Organophosphate flame retardants and plasticisers in wastewater treatment plants

Previous studies have revealed that chlorinated and non-chlorinated organophosphorous flame retardants and plasticisers are important contaminants in German surface waters and it has been demonstrated that wastewater treatment plants contribute to the emission of these substances. In this study temporal development as well as elimination efficiency were determined in two wastewater treatment plants (STP) in the Ruhr/Rhine area at different stages of the wastewater treatment process. The samples were analysed for the non-chlorinated organophosphate esters tri-n-butylphosphate (TnBP), tri-iso-butylphosphate (TiBP), tris-(butoxyethyl)-phosphate (TBEP) and triphenylphosphate (TPP) and the chlorinated organophosphate esters tris-(2-chloro, 1-methylethyl)-phosphate (TCPP), tris-(2-chloro-, 1-chloromethylethyl)-phosphate (TDCP) and tris-(2-chloroethyl)-phosphate (TCEP). The study showed that there were significant differences in the elimination of chlorinated and non-chlorinated organophosphorous flame retardants. The elimination rates ranged from 57-86% for TiBP, TnBP and TBEP at both STP's. No elimination of the chlorinated flame retardants TCPP, TDCP and TCEP was observed in any of the sampled STPs. At both STPs the first treatment steps and the final filtration did not contribute to the elimination of the non-chlorinated organophosphorous flame retardants while the aeration step did. At both STPs the efficiency of the cleaning process concerning the flame retardants was comparable. Thus the type of construction of the STP was not relevant for the elimination of these substances. Additionally a strong day-to-day variation was observed, while in one STP a temporal trend for TCPP during the week was found.     

High frequency monitoring of the coastal marine environment using the MAREL buoy

The MAREL Iroise data buoy provides physico-chemical measurements acquired in surface marine water in continuous and autonomous mode. The water is pumped 1.5 m from below the surface through a sampling pipe and flows through the measuring cell located in the floating structure. Technological innovations implemented inside the measuring cell atop the buoy allow a continuous cleaning of the sensor, while injection of chloride ions into the circuit prevents biological fouling. Specific sensors for temperature, salinity, oxygen and fluorescence investigated in this paper have been evaluated to guarantee measurement precision over a 3 month period. A bi-directional link under Internet TCP-IP protocols is used for data, alarms and remote-control transmissions with the land-based data centre. Herein, we present a 29 month record for 4 parameters measured using a MAREL buoy moored in a coastal environment (Iroise Sea, Brest, France). The accuracy of the data provided by the buoy is assessed by comparison with measurements of sea water weekly sampled at the same site as part of SOMLIT (Service d'Observation du Milieu LIToral), the French network for monitoring of the coastal environment. Some particular events (impact of intensive fresh water discharges, dynamics of a fast phytoplankton bloom) are also presented, demonstrating the worth of monitoring a highly variable environment with a high frequency continuous reliable system.     

Quantitative PCR analysis of house dust can reveal abnormal mold conditions

Indoor mold concentrations were measured in the dust of moldy homes (MH) and reference homes (RH) by quantitative PCR (QPCR) assays for 82 species or related groups of species (assay groups). About 70% of the species and groups were never or only rarely detected. The ratios (MH geometric mean : RH geometric mean) for 6 commonly detected species (Aspergillus ochraceus, A. penicillioides, A. unguis, A. versicolor, Eurotium group, and Cladosporium sphaerospermum) were >1 (Group I). Logistic regression analysis of the sum of the logs of the concentrations of Group I species resulted in a 95% probability for separating MH from RH. These results suggest that it may be possible to evaluate whether a home has an abnormal mold condition by quantifying a limited number of mold species in a dust sample. Also, four common species of Aspergillus were quantified by standard culturing procedures and their concentrations compared to QPCR results. Culturing underestimated the concentrations of these four species by 2 to 3 orders of magnitude compared to QPCR.     

Organochlorine Pesticide Residues in Wheat and Drinking Water Samples from Jaipur, Rajasthan, India

The organochlorine pesticide contamination in dietary sources has caused serious threat to the human progeny. The present study was therefore conducted to evaluate the pesticide contamination in wheat flour and drinking water from Jaipur City, Rajasthan, India using Gas Chromatograph. All the wheat and water samples were found to be contaminated with various organochlorine pesticide residues of DDT and its metabolites, HCH and its isomers, heptachlor and its expoxide and aldrin. The amount of pesticide detected in wheat flour was higher than the permissible limits prescribed by WHO/FAO. In drinking water only a few pesticides exceeded the permissible limits. Seasonal variations of pesticides residues were also observed during the study period.     

