An assessment of land-based climate and carbon reversibility in the Australian Community Climate and Earth System Simulator

Future levels of climate change depend not only on carbon emissions but also on carbon uptake by the land and the ocean. Here we are using the Earth system model (ESM1) version of the Australian Community Climate and Earth System Simulator (ACCESS) to explore the potential and impact of removing carbon dioxide (CO₂) from the atmosphere through the climate and carbon cycle reversibility experiment. This experiment builds on the standard Coupled Model Intercomparison Project (CMIP) experiment, increasing CO₂ at 1% per year until 4xCO₂ is reached. The atmospheric CO₂ levels are then decreased at the same rate which brings the CO₂ back to pre-industrial levels. We then continue to run the model with constant CO₂ for another 350 years. Our analysis focuses on the response of the land carbon cycle. We find that carbon stores are largely reversible at the global scale over the timescale of changing CO₂. However, carbon stores continue to decrease after CO₂ returns to its initial value, and the land loses another 40 Pg of carbon (PgC) with the largest change in the tropics. It takes about 300 years beyond the period of changing CO₂ for the carbon stores to recover. Interestingly, we saw strong regional variations in the strength of the land response to changing CO₂. Australia showed the largest increase/decrease in biomass carbon (about 40%) and the largest variability in productivity, which was strongly correlated with rainfall. This highlights the importance of assessing the regional response to understanding the processes underlying the response and the sensitivity of these processes within each model. This understanding will benefit future multi-model analyses of this reversibility experiment. It also illustrates more generally the potential to use Earth system model experiments as part of the evaluation of proposed applications of carbon dioxide removal (CDR) technologies. As such, we recommend that these types of modelling experiments be included when mitigation policies are developed.

     

A comparison of X-ray fluorescence and wet chemical analysis of air filter samples from a scrap lead smelting operation

Personal and area air samples were taken at a scrap lead smelter operation in a bullet manufacturing facility. Samples were taken using the 37-mm styrene-acrylonitrile closed-face filter cassette (CFC, the current US standard device for lead sampling), the 37-mm GSP or "cone" sampler, the 25-mm Institute of Occupational Medicine (IOM) inhalable sampler, and the 25-mm Button sampler (developed at the University of Cincinnati). Polyvinylchloride filters were used for sampling. The filters were pre- and post-weighed, and analyzed for lead content using a field-portable X-ray fluorescence (XRF) analyzer. The filters were then extracted with dilute nitric acid in an ultrasonic extraction bath and the solutions were analyzed by inductively coupled plasma optical emission spectroscopy. The 25-mm filters were analyzed using a single XRF reading, while three readings on different parts of the filter were taken from the 37-mm filters. The single reading from the 25-mm filters was adjusted for the nominal area of the filter to obtain the mass loading, while the three readings from the 37-mm filters were inserted into two different algorithms for calculating the mass loadings, and the algorithms were compared. The IOM sampler was designed for material collected in the body of the sampler to be part of the collected sample as well as that on the filter. Therefore, the IOM sampler cassettes were rinsed separately to determine if wall-loss corrections were necessary. All four samplers gave very good correlations between the two analytical methods above the limit of detection of the XRF procedure. The limit of detection for the 25-mm filters (5 microg) was lower than for the 37-mm filters (10 microg). The percentage of XRF results that were within 25% of the corresponding ICP results was evaluated. In addition, the bias from linear regression was estimated. Linear regression for the Button sampler and the IOM sampler using single readings and the GSP using all tested techniques for total filter loading gave acceptable XRF readings at loadings equivalent to sampling at the OSHA 8-hour Action Level and Permissible Exposure Limit. However, the CFC only had acceptable results when the center reading corrected for filter area was used, which was surprising, and may be a result of a limited data set. In addition to linear regression, simple estimation of bias indicated reasonable agreements between XRF and ICP results for single XRF readings on the Button sampler filters, (82% of the individual results within criterion), and on the IOM sampler filters (77% or 61%--see text), and on the GSP sampler filters using the OSHA algorithm (78%). As a result of this pilot project, all three samplers were considered suitable for inclusion in further field research studies.     

Optimization of a multielement sequential extraction method employing an experimental design approach for metal partitioning in soils and sediments

The optimisation of a simple multielement extraction method employing an experimental design approach is described. The method uses centrifugation to pass one extractant solution at varying pH through a contaminated soil sample. The nature and concentration of the acid, rate of centrifugation and time, number of sequential leachates and the ratio of extractant volume: sample weight have been studied in order to obtain the optimum conditions for extraction. A fractional factorial experimental design was performed, and the results were used to identify significance which was then evaluated by carrying out a central composite experimental approach. Once optimum conditions had been obtained, sequential leaches were analysed by ICP-AES and chemometrics were employed to identify the composition of each component. Comparisons have been made with previous studies and tentative assignments, based on well defined separated fractions and percentage compositions for individual elements, used to identify the different physico-chemical components in the sample.     

An application of circular-linear correlation analysis to the relationship between Freon concentration and wind direction in Woods Hole,Massachusetts

Two statistical tests for correlation between a circular variate and a linear variate are presented. The tests are applied to a small data set concerning Freon-12 concentration and wind direction in Woods Hole, Massachusetts during the summer of 1987. A significant correlation is found. Further analysis suggests that this directional effect is related to onshore Freon-12 release.Woods Hole Oceanographic Institution Contribution Number 6750