精神活性物质在北京市某污水处理厂中的污染特征与生态风险

为了解污水处理厂对精神活性物质的去除特征及总出水对受纳水体的生态风险,采用固相萃取-高效液相色谱-串联质谱法调查了北京市某污水处理厂中13种精神活性物质的浓度水平与负荷量变化,并运用RQ（risk quotient,风险熵）对总出水中精神活性物质进行风险评估.结果表明:①13种精神活性物质在总进水与总出水中均能检出,总质量浓度平均值分别为2 395.10和63.59 ng/L,其中ρ（EPH）（EPH表示麻黄碱）占比分别为93.9%和67.9%,其次为COD（可待因）与METH（甲基苯丙胺）.污水处理厂上游地表水中ρ（EPH）、ρ（METH）与ρ（KET）（KET为氯胺酮）均高于总出水及其下游地表水,说明上游沿河可能有新的污染源输入.②污水处理厂对NK（去甲氯胺酮）、BE（苯甲酰爱康宁）和MTD（美沙酮）均呈负去除,其他精神活性物质的去除主要发生在二级生物处理与三级处理（超滤膜与UV消毒）阶段.③污水处理厂服务区域内精神活性物质的周内负荷量存在一定波动,AMP（苯丙胺）、METH、MDA（3,4-亚甲二氧基苯丙胺）、MDMA（3,4-亚甲二氧基甲基苯丙胺）、KET与HER（海洛因）的负荷量均在周末升高.④污水处理厂总出水中精神活性物质的生态风险均较低（RQ < 0.10）.研究显示,污水处理厂不能完全去除污水中的精神活性物质,总出水中残留精神活性物质对受纳河流生态系统产生的长期混合效应不容忽视.      

不同浓度锌处理下水稻幼苗对镉的累积效应

为探究锌（Zn）对水稻镉（Cd）累积的影响及其根表铁膜所发挥的作用,选取Cd高累积型水稻品种中9优547（简称"Z547"）和Cd低累积型水稻品种金优402（简称"J402"）,采用温室水培试验,研究0、2、5、10、15和20 μmol/L等6个Zn浓度下水稻幼苗对Cd的累积效应,以及不同浓度Zn处理对根表铁膜生成量的影响.结果表明:①随着c（Zn）的增加,Z547和J402水稻幼苗生物量均呈先增后减的趋势,分别在c（Zn）为2和10 μmol/L时达到最大值.②Z547和J402水稻幼苗中w（Cd）均呈先降后增的趋势,分别在c（Zn）为5和2 μmol/L时达到最小值;当水稻幼苗中w（Cd）达到最小值时,Z547根和地上部中w（Cd）分别为31.65和11.47 mg/kg,J402根和地上部中w（Cd）分别为22.58和14.36 mg/kg.③不同浓度Zn处理下水稻幼苗各部位中w（Cd）均与根表铁膜中w（Mn）、w（Fe）、w（Fe+Mn）呈显著正相关,高铁膜处理水稻幼苗中w（Cd）显著高于低铁膜处理,表明根表铁膜生成量的增加会促进Cd在水稻幼苗中的累积.研究显示,当c（Zn）较低时,c（Zn）的增加会抑制水稻幼苗对Cd的累积;当c（Zn）较高时,c（Zn）的增加会促进水稻幼苗对Cd的累积,而Zn可通过控制根表铁膜的生成来影响水稻幼苗对Cd的累积.      

基于边介数的省域生态廊道构建方法优化

我国城市建设和生态保护工作均对土地资源有大量需求,二者之间的矛盾在经济优先发展区表现尤为明显.为了有效地改善生态环境,管控土地利用并引导其变化发展,需要建设具备不可替代特征的省域生态廊道.最小累积阻力模型（minimum cumulative resistance,MCR）是识别生态廊道最常用、有效的模型,但在应用于省域尺度时,MCR模型识别的潜在廊道路由存在冗余的问题.因此,通过引入网络科学中的边介数指数（edge-betweenness）对MCR模型进行优化,计算潜在廊道路由的边介数指数值,选取出其中最为重要和简明的结构来连通生态源地,即提取潜在路由中的骨干路由（backbone route）和关键战略点（key strategic point）作为不可替代的结构来指导省域生态廊道建设.将优化后的MCR模型应用于广东省,构建了全长5 493 km的省域生态廊道,其中包含生态源地20处,关键战略点11个,骨干生态廊道29条.骨干路由与关键战略点构成的不可替代省域生态廊道（irreplaceable provincial corridor）能够实现"廊道数量和占地面积最少、连通性基本不变"的目标.研究显示,边介数能够对潜在路由进行优化筛选,识别出维护省域生态安全的关键结构;不可替代生态廊道能够指导省域生态规划和土地空间的发展利用,并为更高水平的生态安全环境提供了演进的基础;同时也为土地资源紧张的地区提供了建设生态廊道的参考与依据.      