A comparison of X-ray fluorescence and wet chemical analysis of air filter samples from a scrap lead smelting operation

Personal and area air samples were taken at a scrap lead smelter operation in a bullet manufacturing facility. Samples were taken using the 37-mm styrene-acrylonitrile closed-face filter cassette (CFC, the current US standard device for lead sampling), the 37-mm GSP or "cone" sampler, the 25-mm Institute of Occupational Medicine (IOM) inhalable sampler, and the 25-mm Button sampler (developed at the University of Cincinnati). Polyvinylchloride filters were used for sampling. The filters were pre- and post-weighed, and analyzed for lead content using a field-portable X-ray fluorescence (XRF) analyzer. The filters were then extracted with dilute nitric acid in an ultrasonic extraction bath and the solutions were analyzed by inductively coupled plasma optical emission spectroscopy. The 25-mm filters were analyzed using a single XRF reading, while three readings on different parts of the filter were taken from the 37-mm filters. The single reading from the 25-mm filters was adjusted for the nominal area of the filter to obtain the mass loading, while the three readings from the 37-mm filters were inserted into two different algorithms for calculating the mass loadings, and the algorithms were compared. The IOM sampler was designed for material collected in the body of the sampler to be part of the collected sample as well as that on the filter. Therefore, the IOM sampler cassettes were rinsed separately to determine if wall-loss corrections were necessary. All four samplers gave very good correlations between the two analytical methods above the limit of detection of the XRF procedure. The limit of detection for the 25-mm filters (5 microg) was lower than for the 37-mm filters (10 microg). The percentage of XRF results that were within 25% of the corresponding ICP results was evaluated. In addition, the bias from linear regression was estimated. Linear regression for the Button sampler and the IOM sampler using single readings and the GSP using all tested techniques for total filter loading gave acceptable XRF readings at loadings equivalent to sampling at the OSHA 8-hour Action Level and Permissible Exposure Limit. However, the CFC only had acceptable results when the center reading corrected for filter area was used, which was surprising, and may be a result of a limited data set. In addition to linear regression, simple estimation of bias indicated reasonable agreements between XRF and ICP results for single XRF readings on the Button sampler filters, (82% of the individual results within criterion), and on the IOM sampler filters (77% or 61%--see text), and on the GSP sampler filters using the OSHA algorithm (78%). As a result of this pilot project, all three samplers were considered suitable for inclusion in further field research studies.     

Development and validation of methods for environmental monitoring of cyclophosphamide in workplaces

Methods to monitor contamination of workplaces with antineoplastic drugs have been developed and validated. Cyclophosphamide (CP) was used as a model compound as it is one of the most commonly used antineoplastic drugs. A wipe sampling method to detect contamination with CP at surfaces was developed. A personal air sampling method to sample gas and vapour on solid sorbent tubes and particles with filters was also developed. Wipe and filter samples were extracted and sorbent samples were eluted, all with ethyl acetate. The samples were analysed with liquid chromatography tandem mass spectrometry. (2)H(6)-labelled cyclophosphamide was used as an internal standard. The between-day precision was 2-5% for wipe samples, 4-6% for sorbent samples and 3-8% for filter samples. The limit of detection was 0.02 ng CP per sample for the wipe and filter methods and 0.03 ng CP per sample for the solid sorbent method. Wipe sampling on surfaces made of different materials resulted in mean recoveries between 78-106%. The desorption recovery was between 97-102% for the wipe samples, 97% for the sorbent samples and 101% for the filter samples. Samples were stable for up to 2 months at 5 degrees C and -20 degrees C and for about 2 d at room temperature. The developed methods were applied to the measurement of contamination with CP in a hospital pharmacy. Trace amounts of CP, 1.3 and 1.4 ng, were detected on surfaces in the pharmacy.     

Evaluation of forest nutrition based on large-scale foliar surveys: are nutrition profiles the way of the future?

This paper introduces the use of nutrition profiles as a first step in the development of a concept that is suitable for evaluating forest nutrition on the basis of large-scale foliar surveys. Nutrition profiles of a tree or stand were defined as the nutrient status, which accounts for all element concentrations, contents and interactions between two or more elements. Therefore a nutrition profile overcomes the shortcomings associated with the commonly used concepts for evaluating forest nutrition. Nutrition profiles can be calculated by means of a neural network, i.e. a self-organizing map, and an agglomerative clustering algorithm with pruning. As an example, nutrition profiles were calculated to describe the temporal variation in the mineral composition of Scots pine and Norway spruce needles in Finland between 1987 and 2000. The temporal trends in the frequency distribution of the nutrition profiles of Scots pine indicated that, between 1987 and 2000, the N, S, P, K, Ca, Mg and Al decreased, whereas the needle mass (NM) increased or remained unchanged. As there were no temporal trends in the frequency distribution of the nutrition profiles of Norway spruce, the mineral composition of the needles of Norway spruce needles subsequently did not change. Interpretation of the (lack of) temporal trends was outside the scope of this example. However, nutrition profiles prove to be a new and better concept for the evaluation of the mineral composition of large-scale surveys only when a biological interpretation of the nutrition profiles can be provided.     

