤生态系统具有严重影响,土壤中微塑料的污染已愈加受到国内外学者的广泛关注。当前关于土壤环境中微塑料的研究较少,针对当前土壤中微塑料的来源、分布、降解迁移、生态效应及污染防治等方面进行综述。主要包括以下几个方面:1）概括土壤生态系统中微塑料的来源、分布特点和迁移降解规律,确定了土壤环境中微塑料的赋存状态;2）总结土壤生态系统中微塑料与其他污染物的复合效应;3）分析了微塑料对土壤理化性质、动物、植物、微生物的影响,并揭示了微塑料对于土壤生态系统的影响;4）根据土壤微塑料的分布特点、降解迁移及生态效应提出污染防治措施。最后,对今后土壤微塑料的研究重点进行了展望。     

Acceleration of floc-water separation and floc reduction with magnetic nanoparticles during demulsification of complex waste cutting emulsions

Waste cutting emulsions are difficult to treat efficiently owing to their complex composition and stable emulsified structure. As an important treatment method for emulsions, chemical demulsification is faced with challenges such as low flocs–water separation rates and high sludge production. Hence, in this study, Fe₃O₄ magnetic nanoparticles (MNPs) were used to enhance chemical demulsification performance for treating waste cutting emulsions under a magnetic field. The addition of MNPs significantly decreased the time required to attain sludge–water separation and sludge compression equilibrium, from 210 to 20 min. In addition, the volume percentage of sludge produced at the equilibrium state was reduced from 45% to 10%. This excellent flocculation–separation performance was stable over a pH range of 3–11. The magnetization of the flocculants and oil droplets to form a flocculant–MNP–oil droplet composite, and the magnetic transfer of the composite were two key processes that enhanced the separation of cutting emulsions. Specifically, the interactions among MNPs, flocculants, and oil droplets were important in the magnetization process, which was controlled by the structures and properties of the three components. Under the magnetic field, the magnetized flocculant–MNP–oil droplet composites were considerably accelerated and separated from water, and the sludge was simultaneously compressed. Thus, this study expands the applicability of magnetic separation techniques in the treatment of complex waste cutting emulsions.     

电解锰渣基方沸石的制备及其对Pb2+的吸附性能

以电解锰渣为原料,经过"弱酸除杂-碱融活化-室温陈化-晶化"水热合成反应体系,在分别外加铝源和硅源的条件下制备方沸石ANA-A及ANA-S,运用XRF、XRD、SEM-EDS和BET等表征手段对2种方沸石的化学组成、晶相结构、微观形貌和比表面积进行分析。结果表明:在煅烧温度750℃、合成温度180℃、水热反应时间8 h的条件下,外加铝源和硅源均可合成方沸石。进一步研究2种沸石对水溶液中Pb2+的静态吸附性能,其所合成的电解锰渣基ANA-A及ANA-S方沸石均可以很好地用Langmuir等温模型拟合,属于单分子层吸附,饱和吸附量分别为161.29,185.19 mg/g,对初始浓度为100 mg/L的Pb2+去除率分别为93.69%和95.47%,且均符合Lagergren准二级动力学模型,属于化学吸附;两者中ANA-S的吸附效果更好。     

底泥原位洗脱过程中氮磷含量与形态变化特征

随着城市化进程的不断推进,城市河流底泥中内源氮磷污染问题日益突出.为研究原位洗脱技术对污染底泥中氮、磷物质和成分的作用效果,以北京市凉水河作为研究对象,分别比较了现场试验洗脱与对照组0~30 cm分层底泥以及实验室模拟洗脱处理前后0~10 cm底泥中pH、E_h（氧化还原电位）、容重、含水率、OM（有机质）、TN、TP和氮、磷形态分布的变化特征.结果表明:①现场洗脱对0~5 cm厚度底泥的处理和模拟洗脱处理均对底泥中pH、E_h、含水率的改变以及其中TN、TP的去除效果表现显著,其中,现场试验洗脱组0~5 cm范围底泥中w（TN）、w（TP）分别较对照组降低了66.4%±17.4%、40.8%±24.4%,模拟洗脱处理对底泥中OM、TN、TP的去除率分别达70.1%±4.8%、66.8%±2.0%、43.1%±3.1%.②原位洗脱技术对底泥中TN的去除主要通过对PON（颗粒态有机氮）的去除来实现,现场和模拟试验过程中PON对TN去除的贡献率分别达55.0%和73.6%.③原位洗脱对底泥中TP的去除主要通过对Al-P（铝结合态磷）、OP（有机磷）的去除来实现,现场和模拟试验中Al-P、OP对TP去除的贡献率分别达37.0%、66.2%和31.3%、43.7%.研究显示,原位洗脱技术可有效去除城市河流底泥处理层中的氮磷物质,并以有机氮、磷物质的去除为主.      

Investigation to meet China II emission legislation for marine diesel engine with diesel methanol compound combustion technology

In order to reduce the pollutant emission and alleviate the pressure of petroleum resources shortage and greenhouse gas emission at the same time, the use of clean and renewable alternative fuel for marine engines is a promising option. In this study, a marine diesel engine, which was modified to run in diesel methanol compound combustion (DMCC) mode, was investigated. After the diesel injection parameters were calibrated, and combined with a sample after-treatment device DOC (diesel oxidation catalyst), the engine could meet the requirements of China II legislation. The overall MSP (methanol substitute percent) reached 54.1%. The value of each pollutant emission was much lower than that in China II emission legislation, and there was almost no methanol and formaldehyde emissions. When methanol was injected into the inlet manifold, the intake air temperature decreased a lot, as well as the exhaust gas temperature, which were beneficial to increase engine thermal efficiency and improve engine room environment. Compared with the engine running in pure diesel mode, when the engine ran in diesel/methanol dual fuel mode, the combustion phase was advanced, and the combustion duration became shorter. Therefore, the engine thermal efficiency increased, and fuel consumption decreased significantly.