Influence of HCl on oxidation of gaseous elemental mercury by dielectric barrier discharge process

The influence of HCl on the oxidation of gaseous elemental mercury (Hg0) has been investigated using a dielectric barrier discharge (DBD) plasma process, where the temperature of the plasma reactor and the composition of gas mixtures of HCl, H2O, NO, and O2 in N2 balance have been varied. We observe that Cl atoms and Cl2 molecules, created by the DBD process, play important roles in the oxidation of Hg0 to HgCl2. The addition of H2O to the gas mixture of HCl in N2 accelerates the oxidation of Hg0, although no appreciable effect of H2O alone on the oxidation of Hg0 has been observed. The increase of the reaction temperature in the presence of HCl results in the reduction of Hg0 oxidation efficiency probably due to the deterioration of the heterogeneous chemical reaction of Hg0 with chlorinated species on the reactor wall. The presence of NO shows an inhibitory effect on the oxidation of Hg0 under DBD of 16% O2 in N2, indicating that NO acts as an O and O3 scavenger. At the composition of Hg0 (280 microg m(-3)), HCl (25 ppm), NO (204 ppm), O2 (16%) and N2 (balance) and temperature 90 degrees C, we obtain the nearly complete oxidation of Hg0 at a specific energy density of 8 J l(-1). These results lead us to suggest that the DBD process can be viable for the treatment of mercury released from coal-fired power plants.     

Characteristics of liquid product from the pyrolysis of waste plastic mixture at low and high temperatures: influence of lapse time of reaction

Pyrolysis of a waste plastic mixture (high-density polyethylene: low-density polyethylene: polypropylene: polystyrene = 3:2:3:1) into a liquid product was carried out in a stirred semi-batch reactor at low (350 degrees C) and high (400 degrees C) temperatures. The effect of lapse time of reaction in the reactor and also degradation temperature on the characteristics of the liquid product from pyrolysis of the mixture was investigated. Liquid products were described by cumulative amount distribution, paraffin, olefin, naphthene and aromatic (PONA) distribution and molecular weight distribution. Their characteristic was quite differed with a lapse time of reaction and also at a low and high degradation temperatures, because of the different physicochemical properties of the plastic types in the mixture. With increase of lapse time of reaction, the order for the main products in PONA components obtained at 350 degrees C was firstly aromatic products and then olefin products, while at 400 degrees C the order was firstly aromatic products, then olefin products and finally paraffin products. The experiments also showed from the molecular weight distribution of liquid PONA components that the paraffin and olefin products had a wide distribution by mainly random scission of polymer, but in the case of olefin products were produced by an end-chain scission mechanism as well as random scission mechanism, as evidenced by much more light olefin products. This phenomenon was evident at a higher degradation temperature. Also, both the light olefin and naphthene products with a molecular weight of around 120, as a main product, showed a similar trend as a function of lapse time, which had a maximum fraction at 343 min (at 350 degrees C) and 83 min (at 400 degrees C). Among PONA components, the highest concentrations of aromatic products were obtained with a molecular weight of around 100 at the fastest lapse time of reaction, regardless of degradation temperature. It was concluded that the characteristics of liquid product on the pyrolysis of plastic mixtures were strongly influenced by lapse time of reaction and degradation temperature.     

Preparation of coal slurry with organic solvents

In this study, various organic solvents were used to prepare coal slurries and the rheological and thermal properties of coal-organic solvent slurries were examined. Solvents with molecules containing unpaired electrons (high basicity) show high extraction power and cause swelling of coal. Therefore, coal-organic solvent slurries usually showed higher viscosities compared to coal-water slurry. In addition, coal slurries prepared by alcohols and cyclohexanone demonstrated lower settling rates but a high specific sedimentation volume presumably because these solvents swelled coal particles well and led to the formation of weak gel structures in the bulk. In addition, ethanol and cyclohexanone are capable of breaking a considerable amount of hydrogen bonds in coal and subsequently opening up the structures. Thus, more surface area is available for combustion and the combustion rate of coal slurries was increased.     