Using improved neural network model to analyze RSP,NOx and NO2 levels in urban air in Mong Kok,Hong Kong

As the health impact of air pollutants existing in ambient addresses much attention in recent years, forecasting of airpollutant parameters becomes an important and popular topic inenvironmental science. Airborne pollution is a serious, and willbe a major problem in Hong Kong within the next few years. InHong Kong, Respirable Suspended Particulate (RSP) and NitrogenOxides NO_x and NO₂ are major air pollutants due to thedominant diesel fuel usage by public transportation and heavyvehicles. Hence, the investigation and prediction of the influence and the tendency of these pollutants are ofsignificance to public and the city image. The multi-layerperceptron (MLP) neural network is regarded as a reliable andcost-effective method to achieve such tasks. The works presentedhere involve developing an improved neural network model, whichcombines the principal component analysis (PCA) technique and theradial basis function (RBF) network, and forecasting thepollutant levels and tendencies based in the recorded data. Inthe study, the PCA is firstly used to reduce and orthogonalizethe original input variables (data), these treated variables arethen used as new input vectors in RBF neural network modelestablished for forecasting the pollutant tendencies. Comparingwith the general neural network models, the proposed modelpossesses simpler network architecture, faster training speed,and more satisfactory predicting performance. This improvedmodel is evaluated by using hourly time series of RSP, NO_x and NO₂ concentrations collected at Mong Kok Roadside Gaseous Monitory Station in Hong Kong during the year 2000. By comparing the predicted RSP, NO_x and NO₂ concentrationswith the actual data of these pollutants recorded at the monitorystation, the effectiveness of the proposed model has been proven.Therefore, in authors' opinion, the model presented in the paper is a potential tool in forecasting air quality parameters and hasadvantages over the traditional neural network methods.     

Trihalomethanes in Drinking Water of Greater Québec Region (Canada): Occurrence, Variations and Modelling

The levels of trihalomethanes (THMs) – the main species of by-product from water chlorination – were monitored in thedistribution systems of the five major drinking water utilitiesof the greater area of Québec City in order to investigate andmodel their occurrence on a spatial and seasonal basis. Data forTHMs and other water quality and operational parametersassociated with their formation were generated through a 16 monthsampling program involving several sites representing variablewater residence times, from the plant to the system extremity.The results demonstrate that the differences in measured THMlevels between the five utilities are mainly due to the variablequality of raw waters, the type of water treatment process beingused and the type and levels of applied disinfectant. Dependingon the utility, average THM levels were from 1.3 to 2.5 timeshigher in the system extremities than in the water leaving thetreatment plant. Also, average levels of THMs measured in summerat the distribution system extremities were, depending on theutility, from 2.5 to 5 times higher than the average levelsmeasured in winter. The seasonal differences were found to besignificantly greater than those observed by others in waterutilities in the United States and Europe and are explained inlarge part by the considerable changes, over the year, in thequality and temperature of surface waters in Southern Québec. Forthe five utilities under study, multivariate regression modelswere developed in order to predict spatial and seasonalvariations of THMs. Both residual chlorine demand and temperaturewere found to be better, statistically, as predictors for THMoccurrence. The usefulness of the developed models for routineand long term water quality management, as well as for assessmentof human exposure to THMs, are also discussed.     

Sharing the geo-Referenced Results of Climate Change Impact Research

The Prairie Adaptation Research Collaborative (PARC) has implemented an Internet Map Server (IMS) at the PARC web site (www.parc.ca) to 1) disseminate the geo-referenced results of PARC sponsored research on climate change impacts and adaptation, and 2) address data, information and knowledge management within the PARC network of researchers and partners. PARC facilitates interdisciplinary research on adaptation to the impacts of climate change in the Canadian Prairie Provinces. The web site is intended as a platform for sharing information and encouraging discussion of climate change impacts and adaptation. The IMS enables scientists and stakeholders to apply simple climate change scenarios to geo-referenced biophysical and social data, and dynamically create maps that display the geographic distribution of potential impacts of climate change. With a limited capacity for spatial analysis, most geo-processing and the climate impact modeling is done offline within a GIS environment. The IMS will serve the output from climate impact models, such that the model results can be customized by the web site user and be most readily applied to the planning and analysis of adaptation strategies.