On-going nitrification in chloraminated drinking water distribution system (DWDS) is conditioned by hydraulics and disinfection strategies

Within the drinking water distribution system (DWDS) using chloramine as disinfectant, nitrification caused by nitrifying bacteria is increasingly becoming a concern as it poses a great challenge for maintaining water quality. To investigate efficient control strategies, operational conditions including hydraulic regimes and disinfectant scenarios were controlled within a flow cell experimental facility. Two test phases were conducted to investigate the effects on the extent of nitrification of three flow rates (Q = 2, 6, and 10 L/min) and four disinfection scenarios (total Cl₂=1 mg/L, Cl₂/NH₃-N=3:1; total Cl₂=1 mg/L, Cl₂/NH₃-N=5:1; total Cl₂=5 mg/L, Cl₂/NH₃-N=3:1; and total Cl₂=5 mg/L, Cl₂/NH₃-N=5:1). Physico-chemical parameters and nitrification indicators were monitored during the tests. The characteristics of biofilm extracellular polymetric substance (EPS) were evaluated after the experiment. The main results from the study indicate that nitrification is affected by hydraulic conditions and the process tends to be severe when the fluid flow transforms from laminar to turbulent (2300<Re<4000). Increasing disinfectant concentration and optimizing Cl₂/NH₃-N mass ratio were found to inhibit nitrification to some extend when the system was running at turbulent condition (Q = 10 L/min, Re = 5535). EPS extracted from biofilm that was established at the flow rate of 6 L/min had greater carbohydrate/protein ratio. Furthermore, several nitrification indicators were evaluated for their prediction efficiency and the results suggest that the change of nitrite, together with total organic carbon (TOC) and turbidity can indicate nitrification potential efficiently.     

Coupling mechanism of activated carbon mixed with dust for flue gas desulfurization and denitrification

To clarify the effect of coking dust, sintering dust and fly ash on the activity of activated carbon for various industrial flue gas desulfurization and denitrification, the coupling mechanism of the mixed activated carbon and dust was investigated to provide theoretical reference for the stable operation. The results show that coking dust had 34% desulfurization efficiency and 10% denitrification efficiency; correspondingly, sintering dust and fly ash had no obvious desulfurization and denitrification activities. For the mixture of activated carbon and dust, the coking dust reduced the desulfurization and denitrification efficiencies by blocking the pores of activated carbon, and its inhibiting effect on activated carbon was larger than its own desulfurization and denitrification activity. The sintering dust also reduced the desulfurization efficiency on the activated carbon while enhancing the denitrification efficiency. Fly ash blocked the pores of activated carbon and reduced its reaction activity. The reaction activity of coking dust mainly came from the surface functional groups, similar to that of activated carbon. The reaction activity of sintering dust mainly came from the oxidative property of Fe₂O₃, which oxidized NO to NO₂ and promoted the fast selectively catalytic reduction (SCR) of NO to form N₂. Sintering dust was activated by the joint action of activated carbon, and both had a coupling function. Sintering dust enhanced the adsorption and oxidation of NO, and activated carbon further promoted the reduction of NO_x by NH₃; thus, the denitrification efficiency increased by 5%-7% on the activated carbon.     

Chemical characteristics of road dust PM2.5 fraction in oasis cities at the margin of Tarim Basin

In order to understand the compositions characteristics of particulate matter with aerodynamic diameter less than 2.5 μm (PM_2.5) fraction in road dust (RD_2.5) of oasis cities on the edge of Tarim Basin, 30 road dust (RD) samples were collected in Kashi, Cele, and Yutian in the spring, 2018, and RD_2.5 was collected using the resuspension approach. Eight water-soluble ions, 39 trace elements and 8 fractions of carbon-containing species in PM_2.5 were analyzed. Ca²⁺ and Ca were the most abundant ions and elements in RD_2.5 (7.1% and 9.5%). Cl^- in RD_2.5 was affected not only by attributed to saline-alkali soils in oasis cities of the Tarim Basin and dust from Taklimakan Desert but also by human activities. Moreover, the organic carbon/elemental carbon (OC/EC) ratio indicated that carbon components in RD_2.5 in Cele town mainly come from fossil fuel combustion, while those in Yutian and Kashi mainly come from biomass combustion. It is noteworthy that high Ca in RD_2.5 was seriously affected by anthropogenic emissions, and high Na and K contents in RD_2.5 could be derived from soil and desert dust. It was estimated that Cd, Tl, Sn and Cr were emitted from anthropogenic emissions using the enrichment factor. The coefficients of divergence (COD) result indicated that the influence of local emission on road dust emission is greater than that of long-distance transmission. This study is the first time to comprehensively analyze the chemical characteristics of road dust in oasis cities, and the results provides the sources of road dust at the margin of Tarim Basin.     