Study on integrated management of PCB containing waste and PCB contaminated waste: proposal of new congeners for quantification

In the present study, new congeners were selected for the efficient management of PCB containing waste and PCB contaminated waste, and the applicability of these new indicators was confirmed. As a result, 8 indicator congeners and 4 index peaks which were named “Proposed new method 1” and “Proposed new method 2” were selected. For the assessment of a novel quantitative method, comparative tests using conventional methods were conducted, and the factors for total PCB were calculated for each method. Results from these tests showed that the average values for the factors of CEN/TC19/WG22, DIN 51527, and the test method by the disposal regulation for ocean dumping in Korea were 1.86, 3.47, and 2.52, respectively, while those for the proposed new method 1 and proposed new method 2 were 2.98 and 5.56, respectively. For PCB contaminated waste, the factor was found to be 1.99, 3.42, and 3.02 using the conventional methods, 2.67 using the proposed new method 1, and 5.57 using the proposed new method 2. It is expected that, in accordance with the results of the present study, the management of PCB waste can be integrated, regardless of the type of waste involved.     

Butyltin residues in blue mussels (Mytilus edulis) and arkshells (Scapharca broughtonii) collected from Korean coastal waters

Butyltin compounds (BTs) including tributyltin (TBT) and its degradation products, di- (DBT) and mono-butyltin (MBT), were determined in bivalves such as blue mussels (Mytilus edulis) and arkshells (Scapharca broughtonii) collected from Korean coastal waters. BTs were detected in all the blue mussels and arkshells analyzed. The concentrations of total butyltin (sigmaBTs: MBT + DBT + TBT) in blue mussels and arkshells ranged from 49 to 2500 ng/g and 29 to 87 ng/g wet weight, respectively. Higher concentrations of BTs were found in blue mussels collected from Okpo and Kohyonsong Bays and Jangsengpo Harbor where large shipyards and harbors are located with dry-dock facilities. This suggested that maritime activities nearby the harbors play a major role as the source of BTs. Concentrations of TBT in mussels collected from Korea were one of the highest values reported, suggesting ongoing TBT contamination in Korea. Among BTs, TBT was the predominant compound both in blue mussels and arkshells collected from almost all the sampling locations, indicating the fresh input of TBT in Korean coastal waters. Smaller mussels tended to accumulate BTs at higher concentrations than larger ones, which may be due to higher filtration rate of small mussels and/or contact with surface microlayer in intertidal zones.     

Precipitation of swine and cattle manure phosphorous using limestone dust

The effectiveness of SPS and PULPRO, fine limestone dusts, in precipitating swine and dairy manure phosphorous (P) was determined in the laboratory. Both manures were sieved before being treated with limestone, to reproduce the treatment of mechanically separated manure and to observe the precipitation effect of limestone without that of the large manure solid particles. P precipitation was optimized by varying precipitation conditions (propeller blade speeds, mixing time and limestone levels) and limestone particle size. P precipitation was optimized using a propeller blade mixing speed of 0.3 m s(-1) for at least 5 minutes, using 3% limestone (dry limestone mass over wet manure mass). In terms of particle size, PULPRO 20 (limestone with a particle size of 0.02 mm) produced the most P precipitation and the smallest volume and mass of sludge, as compared to PULPRO 10, PULPRO 3 and SPS (limestone with a particle size of 0.01, 0.003 and 0.3 to 0.003 mm, respectively). For both 9.5% TS (total solids) dairy and 8.8% TS swine manure, mechanical separation followed by limestone precipitation concentrated 90% of manure TS and TP in a sludge volume representing 45% of the initial raw manure mass.     

Cadmium ion sorption onto lignocellulosic biosorbent modified by sulfonation: the origin of sorption capacity improvement