Investigation to meet China II emission legislation for marine diesel engine with diesel methanol compound combustion technology

In order to reduce the pollutant emission and alleviate the pressure of petroleum resources shortage and greenhouse gas emission at the same time, the use of clean and renewable alternative fuel for marine engines is a promising option. In this study, a marine diesel engine, which was modified to run in diesel methanol compound combustion (DMCC) mode, was investigated. After the diesel injection parameters were calibrated, and combined with a sample after-treatment device DOC (diesel oxidation catalyst), the engine could meet the requirements of China II legislation. The overall MSP (methanol substitute percent) reached 54.1%. The value of each pollutant emission was much lower than that in China II emission legislation, and there was almost no methanol and formaldehyde emissions. When methanol was injected into the inlet manifold, the intake air temperature decreased a lot, as well as the exhaust gas temperature, which were beneficial to increase engine thermal efficiency and improve engine room environment. Compared with the engine running in pure diesel mode, when the engine ran in diesel/methanol dual fuel mode, the combustion phase was advanced, and the combustion duration became shorter. Therefore, the engine thermal efficiency increased, and fuel consumption decreased significantly.     

Metabolomic modulations in a freshwater microbial community exposed to the fungicide azoxystrobin

An effective broad-spectrum fungicide, azoxystrobin (AZ), has been widely detected in aquatic ecosystems, potentially affecting the growth of aquatic microorganisms. In the present study, the eukaryotic alga Monoraphidium sp. and the cyanobacterium Pseudanabaena sp. were exposed to AZ for 7 days. Our results showed that 0.2–0.5 mg/L concentrations of AZ slightly inhibited the growth of Monoraphidium sp. but stimulated Pseudanabaena sp. growth. Meanwhile, AZ treatment effectively increased the secretion of total organic carbon (TOC) in the culture media of the two species, and this phenomenon was also found in a freshwater microcosm experiment (containing the natural microbial community). We attempted to assess the effect of AZ on the function of aquatic microbial communities through metabolomic analysis and further explore the potential risks of this compound. The metabonomic profiles of the microcosm indicated that the most varied metabolites after AZ treatment were related to the citrate cycle (TCA), fatty acid biosynthesis and purine metabolism. We thereby inferred that the microbial community increased extracellular secretions by adjusting metabolic pathways, which might be a stress response to reduce AZ toxicity. Our results provide an important theoretical basis for further study of fungicide stress responses in aquatic microcosm microbial communities, as well as a good start for further explorations of AZ detoxification mechanisms, which will be valuable for the evaluation of AZ environmental risk.     

Photodegradation of Hexafluoropropylene Oxide Trimer Acid under UV Irradiation

As a novel alternative to traditional perfluoroalkyl substances (PFASs), including perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS), hexafluoroproplyene oxide trimer acid (HFPO-TA) has been detected worldwide in surface water. Moreover, recent researches have demonstrated that HFPO-TA has stronger bioaccumulation potential and higher hepatotoxicity than PFOA. To treat these contaminants e.g. PFOA and PFOS, some photochemical techniques by adding exogenous substances had been reported. However, there is still no report for the behavior of HFPO-TA itself under direct UV irradiation. The current study investigated the photo-transformation of HFPO-TA under UV irradiation in aqueous solution. After 72 hr photoreaction, 75% degradation ratio and 25% defluorination ratio were achieved under ambient condition. Reducing active species, i.e., hydrated electrons and active hydrogen atoms, generated from water splitting played dominant roles in degradation of HFPO-TA, which was confirmed by different effects of reaction atmospheres and quenching experiments. A possible degradation pathway was proposed based on the products identification and theoretical calculations. In general, HFPO-TA would be transformed into shorter-chain PFASs, including hexafluoropropylene oxide dimer acid (HFPO-DA), perfluoropropionic acid (PFA) and trifluoroacetate (TFA). This research provides basic information for HFPO-TA photodegradation process and is essential to develop novel remediation techniques for HFPO-TA and other alternatives with similar structures.     

Polycyclic aromatic hydrocarbons in benthos of the northern Bering Sea Shelf and Chukchi Sea Shelf

Eighteen polycyclic aromatic hydrocarbons (PAHs) were detected in benthos collected onboard the ‘Snow Dragon’ in the Northern Bering Sea Shelf and Chukchi Sea Shelf during the 6^th Chinese National Arctic Research Expedition (CHINARE 2014). Σ₁₈PAHs for all biota samples ranged from 34.2 to 128.1 ng/g dry weight (dw), with the highest concentration observed in fish muscle (Boreogadus saida) samples close to St. Lawrence Island. The PAH composition pattern was dominated by the presence of lighter 3 ring (57%) and 2 ring (28%) PAHs, indicating oil-related or petrogenic sources as important origins of PAH contamination. Concentrations of alkyl-PAHs (1-methylnaphthalene and 2-methylnaphthalene) were lower than their parent PAH (naphthalene) in all biological tissue, and their percentage also decreased significantly (p<0.05) compared with those in the corresponding sediment. There were no significant relationships between PAH concentrations and trophic levels, which is possibly due to the combined results of the complex benthic foodweb in the subarctic/Arctic shelf region, as well as a low assimilation/effective metabolism for PAHs. According to toxic potency evaluation results from TCDD toxic equivalents (TEQs) and BaP-equivalent (BaPE) values, whelk (Neptunea heros) and starfish (Ctenodiscus crispatus) are two macroinvertebrate species showing relatively higher dioxin-like toxicity and carcinogenic risk.