Juniper (Juniperus monosperma), a small-diameter underutilized material, has been studied as a lignocellulosic biosorbent for removing heavy metals from water. In this study, juniper wood was modified by sulfonation to enhance sorption capacity for cadmium in water. The origin of the enhancement was investigated by observing the sorption behaviors and the change in surface functional group concentrations. Cadmium sorption by all juniper wood biosorbents studied was fast and the sorption capacity decreased with decreasing pH, similar to results found for other biosorbents. Sulfonated juniper was found to have at least twice the sorption capacity for cadmium removal from water compared to that of untreated juniper, though the sorption capacity increased with increasing pH. A slight increase in carboxylate content after sulfonation was likely responsible for a small portion of the enhancement. Elemental analysis showed an increase in sulfur content after sulfonation. Diffuse reflectance infrared Fourier transform (DRIFT) spectra showed a decrease in the band at 1660 cm(-1) in the range of carbonyl groups as a result of sulfonation. This indicates that coniferaldehyde groups in the lignin of juniper wood corresponding to this band were substituted into sulfonic acid groups after sulfonation. This interpretation was supported by both the color forming reaction with phloroglucinol-hydrochloric acid and the reaction mechanisms from the acid sulfite pulping process. Consequently, the enhancement of cadmium sorption capacity of juniper wood by sulfonation mainly originated from the production of sulfonic acid groups, which are binding sites for heavy metals.     

Brominated flame retardants and heavy metals in automobile shredder residue (ASR) and their behavior in the melting process

The End-of-life Vehicles Recycling Act went into effect on January 1, 2005, in Japan and requires the proper treatment of airbags, chlorofluorocarbons (CFCs), and automobile shredder residue (ASR). The need for optimal treatment and recycling of ASR, in particular, has been increasing year after year because ASR is regarded as being difficult to treat. Dioxin-related compounds, brominated flame retardants (BFRs), heavy metals, chlorine and organotin compounds are all present in high concentrations in ASR. The authors conducted ASR melting treatment tests using a 10-tons/day-scale direct melting system (DMS), which employs shaft-type gasification and melting technology. The results obtained showed that dioxin-related compounds and BFRs were decomposed by this melting treatment. The high-temperature reducing atmosphere in the melting furnace moved volatile heavy metals such as lead and zinc into the fly ash where they were distributed at a rate of more than 90% of the input amount. This treatment was also found to be effective in the decomposition of organotin, with a rate of decomposition higher than 99.996% of the input amount. Via the recovery of heavy metals concentrated in the fly ash, all the products discharged from this treatment system were utilized effectively for the complete realization of an ASR recycling system that requires no final disposal sites.     

An intercalibration study on organobromine compounds: Results on polybrominated diphenylethers and related dioxin-like compounds

An intercalibration study on organobromine compounds has been conducted to evaluate the accuracy and reliability in the analysis of brominated flame retardants (BFRs) such as polybrominated diphenyl ethers (PBDEs) and their related compounds like polybrominated and monobromo-polychlorinated dibenzodioxins and -furans (PBDDs/DFs, MoBPCDDs/DFs). This paper reports the results for these compounds in 'Mixed Standard Solutions' and 'Air-Dried Sediment'. The relative standard deviations (RSDs) for PBDEs, PBDDs/DFs and MoBPCDDs/DFs in mixed standard solutions ranged from 9% to 24%, 4% to 20% and 8% to 27%, respectively. The results of this study are better than those reported in earlier international interlaboratory studies due to general improvement in analytical methods and an increasing number of available authentic standards, particularly for PBDEs. In the analysis for higher brominated compounds such as octabromodibenzodioxin, the participants were advised to optimize the calibration curves befitting the range of concentrations found in samples because variation of relative response factors was noted. The results for 'Air-Dried Sediment' were also reasonable with RSDs from 10% to 38% for PBDEs, 8% to 38% for PBDDs/DFs and 17% to 36% for MoBPCDDs/DFs. In the sediment sample, possible errors in the sample pretreatment and/or interference by other compounds/impurities were indicated. The concentrations of pentabromodiphenylether, BDE100, varied more than the other PBDE isomers due to its poor separation in some chromatographic conditions. In addition, interference by PBDEs was observed in the analysis for PBDFs. Potential degradation/secondary formulation of PBDEs and PBDFs during the Soxhlet extraction were suggested when copper powder was added into the sediment samples. Inspite of these observations, the results in this study are better than those reported in other interlaboratory studies due to the advice given to participants for improving the results. Compared with the results for PCDDs/DFs (5-23% RSDs) and Co-PCBs (6-24% RSDs), the RSDs for most of the organobromine compounds were high, indicating an immature QA/QC approach for the analysis of PBDEs and related compounds in comparison to common chlorinated dioxins.